Search Documents

By T. Badrujaman

In September 2005, after 30 years experiencing in operating an ESF using a falling water film shell cooling system, Antam entered the new era in operating an ESF, after completely modernized its ESF No. 2 from a falling water film shell cooling system to a copper cooling system. Further, in the beginning of 2007, Ferronickel plant No. 3, where its ESF also uses copper coolers, was successfully commissioned. By operating an ESF using a copper cooling technology, Antam has to face some challenges to establish the operation stability. Besides that, the chances to maximize the furnace efficiency are greatly opened. The shielded-arc mode of electrode tip is selected to operate an ESF under relatively high furnace power to produce metal having tap temperature below 1500? and slag having tap temperature below 1600?. It leads to electric current unbalance. Further, operating an ESF using a copper cooler system under high voltage as consequence of the furnace power raise increases metal and slag tap temperature. This condition damages furnace integrity fast. Besides that, relatively high metal temperature increases its pressure during metal tapping. It leads to failure in closing the metal tap hole. The main different ways in operating an ESF using a falling water film shell cooling system and a copper cooling system lie in the electrode tip mode, the water specification used for cooler, metal tap block maintenance and allowed metal & slag level in furnace. Since a copper cooler system allows an ESF to be operated by consuming nickel ore having ratio Fe / Ni up to eight and producing slag having relatively high Fe content in slag, an undesirable silicon reversion phenomenon becomes an obstacle in reaching the operation stability. A copper cooler technology lets Antam to take a chance to increase its capacity. Modernizing the ESF No.2 had increased its furnace power from 17 MWh to 25 MWh. Meanwhile the ESF No. 3 can be operated up to 42 MWh. This technology allows an ESF to be operated under relatively high furnace power above 25 MWh safely as well as prolong the campaign life of ESF brick. Further, lowering ESF power consumption, extending the limitation of ratio S/M in nickel ore consumed and adjusting Ni grade in ferronickel product can be gained by applying this technology.

Jan 1, 2014

By Máximo Pérez, Julio C. Videla, Rosa Dzioba

"This paper reports the hydrometallurgical treatment of gravity concentrates of gold samples and outcrops associated with graphite ores obtained from:• flotation tailings of crystalline graphite minerals• outcrop samples of graphitic rock associated with auriferous minerals and free gold located in the Villa Union district and surrounding areas - La Rioja Province - Argentina.Previous studies of the flotation potential of crystalline graphite minerals failed to consider the presence of noble metals.The samples represent a mineralized zone of crystalline graphite which is distributed in different formations with a NE - SW trend in Maz, Punta Colorada and Las Ramaditas hills, covering an area of about 300 square kilometers."

Jan 1, 2003

By R. A. Kleiv, H. Havskjold, N. Church, T. Malvik, M. Tro, E. Larsen

Liberation is one of the major purposes of comminution in mineral processing. In the simplest form, two or more minerals are present in a particle and have to be reduced such that the individual particles contain only one mineral. The complexity of the mineral intergrowth varies from ore to ore. Poor magnetic separation of iron ore may have many causes. In this paper, the emphasis is given to the problem of fine magnetite inclusions in quartz or other gangue minerals. This is highlighted by two Norwegian cases: one on a magnetite ore and the other on a hematite/magnetite ore. The inclusions in question are so small that they are not liberated by reasonable grinding. In both cases, the result has been either poor recovery or lower grade concentrates than desired. The first example concerns production of direct reduction concentrates from magnetite. Magnetic inclusions in gangue particles will be magnetized enough for the particles to pass into the concentrate. The second example is given a more detailed study, where the problem is caused by silicates with small inclusions of magnetite in a combined LIMS and WHIMS separation. This study included microscopy, Davies tube testing, and magnetization measurements. In particular, large gangue particles with magnetite inclusions were shown to have a tendency to bypass the LIMS separators as drag forces in presence of hematite are large. Such particles will then be picked up by the WHIMS as their magnetization is higher than for hematite. This was demonstrated by Davies tube tests, which indicated that such particles were picked up in preference to hematite particles. However, the Davies results did not give a good quantification. Magnetization measurements of gangue particles with magnetite inclusions was shown to be a better tool to quantify the magnitude of the effect of magnetite inclusions in magnetic separation.

Jan 1, 2018

By Dilip Kumar Mohanty

In today?s world, Sustainability is the key issue before the mankind. With the ever-increasing population & unimaginable boost in industrial growth to cope up with a steady increase in demand and fast change in life style of a human being, the natural resources are exploited to such an extent that the very existence of living beings in this earth planet is threatened. In such devastating situation, the concept of Sustainability emerges out as a great savior. This concept focuses on minimum/ judicious use of natural resources, thereby preserving the resources for future generation while meeting the bare minimum requirement of the present generation. For an emerging economy like India, Mining and Mineral based industries form the back bone of our economic development. Thus, sustainability of mining and mineral processing industry has a far reaching impact on sustainable economic development of our nation. While at a macro-economic level, we have to strike a balance between economic development vis-à-vis socio-economic & environmental impacts, Industries have to ensure judicious and frugal use of natural resources by making use of energy efficient plants & machineries and adopting befitting technology for reduction & recycling of waste. In the context of the above, it would be interesting to look into the sustainability measures taken up by National Aluminium company (Nalco) at its Crushing & conveying plant at Panchpatmali Bauxite Mine, which is incidentally Asia?s largest Bauxite Mine. In the backdrop of the above stated facts, in this paper the authors make an attempt to bring out the sustainability issues in areas of energy conservation, environmental impact/pollution vis-a-vis mitigation measures adopted in crusher & conveyor plant of Panchpatmali Bauxite Mine & CSR / peripheral developmental activities undertaken by Nalco to mitigate the socio- economic impacts. Keywords: sustainability, energy efficiency, recycle, csr, peripheral development

Sep 1, 2012

By G. H. Lind

The Minerals Tertiary Education Council (MTEC), over the past decade, has worked closely with Australian higher education partners in metallurgical education to build capacity in this discipline to deliver high quality graduates for the Australian minerals-industry. This paper explores the benefits of industry engagement through a national innovative collaboration, the Metallurgical Education Partnership (MEP), and specifically the final year Process Design Project (PDP), over the four year period from 2008-2011. Some of the benefits discussed in this paper include outcomes of the student experience during an industry-intensive workshop, collaboration between higher education providers and aligning graduate attributes to meet industry requirements.

Sep 1, 2012

By G. K. Nimal Subasinghe

The performance of Knelson Concentrators (KC) used in gravity gold circuits often rely on manufacturers recommendations for selecting operating parameters such as, fluidising water flow rate and cycle time. These parameters are not only dependent on the machine parameters but also on the feed characteristics such as, size distribution of the gold and gangue particles and the composition of its constituent minerals. Particles entering a KC experience a centrifugal acceleration due to the high bowl rotational speeds. The required centripetal force to maintain a circular orbit is provided by the fluid drag force created by inwardly moving fluidising water and the Bagnold?s force arising from the particle/particle collisions. When the fluidising water flow rate is low particles move towards the outer rim of the bowl forming a packed bed within the grooves. On the other hand, if the fluidizing water flowrate is high the bed expands and some particles would move towards the centre of the bowl and gets carried to the tailings stream, thereby reducing the amount of material retained within the grooves of the bowl. Based on a force balance on a particle captured within the KC, a criterion which can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It has been shown that this criterion may be used to demarcate the transition of the bed from a packed-bed state to a fluidised state depending on the fluidizing water flowrate. By identifying the conditions for the optimal expansion of the bed comprising different constituent mineral particles, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. It was also observed that the accumulation of valuable mineral in the bowl takes place by the displacement of the gangue particles in the bed by the incoming heavy mineral particles. The kinetics of this segregation process was also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build up of heavy mineral reaches a maximum which could be used to identify the optimal cycle time. In this work, the suitability of the above model in optimizing the performance of a KC have been reviewed. Also the necessity and merits of testing an unaltered feed samples in a larger KC as op-posed to the commonly adopted GRG test has been discussed.

Jan 1, 2014

By Xiong Dahe

In recent years many creative technologies are applied to SLon vertical ring and pulsating high gradient magnetic separators. SLon-2500 and SLon-3000 vertical ring and pulsating high gradient magnetic separators are created towards larger scale. Through optimizing the magnetic system and lowering the electric current density, their energy consumption is obviously dropped. New magnetic matrixes are developed to raise the beneficial efficiency of valuable minerals. Special SLon vertical ring and pulsating high gradient magnetic separators are developed which can treat coarser particles of 0-5 mm. Through these technology creations, the mineral processing efficiency of SLon magnetic separators is further raised and their processing cost dropped. Therefore, they have been found wider applications. SLon-2500 applied in Essar Steel of India. In 2007, Essar Steel did a test on its Kirandul hematite ore with SLon magnetic separator and got very good results. The feed grade is 59.77%Fe, after SLon one roughing and one scavenging, the total iron concentrate grade is 65.00%Fe and iron recovery 93.86%. In 2008-2010, the company bought 10 SLon-2500 magnetic separators to treat such iron ores. In 2010 the first SLon-3000 was applied to processing ilmenite. The magnetite-ilmenite deposit is located in Pan Zhi Hua, Si Chuan Province of China. The ore processing flow sheet is: Drum low intensity magnetic separator is used to take out magnetite, and then the SLon-3000 is used to recover ilmenite for roughing. The mags of the SLon-3000 are further cleaned by flotation. The SLon-3000 average operational results are: feed grade 9.52%TiO2, mags grade 17.43%TiO2, mags mass ratio 41.01%, TiO2 recovery 75.09%, non-mags grade 4.02% TiO2, non-mags mass ratio 58.99%. SLon magnetic separators Applied to treat 0-5mm limonite: The feed of SLon magnetic separator is usually 0-2 mm which needs to be ground by ball mill. As many Chinese iron ores are poor grades, if we can throw part of tails before grinding, the grinding cost will be greatly reduced. In 2010, a SLon-1500 and a SLon-2000 were specially built to treat 0-5 mm limonite. The feed grade is 26.51%Fe, mags grade 53.20%Fe, iron recovery 64.26, and tails grade 13.66% Fe. SLon-2500 applied to purify quartz. In 2009, a SLon-2500 magnetic separator was applied to purify quartz in Shan Xi province. Its feed is 0-1mm quartz which contains 0.15%-0.25%Fe2O3, the designed non-mags grade need to be less 0.08% Fe2O3. The production results of SLon-2500 non-mags are 0.05-0.06% Fe2O3, much better than the designed data. SLon applied in Si Jia Ying Iron Mine to recover hematite. Si Jia Ying is a big oxidized iron mine located in He Bei Province of China. In 2005-2010, a plant annually treating 10 million tons of oxidized iron ore was built in which 39 SLon magnetic separators are applied. The total flow sheet results are: Feed grade 30.44%Fe, iron concentrate grade 66%Fe, iron recovery 80%Fe, tails grade 9.65Fe%. SLon applied to recover specularite. Li Lou Iron Mine in An Hui Province of China built a plant annually processing 5 million tons of iron ore in 2010-2011. 25 SLon-2000 magnetic separators are applied to recover specularite. The total flow sheet results are: Feed grade 31.65%Fe, iron concentrate grade 65%Fe, iron recovery 80%Fe, tails grade 10.37%Fe. SLon applied in Da Hong Shan Iron Mine. Da Hong Shan Iron Mine is located in Yun Nan province of China. It treats 4.5 million tons of oxidized iron ore annually. 15 SLon-2000 magnetic separators are applied to recover hematite. The total flow sheet results are: Feed grade 35.61%Fe, iron concentrate grade 64.95%Fe, iron recovery 74.08%Fe, tails grade 15.55%. Keywords: SLon magnetic separator, iron ore, ilmenite, quartz, beneficiation

Sep 1, 2012

By Milind Chikhale, Ranjeev Kumar, Keshav Tyagi

Ore characterisation including mineralogy and beneficiation testwork of an ore is very important for determination of possible products and their quality. The results of such study help in ascertaining the beneficiation process route for the ore. The present study deals with ore characterisation study and beneficiation testwork on the samples of hematite iron ore with goethite impurity. The characterisation study reveals that the hematite is under alteration stage to goethite which has become an integral part of hematite. High goethite/limonite content is enhancing the loss of ignition content of the ore and reducing its Fe content. The findings indicate that in case of hematite iron ore associated with goethite and limonite, it is difficult to achieve high grade of concentrate above 65% Fe. It depends on the amount of goethite and limonite minerals and their association with hematite. These minerals contain aluminous impurities and hence, their rejection becomes essential. Separation of limonite and of goethite to limited extent is possible. In case of goethite, effective liberation is not achieved where it occurs as surface alteration product of hematite grains. The gangue mineral reported are clay and gibbsite, and are closely associated with iron minerals. The test work results indicate the grade and recovery of Fe along with alumina and silica content in lumps, sinter fines and pellet feed fines that can be achieved for the different ore types vis-a-vis the percent of available hematite in the ore. The recovery of iron is dependent on the hematite available and the loss of iron values in tailings is more because of rejection of limonite and goethite.

Jan 1, 2014

By Jiajun Geand, Shuli Wang, Baodong Pan, Xueqi Cui, Guangwei Zhang, Jipeng Sun

Gravity-fed three-product dense medium cyclone(GTDMC)is usually used as the main coal washing equipment in coking coal preparation plant. It can produce three products with a low density suspension at the same time. Raw coal and dense medium are fed separately into the cyclone. Only the qualified low-density medium suspension is pumped into the cyclone while the raw coal is fed into the first-stage 1200mm cyclone axially at the top end by gravity. The 1200mm cyclone with a cylindrical form is for low-density separation. The clean coal with light density and slower-settling velocity moves directly towards the low pressure zone along the axis and is carried through the vortex-finder to the overflow. Only the heavy products pass through the "separating zones" to the wall of 1200mm cyclone and then migrate into the series-connected second-stage 850mm cyclone through the tangential outlet. The medium suspension from the first-stage cyclone is thickened and contains more magnetite coarse particles. The second-stage cyclone typically consists of a cylindrical section and conical part. These are all favorable for the second-stage cyclone to separate at a high density. Production practices show that the clean coal and the gangue rarely mixed in the middling, the lower limit of the separation is 0.2 mm, the Organic Efficiency and the Ecart probable of the first stage is 98.30% and 0.026 kg/L respectively.

Jan 1, 2014

By D. Jamróz, A. Surowiak, T. Niedoba, P. Pieta

"The separation of coal material of three types of coals originating from three various Polish hard coal mines (types 31, 34.2 and 35, according to Polish nomenclature, which were steam coal, semi-coking coal and coking coal) into particle size fractions and then into particle density fractions was done and then the following parameters were measured for each particle size-density fraction: combustion heat, ash contents, sulfur contents, volatile parts contents, analytic moisture. In this way a 7-dimensional vector of data was created. Using methods of factor analysis the important features of coal were selected, which decide about their membership to individual types. To evaluate the appropriateness of the applied method the Bartlett’s sphericity test as well coefficient of Kaiser-Mayer-Olkin (KMO) were used. To select important factors the Kaiser criterion and Cattell’s scree test were used. The obtained results were compared with the results obtained in previous works by means of observation tunnels method. The results showed which particular features are crucial to define the type of coal what is also important to select appropriate method of its enrichment.INTRODUCTION Coal extracted from the mine is often a mixture of coals of various quality originating, for example, from various coal layers. One of the most important issues is to determine its quality, what means to verify if it fulfills certain requirements. Usually, such parameters as combustion heat, ash contents, sulfur contents, volatile parts contents and analytic moisture decide what the coal quality is (Drzymala, 2009). Such investigations are expensive and time consuming. That is why it seems to be important to determine the mutual connections and interactions between them what would make possible to reduce the amount of the necessary parameters. This issue was already investigated with successes in several works [Jamróz and Niedoba, 2013; 2014; Niedoba, 2015]. This work is another approach to this problem. Here, the investigation of possible reduction of researched parameters was done on the basis of the factor analysis. The obtained results confirm the earlier observations."

Jan 1, 2018

By O. Güven

In recent years, there is an increasing demand on manganese consumption which stems from the important role of manganese in carbon steel production. And the growing need for manganese ores makes the beneficiation of low-grade manganese ores more economical. In this study, the characterization and beneficiation studies were carried out to propose a flow sheet for typical low-grade Turkish manganese ores. For this aim, different gravity separation methods were applied. According to the mineralogical analysis, the major mineral phases are pyrolusite (MnO2) and psilomelane (MnO2) while the major gangue mineral is radiolarite. Gravity separation tests were accomplished by using jigs, shaking table, MGS (Multi Gravity Separator) and in order to obtain products with high Mn ratio, high intensity magnetic separation was also performed. As a result, different combinations of flow sheets were utilized and a concentrate assaying 56.5% Mn with 85 % recovery was obtained.

Sep 1, 2012

By Lorenzo Reyes-Bozo, Ronaldo Herrera-Urbina, Pablo Higueras, Alex Godoy-Faúndez

"The copper mining industry in Chile and perhaps in other countries as well is faced with the challenge to implement the best practices in order to achieve a sustainable and more environment-friendly growth. Relationships between mining industry and society have been historically complex due to its environmental impacts. Whereas the ore grade has declined continuously, this has involved an intensive energy and water consumption thus increasing operational costs at different stages of the concentration process. In the case of copper sulphide ore concentration, froth flotation is the main technology used worldwide. The amount of the different chemical reagents used in flotation plants (i.e., collectors, depressants, frothers and modifiers) affects significantly production costs and has a negative effect on the environment as well. The objective of this research work was to evaluate the use of biosolids and their main components (i.e., glucose, proteins and humic substances) as more environment-friendly flotation collectors for chalcopyrite and molybdenite. For this purpose, microflotation tests were conducted in a modified Hallimond tube. In addition, FTIR and zeta potential experiments were performed to investigate the interaction of biosolids with these sulphide minerals. Biosolids and their main components may interact through physical and chemical ways due to different affinities with such sulphide minerals as chalcopyrite, pyrite and molybdenite, which are present in copper sulphide ores. In alkaline pHs, biosolids and their main components make the zeta potential of the sulphide minerals investigated more negative. These results may provide important information concerning the behavior of the main sulphide minerals in the concentration of copper sulphide ores at industrial scale, wherein mill processes could affect their surfaces properties. Therefore, biosolids and their main components may open an opportunity to be used in copper sulphide flotation plants to partially replace conventional reagents, which are more hazardous and less environment-friendly."

Jan 1, 2014

By Y. P. Huang

Experiment results and operation practice on reutilizing old tailings dumped at SCIM (Shang-chang Iron Mine) of KISCO (Kunming Iron and Steel Corp.) are presented. In a production period over 30 years SCIM dumped about 8 million tons of iron ore tailings. For improving resources utilization instead of wasting, experiments on processing for reutilization of the old tailings are con-ducted. These tailings are fine size fractions of weathered iluvial ores rejected out by classification- des-liming in ore washing and dressing processes, containing TFe 21%~22% in hematite mainly and limonite occasionally. Their particle size distribution, in average, is of 72.26% minus 0.037mm and 30.88% minus 0.005mm. Existence of plenty of micro-fine particles makes the tailings refractory to process, resulting in poor metallurgy. The whole sample of the old tailings without size-classification is fed into experimental process. Slon-100 type high grads WHIMS (wet high intensity magnetic separator) with cyc-pulsing is adopted, which magnetism-focusing rod?s diameter is changed from 3mm into 2mm. Operational conditions of optimizing rougher separation tests are strengthened. An iron concentrate assaying 52.21% Fe at quantity rate of 18.39% and iron recovery of 44.40% is obtained. Operational practice shows that metallurgy and economy of the old tailings treatment are close to what achieved at experiments. It is estimated, therefore, that some 1.4 million tons of this iron concentrate may be recovered from the old tailings. This means that KISCO has moved its key one-step in re-mining and reutilizing the secondary resources, which would be a good demonstration in this industry. This is also of social and economic significance in response to China government?s request on reducing consumption of resources and establishing society with economy for achieving sustainable development.

Jan 1, 2014

By Larry A. Cramer

"Three primary drivers are setting the trend for base and precious metal processing . they are: continued low real base metal prices, environmental concerns, and continued high prices for PGM.s. Low base metal prices are increasing the search for economies of scale and company consolidation as well as the development of some hydrometallurgical technologies. Environmental concerns are pushing for continued reductions in SO2 emissions and hydrometallurgical technologies. The high prices for PGM.s are driving major expansions and a focus on minerals processing recoveries and, to a lesser extent, reductions in the refining metal lockup.In nickel, HPAL operations on laterites have failed economically but Inco is still pursuing some alternatives. BHP-Billiton and others are developing bioleaching alternatives for nickel laterites and sulphides.Copper continues to be dominated by the hydrometallurgical and pyrometallurgical debate; new hydrometallurgical developments are being tested at several sites whilst the pyrometallurgists continue to make competitive cost and environmental improvements.Gold processing developments are dominated by the use of improved gravity recovery equipment and by the development of thiosulphate as a more environmentally acceptable lixiviant.PGM processing trends are the use of fine grinding technologies, higher power input flotation cells, and new pyrometallurgical technologies. Hydrometallurgical options for some applications are being sought.OVERVIEW The metals industry has remained under price pressure for some time; low and decreasing real prices for most metals have become an expected scenario. Occasional price spikes give some relief but invariably bring expansions and new entrants into an already oversupplied commodity market, thus leading to the continued price pressure. Technical innovation, economies of scale, and improved work systems are continually sought, so as to improve the competitive position of each individual company in such a climate; however, these developments add to the downward price pressure. In such a situation the application of scarce funds to research and development is a difficult task. Excess funding is not available in tight economic times and yet the main route to higher profits is clearly the application of technical developments to lower the cost of producing a metal commodity. Many technical centers have closed as a cost saving exercise and some have coalesced to obtain economies of scale. The Australian based AMIRA research organisation has grown to serve the R&D part of the market well in Australia and in South Africa by acting as the catalyst to form research partnerships between a number of industry players and as an administrator to direct the funding of research projects towards the various applicable research institutions. AMIRA has developed closer ties to Camiro (Canadian Mining Research Organisation) through the appointment of Camiro.s metallurgical processing research director as AMIRA.s North American based director. AMIRA is continuing discussions with MIRO (Minerals Industry Research Organisation) in regard to a merger, with a report outlining the merger proposal expected in March of 2003. Company focused research centers continue to be effective at Anglo American Research Labs, Teck-Cominco Research, Falconbridge Research center, Inco Research and some others."

Jan 1, 2003

By V. Runkana, N. K. V. Nadimpalli, S. Sahu

"IsaMill™ has been in operation in the recent past for fine grinding of low grade ores to extract non-ferrous minerals. IsaMill™, typically, consists of a series of uniformly spaced identical disks mounted on a rotating shaft which is encased in an outer shell. The mill offers high energy efficiency for fine grinding and an inherent scalability. But, it encounters certain operational challenges such as non-uniform distribution of grinding media coupled with high wear rate of the disks and solid walls of the mill at specific locations—which adversely affect the mill performance. To circumvent these operational challenges, design modification of the disks through heuristics, by introducing a reduced diameter disk (RDD) at specific locations, is a common practice in industry. But there is no systematic scientific study in this regard. In the current work, we developed a discrete element method (DEM) based model and simulated for the IsaMill™ operation to study the effect of RDD on the efficiency of the mill and wear rate of the solid walls and disks. Since the first set of disks experience the high wear rate due to the high loading of the charge, the RDD was introduced at the first two disks. The simulations were performed at different diameters of the RDDs and at different media loadings. The performance of the mill was analyzed based on the power consumption, the wear rate on disks and the distribution of media particles inside the mill. Besides, the performance variables such as mean velocity of media particles and total impact energy provided useful insights into the milling operation. It was observed that the reduction in disk diameter yields lower wear rate of the disks at the cost of decrease in power draw at a constant high media loading. Whereas, when the media loading was decreased, the amount of wear and power drawn was comparable for both the most reduced and least reduced disk diameters. Therefore, there is an optimum choice of RDD for a given mill loading to maximize the mill performance while reducing the wear rate of the disks."

Jan 1, 2018

By S. M. Narbekova, L. V. Semushkina, Zh. A. Aldybayeva, A. A. Mukhanova, D. K. Turysbekov, N. K. Tussupbayev

More complex and heavy-concentrating oxidized and mixed sulphidic oxidized ores are involved in production because of increasing needs for non-ferrous metals. Extraction of the oxidized minerals of non-ferrous metals general in current technologies. The problem is solved to oxidized polymetallic ores the preliminary selective sulphidization is the oxidized surface of the components by means of hydrogen sulphide, sulphide and calcium polysulphide, and also element sulphur, etc. The task was to study details of flotation of the oxidized lead-bearing ore of the Zarechnoe deposit (Kazakhstan) with calcium polysulphide as sulphidation. According to chemical analysis initial samples of the ore contain, %: lead – 4.8; zinc – 0.1; general iron – 0.81. Phase structure lead is characterized by the oxidized form of 57.76-64.5 %; by sulphidic status of 25.5-32.64 %, and by plyumboyarosite of 19.0-23.02 %. Researches on flotation beneficiation of oxidized lead-bearing ore are conducted. Sulfidizator gave to grinding, on flotations there were used the collector (butyl xanthogenate of sodium) and frother (T-80). Experiments were conducted with a new sulphidizator – calcium polysulphide. The latter is obtained by interaction of CaO calcium oxide with sulfur and water at high temperature with component mass the following ratio S:CaO:H2O =10:5:85. Extent of mill initial ore was optimised (88.42 % of - 0.071 mm grade). For the optimum mill mode the studies on matching of an optimized consumption of sulphidizators are performed. On basic technology with application of sulphide of sodium as a sulphidizator at optimum mill, the lead concentrate with the content of lead 64.4 % at extraction of 86.6 % was received. The content of cerussite in a concentrate was about 14.9 % at extraction of 82.1 %. With application of calcium polysulphide as a sulphidizator the lead concentrate with the content of lead 68.0 % at extraction of 88.0 % was received. The content of cerussite has made 16.0 % at extraction of 85.0 %. Application of a new sulphidizator allows to increase extraction of lead in a concentrate from 64.4% to 68% and cerussite extraction – from 82.1 % to 85.0 %. The possibility of application of calcium polysulphide as a sulphidizator instead of conventional sulphurous sodium was established.

Jan 1, 2018

By Francesco Vegliò, Luigi Toro, Francesca Beolchini, Francesca Pagnanelli, Stefano Ubaldini

"Biosorption is an innovative technology used to remove heavy metals from aqueous solutions from mining waters and other industrial wastes. A wider application of this alternative process is strictly dependent on the understanding of the chemico-physical aspects involved, in order to optimize the operating conditions. Mechanistic models are the most useful tools used for understanding purposes, even if the empirical models are still widely applied for their simplicity.In this paper especially propagated biomasses of Sphaerotilus natans, calcium alginate and some waste materials were tested as adsorbents for single and binary solutions containing heavy metals at different pH. The equilibrium experimental results were fitted according to empirical and physical models with growing complexity outlining the inadequacy of the predictive models; in fact, the non-ideal interactions among metals require the insertion of additional correction parameters."

Jan 1, 2003

By Liping Yu Che, Xiaotie Wang, Mingli Cao, Jizu Yongfu Yuan

"It is difficult separating fluorite from Ca, Ba, Si intergrowth minerals than simple from Si, using common reagents such as combination of oleic acid or paraffin soap and water glass, but the finest quality fluorite concentrate whose grade is over 96%F must be required in chemical plant.This paper studies the flotation process of native fluorite from calcite, barite and silicate minerals whose flotation properties is similar to fluorite, using new effective collector H602 and new depressor S602 that is cheaper in cost, and describes the flotation properties. In order to determine optimum flotation separation condition, the effect of pulp pH, pulp temperature, pulp density and the effect of dosage of reagents on flotation were investigated and the flotation result was provided by oleic acid collector and the results of collector H602 were compared with those of collector oleic acid in the test. The test result of ore samples shows that at moderate pulp pH values (10.5-11.5) and other moderate technical conditions, the fluorite mineral can be obtained by new reagents and the rational reagents combination. The conclusion is 98%F of fluorite concentrate can be obtained, using the combination of H602 and S602 and only 5 steps in techniques. The paper discusses the mechanism of the flotation separation of fluorite mineral from intergrowth minerals."

Jan 1, 2003

By R. T. Dec

Current industrial compacting and briquetting practices are largely based on trial-and-error techniques. This paper introduces a two-dimensional finite element model of briquetting process in the roller press. Compared with other modeling techniques used in the past, finite element method offers the most versatile approach because it incorporates adequate information about powder behavior, geometry and frictional conditions and offers predictions for the density distribution, the velocity field, the stress distribution, roll force and torque. More over, when the model includes elasticity, it offers predictions on the internal stress state in the briquette after its exit from the roll. This enables to perform realistic computer experiments which are helpful for establishing the forming cavity geometry and process conditions necessary to produce briquettes with the desired properties. Three forming cavity profiles are analyzed. Results from model are verified on experimental roller press and best cavity profile is recommended for briquetting of sub bituminous coal fines.

Jan 1, 2014

By Kaustubh Joshi, Pradip, Beena Rai, Venugopal Tammishetti

"Rapid depletion of high grade iron ores coupled with the increasing demand for the blast furnace grade iron ore in recent times has shifted the research focus on the development of appropriate technologies for the utilization of low - grade alumina rich iron ore slimes. These slimes are currently being dumped into tailing ponds owing to their high alumina content. Typical constituent minerals present in the Indian iron ore slimes are hematite, goethite, gibbsite and kaolinite. Considering the fine particle size distribution (<37 microns) in the slimes, selective dispersion-flocculation seems to be one of the most appropriate process which has been explored by us. We present our successful results on a natural iron ore slime sample obtained from one of the mines in India. We have been able to achieve a concentrate assaying >67% Fe, and <3% Al2O3 and 2.8% loss on ignition (LOI) from the slime sample assaying 60.4% Fe, 7.7% Al2O3 and 5.45% LOI with an Fe recovery of 62-69% simply by adjusting the pulp pH. We have scaled up the process to a semi batch scale as a prelude to commercialize it for the beneficiation of low grade iron ore slimes."

Jan 1, 2014