Search Documents

By Hal W. Hunt

Heavier loading and more efficient equipment is helping to keep driven piles competitive in America. Better Knowledge and testing of soils and support materials make it practical to use higher stresses; this is being strongly promoted by those directly concerned with timber, steel and concrete piles. Readily available point protection is increasingly used to assure penetration of piles without damage to full load bearing capability. Fabric drains are being installed with pile equipment to speed consolidation of soils. Sheet pile configuration has changed; production has been reduced largely because of imports. Dynamic checking of representative piles for load carrying capability is replacing conventional load testing of just a pile or two ? at much lower cost.

Jan 1, 1987

By Cristhian C. Mendoza, Renato da Cunha, Bernardo Caicedo, Max Barbosa

"Abstract This paper shows that a raft alone is not sufficiently appropriate to address the uncertainty of underlying soil variability; therefore, a piled raft system is a better option for mitigating such uncertainty. To study the variability of soil, the behavior of the Piled-Raft Foundation was analyzed with a type of self-drilling micropiles: the ""Alluvial Anker"" (common name for this pile type in Brasilia city). These micropiles have been used in the city and have the advantage that the drill pipe also serves as reinforcement. The studied parameters belong to an elastoplastic constitutive model for strain-stress analysis of soil; variability of these parameters can be intrinsic and/or epistemic. Simulations were performed for a hypothetical Piled-Raft Foundation subjected to vertical loading using the random finite element method. The average parameters of the constitutive model were obtained through laboratory tests. The simulations of the load test were compared with results of a real scale experimental test conducted exclusively for this work in the field. It is analyzed the relative importance of the variability of some geomechanical parameters and their variation with depth is considered. In addition, it is discussed a comparison between the uncertainty of the geomechanical parameters and the uncertainty of the results of the vertical loading test. Finally, this paper shows that a decrease of the safety factor may occur when taking into account the variability of the parameters.IntroductionBrasilia is located in a highly weathered residual tropical soil (lateritic & latossol on pedogenetic concepts). This soil presents high content of alumina and iron due to the lixiviation process of the upper layers. As a consequence, the cemented structure is highly unstable and it can generate strong changes of volume (i.e. collapse) due to changes in both moisture and state of stresses. Therefore, a greater understanding of the construction of Piled-Raft Foundation systems on this particular soil conditions is needed – especially because it covers more than 80% of the surface area of the Brazilian Federal District.Thereafter, this work investigates the influence of the variability of the soil parameters over the uncertainty of the Piled-Raft Foundation design. The studied parameters belong to an elastoplastic constitutive model for strain-stress analysis of soils. The simulations were performed for two hypothetical Piled-Raft Foundations subjected to vertical loading by using the stochastic finite element method. The results were compared to real load tests in Piled-Rafts with “Alluvial Anker” pile types."

Jan 1, 2014

By Christopher J. Pacitto

This paper presents a case history of an engineered, monitored, and tested program that provided an effective and satisfactory basis for the completion of pile foundations for Twin Dolphins 1 at La Peninsula Condominiums located in the Isles of Capri in southwest Florida, U.S.A. An 8-story building (withl-story parking underneath) along with recreational facilities (such as a swimming pool and tennis courts) had been planned for final construction. Following an evaluation of various foundation alternatives, a precast prestressed concrete (PPC) pile-supported system was selected. The building foundations were designed for pile capacities of 445kN (50 tons) and 890kN (100 tons) in compression and 133kN (15 tons) in uplift. A test pile program was performed to provide site-specific pile driving data, verify design assumptions, determine production pile lengths, and evaluate pile driving criteria. A total of 24, 356 mm (14-in.) square, 19.8 m (65 ft) PPC concrete piles were driven and dynamically load tested utilizing a Pile Driving Analyzer (PDA) within the building limits. Dynamic monitoring during probe pile installation and restriking was performed to estimate the ultimate capacity of the piles and to evaluate driving stresses during installation. CAPWAP analyses were preformed on PDA data to better estimate pile capacity, resistance distribution, and predict pile freeze (increase in pile resistance with time) and thus optimized the production pile lengths. Upon completion of probe pile installation, 12 of the probe piles were tested using the Pile Echo Tester (PET) function of the Pile Integrity Sonic Analyzer (PISA). PET testing was performed to evaluate the integrity of piles which had exhibited high driving stresses during PDA testing. Information gathered during the probe pile driving program was effectively utilized as part of the overall quality control program to install a total of 539 PPC piles (including 24 probe piles) within the building limits at the project site to depths ranging from 9.1 to 19.8 m (30 to 65 ft) below the existing ground elevation as part of the foundation support system. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the CAPWAP analysis for probe piles. Use of geotechnical instrumentation and PDA assisted technology enabled each foundation support element to be constructed to its optimum capacity and at optimum cost. Furthermore, by using PDA the consultant was able to quantify a difficult to measure geotechnical phenomenon termed "pile freeze" which eliminated costly overdriving and unnecessary splicing of piles.

Jan 1, 2002

By Mark H. Balfe

Over the last decade, Fenway Park has undergone annual improvements to modernize the facility for players and fans. These renovations include the Monster Seats, the Right Field Roof expansion, a new pavilion behind home plate, expansion of the Red Sox clubhouse, additional roof seating, and concourse improvements. Retrofitting the historic ballpark to bring it up to current standards required installation of foundations to support the new structural loads for each of the alteration projects. This required evaluation of existing conditions, and in many cases augmentation of the foundations at existing columns to accommodate the structural changes to the park. New foundations, generally consisting of drilled-in micropiles, were installed in numerous configurations and conditions. Since 2003, a total of 215 drilled-in micropiles have been installed to augment various columns around the park. The micropiles range in capacity between 40 and 70 tons and are installed through Fill and Organic Soils and embedded into the dense Glaciofluvial Sand and Gravel layer. Issues and learning related to the foundation augmentation include schedule constraints (work is typically conducted during the off-season and schedule is very aggressive), encountering old/abandoned utilities or foundations, ventilation of equipment, and management of spoils during micropile installation.

Jan 1, 2011

By George J. Tamara

The urban environment presents special challenges for the design and construction of earth retention systems. Complications arising from difficult subsurface conditions are compounded by the presence of urban infrastructure and existing and prior construction. The proximity of adjacent structures as well as intense prior use can cause special concerns including the potential for archeological artifacts or contaminated ground or ground water. Utilities and structures may be particularly vulnerable to the effects of ground movement, dewatering and vibrations. Difficulty of access, congestion and limited work areas may severely restrict means and methods of construction. Dewatering may be limited or prohibited because of concerns for disposal of clean or contaminated water, depletion of aquifers, drawing of contaminants to the site or dewatering induced settlements.

Jan 1, 2003

By Y. K. Wong

This paper describes in detail various problems concerning the construction of a pile-raft foundation supporting a 42-storey tower block. The subsurface generally consists of highly weathered sedimentary rock. A comprehensive instrumentation program is implemented to monitor the behaviour of the foundation system throughout the construction period of the superstructure. Instrumentation observations are highlighted in the second half of the paper.

Jan 1, 2010

By Lori A. Simpson

Mission Bay is a 300-acre reclaimed site in San Francisco, California, that is currently being redeveloped. Plans include new neighborhoods, parks, a new University of California, San Francisco, research and development campus, a biotechnology campus, and commercial office buildings. New infrastructure is being constructed throughout the site, consisting of utilities, pump stations, and roadways. Previously, Mission Bay was a part of the San Francisco Bay. Reclamation of the shallow bay coincided with the booming development in San Francisco in the 1880s and continued through 1920. Subsurface conditions are extremely variable throughout the site. The stratigraphy generally consists of 5 to 45 feet of fill, up to 140 feet of weak, compressible clay (?Bay Mud?), dense sand, stiff clay, and bedrock of the Franciscan Complex that has been encountered 5 to 210 feet below the ground surface (bgs). Geotechnical issues related to these subsurface conditions include liquefaction, lateral spreading, settlement, and adequate foundation support. This paper presents case studies of the geotechnical aspects of design and construction of several buildings in Mission Bay, highlighting the similarities and variability in the subsurface conditions and the different conclusions and solutions developed for each project. The case studies will include: 1) a building supported on steel H-piles where the depth to bearing varies from about 70 feet bgs in one half of the site to 165 feet bgs in the other half; 2) a building supported on precast, prestressed, concrete piles bearing in a thick, very dense sand layer; 3) a building with over 100 feet of Bay Mud supported on 120- to 180-foot-long PCPS concrete piles driven to bedrock adjacent to buildings supported on steel H-piles driven to bedrock; and 4) sites where auger pressure grouted displacement piles (APGD) and Tubex piles were installed. Case studies will include results of pile driving analyzer (PDA) testing and static pile loads tests, where performed.

Jan 1, 2006

By A. R. Katti

The stone columns are widely used in the improving the bearing capacity of weak soils mostly for supporting flexible foundation systems. The load carrying capacity of a stone column is complex in nature. The load capacity is derived from the lateral stresses acting on the stone column due to load transmitted from the flexible structure due to deformation to soil mass and which in turn transmits lateral pressure in s3 direction. The load capacity is also function of the f value of the stone column, cohesion of the surrounding soil, K0 and Gb2 of surround­ing soil including passive resistance developed to lateral deformation of the stone column. The assessment of axial and radial deformation is much more complex. Recently Katti et.al. have developed a method based on a granular heap approach and computed with equivalent fe. which combines the effect of s3a and equivalent volume concept to estimate radial and axial strains. In this paper an attempt is made to put forward guidelines for design of stone column accounting for both stability with respect to shear and also with respect to settlement. The estimate of settlement are based on the internal properties of stone column and surrounding soil. It is considered thus the settlements computed are more realistic.

Jan 1, 1996

By David E. Thompson

This paper describes the full-scale field load testing of three deep foundation units using the Osterberg Load Cell. The load tests were completed on three separate projects, two in Massachusetts and one in New York. The Massachusetts projects involved the load testing of two 18-inch O.D. concrete-filled steel pipe piles over water for railroad bridge reconstruction projects in Revere and Saugus/Lynn. The New York project involved the load testing of a 24-inch diameter drilled shaft socketed into sandstone on land for a building foundation in Rochester. The 18-inch O.D. piles were loaded to failure at jack pressures of 142 to 215 tons. The drilled shaft was loaded to failure at jack pressures of approximately 450 tons. The loading testing procedure is described and the results of the three tests are presented. The advantages and disadvantages of the Osterberg load cell for load testing of deep foundations are discussed.

Jan 1, 1989

By Stefano Trevisani

Abstract The FIEC Sustainability Vision states that “risks should be identified and allocated in a fair manner across the project team from the early stages of the design phase. A partnering approach, where objectives and timescales are agreed in advance together with all relevant partners in the value chain, offers a useful solution to improve on site efficiency and reduce disputes”. An alliance or collaborative form of contract involving all parties is the best way to ensure fair contract conditions and proper risk allocation in construction projects. Collaborative contracts are particularly useful where there is uncertainty or undefined information or in the event of technical difficulties and other risks difficult to allocate among the parties involved in the project. Owners sometimes require even special output in terms of innovative technical solutions or special performance. In addition, this particular form of cooperation has been construed and developed with the intention of avoiding and mitigating another great risk associated with the construction industry (especially in complex projects): disputes and conflicts, which are often a major cause of delays, increased costs, loss of reputation and opportunities. In contrast, Alliances are a way to increase and strengthen business relationships, technical and economic innovation and effectiveness, in a worldwide global context where the waste of resources must be avoided in order to guarantee future recovery and growth. Of course, the total cost of a project is usually a key factor and the main driver for the Owner and the Contractors in deciding the type of relationship between them as well as the subsequent relationship with subcontractors and lower-tiers. This paper and presentation, will explain the main features and the principle benefits that the use of collaborative contracts can bring to all parties involved in the construction project, including the sustainable financial return that might be achieved if costly and time consuming disputes can be avoided.

Jan 1, 2014

Jan 1, 1984

By David A. Hart, Barry P. Osborn, Richard J. Totty, Ana T. Carvalho, Max B. Elliott

This paper addresses the experience designing and installing bored piles for the King’s Cross area. This includes continuous flight auger and rotary bored piles, with a range of diameters between 600 mm and 1200 mm, reaching a maximum depth of 56 m below ground level. Existing Network Rail Thameslink twin bored running tunnels are located directly beneath the subject plots. These tunnels have an external diameter of 6.6 m and the crowns of the tunnels are very shallow, in some cases just 10 m below the existing ground level. Some plots needed piles to be installed in close proximity to the tunnels, which required additional control measures and contingency plans. Pile verticality was monitored as the tip of each pile advanced and in-tunnel monitoring readings were verified and are presented. Lessons learned from designing, installing and testing the piles and monitoring the tunnels are addressed in this paper.

May 1, 2022

By David G. Winter

The Olive 8 excavation site in Seattle was surrounded on three sides by conditions requiring innovation, careful modeling, and extensive instrumentation to support use of a first-of-its-kind shoring system. The solution combined heavy soldier piles, long and steeply angled tieback anchors, and tightly spaced soil nails to support surcharge loads from a 33-story adjacent tower separated by a narrow alley housing critical utility lines. Land restrictions on two other sides of the site also required innovative applications of traditional methods. The Olive 8 project has won three state and local awards for innovation and has been reported on in Engineering News-Record and has been the subject of two feature articles in the Seattle Daily Journal of Commerce. This paper presents the conditions and site challenges, reviews the design analysis, discusses the shoring performance, and looks at other potential applications.

Jan 1, 2009

By Mohammadreza Khanmohammadi, Kazem Fakharian

"AbstractIn driven piles, the gradual dissipation of excess pore water pressure and consequently the soil setup significantly contribute to increasing the pile capacity with time. The question is risen that how the scale differences affect the stress state variations around the pile shaft and at the pile tip? Would the CPT predictions better correlate with End-Of-Drive (EOD) or Beginning of Restrike (BOR) conditions? On the other hand, are the proposed a and ß parameters for clayey soils mostly predicting the EOD or BOR situation? The main objective of this paper is to back calculate the a and ß parameters from CPT profiles, pile Dynamic Load Tests (DLT) at the EOD and BOR as well as Static Load Tests (SLT) and evaluate how they compare with those suggested in literature. Four precast 400 mm square concrete piles driven in North Azadegan Oilfield in Khuzestan Province were selected for the comparisons. CPT test results were available from the extensive geotechnical investigation at the study site. DLT tests using PDA were carried out at EOD, 1 day and 14-day BOR on all the 4 piles. All the piles were SLT tested as well. The UniCone software was used to estimate the tip and shaft resistances using 4 methods including the Dutch, Eslami & Fellenius, LCPC and Schmertmann. The results indicate that the a-method based on the proposed values in literature has predicted a shaft capacity of 90% of the 14-day BOR. This is while the ß-method has predicted a shaft capacity equivalent to 1-day BOR results only. Therefore, both methods have under-predicted the shaft capacities compared to real capacities measured after the significant soil setup in the study area. Two of the CPT methods have underestimated, one has overestimated and one has matched the estimated 60-day capacity."

Jan 1, 2014

By S. L. Karunakaran

Selection of an appropriate foundation system requires great skill and ingenuity on the part of the designer. Certain guidelines for choosing between a pile and raft foundation are presented. A number of methods are available for estimating the capacity of piles, giving a wide range of values for the theoretical load carrying capacity. A few aspects to be taken into account while arriving at an appropriate theoretical capacity are discussed. The effect of fluctuation of water table level on the pile capacity and method of accounting for this factor on the pile capacity obtained through initial load test are also discussed. A case study presents a comparison between the estimated values of capacity of piles and the values obtained through the initial load test.

Jan 1, 1996

By Maurizio Siepi

The realisation of most of the civil engineering works is subordinate to the execution of consolidation works, in order to improve the soil physical-mechanics characteristics. The works classifiable with the term "Soil Improvement" can be realised using several technologies, among which the Deep Mixing Method is distinguished for his remarkable flexibility and productivity characteristics. The Deep Mixing Method is a process whereby a rotary drilling machine mechanically drills a constant diameter hole while cement slurry is injected into the soil at high pressure. The process combines state of the art construction techniques merging mechanical and hydraulic mixing energies at the tool bit. The result is a soil-cement column of engineered strength, consistency and dimension. Whereby the soil cement column formation process is controlled by a computerised device, the result is a speedy installation, thorough mixing, and a high degree of control, repeatability and documentation.

Jan 1, 2002

By Lance A. Roberts

Expansive soil formations can be found throughout the United States. When subjected to wetting, these formations have the potential to swell and exert large uplift forces on buildings and foundations. Lightly loaded structures, such as single family residences founded in areas of expansive soils, can be significantly damaged due to uplift movement from swelling actions. Designing an economical deep foundation that can resist uplift forces is critical to prevent damage to these structures. The current solutions to control uplift due to swelling soils, such as over-excavation and replacement of the expansive material or the use of drilled shafts can be costly. Piles made from recycled polymer materials could provide a solution. Due to a lower coefficient of friction along the interface of the soil-pile interface compared to traditional pile materials, solid recycled plastic piles can allow expansive soils to move nearly independently from the pile when wetted. This results in a much smaller magnitude of uplift force being transferred to the structure, which minimizes the risk of significant structural damage from excessive movements. This paper presents the results of research conducted on the use of recycled plastic piles in an expansive shale environment. The preliminary phase of the project involved the installation of six recycled plastic piles at a test site on the South Dakota School of Mines and Technology campus. Two of the piles were subjected to a full-scale compression load test in order to determine ultimate capacity. The remaining four piles were subjected to long-term monitoring of uplift movement during the course of the project. A concrete anchor was also installed at the test site for uplift monitoring. Data gathered during the field and laboratory testing was utilized in a non-linear soil-structure interaction model to predict the displacement behavior and internal stresses within a plastic pile and concrete anchor subjected to uplift forces from the swelling shale. While more research is needed to further understand the application for recycled plastic piles, the results from this research indicate that their use is a viable alternative for support of lightly loaded structures in expansive soil environments.

Jan 1, 2010

By James A. Mason

The State of California has instrumented numerous buildings, bridges, and dams throughout the state with earthquake recording devices. These accelerometers are strategically placed to measure the response of the structure to a specific seismic event. This comprehensive program enlightens the field of seismic engineering after each earthquake. The Office of Strong Motion Studies, California Strong Motion Instrumentation Program, a sub-branch of the Division of Mines and Geology, provides a professional service unequalled in the world. Within hours of a local earthquake, a preliminary report with the epicenter / hypocenter, structural damage, and time history records are available to all interested parties. The included partial report in the appendix, see section 5.1, is one of the reports that C.S.M.I.P. produced after the Loma Prieta Earthquake of October 17,1989. The diagram on the cover is even of interest. This is a small portion of San Francisco. The values on the diagram are the recorded maximum horizontal ground accelerations at that location in the city. For example, the acceleration at Yerba Buena Island was 0.06g. (The "g" refers to the acceleration of gravity. Thus, a 0.06g acceleration refers to the force, F=m*a, that the structure would experience. For this case, the force would be six percent, 6 % , of the mass of the structure.) Yet, directly on the other side of the Bay Bridge, at Treasure Island, the acceleration was 0.16g. Yerba Buena Island is a natural island composed of hard granular material. Whereas, Treasure Island is a man-made island of imported filled. Here one can see the absorption / transmission difference between hard material, which interact with short seismic wavelengths, and soft cohesive material, which interact with long seismic wavelengths.

Jan 1, 1993

By Jason Weck, Alper Turan, Ali Chehadeh

"Rapid expansion of urban areas dictates the need to expand/rehabilitate the existing buried infrastructure at the same rate. The technical challenges such as variable soil and rock profiles, high groundwater tables and limitations imposed by the built environment combined with present fiscal and schedule limitations necessitates the implementation of fast and cost effective construction methods. Since drilling procedures and equipment allow the construction of overlapped pile systems in almost all subsurface conditions, the secant pile walls have become a cost-effective shoring option for such infrastructure expansion/rehabilitation projects. The secant pile walls constructed in a circular plan layout to form a vertical shaft provide unique advantages since they act as a compression ring. Secant pile walls require stringent drilling tolerances be achieved in order to provide structural support and to work as a compression ring in addition to a groundwater cut-off wall.This paper outlines design methodology, installation procedures and verification techniques used for the secant pile compression ring for the Waterloo Landfill Pumping Station No.2. The secant pile compression ring had a 6m inner diameter with over a 20m wall depth and over 18m excavation depth. The details of subsurface conditions, analytical and numerical methods used in design are presented here. The details of the monitoring system are introduced and results of monitoring are presented and compared with analytically estimated and numerically simulated quantities. The results presented in this study are considered to be of interest to those involved in design and construction of vertical circular shafts."

Jan 1, 2014

By Swaminathan Srinivasan, Jess A. Schroeder

"Landslide activity along U.S. 50 in Cincinnati, Ohio (USA) has caused roadway damage for decades. After a necessary closure of three lanes due to slope movements, emergency stabilization measures were undertaken to protect the roadway by providing a short-term solution necessitated by The Ohio Department of Transportation budget constraints. The landslide shear plane occurred on a sloping bedrock surface as much as 50 feet below grade. Drilled shafts were installed 40 feet downslope of the roadway shoulder and were heavily reinforced across the shear plane but steel reinforcing did not extend the full length of the shafts and was stopped well short of the ground surface. Instrumentation data has been collected for 11 years after construction has shown these “Stub Piers” have provided much more than a short-term solution and have provided an attractive alternate to conventional deep shafts or tieback drilled shaft options.INTRODUCTIONLandslide activity has occurred along U.S. Route 50 in western Cincinnati, Ohio for many decades. The site is located between North Bend and Addyston, Ohio on the right descending (cutting) bank of the Ohio River. Road distress caused by slope movements required periodic repairs over recent decades. Railroad tracks downslope of the roadway also showed signs of horizontal displacement and periodic repair. Visual evidence in 2005 suggested the shear plane extended below the US 50 roadway and extended out into the Ohio River.A weed and brush-covered slope extended down slope from the roadway at about 3H:1V for a vertical distance of about 20 feet. Above US 50, the hillside continued to rise more than 100 feet. There is a railroad right-of-way at the toe of the slope with the Ohio River bank just downslope of the railroad.In 2005, Terracon Consultants was retained by the Ohio Department of Transportation (ODOT) to perform a geotechnical study that included 17 test borings and inclinometer monitoring at 4 locations. Roadway damage was occurring (see Figure 1). After only a few weeks of monitoring, the inclinometer casings sheared off about 50 feet below grade, near the soil / bedrock interface (see Figure 2). Soon after, the roadway distress worsened, causing ODOT to close 3 of the 4 lanes to traffic and reroute traffic onto the remaining single lane and shoulder. Terracon was asked to develop a stabilization design under emergency repair conditions. However, both limited budget and time-related constraints necessitated a direction by ODOT that the solution be at least “pseudo” short-term (3 to 5 years)."

Jan 1, 2017