Search Documents

By J. Wennerstrand

Slender steel piles have found an increased use in Sweden in resent years. These piles are often driven throw soft normally consolidated clay to refusal in till or at the rock surface. In contrast to most other piles the bearing capacity with regard to failure of the shaft is in many cases smaller than the bearing capacity with regard to failure of the soil or rock at the lower end of the pile. Imperfections such as deviations from a straight line of the pile centerline and residual stresses in rolled and welded profiles are important for the capacity of the pile shaft. Even thow the second order moment caused by initial deviations in piles is only half of that in a column with the same slenderness, imperfections can and should be accounted for in much the same way as for columns.

Jan 1, 1989

By Narong Thasnanipan

This paper presents the outcome of the contest on the prediction of the static axial load capacity of diameter 1.20m bored pile founded at 46m below existing ground. The test pile was constructed by wet-processed method and instrumented with vibrating wire strain gauges. Different methods used by the contestants in prediction of load-settlement characteristics are described and compared with actual load test results. Load-displacement behavior of test pile is found to be better than expected. Major difference between prediction and actual test is the higher frictional resistance of Second Sand Layer achieved in the actual load test. The hyperbolic load transfer method used by one of the contestants was applied to back-analyze the load-displacement characteristics of the test pile at different conditions.

Jan 1, 2006

By Patrick Bermingham

This report presents the results of six STATNAMIC loading tests that were carried out on four different pile types at the CALTRANS 280 Test Site (Bridge No. 34-46) in conjunction with the Tension Pile Test Program. The STATNAMIC testing was performed by Berminghammer Corporation at the request of the California Department of Transportation, Office of Geotechnical Engineering. Others performed the static tension (uplift) and compression loading tests which werecarried out on the piles tested using the STATNAMIC method. A summary of the STATNAMIC test results is presented and discussed, and the appropriate results are compared with the static test results

Jan 1, 1993

By John A. Dal Pino

This paper describes two independent building underpinning projects during the construction of the Los Angeles Metro Rail System. The first project involves pinpile underpinning of a building along the Red Line which is the main heavy-rail portion of the system. Vertical and inclined friction pinpiles were constructed, using drilling equipment in a low-overhead height space, to support underpinning grade beams. This underpinning permitted the demolition of the building caissons so that the subway tunnels could pass beneath the building unimpeded. One of the piles was statically tested in compression. The second project involves the use of traditional pit piers for the underpinning of historic buildings along the Pasadena Blue Line, which is one of the light-rail branches from the Red Line. The piers were designed for various loading conditions and to minimize differential settlement of adjacent foundations. The piers will be internally braced with steel struts to be designed by the contractor.

Jan 1, 1996

By David J. White

The decreasing availability of land in urban areas, and the increasing demand for urban development is leading to the construction of taller and heavier buildings at increasingly marginal sites. Such structures usually require founding at depth and modern construction methods are making the economics of piled foundations ever more attractive (Salgado, 1995). However, the urban environment is not suited to pile driving. Conventional dynamic installation techniques (i.e. drop hammer or vibro-piling) induce vibrations and settlement in a zone close to the pile, and cause noise and dust pollution. Damage to existing structures resulting from pile driving vibrations is not uncommon (Tomlinson, 1986).

Jan 1, 2000

By J. Matos e Silva

"Abstract The paper refers five examples of executed diaphragm walls with one to five levels of anchorages. For each example a comparison is made between the results of the design using the traditional criteria and the ones obtained by using the Eurocode 7 and the Portuguese Norm related to the EC7 (NP EN 1997-1 2010), as the Eurocodes consider the possibility of each European country to adopt their own geotechnical parameters as these may vary from one country to another. A comparison is also made with the behaviour of these diaphragm walls during its construction phase; so the values from the design that were adopted in the construction are listed in tables 2 to 6 in the “Construction Options” columns. From the referred examples the author presents his conclusions.1 - INTRODUCTIONIn the so-called “traditional criteria” the soil parameters (dry unit weight, angle of internal friction and cohesion) have values obtained through tests or empirically. It is assumed that the characteristic values of the soil parameters adopted in Eurocode 7 are equal to the soil parameters adopted in the calculations by the “traditional criteria”. In the present paper the design according to the EC7 was made considering only the ultimate limit states and the respective Cases A1 and A2.The partial coefficients used for the actions in the present paper were those on Table 1:2 - CONSIDERED EXAMPLESThe five examples correspond to the situations of figures 1 to 5, and the respective results are summarized in tables 2 to 6.For all the considered examples, that are case histories, a simplified method published by Matos e Silva (March 2000) was adopted. This method attains good performances when compared with other more sophisticated ones as the finite elements and the elasto-plastic methods as described in a paper published by Matos e Silva (2000). All the obtained values were compared between them and with the so-called “Construction Options” that were the values adopted by the designers of the considered examples. For the wall bottom length calculation two possible situations were envisaged:"

Jan 1, 2014

By Amaneh E. Kenarsari

Among the different sources of uncertainty in pile bearing capacity prediction including inherent heterogeneity, measurement and model uncertainties, the inherent heterogeneity of soil properties is of particular interest and is considered in this study. Cone tip resistance data are utilized to calculate pile bearing capacity by considering vertical soil variability. In this regard, cone tip resistance component of CPT data is assumed as a random parameter. Realizations of this parameter are achieved with the aid of local average subdivisions and random field theories. Monte Carlo simulation is used to generate different realizations of CPT or CPT-u data. Pile bearing capacity was then calculated by the use of direct method. Pile bearing capacity are predicted for a project in south of Iran using this method and probability density function for the total bearing capacity of pile is plotted. Coefficient of variation of 33% for ultimate bearing capacity shows the variability of bearing capacity due to variation of soil strength in depth. Cumulative probability chart for the ultimate bearing capacity are plotted as an efficient tool for estimating ultimate bearing capacity of piles with different desired confidence levels for vertically variable soil strength properties. Significant difference between mean value of pile bearing capacity (18 MN) and limit with 95% confidence level (8 MN) emphasizes the importance of considering soil variability.

Jan 1, 2011

By Peter McDonald

In 1994 the world's largest underwater tunnel was constructed to link Canada and the U.S.A. This new tunnel was large enough to accommodate double-decker railway cars. The construction of an unplanned Retrieval Shaft was required to allow removal and servicing of the Cutterhead of the Tunnel Boring Machine before it passed under the St. Clair River. This paper, which is a revision of that published in Canadian Tunnelling, has been modified here to emphasize construction considerations and describes the evolution of the design and construction of this "Rescue Shaft" under extreme schedule pressure, and changed ground conditions..

Jan 1, 1997

By T. Soejima

In recent years, there has been a tendency in the field of foundation piling works to utilize piles of greater bearing capacity in order to meet increasing height and weight of modern building as a means of saving of piling cost. To satisfy these requirement, a new technique for large diameter bell bottom cast-in-place piling has been developed utilizing multi-head reverse circulation drilling system.

Jan 1, 2010

By Richard J. Finno

This paper presents an overview of methods that can be used to predict damage to buildings as a result of excavation-induced ground movements and describes an adaptive management approach for predicting, monitoring, and controlling excavation-induced ground movements. Successful updating of performance predictions depends equally on reasonable numerical simulations of performance, the type of monitoring data used as observations, and the optimization techniques used to minimize the difference between predictions and observed performance. This paper summarizes each of these factors and emphasizes their inter-dependence. Case studies are presented to illustrate the capabilities of this approach. Examples are given to show how optimized parameters based upon data obtained at early stages of excavation can be used to predict performance at latter stages, and how they can be applied to other excavations in similar geologic conditions.

Jan 1, 2010

By Claudio Asioli

"The project’s goal was to construct the Al Ghazala Intercontinental, a multi-use development in the bay area of Tripoli overlooking the Mediterranean Sea. The site of the project is located approximately 500 ft (150 m) from the Mediterranean coast, near the Al Ghazala roundabout in the town center of Tripoli, Libya. The investor of the project was Magna Properties Group, Ltd. – Libya, the main contractor was Man Enterprise S.A.L., and the design and construction management was performed by Dar Al-Handasah Engineering. Trevi S.p.A. was contracted to perform the design and construction of the anchored diaphragm walls and dewatering systems for the excavation of a two-level basement car park, which extends across the full footprint of the site.The site was approximately 640 ft by 230 ft (195 m by 70 m) in plan and nearly flat. The groundwater level typically varies from about 11 ft to 23 ft (3.4 m to 7.0 m) above mean sea level. To construct the required raft foundation, it was necessary to excavate the area down to El. -15.7 ft to -26.3 ft (-4.8 m to -8.0 m), which resulted in an excavation depth ranging from about 27 ft to 39 ft (8.3 m to 12.0 m) below the existing ground surface.Subsurface ConditionsThe subsurface site investigation was performed in three phases by Al-Tamier Engineering Consulting Bureau. During Phase 1, a preliminary investigation was undertaken during the early stages of the project to obtain information about the general stratigraphy and groundwater level at the site. Phase 2 was performed to obtain subsurface information and design parameters, and Phase 3 was performed as a supplementary ground investigation to investigate unexpected ground conditions identified during Phase 2. In total, 14 boreholes were drilled to depths ranging from about 80 ft to 180 ft (24 to 55 m). The generalized subsurface profile is quite heterogeneous, and is predominantly composed of sand with silt and gravel that is underlain by limestone, calcarenite and claystone"

Jan 1, 2017

By Claudio Asioli

"The project’s goal was to construct the Al Ghazala Intercontinental, a multi-use development in the bay area of Tripoli overlooking the Mediterranean Sea. The site of the project is located approximately 500 ft (150 m) from the Mediterranean coast, near the Al Ghazala roundabout in the town center of Tripoli, Libya. The investor of the project was Magna Properties Group, Ltd. – Libya, the main contractor was Man Enterprise S.A.L., and the design and construction management was performed by Dar Al-Handasah Engineering. Trevi S.p.A. was contracted to perform the design and construction of the anchored diaphragm walls and dewatering systems for the excavation of a two-level basement car park, which extends across the full footprint of the site.The site was approximately 640 ft by 230 ft (195 m by 70 m) in plan and nearly flat. The groundwater level typically varies from about 11 ft to 23 ft (3.4 m to 7.0 m) above mean sea level. To construct the required raft foundation, it was necessary to excavate the area down to El. -15.7 ft to -26.3 ft (-4.8 m to -8.0 m), which resulted in an excavation depth ranging from about 27 ft to 39 ft (8.3 m to 12.0 m) below the existing ground surface. Subsurface ConditionsThe subsurface site investigation was performed in three phases by Al-Tamier Engineering Consulting Bureau. During Phase 1, a preliminary investigation was undertaken during the early stages of the project to obtain information about the general stratigraphy and groundwater level at the site. Phase 2 was performed to obtain subsurface information and design parameters, and Phase 3 was performed as a supplementary ground investigation to investigate unexpected ground conditions identified during Phase 2. In total, 14 boreholes were drilled to depths ranging from about 80 ft to 180 ft (24 to 55 m). The generalized subsurface profile is quite heterogeneous, and is predominantly composed of sand with silt and gravel that is underlain by limestone, calcarenite and claystone."

Jan 1, 2017

By Nicolas Denies, Gust Van Lysebetten, Bart Lameire, Jan Maertens, André Vervoort, Noël Huybrechts, Flor De Cock

"Abstract Originally developed for ground improvement works, the deep mixing method (DMM) has increasingly been applied in recent years for the realization of soil and water retaining structures and as alternative to traditional foundation solutions. From practice, there is a real need for practical guidelines dealing with the execution, the design and the control of such applications. With the aim of developing such guidelines, the BBRI ‘Soil Mix’ project was initiated in 2009. Within this research project, deep soil mix (DSM) material from 38 Belgian construction sites has been tested. In spite of the large advances in the mechanical characterization of the DSM material, one major issue remains the representativeness of the typical core samples in comparison with the real scale behavior of the soil mix elements. There is among others the question of the influence of the unmixed soft soil inclusions on this behavior and the issue of the scale effect which must be considered in the design. In order to investigate these questions, 8 large scale UCS tests and 17 large scale bending tests have been performed on excavated soil mix elements. The present paper discusses results of this experimental campaign, presents some research perspectives and highlights different aspects related to the design of soil mix elements for the realization of retaining wall or foundation solution.INTRODUCTIONSince several decennia, the deep mixing method (DMM) has been used to improve the strength and deformation characteristics of weak soils. In recent years, deep mixing has increasingly been applied – in Belgium and in other countries – for the realization of soil and water retaining structures and alternative foundation concepts. With regard to the execution of the DMM, one can refer to the European standard EN 14679 on deep mixing (2005) that was elaborated under the umbrella of CEN TC 288 “Execution of special geotechnical works”. However, from practice, it has been experienced that this execution standard does not provide enough pragmatic information and guidelines, in particular for the more recent applications of the deep mixing method (with retaining and bearing functions). The same need by the sector for guidance rules linked to design aspects in the context of Eurocode 7 was experienced as well. With the aim of developing such guidelines and in order to provide feedback to the European standardization platforms, the Belgian Building Research Institute (BBRI) has initiated the BBRI ‘Soil Mix’ project (2009-2013) in collaboration with the KU Leuven and the Belgian Association of Foundation Contractors (ABEF), the Belgian branch of the EFFC. Within this research project, deep soil mix (DSM) material from 38 Belgian construction sites, with various soil conditions and for different execution processes (CVR C-mix®, TSM and CSM), has been tested (Denies et al., 2012)."

Jan 1, 2014

By Michael Arnold

"BAUER Foundation Corp. was one of three contractors awarded with the installation of a cut-off wall at the Herbert Hoover Dike Rehabilitation project. The cut-off wall was constructed up to 84 feet deep and 25 inches thick. It extended from the crest through the middle of the existing dike into the underlying peat, sand, and rock layers. BAUER used the cement deep soil mixing method of Cutter Soil Mixing (CSM) to install the wall. Soil mixing was facilitated by first removing the peat layer in the wall alignment using Kelly drilling and replacing it with suitable backfill, resulting in a secant pile wall arrangement of replacement columns. BAUER successfully finished four task orders with a total length of just over 10 miles. Up to six rigs of the types BAUER BG 28, BAUER BG 40 and RTG RG 25 were concurrently used to perform the replacement columns and the cut-off wall installation.The paper introduces the project, the geotechnical site conditions, and the requirements specified by USACE. It focuses on the specific adaptation of the CSM method to the site conditions and on the equipment used. Strength and permeability results obtained from an extensive testing program are presented. The impact of the curing conditions on lab and in-situ test results is studied, and test results are related to soil conditions.PROJECTThe Herbert Hoover Dike is a 143-mile-long dike encircling Lake Okeechobee in south central Florida. When it was constructed in the 1930s and 1960s, the purpose of Herbert Hoover Dike was flood protection from hurricanes. However, during the 1970s a higher lake level was maintained permanently to provide local agriculture with water. Later, damage became apparent during two nearly back-to-back high water events in the 1990s, when numerous sink holes, seeps, pipes, and boils were observed (Fig. 1). In 2000, the Congress approved USACE to propose rehabilitation measures. The installation of a cut-off wall into the existing dike was chosen during the initial design process as the preferred measure to improve the safety of the dike (Davis et al. 2009).The first section of the dike to be rehabilitated was Reach 1 located along the southeast side of the lake between the towns of Port Mayaca and Belle Glade. An indefinite delivery indefinite quantity (IDIQ) multiple award task order contract (MATOC) was issued for this 22.4-mile-long stretch by USACE in 2007. BAUER Foundation Corp. (BAUER) was one of the three contractors that succeeded in the qualification process. Each of the three successful contractors had their own novel construction techniques. In the years 2008 to 2012 BAUER executed four task orders totaling over 10.0 lineal miles of cut-off wall with 3.3 million square feet of design surface area."

Jan 1, 2015

By Nils Schneider, Marc Peters, Stefan Frey, Andrea Fluck

Due to the worldwide population growth, the development of sustainable infrastructure and the exploration of renewable energies plays a key role to handle the rising megacity trends and to limit carbon footprint. Herrenknecht AG is a leading manufacturer of Tunnel Boring machines and has constantly endeavored through its extensive Research and Development programs to address limitations faced by the civil engineering industry as regards to construction equipment capabilities. New mechanized technologies, mainly coming from the tunnelling industry, have been developed by Herrenknecht AG as an efficient alternative to conventional civil engineering, where tailor-made concepts are required to comply with restricted conditions onsite. Very often this innovation led technology capability has meant making construction processes safer due to minimal human intervention and also far more productive due to higher performance as compared to other latest or conventional methods of construction. The rising need for even higher building structures and large-capacity bridges involve the development of innovative deep foundation technologies for on- and offshore operation. Conventional methods like bore piles reach their technical and economic limits under certain conditions. For building shafts and foundations, the mechanized Vertical Shaft Sinking Machine technology (VSM) from Herrenknecht AG is a proven innovation and has now been used in various onshore infrastructure projects worldwide to construct a total of 94 circular shafts in depths of up to 115 meters. It operates below the groundwater level, completely remote-controlled from the surface in a diameter range from 4.5 to 18 meters. Subsequently Herrenknecht noted that Offshore foundations, especially in non-drivable ground conditions such as soft and hard rock (e.g. limestone, sandstone, mudstone, granite etc. or soft soil with high density) and shallow continental shelf (water depth approx. 20-60m), presented construction challenges and equally an opportunity for building high performance equipment. The latter construction conditions usually requires drilled installation methods for applications such as harbor enlargements, bridge foundations and foundations for offshore wind turbines. The Offshore Foundation Drilling technology (OFD®) is Herrenknecht’s latest innovation, incorporating our learnings from the VSM and full-face Tunnel Boring machines, and the OFD® enables a rapid and economical offshore installation in such variable ground and rock conditions. This paper will discuss the technology behind the new mechanized technology of VSM and Herrenknecht’s latest innovation of the OFD® along with their respective application fields in foundations construction. The paper will further present in details, their range of benefits to the construction industry.

Nov 1, 2022

By Hyu-Soung Shin

This study is concerned with the characteristics of the behavior of steel-concrete composite drilled shafts, a material that is used for large bridge foundations, and especially for weak submerged ground conditions. Depending on the loading or boundary conditions considered, the behavior of foundation will vary. The bearing capacity of steel-concrete composite drilled shaft is influenced by initiation and propagation of fractures along the interface between steel casing and filled concrete. The interface effect is taken into account with the following two simplified cases: (1) detached model with free interface (no shear stiffness of interface) between concrete core and steel casing, (2) confined model by an upper steel cap with free interface. In the confined model, it is intended to have an unified behavior of composite shaft between concrete core and steel casing but there is interface between them. Intensive numerical studies have been undertaken to investigate detailed behavior of the composite shaft. In this study, 3-D finite element analysis is employed. Ground conditions typical of those encountered for the design of drilled shaft under water are considered affecting the behavior. Also, an attempt is made to generate possible combinations of the loads which have been considered in fields. Detailed characteristics of the stress and displacement distributions are evaluated to understand the mechanisms of composite shafts.

Jan 1, 2007

By Athena C. Denivo, Pablo V. Lopez, Michael McMaster, Sissy Nikolaou, Alfred H. Brand

"The paper presents the history of development of the United States Tennis Association (USTA) site, focusing on geotechnical, geoseismic, and foundation engineering challenges associated with it. The site is located at the Flushing Meadows Corona Park area of Queens, New York. Now home to the Billie Jean King National Tennis Center (BJKNTC), the site used to be a biologically rich, tidal salt marsh that extended south from Flushing Bay and overlaid an ancient buried valley. In early 20th century, Brooklyn Ash Co. was contracted to fill the marshland with cinders and furnace ashes. F. Scott Fitzgerald describes the “Valley of Ashes” as “a fantastic farm where ashes grow like wheat into ridges and hills and grotesque gardens; where ashes take the forms of houses and chimneys and rising smoke, and finally, with a transcendent effort, of ash-gray men who move dimly and already crumbling through the powdery air.” In 1939 the site was leveled and filled to host the World’s Fair and refilled again for the 1964 World’s Fair.The USTA moved to the site in 1978 and in mid-1990’s constructed the 23,000-seat Arthur Ashe Stadium (AAS). Currently, USTA has a Strategic Vision Plan venue with several interconnected construction projects including buildings, infrastructure upgrades and improvements to site circulation. In addition to a historical walkthrough, the authors will discuss technical challenges of supporting these developments through layers of fill, thick organic silty plastic clays and regional varved soils with bedrock found 300 to 400 feet deep. The subsurface is not only a weak foundation medium, but is susceptible to large amplification of seismic waves propagating from the bedrock during earthquakes. The developments are usually founded on project-specific pile foundations that carry static loads in deeper layers and accommodate lateral demands and performance objectives. Engineering innovations from the most recent development, the roof structure over AAS, will be discussed."

Jan 1, 2016

By Mark R. Svinkin

Construction-induced vibrations may be detrimental to adjacent structures and sensitive electronics operating nearby. Construction vibration sources have a wide range of energy and velocity, as a function of time, transmitted on the ground. Analysis of existing methods for predicting ground and structure vibrations shows that empirical equations provide calculations only of amplitudes of vertical soil vibrations with insufficient accuracy. This paper presents the application of the impulse response function concept to solve the geotechnical problem of predicting ground and structure vibrations before installation of vibration sources. Impulse response functions reflect real behavior of soil and structures without the investigation of soil and structure properties. A procedure is presented to compute predicted ground and structure vibrations. Good agreement is found between predicted and measured records.

Jan 1, 1999

By Clayton A. Signor

Abstract: Expansive soils cause more damage to structures annually than a combination of other major natural disasters. Because of the cost to our society, all means and methods need to be fully explored to mitigate the problems associated with expansive soils. This study will present a foundation design approach that is underutilized in this application, driven piles. The main objective of the study is to present pile test results and analysis from four driven pile project sites in three types of expansive soils found in central Texas: Del Rio formation, Taylor/Navarro formation, and expansive alluvium. High strain dynamic pile tests were conducted on each of the four studies with rigorous signal matching analysis from the CAse Pile Wave Analysis Program (CAPWAP). Ultimate pile capacities ranged from 73 to 311 kips with an average of 61% of the total capacity coming from the pile shaft and were two to six times the structural capacity needed. Allowable loads calculated from Modified Gates dynamic formula best modeled allowable test results. Average unit skin frictions ranged from 0.50 to 4.71 ksf. Restrike pile tests of 1 to 17 days after initial driving reported 30 to 100% shaft capacity gain. All open-ended pipe piles driven produced soil plugs ranging from 4 to 14 feet thick. Small diameter, thick-walled, open-ended pipe piles reached penetration of twice the depth of designated zone of seasonal moisture change without problem. The observed production rate of the driven piles was on average 8 minutes, which implied daily production of 15 to 40 piles. Predrills or augered holes should be specified for underground obstructions found in soil investigation.

By J. J. Beresford

The primary function of a support slurry is to provide stability during excavation. Today foundation structures can be designed around the additional friction afforded by the absence of the filter cake attributable to the use of polymeric fluids as support slurries. These fluids use pseudoplastic fluid viscosity to advantage over the fragile thixotropic gel structures of bentonite. Many of today's polymeric fluids are environmentally acceptable for disposal directly to municipal sewers.

Jan 1, 1989