Search Documents

Goethite ore are the third most abundant source of iron. The overwhelming part of these ore is represented by low-grade varieties which cannot be used in iron and steel industry without preliminary beneficiation. Biomass is a renewable solid fuel, which is feasible for the substitution of coke and coal in the manufacturing due to its lower contents of harmful elements and abundant raw material sources. Utilization of biomass in iron ore sintering process as heating agent and reducing agent contributes to energy conservation and emission reduction. The biomass was mixed together with goethite ore for roasting process to investigate the effects of reduction roasting. The results show that the goethite ore is dramatically reduced and magnetized into maghemite by biomass with the biomass dosage less than 20% and the roasting temperature below 650 oC. When the goethite ore roasted with biomass, the magnetization values could be enhanced more than two orders of magnitude, meets the standard of magnetic separation, which could significantly reduce the iron beneficiation cost. Keywords: biomass, goethite, reduction, magnetization, roasting

Sep 1, 2012

By M. Kanuchová, J. Briancin, M. Achimovicová

"Faculty of Mining, Ecology, Process Control and Geotechnology, Technical University, Košice, Slovakia An industrial eccentric vibratory mill was used for direct and short-time mechanochemical reduction of ilmenite concentrate (FeTiO3) and anatase (TiO2) with magnesium metal powder in order to reduce Fe and Ti resp. and hereby to convert them to the more soluble phases suitable for further hydrometallurgical processing. X-ray diffraction analysis of FeTiO3 after 60 min of milling with Mg confirmed the presence of Fe0 and Mg2TiO4 phases and for TiO2 after 180 min of milling the new TiO and MgO phases have appeared. X-ray photoelectron spectroscopy has detected Fe0 (metal) and Mg2+ species which are corresponding to the product of FeTiO3 mechanochemical reduction. The product of TiO2 mechanochemical reduction has revealed XPS spectral lines corresponding to Ti2+, Ti4+ and Mg2+ species on its surface. Morphology of mechanochemically reduced samples was studied by scanning electron microscopy analysis. Subsequent leaching of mechanochemically reduced FeTiO3 and TiO2 was performed in dilute HCl and H2SO4 at 80oC and compared with mechanically activated samples. The recovery of Ti has reached 100% for FeTiO3 and 79% for TiO2 after 60 min of leaching. Based on this study the flowsheet for possible processing of natural refractory titanium ores patented by author was adapted and documented. INTRODUCTION Ilmenite (FeTiO3), along with rutile (TiO2) represents the most important titanium resource necessary for titanium industry, for production of titanium metal, alloys and pigment grade TiO2 which are becoming more important and versatile for various industries such as an aircraft and aerospace, navy, chemical, automotive, medical and offshore wind industries, for machine and plant engineering and architecture as well, mainly due to high corrosion resistance. Pigment grade TiO2 is utilizing in pigment, plastic, glass, paper and rubber industries (Zhang, 2011). There are obvious research efforts for development of the potential alternatives to the expensive thermo-chemical commercial processes of titanium raw materials processing. Zhang (2011) has summarized conventional thermo- a electrochemical processes which involved a combination of pyrometallurgical, hydrometallurgical and electrometallurgical technologies and highlighted the improved hydrometallurgical routes promising for commercial application in the future. Such improvement could also be mechanical activation of FeTiO3, TiO2 by high-energy milling which causes their structural disordering, the changes of physical and chemical properties, consequently and has a positive effect on the dissolution kinetics (Achimovicová et al., 2014a, 2017, Baláž, 2008). The various types of mills such as a planetary ball mill, a vertical ball mill, a drum mill, an attritor were used for mechanical activation of FeTiO3 as a pretreatment process for subsequent leaching (Achimovicová et al., 2014)."

Jan 1, 2018

By André Mans, Frans B. Waanders

Current losses of Ferrosilicon (Fe-Si), which is used in the dense medium separation (DMS) of iron ore at Kumba Resources, Sishen, South Africa occur due to adhesion to the separation products and also by being present in the effluent stream, due to abrasion. The losses contribute greatly to the running cost of the plant and the purpose of this project was to determine the characteristics of the unused Fe-Si and then to characterise the changes that occur during storage and the use thereof. A Scanning Electron Microscope (SEM) and Mössbauer Spectroscopy (MS) were used to investigate the characteristics of the fresh and used Fe-Si. It was found that the biggest loss of Fe-Si was due to the abrasion of the particles during the DMS process, which resulted in the liberation of Fe and subsequent formation of an oxihydroxide froth. A possible change in magnetic properties was also observed, leading to further losses that could occur during prolonged use of the medium. No clear changes to the Fe-Si occurred during correct storage methods, as was initially thought.

Jan 1, 2003

By T. N. Matveeva, L. B. Lantsova, N. K. Gromova

"Multimetal gold-antimony ores are complexed processing products, since they are characterized by veindisseminatedsulfide mineralization with fine-dispersed submicroscopic gold, low content and uneven distribution ofAu, which is concentrated together with iron sulfides (pyrite, arsenopyrite, pyrrhotite). Such ores are classified asrefractory ones and characterized by low gold recovery rates during cyanation. A particular feature of gold-antimonydeposits is the presence of antimony in industrial concentrations therein, along with gold that significantly increasesthe value of these deposits. The main antimony mineral is antimony sulfide - antimonite (stibnite). Gold-antimonyores undergo flotation concentration with producing collective gold-containing concentrates or gold sulfide andantimony concentrates. The purpose of the work is an experimental study of the flotation separation mechanism ofsulfide minerals of copper, antimony and arsenic using tannin-containing modifiers during processing of multimetalgold-bearing ores. During the research it was established that for the selective separation of antimony and arsenicsulfide minerals into concentrates of different kinds, it is possible to use vegetable reagents capable to be selectivelyadsorbed on the arsenopyrite surface. Using the laser KEYENCE VK-9700 and electronic LEO-1420 VP INCA-350microscopy methods, it has been established that the film of a vegetable modifier was not washed off with water andfixed firmly enough on the surface of the polished sections of arsenopyrite. In the X-ray spectrum there are C and Obands related to the reagent structure. The vegetative reagent is fixed both on the pre-adsorbed phase of the collectorand on the areas free from the collector. On the polished sections of antimonite before and after a contact with thetannin solution, only partial adsorbed tannin phases are detected, which disappear as a result of subsequent washingwith water.The reported study was funded by RFBR according to the research project ? 16-05-00646 ?."

Jan 1, 2018

By Wantae Kim, Hoon Lee, Kwanho Kim, Sangbae Kim

Mechanochemical activation of starting minerals and their effect on the solid-phase synthesis and properties of ceramics with lower thermal expansion coefficient was examined. The mineral mixture, pyrophyllite-gibbsite-lithium carbonate, was prepared for the synthesis of ?-eucryptite (Li2O•Al2O3•2SiO2). Dry grinding using a planetary ball mill promoted the amorphization of the starting mixtures. XRD and FT-IR results showed that the crystallization of the target materials occurred from the ground mixtures by calcination. The crystallization of them increased with increment of grinding time and calcination temperature. In the synthesis, the trace of undesired phases such as quartz and cristobalite once formed during calcination at the temperature range from 750 to 850 °C almost disappeared and monophase ?-eucryptite was formed in the ground mixture at 950 °C. The lowest liner thermal expansion coefficient (TEC) of ?-eucryptite prepared was -2.5x10-6•°C-1. The thermal expansion behavior characteristics of the calcined

Jan 1, 2014

By Christopher Robben, Alexander Mosser

"X-ray transmission (XRT) sorting has been introduced into the minerals industry in 2006 and has found various applications in diamonds, industrial minerals and metal ore processing since. The technology offers planar projections of the atomic density of single particles similar to the principle known from airport scanners, but being capable of treating up to 150tph per metre working width. In 2010, a pilot operation using a belt-type sensor-based sorter went into production at the Mittersill mine to treat the fraction 16-28mm. After an optimisation phase, the results were superseding expectations and therefore in 2012 a bigger production plant was set up. Two XRT-based sorters are parallel in operation since. One is treating the fine fraction 16-30mm while the other one is treating the coarser fraction 30-60mm after the secondary crushing stage. The XRT sorters are operated with the objective to reject barren waste before it enters the mill and flotation plant. 105,000tpa of waste material are rejected per year and can be sold as aggregate for road construction. This means that about 22% of the run-of-mine ore are rejected at an early stage with a waste reject grade lower than 0.03wt%WO3. The installation has not only led to lower specific operating costs but also led to reduced tailings disposal in an environmentally sensitive area. This allows the mine to reduce its headgrade which allows for a longer mine life. Alternatively it is possible to produce more tungsten concentrate, which is delivered to the smelter. This article will introduce the technological principle of XRT-based sorting and will discuss the flow-sheet of the Mittersill mine. Experiences that have led to the current plant design are described as well as the impact it has on the operation."

Jan 1, 2014

By A. V. Kozub, D. O. Sharkovsky, R. I. Ismagilov

"Due to complex mineral composition and fine ingrained nature concentration of iron ores deposited in Mikhailovskoye mine field requires application of wet magnetic separation to produce 65–66% Fetotal and 8.2–8.6 %SiO2, concentrate with 90–94% of material being –0.044micron grain size. Higher specific consumption of ROM, increase of production costs with concurrent reduction of output - those are inevitable side effects of desired concentrate grade improvement. Large-scale complex analysis and surveys have been carried out aimed at concentrate grade improvement with concurrent output increase. Classification of feed in hydraulic cyclones (hereinafter referred to as hydrocyclones) has been the bottleneck for improvement of processing throughput and concentrate output. Hydrocyclone classification efficiency is 50-60% and further improvement is practically impossible. Actual circulating load may achieve as much as 500-600% while the optimal rate is 200-250%. Application of wet fine screening has been considered to improve iron ore concentrate grade. Objective of this work is to design processing flow diagram for unoxidized ferruginous quartzites with implementation of wet fine screening. Large-scale tests have been run in Crushing and Concentrating Plant with application of wet fine screening stage. These tests included application of wet fine screening in 2 and 3 stages of classification to separate desired grain sized material; replacement of hydrocyclone classification with fine screening; application of fine screening as additional stages to concentration process and screening of final concentrate. Testing Methods. EXPERIMENTS AS WELL AS THEORETICAL RESEARCH HAVE BEEN APPLIED FOR THE PURPOSES OF THIS WORK; INCLUDING MAGNETIC, GRAIN-SIZE AND CHEMICAL ANALYSIS OF CONCENTRATION PRODUCTS. MODERN ANALYTICAL DATABASE HAS BEEN APPLIED TO STUDY WET FINE SCREENING FEATURES, MINERAL AND PHYSICAL COMPOSITION OF CONCENTRATION PRODUCTS. Work Results: - analysis of wet fine screening application for iron ore concentration. - technological solutions enabling to improve slurry classification of fine ingrained low magnetic iron ore have been developed. - effective process flow diagram including fine screening has been designed based on the feasible and reasonable arrangement solutions."

Jan 1, 2018

By Vladimir Vigdergauz

"Electrochemical studies of metal sulfides in connection with their floatability are discussed. According Frumkin, sorption of electroneutral organic substances has a maximum near the potential of zero charge. This idea initiated attempts of application of electrochemical methods for the controlling of organic collector sorption and mineral flotation. The lecture reviews results of electrochemical studies of the processes taking place during sulfide flotation: redox-state of mineral surfaces and xanthate solutions, xanthate sorption and hydrophobic layer composition, surface wettability and flotation recovery of sulfide minerals. Redox-transitions of minerals, transport of ions and charging of mineral surfaces, electroreduction of dissolved oxygen and accompanying processes of oxidation of minerals and reagents-collectors, - all these matters became the subjects of detailed research. Cyclic voltammetry, rotating disk electrodes, spectro-electrochemical techniques and other modern experimental methods now routinely accompany studies of mineral processing. Relatively new electroanalytical techniques like the voltammetry of mineral particles immobilised on electrodes using polymeric binders have become extremely useful for studying weakly conductive minerals and dispersed flotation products. Full discussion of electrochemical studies of metal sulfides in relation to mineral processing must include bioelectrochemistry and electrocatalysis which open exceptional possibilities for selective leaching of gold and non-ferrous metals. At this time, the paper focuses on the sulfide flotation as a potential-dependent process; the problem of oxygen and its influence on the sulfide flotation; the electrochemical aspects of xanthate oxidation and sorption; theory of suspended electrodes as applied to the mineral slurries and experimental study of the effect of electrochemical pretreatment of flotation pulps."

Jan 1, 2014

By Michel Brissette, Shaheer Sanuri, Veroljub Mihajlovic

"The main purpose of geometallurgy is to improve the mine planning by mapping hardness and throughput into the mine block model using geostatistics to eliminate the large production fluctuations caused by the ore hardness variability coming from different parts of the pit. However, not all grinding testwork available commercially can be applied to geometallurgy because of large amount of sample required and the associated cost per test. Geometallurgy is now being used in designing grinding mill but as the mining project progress, the accuracy of engineering must improve from 30-35% during the scoping study to 10-15% at the bankable feasibility stage and less than 5% for Engineering Procurement and Construction Management. For SAG milling, the SAG Variability Test (SVT) is an abbreviated version of the standard SAGDesign test developed for this geometallurgical need. The same amount of ore than the original test is ground for three cycles into an open batch SAG test and then the SAG pinion energy is predicted to the standard end point of 80% passing 1.7 mm. For ball milling, a Bond Variability Test (BVT) was also developed using the SAG ground ore from the SVT. The Bond ball mill grindability (Gpb), corresponding to the average of the net grams per revolution from the last three cycles of the Bond test, is also predicted from the third cycle. The relative error for both the predicted SAG ore hardness (WSVT) and Bond Work Index on SAG Variability ground ore (Sv-BVI), in kWh/t, averaged 5.5% and 3.8% respectively compared to the SAGDesign testwork values and are within 7% and 10% respectively from plant benchmark and within 7% from the samples sent to all partner laboratories. Both tests can be continued to measure the true hardness necessary for mill sizing. This article discusses the development of these two new tests, SVT and BVT, their potential use and accuracies in any geometallurgical program."

Jan 1, 2014

By Seher Ata

This paper is concerned with the coalescence behaviour of two bubbles in dilute solutions of cetyltrimethylammonium bromide, methyl isobutyl carbonil and triton x-100. Two bubbles were produced at the tips of adjacent capillaries and the time elapsed between the first contact of the bubbles and film rupture was determined by means of a high speed camera. It was found that the amount of surfactant required to stabilise the bubbles increased in order of CTAB>TX-100>MIBC. The probability of coalescence decreased sharply with increasing surfactant concentration in CTAB and TX-100 solutions while with MIBC each bubble pairs resulted in coalescence, giving hundred per-cent coalescence probability.

Jan 1, 2014

By Masanori Mori, Hajime Miki, Osamu Ichikawa, Tsuyoshi Hirajima, Mitsuru Sawada, Keiko Sasaki

For pretreatment of selective flotation, surface oxidation of chalcopyrite and molybdenite was applied by oxygen plasma then the minerals were washed by solution at pH 9 with oxygen bubbling. Surface characteristics of these minerals were investigated with AFM, XPS, zeta potential and contact angle measurements. Contact angle of chalcopyrite and molybdenite decreased a lot by plasma treatment. When they were washed with pH 9 solution with oxygen bubbling, contact angle of molybdenite increased whereas chalcopyrite one kept low. Adhesion force measurements indicated similar behavior. Result of flotation experiments indicated low recovery of both chalcopyrite and molybdenite after plasma treatment and only molybdenite recovery became higher after washing. Selective flotation of chalcopyrite and molybdenite could be achieved with this process. Possible mechanism of selective flotation was proposed from the results of XPS, AFM, etc.

Jan 1, 2014

By James A. Finch, Xiangzhou Ding, Yue Hua Tan

"The Jameson Cell is one of the choices of flotation machine in coal, base metal processing and other specialist applications. This paper determines the effect on vacuum pressure and bubble size of two design variables, orifice size and downcomer length, and the operating variable air-to-water (AWR) ratio. The main findings are: orifice size and downcomer length impact the vacuum but have limited effect on bubble size; AWR < 1 favours high vacuum, conditions are identified where vacuum is maintained at AWR > 1, and water flowrate has slightly greater impact on bubble size than air flowrate.INTRODUCTIONFroth flotation, the most common technique for mineral separation, has been in use for over a century. The process takes advantage of the difference in wettability of mineral surfaces to achieve the separation of valuable minerals from non-valuable minerals, or gangue. Numerous flotation machines have been invented and patented over the years. The Jameson Cell, invented by Professor Graeme Jameson in the late 1980s, is one successful example. First trialed at Mount Isa Mines (Queensland, Australia), Jameson Cells have been installed at operations around the world for the recovery of fine coal (Mohanty and Honakeri, 1999; Cowburn et al., 2006; Hacifazlioglu and Toroglu, 2007; Uçurum 2009), minerals of copper (Farr 1992; Atkinson et al., 1993; Harbort et al., 1997), lead/zinc (Rohner, 1993; Munro, 2003) and gold (Bennett et al., 2012; Lauder et al., 2003), and in water treatment (Yan and Jameson, 2004), solvent extraction de-oiling (Miller and Readett, 1992; Miller et al., 1997; Harbort et al., 2003; Young et al., 2006), oil sands processing (Neiman et al., 2012), and various food industries (Brenneman, 2014). One of the largest units is the 650 cm diameter separation tank with 24 downcomers installed in an Anglo American operation (Osborne and Euston, 2015). Scale up is relatively straightforward: to increase capacity the number of downcomers is increased with corresponding increase in size of separation tank.The Jameson Cell comprises two main parts: a vertical tube (downcomer) which provides self-aspiration and intense bubble-particles contact, and a (separation) tank where particle-bubble aggregates disengage from the pulp. The intense bubble/slurry mixing in the downcomer with air holdups reaching 60% (Marchese et al., 1992) accelerates particle collection enabling the greatly reduced cell volume compared with mechanical flotation cells and columns. The disengagement of the particle-loaded bubbles from the slurry in the separation tank is usually aided by addition of washwater."

Jan 1, 2018

By N. I. Tyushkova

On the basis of detailed studying of mineral structure of ore and treatment products it is established that the given ore refers to oxidized Pb-Zn vein-disseminated ores. Technological special features of the basic ore minerals and the reasons causing their obstinateness that is defined by following features are revealed, presence at dominating quantity difficult to float lead minerals: mimetesite (9.67%), green lead ore(0.48%); non float: bindheimite (2.16%) and plumbojarosite (0.36%) and high assay of oxides and hydrous ferric oxides; also thin, emulsive and submicroscopic segregations of the defined minerals in swamp ore. As a result of researches the scheme of gravitational-flotation treatment was conducted in semi-industrial scale. It allows to receive two concentrates from ore: a lead gravitational concentrate of mark ??-4 with the assay of 55.5 % of Pb and 0.77 % of Zn; and a Pb concentrate of mark ??-7 with assay of Pb of 40.97 % and Zn of 1.39 %. The total assay of Pb in concentrates makes 81 %. The efficiency offered by gravitational-flotation schemes is defined by possibility for recovery of big impregnated lead minerals under gravitation. The use of this method of gravitation has allowed to recover such mineral as beudantide and to exclude irrevocable losses of lead in tails which are connected with this mineral. Scientific value of the presented researches is connected with the fact the problem of extraction of the oxidized minerals of Bb and Zn is rather difficult and insufficiently studied. Keywords: flotation, oxidized forms of Pb and Zn

Sep 1, 2012

By Rolf Lauten, Yongjun Peng, Yufan Mu

"Biopolymers, produced from cellulosic biomass, have promising prospects of application as depressants in mineral processing. In this study, three different types of biopolymers (i.e., DP-1775, DP-1777 and DP-1778) were used to study the effect of polymer structure on flotation of un-activated pyrite, copper activated pyrite and chalcopyrite. It was found that the depressing effect of DP-1775 and DP-1778 was much stronger than that of DP-1777, and pyrite was depressed to a greater content than chalcopyrite with the same biopolymer at the same dosage. The biopolymer concentration played a vital role in determining the degree of depression. For each biopolymer, the higher the concentration, the greater the minerals were depressed. The mechanism underpinning the depressing effect of these biopolymers was explored in this paper. The concentration of biopolymers could determine the properties of the adsorption layer and the confirmation of biopolymer chains on mineral surfaces. The biopolymer molecules may aggregate when polymer concentration was over a critical value. Molecular weight and functional groups of biopolymers were the key factors characterizing the depressing capability of different biopolymers. Differences between the tested biopolymers and features of the adsorbed layer might account for the observed trends in ability to depress pyrite and chalcopyrite flotation. The greater depressing effect of biopolymers on pyrite over chalcopyrite might result from the preferential adsorption of biopolymers on pyrite over chalcopyrite."

Jan 1, 2014

By Achilles Dutra, Everton Santos, José Oliveira

The beneficiation of phosphate ores by froth flotation is the most efficient process used to separate apatite from gangue minerals like calcite, dolomite and quartz. However, the similarity of surface properties between apatite and calcite generally lead to non-selective adsorption of reagents, rendering the selective separation of these minerals a worldwide problem. The phosphate deposit of Itataia, State of Ceará, Brazil, studied in the present work, presents a complex mineralogical composition having uranium associated with the apatite mineral. The main gangue minerals are calcite and quartz. The bulk flotation of apatite and calcite with anionic collectors in an alkaline medium followed by the selective flotation of calcite at pH 5.5 using phosphoric acid as well as citric acid as depressant have been suggested for this ore. This paper presents the results of contact angle measurements obtained using jojoba oil, a natural reagent composed mainly of gadoleic acid (C20:1) and long-chain fatty alcohols (eicosenol and docosenol), as an alternative collector for the selective separation of apatite and calcite minerals. The hydrophobicity studies were carried out using a computer controlled contact angle goniometer. Additionally, the collector adsorption was evaluated via electrophoretic mobility and FTIR measurements. The results indicated that a high selectivity can be obtained by using jojoba oil as collector in a slightly acid pH range, without the use of depressant. The best results were achieved with a jojoba oil concentration of 200 mg.L-1 at pH 6.5, where the apatite was fully hydrophilic and calcite showed a high hydrophobicity (? > 60 º).

Jan 1, 2014

By Seungwoo Park, Gaurav Soni, Roe-Hoan Yoon, Hyunsun Do, Kaiwu Huang

In a flotation froth (and foam), air bubbles become larger due to coalescence, causing bubble size to increase, bubble surface area to decrease, and hence casing less hydrophobic particles to drop off to the pulp phase below. Thus, bubble coarsening provides an important mechanism by which product grades are increased. On the other hand, excessive bubble coarsening results in low recoveries. In the present work, a model describing the process of bubbles becoming coarser in a foam as they rise to the top by deriving a mathematical relation between the Plateau border area, which controls film drainage rate, and the lamella film thickness, which controls bubble-coalescence rate. The model has been derived by assuming that liquid drainage rate increases due to slip at the air/water interface, and that the critical rupture thickness is determined by the capillary waves created by thermal motion. The model developed in the present work can predict the bubble size ratio between the top and bottom of a foam as functions of aeration rate, foam height, and surface tension (frother dosage). The model predictions are in good agreement with the changes in bubble sizes measured using a high-speed camera.

Jan 1, 2014

By Sanggono Adisasmito

"The quality of the higher education in Indonesia is being improved by implementing a program financed by the World Bank under a project named QUE (Quality for Undergraduate Education). The investments are provided to selected study programs through a competitive selection process. The grant finances staff development, the purchase of equipments, textbooks, consumables, technical assistance, and incentives for outstanding faculties such as teaching grants, project grants, lecture note awards, and educational policy studies. These additional investments are provided to produce chemical engineering graduates that will compete beyond the national market.Chemical Engineering Department of Institut Teknologi Bandung in Indonesia has been selected to receive the QUE grant beginning the year 2000 and ending the year 2004. The department is actively involved in the mineral processing issues, particularly in the aspects of energy supply and the environmental protection. The activities are distributed in different laboratories and areas of expertise, such as: thermodynamics and utility systems, process equipment, chemical reaction and catalysis, microbiology and bioprocess engineering, process control, ceramics, as well as polymer and membrane technology. The main objectives of the QUE project are to improve the undergraduate program in the following aspects: Relevance, Academic atmosphere, Institutional management and commitment, Sustainability, as well as Efficiency and productivity, or abbreviated as RAISE. At the end of every fiscal year, the progress of the program is evaluated to measure the effectiveness of the project.The achievement of the QUE project objectives were assessed using performance indicators developed during the program design. There are six indicators to measure the performance of the individual program of study, such as: (1) Admission Test score, (2) average students' Grade Point Average (GPA), (3) average graduates' length of study, (4) graduates' waiting time before getting first job, (5) Test of English as Foreign Language (TOEFL) score, (6) Graduate Record Examination (GRE) score. Essentially, the RAISE evaluation criteria will be used to perform three main functions, such as (1) to measure the achievement through the six quantitative performance indicators, (2) to support the progress of evaluation and reporting throughout the implementation of the program, (3) to provide a universal framework for qualitative evaluation."

Jan 1, 2003

By F. C. Araújo, T. Tavares, J. Leite

"This work presents the small-scale mining cluster of kaolin in Rio Grande do Norte (RN) and Paraiba (PB), both Brazilian states, including the following information: number of companies, process flowcharts, production numbers, mineralogical (XRD) and chemical (XRF) composition, granulometric distribution (screen and laser granulometer) and image analysis (SEM). Some social indicators in the region of the RN and PB States are presented in association with these data. The number of companies and their flowsheet were obtained through in situ visits and sample collection for technological characterization. The comparative study of the different flowsheets for kaolin production in the world was done using the databases and presenting the state of the art of kaolin processing. The results indicated that the mean feed typically contains 35-39% kaolin with quartz, muscovite and kaolinite as main mineralogical components and SiO2 (65.83%), Al2O3 (21.19%), K2O (3.9%), and Fe2O3 (0,63%) as main chemical constituents. The products of mineral processing are twofold, one between 74 µm and 37 µm, and the other smaller than 37 µm. The wastes of operation had major quantities of kaolin. The average Human Development Index (HDI) of the cluster region is approximately of 0.61, which shows an association between mineral processing plant and social indicators. The kaolin recovery, however, is between 30-55% for the three most common types of flowsheets that are currently used in the small kaolin mining cluster, indicating a need for technological improvement to achieve regional development. These data could be used incrementally to adapt the process plant currently used in the small-scale mining cluster of kaolin."

Jan 1, 2014

By D. Krawczykowski, D. Saramak, T. Gawenda

"Annual world zinc consumption is as high as nearly 14 millions of tonnes. Approximately 50% share of zinc is used for corrosion protection in processes of continuous galvanization and the hot dip processes. In the latter, two zinc containing residues are produced: zinc ash and hard zinc, which constitute around 10% each. Paper concerns the method of possible separation of metallic zinc from the non-metallic zinc compounds from the zinc ashes – the waste product of hot dip galvanization process. The investigative programme covered the comminution tests of the feed (zinc ash) in selected crushers: jaw crusher, roller crusher and impactor. Results of investigations show that application of individual crushing device results in various breakage of the feed sample. Impact force caused the highest increase in finest particles size fractions of the product, while metallic and non-metallic fractions were comminuted differently. The compression force, in turn, caused the selective comminution, i.e. the breakage of metallic zinc was observed in a higher degree. The presented approach appears to be an economical supplementary method of initial recovery of metallic zinc from metallurgical zinc waste. For the high demands for the zinc in the world and the need of corrosion protection, the method presented in the paper helps in more effective zinc recovery and environmental protection.INTRODUCTION AND METHODOLOGY World production of metallic zinc during last decade shows a slight increase and in recent years its consumptions reach 14 millions of tonnes. Figure 1 shows world production of zinc in the time period 2009 – 2016. Main directions of zinc utilization include: - Galvanization - Production of zinc alloys - Brass and bronze production - Semi-manufactures of zinc - Chemicals The major share in global zinc consumption constitute galvanization process (Bright 2007). Two main types of zinc galvanization are: hot-dip galvanizing (HDG) and electro-galvanizing."

Jan 1, 2018

By G. Venkateswara Rao

The jigging of ferrous ore to produce higher-grade products has been practiced for many decades. This is due to easy separation, a beneficial trade- off between operating cost and reduced yield relative to Dense Media Separation (DMS). Jigging becomes prominent for beneficiation of iron ores in the coarser size range. At present drive is towards the use of under bed air pulsed jigs for the beneficiation of ferrous ores. The main advantage is that the under bed air pulsed jigs are capable of generating the large pulse of amplitudes required to fluidize a deep bed of heavy ores particularly lump iron ore up to 40mm size. The major jig parameters effecting the jigging operation are bed height, shape of the pulse, residence time, operating pressure, valve cycle time and water flow rate. With the pulse shape set correctly for optimum stratification rate, even it is still necessary to provide enough residence time, to ensure the difficult material will take time to migrate to the expected layer in the bed. In order to find the Jig Stratification Index (JIS) parameters like bed height, operating pressure, water flow rate, cycle valve time and shape of the pulse were optimized first by conducting various tests. Typical Iron ore samples from Odisha (both lump and fines) were subjected to stratification studies at residence time of 1, 5 and 15 minutes. Jig Stratification Index (JSI) for both lump (0.30) and fines (0.20) were determined by using APIC Jig. The maximum possible JSI was calculated by using heavy liquid separation test (0.42 for lump and 0.24 for fines). It is found that the jig bed JSI is less than the Heavy liquid JSI for both lump and fines. The ratio of Jig bed JSI to the heavy liquid JSI is 0.83 for lump and 0.71 for fines. The JSI and ratio of Jig bed JSI to Heavy liquid JSI are low for fines due to fluid turbulences causing some degree of remixing in the jig bed. The fluid turbulences are more for fines than lump, hence jigging of fines is difficult and challenging. Keywords: sub grade iron ore, gravity separation, jigging, apic jig, stratification, residence time, jig stratification index

Sep 1, 2012