Search Documents

By Wayne van Drunnick, Mervyn Ruthnasamy, Olvier Guyot, Christophe Bouché

"Anglogold’s Mponeng Mine is situated in South Africa’s North West Province approximately 80km from Johannesburg. The reefs being mined in this area are among the deepest deep level mining operations in the world. These shafts often exceed several thousand meters making these operations complex and expensive.The gold plant is fed with run-of-mine ore which is stored in mill silos. Feedrate to the mills is controlled by a variable speed belt. Three parallel SAG mills (4.85 x 9m) treat 80-100tph, operating in closed circuit. Hydrocyclones classify the mill discharge, returning the oversize to the mill feed. Cyclone feed density and pressure are measured and are used with typical control loops to determine water addition rates to the mill. Control loops at PLC/SCADA level were historically used with limited success in the control of the milling circuits. Mill control for an installation of this type used mill mass (measured by load cells) and feedrate to control throughput. An online particle size analyser (PSI) was installed to assist grind control in tandem with pressure/density control on the cyclones. Although the accuracy of the measured grind was reliable, long term consistency of the PSI could not be guaranteed. Economic pressure from the business sector requires consistent mill throughput at optimum grind conditions. Fluctuations in production targets can manifest due to inconsistent control and the lack of real-time information from the process.This sensitivity to process movements may vary between shifts and also with changes in ore competency.Whilst tools are available to improve control, few have the sensitivity to process movements to provide real-time information for optimal grind control. For this reason an Advanced Control solution was sought. Advanced Control is often described as the supervision of basic PLC/SCADA control. Advanced control systems have to seamlessly compliment the existing control strategy and bridge the gap that exists between basic control and optimised control. A solution was found in the Metso Minerals CISA’s OCS (Optimising Control System). This French designed system makes changes to process setpoints to achieve peak performance and is distinguished from others by its soft sensor capabilities. The soft sensor is an embedded module in the OCS package that can be configured to estimate values normally obtained from field instruments. Advanced control using a Fuzzy Expert System assisted by Statistical tools (such as moving averages and a Soft Sensor using Phenomenological Models) would serve to bridge that gap. Metso Minerals CISA’s OCS is a modular system with various capabilities.It was successfully used to provide on-time process information via Soft Sensors. Circuit stability was achieved using Rule Based Expert Control in complete synergy with Fuzzy Logic. Two rule-based strategies were developed for this circuit. The first uses the online product size analyser as a primary control variable. The second uses a calculated kWh/t value and a modelled mill discharge density as primary control variables. The latter had more availability than the particle analyser and is currently in use."

Jan 1, 2003

By P. A. Harvey

Previous studies have reported that inorganic electrolytes can enhance floatability of coal. The research has shown that the enhancement, if any, is highly dependent on changes in solution pH, type of electrolyte, and electrolyte concentration. The reasons for this are still not clear. In this study the floatability of coal particles in mono and divalent salt solutions was investigated. The zeta potential and hydrophobicity of the coal was measured experimentally, and a modified Hallimond tube was used to determine the floatability of coal particles by single bubbles, where the collision efficiency was equal to unity. The experimental information was used in conjunction with the Hogg-Healy-Fuerstenau equation to quantify the electrical double layer interaction. It was found that for low electrolyte concentration (less than 0.1 M) solutions the flotation recovery of coal particles was less than that for distilled water, and decreased with increase in concentration. Conversely, at electrolyte concentrations above 0.1 M, flotation recovery increased with increasing concentration (Figure 1). Both of these results are consistent with previous observations, but are inconsistent with expectations when considering the possible influence of electrical double layer interaction. Modelling of the system indicates that the electrical double layer is compressed with increasing electrolyte concentration, resulting in an increase in flotation recovery due to a diminishing of the (electrical double layer) repulsion between the bubble and the coal particles. Moreover, for electrolyte concentrations above about 0.1 M the electrical double layer is completely depressed and would have little further influence, if any, on the flotation process. Therefore, the electrical double layer interaction is not the principal determining factor for the flotation of coal in electrolyte solutions.

Jan 1, 2003

By Sathyaprasad Nanjundaiah

The Paper intends to showcase a framework for spatial data collaboration from multiple sources of data, in order to create a single source of truth across the Organization. The framework is targeted to reduce the data duplicity, re-work, time loss due to search of required data and hindrances to fetch or transfer data from various data sources. The spatial data collaboration will provide a single window view of the entire organization with respect to its operations, management, sales, customers and competitors on a spatial reference across various regions in the World. Large Organizations with cross-country operations can standardize the use of spatial data through this framework for ease of data access, increasing the data reliability / integrity and better / on time decision making. Keywords: spatial data, GIS, collaboration, framework, mining, ESRI, tab files, shape files, ETL, reliability, integrity, interoperability, geo data, geo database, single source of truth

Sep 1, 2012

By Sami Makni, Ahmed Bouajila

"To remain competitive in an open market, mining companies are more and more requested to optimise their complex and highly multivariate processes. The increasing amount of process data, brought about by intensive use of instrumentation and the progress in computer data acquisition, enhances the need for more and more powerful and robust tools for the analysis and modelling of the process data. Now, with the emergence of multivariate data analysis (MDA) techniques, on-line clustering of mineral process behaviour is possible and could help in the extraction of valuable process operation indicators. MDA can be used in different mineral processes such as flotation, grinding, smelting etc.In this paper, we focus on grinding process considered as the most costly and power consuming node of the mineral processing scheme. Different objective-oriented levels of data clustering will be addressed.First, the evaluation of grinding operation taking into account data and constraints from all processes before (e.g. blasting, crushing) and after (e.g. flotation, leaching, etc.) the grinding node. The second level deals with process diagnosis by differentiating operation level and identifying behaviour drifts. Control and optimisation are two other levels concerned here with the selection of optimum trajectories in the drift correct.Industrial plant data are processed in order to illustrate the feasibility and the potentiality of MDA applications in addressing the clustering and interpretation of grinding mill behaviour."

Jan 1, 2003

By Gregory Harbort, Sarah K. DeBono, Alan J. Monaghan, Emmanual V. Manlapig

"The Jameson Cell is a type of flotation machine in which air and pulp are brought together in a vertical tube called a downcomer. Within the downcomer the air and pulp are dispersed into a dense foam of fine bubbles, which creates a favourable environment for bubble-particle collision and subsequent collection of hydrophobic particles. The intense collection zone within the downcomer can be considered similar to the zone between the rotor and stator in mechanical flotation cells.Research into the bubble-particle collision and fluid dynamics of mechanical cells rotor-stator zone has been limited by the difficulty of achieving accurate measurements in production sized machines. With the Jameson Cell the downcomer is largely external and separated from the flotation tank, allowing ready access to the primary contacting zone for measurement and analysis.An investigation has been undertaken into the operating characteristics of the downcomer relating to bubble-particle collision. An effective mapping of the downcomer has been made through measurements of void fraction and bubble size taken across cross sections of the downcomer. Analysis of these measurements has provided an interpretation of the variations in the air and fluid dynamics, bubble size and distribution throughout the downcomer chamber.Existing models of bubble-particle collision efficiency are reviewed in respect to the collected information and refinements conducted. The area of maximum bubble-particle collision efficiency is defined. Findings are related to operation within the rotor-stator zone of mechanical flotation cells."

Jan 1, 2003

By Peter Ay, Harry Pempel, Satya Narra, Mike Müller, Jens Markowski

"Within the next few years major changes in mobility are expected. Increasing numbers of electric powered cars, electrobikes and E-Scooters define the transport sector. Recently lithium based traction batteries as storage medium have led into matrurity of series production combining high electrical efficiencies with low weights and compact dimensions. Due to the relatively young development with lithium batteries utilization, only few investigation were conducted regarding their recycling. Conventional battery recycling processes can not be applied due to differences in design and chemistry. So an automated disassembly and processing procedure for lithium traction batteries has been developed in the R/D-project ""Li-WERT"". Instead of complete smelting of the batteries without pretreatment, an automated disassembly and specific treatment of the material streams was realised, adjusted to the needs of the subsequent recovery technologies. A higher quality, with reduced expenses for the separation of fine-grained or fused material mixes, can be obtained for the individual components. The automated disassembly using an industrial robot significantly reduces dangers for the operating crew. The selective disassembly and beneficiation allows full recovery of the fractions. The batteries will be disassembled to cell level by the industrial robot. Anodes, cathodes, and separation layers are isolated and processed. The technology is designed, that no waste is generated for disposal. The pelletised cathode coating and the other separated metals (stainless steel, copper, aluminum) can be used in respective metallurgical plants. Circuit boards and plug contacts are also coveted secondary raw materials for reuse. The process is modular and offers high flexibility, e. g. for new battery types/ sizes by quick adjustment of the robot and tool change. Adaptation to other cathode materials (e. g. Li[FePO]) is possible. After finishing the R/D-project, a pilot plant for demontage was realised in 2013."

Jan 1, 2014

By Carlos Pereira, Fábio de São José, Francielle Nogueira

Votorantim Metals Corporation is one of the leader companies in the extraction of zinc in Brazil. One of its mines, located in the city of Vazante - MG, was composed by zinc silicate ores, but recent studies have indicated a change in mineralization type with arise of zinc sulphide’s ore bodies with disseminations of galena (PbS) and silver. The liberation size between sphalerite and galena in this ore occurs in very fine granulometry (approximately 18µm), fact that has negatively influenced into the flotation process. Aiming to reduce this problem, studies about the use of dispersing in the flotation process have started. Thus, this study investigated the action of different reagents dispersing on the stability of the suspensions. The tests were carried out with samples of mineral galena and sphalerite using four types of dispersing within two different dosages and two pH. The reagents tested were sodium hexametaphosphate, sodium silicate, carboxymethiylcellulose, and sodium polyacrylate. The results of the dispersion tests were analysed in relation to dispersion index. The tests with hexametaphosphate showed high dispersion for both galena and sphalerite. The sodium polyacrylate and arboxymethiylcellulose showed a high dispersion index for galena and a low index for sphalerite implying that reagent can be used in the concentration process of galena.

Jan 1, 2014

By Hugo Barrientos

"The growing need to optimize the mining processes produces a need for users to have a simple, reliable, secure and cost-effective method to monitor the values of the variables measured in field. The solutions described in this paper, we will demonstrate how the implementation of Emerson Smart Wireless technology helps to optimize the leaching and electro winning processes. An effective monitoring of the variables involved in the operation of a heap leach, such as pressure, flow rate, pH, water level control and regulator valves can improve production and optimize the use of sulfuric acid, which results in a more effective management of resources and helps reducing input costs. Moreover, the constant monitoring of variables prevents the risk of landslides, reducing maintenance costs. In electro winning cells, the wireless solution measures variables such as pressure, flow rate, temperature and voltage provides a performance indicator for the entire operation, capable of detecting and predicting shorts, and monitoring the overall functioning of a cell or group of cells. As a result of the applications studied, users can monitor variables in real time, optimizing the use of resources, quickly detecting possible flaws in the process and reducing the risks in the operation. All these factors have a direct impact on company results."

Jan 1, 2014

By O. A. Punishko, G. G. Mineev, Zabaikalsky Ore-Dressing Plant, M. V. Malova, O. V. Belousova, S. A. Bogidaev

"In order to intensify benefication processes (flotation and magnetic separation) for rebellious tantalitecolumbite ores electrochemical machining of pulp (ECM) is suggested instead of costly mechanic-chemical activation and magnetizing roasting. Any change in the surface mineral-semiconductor potential under the action of electrochemical treatment results in the change in the isoelectrical state of the surface and the adsorption property of the mineral with respect to ionogenic reagents-collectors. In this case conditions are created for regulating the ion composition, reduction-oxidation potential and pH of the liquid phase of the pulp without any extra introduction of expensive and often ecologically harmful chemical substances.Ores containing tantalum and niobium are characterized by complex chemical composition, determining their physical properties (conductivity, dielectric penetration, magnetization value, etc.) and their electric susceptibility.The authors investigations show that the pulp electrochemical treatment leads to the increasing magnetic susceptibility of the paramagnetic minerals. The main chemical elements forming the columbite-tantalite minerals except tantalum and niobium are iron and manganese. They determine the rare-metal minerals paramagnets properties. The electrochemical treatment changes the relation of the oxidized and reduced forms of these elements having. The method of cathode pulp treatment before flotation is successfully tested industrially.In the field of noble metals metallurgy new technological proposals are reduced to the following. As is know, the production of noble metals from unusual raw materials demands the elaboration of principally new technologies new technologies in so far as the methods for gold and silver extraction from ores are as a rule low elective and at the existing level of engineering are economically not expedient.The analysis of the main trends in the field of non-standard raw material treatment shows that the perspective ones are the geo- and biotechnological processes (underground leaching and leaching in heaps - UL and HL and microbiological methods of metal extraction)."

Jan 1, 2003

By Rogerio C. Guimarães, Antonio E. C. Peres

The production of phosphate concentrates (phosphate rock) from slimes represents a challenge to the phosphate industry worldwide. In Brazil, this challenge is particularly relevant due to the consistently low P2O5 grades and the igneous origin. The first industrial experiences of producing phosphate rock from slimes (-44µm or -325#) fraction started at Arafertil, currently Bunge Fertilizantes SA, in Araxá, in the 1980.s. This production corresponds, nowadays, to 35% of the total production of concentrates in the company (830,000t/year) in a circuit consisting of desliming in 40mm microcyclones and concentration in flotation columns, corn starch and fatty acids being utilised as reagents. The performance of slimes flotation and the process control, at Bunge´s concentrator, were improved after the introduction of column flotation technology, in the first half of the nineties. The column flotation technology for slimes recovery was expanded to other Brazilian concentrators still in the nineties: Ultrafértil (Catalão - GO), Bunge (Cajati - SP), Fosfértil (Tapira - MG) and Copebrás (Catalão - GO). At present the Brazilian production of phosphate rock is approximately 4.5Mt/year, with a strong trend for a market increase. Genuinely Brazilian technology is utilised for the processing of slimes, the concentrates representing 11 to 13% of the overall production. The production of apatite concentrates from slimes was relevant to increase phosphate recovery and reduce costs, contributing to the growth of the fertilisers industry.

Jan 1, 2003

By Heribert F. Broicher, Arne Volland

The application of remote sensing techniques combined with fluorescence spectroscopy is realised in analytical devices called LIF Analysers. The analysis of laser-induced fluorescence facilitates non-destructive, non-contact, on-line and real-time rock identification and quality control of bulk solids in transport. LKAB of Sweden was the first company to test LIF Analysers in the Kiruna Mine for bulk sorting of run-of-mine ores depending on the phosphorus content. Other applications tested in Germany so far are quality control of limestone (iron and/or dolomite content) and rock identification in lignite mining. Of special interest also is rock identification in diamond mines for dilution control. The paper summarises the present state of the application of LIF Analysers.

Jan 1, 2003

By M. Naymanbayev

The characteristics of the mineral composition of ores and valuable set of components: the technology of processing depending on the type of mineralization, the nature of the impregnation of ore minerals and their composition have been considered. There have been given technological schemes for processing concrete objects. The analysis of fitness fields for industrial development (degree of scrutiny, the effectiveness of developed enrichment and hydrometallurgy technology) has been provided.

Sep 1, 2012

By Paul W. Cleary

"Particle scale simulation of industrial particle flows using DEM (Discrete Element Method) offers the opportunity for better understanding the flow dynamics leading to improvements in equipment design and operation that can potentially lead to large increases in efficiency, throughput or product quality. DEM has been used for modelling many industrial applications, particularly milling. This includes ball and rock motions and power consumption in ball mills, AG and SAG mills, vibrational segregation, flows in rotating drums, operation of dragline excavators and hopper flows. In mineral processing, DEM has been concentrated on mills because of their critical importance. However DEM also offers the opportunity to improve many other parts of mineral processing operations. These areas often do not receive the attention that the key comminution equipment commands, but can become critical when they fail or under-perform. Importantly their assessment/improvement using DEM is often much more feasible because of smaller problem sizes and the absence of poorly understood physics such as breakage. In this paper we describe DEM simulations of four important pieces of non-comminution equipment that are commonly found in or near mineral processing plants (these are shown in Figure 1):"

Jan 1, 2003

By Robinson Irarrazabal, Edison Collinao, Rodrigo de Carvalho, Patricio Davila, Marcelo Tavares

"In recent years, DEM (discrete element method) softwares, along with 3D laser measuring equipment, have become powerful tools to describe mill charge behavior, as well as forces acting on the liners of SAG mills. With the aim of contributing to streamline this application of the advanced technologies ME Elecmetal and Universidade Federal do Rio de Janeiro, UFRJ, proposed a new approach to improve the design of mill liners using elements from mechanistic modeling of grinding. The paper presents a methodology for continuous improvement of liner design, which uses information from the DEM collision energy spectra in the mill discriminated for the different components (ore and steel balls), as well as information on the breakage properties of the ore being ground. From these it proposes the concept of "effective collisions", which corresponds to the collisions that are of sufficient magnitude to cause breakage, thus allowing to discriminate from impacts that do not cause breakage either in a first impact or after repeated loading. It also tracks the collision of steel balls against the shell in order to assess their potential damage to the liners. An industrial case study is presented of a 38’ diameter SAG mill, which was experiencing challenges associated to liner breakage and low efficiency with the old liner design. Through a modification of the liner design, simulations demonstrated the potential benefit associated to reduction in ultraprojection and improvement in mill capacity. Implementation of the new design in the SAG mill was carried out, resulting in increase in daily throughput from 6 to 12%. Further, the time spent in liner change was reduced by 47% given the reduction in the numbers of parts. This operation also benefited from having no stops due to unplanned shutdowns to replace broken tiles. These demonstrate the benefit of coupling advanced computational tools to sound engineering principles in continuous improvement of liners."

Jan 1, 2014

By Rajamani R. K.

The design of tumbling mills has progressed from the Bond work index concept of the 1950s to the population balance concept of the 1980s and then made a quantum leap forward with the discrete element method in the 1990s. The failure of a SAG mill at the Grasberg mine site set in motion the inquiry into the role of shell lifter geometry on the profile of the charge motion within the mill. Quickly, it became evident that this could only be accomplished by tracking individual motion of ore particles and grinding balls and not by study of en masse motion of the charge that had been established previously. The discrete element method (DEM) which was prevalent in the civil engineering literature at that time proved suitable to tackle this simulation problem. In 1991, the two dimensional simulation of laboratory scale mills was validated with the DEM. Later this simulation method evolved into ?MillSoft?? a simulation software package for the design of lifters in ball and SAG mills. MillSoft?simulations proved that cataracting charge motion is not conducive to the life of lifters. The old rule of thumb that the number of shell lifter rows should equal twice the diameter of mill in feet was shattered by simulation results. Instead, the number of rows equal to the diameter of the mill in feet, providing that the lead angle of lifter is around 25 degrees, was established as being more optimal. This bold design change was first implemented and tested by Mark Sherman at Alumbrera Mines in Argentina. Two 36-ft SAG mills responded extremely positively to the design change. This success was immediately repeated at Collahuasi, Pelambres and other mines in South America. The design change has so far exceeded expectation that there is not a single SAG mill around the world today that does not employ a relief angle on its shell lifter. The DEM method has advanced in the hands of the author, mining companies and universities, notably in Australia and South Africa. Today, three-dimensional simulation of charge profile and slurry transport is a standard in the design of mills. There is strong pursuit of a virtual comminution machine with DEM in Australia. In South Africa, an experimental method known as positron emission tracking is emerging as a method for tracking particles in grinding mills. The computational burden of computing with millions of particles in three-dimensional simulations has been eased to less than a day with a technique known as GPU computing. Keywords: DEM method, GPU computing, SAG mill, tumbling mill simulation, discrete element method

Sep 1, 2012

By Markus A. Reuter, Yongxiang Yang, Jim R. Post

In the upper part of an iron making blast furnace, sinter, coke and pellets are charged. While descending, the burden is heated and the iron oxides are reduced by the rising gases. The iron oxides start to soften and eventually melt. The melt and the remaining coke collect in the lower part of the blast furnace: the hearth. The remaining coke forms a porous bed: the dead man (see Figure 2). The melt flow through the dead man can affect substantially the hearth lining life, the furnace productivity and product (i.e. hot metal) quality. Physical characteristics like porosity and particle size distribution of the porous coke bed play a critical role. Because of the distributed nature of the coke properties, the bed packing structure and porosity will not be constant.

Jan 1, 2003

By Hans-Åke Häggblad, Bertil I. Pålsson, Jan Stener, Kent Tano, Andreas Berggren, Pär Jonsén

Numerical modelling of grinding in tumbling mills is traditionally done with the discrete element method (DEM). The grinding balls are then represented by DEM particles and the mill structure is considered rigid. To include more physical phenomena several numerical methods can be combined. One important improvement is to include the mill structure response, using the finite element method (FEM). The interaction between charge and lining can then be studied in detail. The pulp can also be included using a particle-based continuum method e.g. smoothed particle method (SPH). The strength of SPH lies in modelling of free surface flows and very large deformations and it is suited to model simultaneous fluid and granular flow. Still, the coarse particles (grinding balls) in the charge are suitable to be model using DEM. Each of these methods has their strength and weaknesses, but combined they can successfully mimic the main features of the charge movement. With these numerical tools the complex interaction between the different components of the grinding process; pulp, charge, lining and the mechanical behaviour of the mill, can be studied together. This work will present novel numerical approaches to model, simulate and validate charge behaviour in tumbling mills. These numerical models give possibilities to better understand the physical and mechanical behaviour of particulate material systems during grinding in a tumbling mill. This is important in order to develop and optimise future high-capacity grinding circuits and save energy.

Jan 1, 2014

By V. G. Minenko, V. A. Chanturiya, A. L. Samusev

Eudialyte is one of perspective resources of zirconium and other rare earth elements (REEs). Large reserves of eudialyte concentrated in the Murmansk region of the Russian Federation. Usually, technologies of REE treatment include the decomposition of eudialyte concentrate in different acidic, extraction and utilization of all components. The main problems in the leaching of eudialyte include are: the formation of an unfiltered silicon-containing gel; low recovery of REE; difficulty extraction of metals from the productive solution; high aggressiveness of the reagents. One of the promising trends of intensification of the processing of hard-to-degrease rare metal raw materials is the use of energy methods for affecting mineral suspensions. These methods make it possible to increase the efficiency of break up fine-dispersed mineral complexes and extracting micro- and nanoparticles of a valuable component in subsequent deep processing. The purpose of this work is to investigate the effect of energy impacts on the nitric acid leaching of eudialyte concentrate. Experimental studies were carried out in a developed laboratory facility that makes it possible to evaluate the effect of electrochemical, ultrasonic and combined effects on the leaching of zirconium and REE from eudialyte concentrate. The studies carried out on the samples of eudialyte concentrate with the size class of -0.315 + 0.063 mm showed that the use of electrochemical and acoustic effects increases the extraction of ZrO2 in the production solution in 1.6 - 2.5 times, REE in 1.3 - 2.2 times, respectively. An analysis of the microstructure and phase composition of the surface of the eudialyte concentrate showed that the intensification of the leaching process is due to surface cleaning from the silicon-containing gel, as well as the opening of capillary channels and microcracks, which accelerates mass-transfer processes. The results obtained open wide opportunities for creation of modern and effective technology of processing of eudialyte concentrate, producing high-quality zirconium products and REE.

Jan 1, 2018

By M. Nonaka

An attempt to produce fuel from biomass waste by hydrothermal treatment has been made with expectation to effectively utilize a renewable source of energy and an unexploited energy resource. In this paper, we have used empty fruit bunch (EFB) that is a residue after recovery of crude palm oil from palm oil trees in a plantation in a tropic country. A hydrothermal treatment was conducted using a 500 mL autoclave, with alkali (K2CO3) catalyst. EFB was decomposed more by alkali catalyst of lower alkali content and rather polymerized in higher catalytic region. The functional group composition of the solid phase oil is similar independent of alkali content, however its burning characteristic became more incombustible with increasing alkali content.

Jan 1, 2014

By P. Harris, D Bradshaw

"Comparison of the two most commonly used classes of depressant in the South African platinum industry is complicated by the fact that these polymers induce different effects on the surfaces onto which they adsorb. The use of carboxymethyl cellulose (CMC), which is ionically charged in solution, can lead to increased particle dispersion in addition to the effect of reduced surface hydrophobicity (depression). Guar is typically only slightly charged in solution. Comparison of these two depressants is complicated since it is uncertain whether differences in their action is a result of either depression of dispersion effects.This work investigates the role of dispersion independently to that of depression in the batch flotation of a platinum bearing ore. An inorganic dispersant, sodium hexametaphosphate (NaHMP) was added in parallel to the uncharged guar depressant to simulate the action of depressants with varying degrees of dispersion. By distinguishing between the material recovered by entrainment and the floatable gangue and by including the effects of froth stability it was possible to decouple the effects of dispersion and depression.The results show that both dispersion and depression led to increased grade of the sulphide minerals. Depression leads to a decreased recovery of floatable gangue minerals. Dispersion leads to an increased recovery rate of these minerals and an accompanying decrease in froth stability."

Jan 1, 2003