Search Documents

By Blandine Arseneault

The Raglan Mill had been in production for less than a year when the initial toxicity tests on the effluent revealed that it was defined as ?toxic? under regulations. Testwork was begun to address the fundamental reasons for the toxicity and a systematic approach was initiated to identify causes. Elimination of the problem presented a challenge once the main conclusion identified high dissolved solids as the principal culprit. In particular, normally benign soda ash (sodium bicarbonate) reagent additions used in milling, was identified as the main contributor to the problem. Following analysis of all requirements and safety considerations, a concept to recycle 100% of the mill process water was pursued. In addition to meeting regulatory requirements, this project would have numerous positive benefits to the operation, including reducing fresh water consumption and lowering costs.

Nov 1, 2002

By Jan Nemcik

Among other products steel mesh has been used successfully for many years to support strata and minimise loose material from falling into the mine opening. Installation of steel mesh has proven to be difficult to automate and many other products, such as Thin Spray-on Liners (TSL), have been proposed as a replacement. Ideally, the mechanical properties of these products should be superior to those of the steel mesh, however, most TSL trialled in mines to date have been weak and in addition have had slow cure times, as a result none of these materials can seriously compete with steel mesh. Now a new polymer product that cures in seconds and forms a stiff strata binder that surpasses the properties of steel mesh is under development at the University of Wollongong. To enable selection of a suitable polymer material for roadway skin reinforcement several numerical models were constructed to investigate the role of interface roughness and the influence of polymer stiffness on load transfer along the rock-polymer interface. Laboratory tests indicate that the shear adhesion of the rock-polymer interface can be substantial while the tensile adhesion can be much lower. The models indicate that the natural stone roughness and surface waviness plays a major role in shear adhesion while the elastic properties of polymer liner can significantly influence the polymer ability to resist fracture opening.

Oct 1, 2009

By R. D. H. Wigmore

"The title of this paper probably sounds quite simple and self-explanatory. The problem, however, was not a simple one, and proved somewhat baffling and expensive over a period of years. After outlining the problem, and the methods which were used to overcome it, we will present our solution, or perhaps it would be more accurate to say the partial solution which we reached.We have in the cyanide circuit at Upper Canada two Dorr Single Tray Thickeners with 30 ft. diameter wood stave tanks 12 ft 4 1/ 2 in. deep. In the years prior to 1948, when the tonnage was 250 to 280 tons per day, two stage thickening was practised. As the tonnage was increased to 450, 500, and finally 560-600 the thickeners were used in parallel.Some settling problems were encountered, and in those days the means to combat these problems were very few. The only remedy was to dump in pounds and pounds of lime. Then along came a few reagents, and the writer remembers one in particular, - 11 Carboxel11 (carboxymethlycellulose). When water or solution was added to this reagent, the result was a gooey mass somewhat resembling tapioca. One drawback was that it stayed in this state, and didn't go anywhere. A method was finally developed of containing the mass (or mess) on a fine screen, and dissolving some of it was a fine spray of solution. The only thing the writer recalls was that it was not a very effective settling agent.Shortly after this time, along came the new flocculents, first a few, and then many, and our settling problems were over.But when the settling problem was solved at Upper Canada, some other problems were creeping up on us."

Jan 1, 1965

Mining companies around the globe have long struggled with the need to ensure that earth moving equipment is designed to be operated and maintained under all site conditions without causing harm to people. Incident and accident data from a range of sources clearly identify mining equipment related issues as major causal factors. One Australian source, the NSW Department of Primary Industries? International Mining Fatality Database Project Report (2008) noted that ?Approximately 77% of mining accidents resulting in a fatality have? involved equipment?. The largest number of fatalities were associated with trucks; the next with LHDs. Many of the technical advances in equipment design over the past few decades have not been matched by advances in the human factors design of mining equipment, resulting in a ?design vacuum? that must be filled prior to commissioning new equipment. This ?design vacuum? is generally filled by local dealers. They retrofit equipment according to customer requirements to mitigate risks that have not been designed out by the Original Equipment Manufacturer (OEM). Mining companies have been frustrated by lost time and additional costs associated with this need to retrofit ex-factory designs. Some companies have attempted to address the problem by negotiating company or site-wide ?solutions? to equipment designs, but this has not simplified or clarified the issue from the point of view of the equipment manufacturers. A number of mining companies operating in Australia first discussed the concept of a joint customer approach to improve the Human Factors design of earth moving equipment at the factory level in 2004. They agreed that a new approach to engaging with OEMs was needed; one that would define the ?Problem?, in other words, the basis of the risks, rather than dictate the ?Solution?. The Earth Moving Equipment Safety Round Table (EMESRT) was formally established in 2006 by six global mining companies to establish a process of engagement between Original Equipment Manufacturers (OEMs) and mining customers.

May 1, 2009

By R. W. Nice

"For many decades the incidence of a highly active graphite-like ore has plagued the McIntyre mine. This ore acts as a precipitant of the gold complex immediately upon formation of this complex. The gold is subsequently discharged with the tailings.Many different methods have been devised by various researchers all of which proved inapplicable for the McIntyre problem.Recently, McIntyre personnel, through their own research, developed a flowsheet. This circuit should give an overall recovery of 36% which is below the 94% experienced in the mill at present. Therefore, less revenue would arise from treatment of these ores. On the other hand there exists a possibility of more efficient mining methods in some of this ore thus allowing more economic recovery.INTRODUCTION This paper has been prepared to serve two purposes:i) To propose a method of recoverying gold from a sizeable orebody at the McIntyre mine at Schumacher.ii) To summarize and present the many methods suggested to solve a very old but very real mineral dressing problem familiar to the industry as long as cyanidation itself."

Jan 1, 1971

By U. Troncoso

Mantoverde is a heap leach-SX-EW operation that was commissioned in December 1995 at a production rate of 42,130 ton of copper per year and 5.4 million ton of ore per year. Copper production has been steadily increased to reach 62,000 ton in 2005. The forecast copper production for 2006 is 60,300 ton for an ore treatment rate of 9.5 million ton. A first dump leach operation was started in 1999 at a production rate of 1,922 ton of copper. A second dump leach operation was started in early 2002 at a production rate of 2,805 ton of copper. Dump leach production will be increased over time to as much as 24,000 ton of copper. Several improvements in the heap leach process have been implemented to cope with the higher ore throughput and copper production. However, the solvent extraction plant has remained unchanged which has resulted in a lower availability of raffinate solution and, as a consequence, in longer leach cycles. Different studies have been undertaken in order to optimize the solution management system at Mantoverde, including column test work aimed to reduce the leach cycle and solvent extraction plant modifications aimed to increase the raffinate solution availability. The test work program and the economical evaluations carried out, as well as the conclusions and recommendations obtained, are discussed in this paper.

Jan 1, 2007

By Z. D. Hora

Brick shales and refractory clays are mined at Sumas Mountain near Abbotsford. Sholes and stoneware clays elsewhere in the province have not been developed. THE SUMAS MOUNTAIN deposit near Abbotsford, 80 km east of Vancouver, has been in continuous production since 1905. The deposit is exposed in a small outlier and comprises a sequence of alternating beds of clay and sand. Beds are of Eocene age. Within the 400 m thick ness of sediments are seven distinctive conglomerate members, some up to 20 m thick, interbedded with fine grained sediments including claystones and siltstone , or "shales". Shale is quarried to produce a variety of bricks, sewer pipes and similar products; it is also used for cement. Several different shale beds have been mined over the years and exhibit a variety of fired colours ranging from buff-pink grey to deep red; pyrometric cone equivalents (PCE) range from 3 to 20. A layer of fireclay 3 to 4 m thick that occurs at the base of the sequence has pinkish white to light buff fired colour and PCE of 30 to 33. It is used as a 266 primary component to produce refractory bricks. The shale is quarried and processed by Clayburn Industries Limited of Abbotsford. Another similar but smaller outlier of the same geological formation is known from Blue Mountain, about 20 km northwest of Mission. Other ceramic clays in British Columbia are reported from Quesnel (7 m bed of white stoneware clay, PCE 17 to 19), Giscome Rapids (25 km north of Prince George, 10 m bed of stoneware clay to PCE 31) and anaimo-Comox area (buff to red firing "shales", PCE 8 to 10-1 12) . From 1959 to 1974 Cretaceous shale from Saturna Island in the Strait of Georgia was used to produce lightweight aggregate. Similar deposits of expanding shale are known from the vicinity of Duncan on Vancouver Island.

Jan 1, 1984

By O. Hall

DISCUSSION AT QUEBEC MEETING MR. A. V. CORLETT: With drill holes radiating from a common point, is loading carried to the collars, and do you undertake to distribute the powder evenly? MR. R. V. PORRITT: When the collars of the holes, particularly the diamond-drill holes, are close together, two out of three holes are loaded only to within six or seven feet of the collars, and the intervening holes are loaded close to the collars. When the collars are farther apart, the holes are loaded close to the collars. No spacers are used, and the holes are filled solid with powder, this applying particularly to the diamond-drill holes, except, of course, where the collars are close together and some holes are not loaded close to the collars. MR. J. G. L. McCREA: I would like to enquire in respect to the various efforts made to reduce the cost of diamond drilling to the lowest point, what is. the relative cost of the solid bit to the standard bit? It would seem that the solid bit has the higher cost. MR. PORRITT: The non-coring or solid bit gives a slightly lower diamond cost than the coring bit. With the coring bit, the greatest diamond loss is on the inside stones, apparently due partly to vibration, but mainly to the core blocking against these stones. This condition, of course, does not apply with the non-coring bit. Our experience is that the non-coring bit, which drills out a much greater area, has a diamond consumption slightly less than the coring bit. The non-coring bit is sturdier, and is far less liable to damage in starting holes and in drilling through cracked or broken ground.

Jan 1, 1939

By W. J. Witte, M. K. Witte

"INTRODUCTION A pilot heap leach project was conducted on the B. P. Selco Hope Brook ore located in southwestern Newfoundland. The pilot heap leach was undertaken to assess and confirm the following:1) To confirm that heap leach technology now currently used in the United States could be applicable to Canadian sites.2) To confirm gold recovery by the Heap Leach technology3) To assess and study potential heap leach environmental concerns in cold and wet climate.PROJECT LOCATIONThe Hope Brook Project is located near the southern coast of the island of Newfoundland, approximately 100 kilometers southeast from Stephenville, approximately 25 kilometers west of Burgeo, Newfoundland. Access to the property is limited to helicopter, float plane or by sea through Couteau Bay. The property was covered with muskeg and very few trees. Surface relief was moderate with many poorly drained boggy sections confined to small areas. Many small unnamed lakes were located on the property which provided water to small brooks and streams flowing to Couteau Bay.Several locations were reviewed for the installation of the pilot heap leach facility. Important parameters used to select a suitable location included sufficient land area, close proximity to but not on the ore body, reasonable protection from wind, sufficient supply of fresh water, close to a suitable location for a portable crushing plant, reasonable access to aggregate material for preparation of the test pad and ponds and suitable contours to minimize site preparation."

Jan 1, 1987

By G. D. Hibbard

New regions of material property space can be accessed by combining microstructural design at the nm-scale with architectural design at the µm- or mm-scale. In the first case, large strength increases associated with grain size reduction to below 50 nm have driven extensive research efforts into the development of nanocrystalline materials [e.g. 1-3]. For many potential structural applications, however, the density of a nanocrystalline material is just as important as its strength. In fact, reducing the density is more important than increasing the strength for certain weight specific materials performance indices, and it is especially critical for applying structural nanomaterials in the aerospace and automotive sectors. We have developed a new type of structural nanomaterial wherein the effective density of the parent metal is reduced by more than an order of magnitude by incorporating an internal periodic cellular architecture of open space. In one example a low density cellular nanocrystalline material was created by electroforming nanocrystalline Ni around a rapid-prototyped acrylic photopolymer microtruss, Figure 1 [4]. Microtruss materials have periodic cellular architectures that are specifically designed to undergo stretching-dominated deformation as opposed to the bending-dominated deformation in conventional open cell metal foams [5,6]. This new cellular nanocrystalline hybrid material combined the structural efficiency of microtruss architectures with the ultra-high strength that can be achieved by grain size reduction to the nm-scale. Although it played a critical role as a cathode support during the initial stages of nanocrystalline electrodeposition, the polymer core did not contribute significantly to the inelastic buckling resistance of the composite metal/polymer struts and it may therefore be desirable to remove it post deposition by means of chemical dissolution or thermal decomposition [4]. Nanocrystalline electrodeposition can also be used to reinforce conventional cellular metals (Figure 2), creating new types of cellular composites such as metal/metal microtruss hybrids [7-10] and metal/metal foam hybrids [11,12]. For example, nanocrystalline Ni-Fe alloy sleeve thicknesses of up to 400 µm were used to reinforce an aluminum alloy microtruss that had been fabricated using a stretch-bend approach; the nanocrystalline sleeves had the effect of increasing the microtruss strength by up to a factor of twelve and the specific strength by a factor of three [8]. Alternatively, much thinner sleeves can be electroplated to produce structural coatings. In one example, a nanocrystalline Ni coating was designed to provide both corrosion protection and inelastic buckling resistance [10]. Because the ultra-high strength material was optimally located at the furthest distance from the neutral bending axis, only a thin coating of 50 µm was needed to double the inelastic buckling resistance of the 1.13 mm x 0.63 mm cross-section plain carbon steel struts [10]. Overall, the mechanical performance increase that can be obtained through electrodeposition depends on a complex interaction between the starting cellular architecture and the nanocrystalline sleeves.

Jan 1, 2010

By M. D. Quinn

THE sand and gravel used for backfilling at the Hollinger mine is obtained from deposits in a low range of hills some three miles north of the mine, where the Company owns a number of claims. The material is transported to the mine by aerial tram. Shipments from these deposits to the Hollinger mine commenced in June, 1927, and since May, 1936, sand has been supplied also to the McIntyre mine. During 1942, Hollinger requirements were 1,700 tons per day, and 900 tons per day was delivered to McIntyre. For the past seven years production has averaged 900,000 tons annually, and total deliveries to the end of 1942 were 13,129,022 tons, of which 11,075,339 tons went to Hollinger and 2,053,683 tons to McIntyre. Some years ago, when the original pit was approaching exhaustion, new workings were opened on claims east and south of the tramway terminal. It soon became apparent that the sand varies considerably in character from place to place. The weight per cubic foot was found to range from 85 to 130 lb., and the water percolation rate from 2 to 50 inches per hour. As the mine requirement is a sand with percolation rate of 6 inches or better per hour, it was evident that in certain parts of the deposits the material was not suitable for use as backfill. As a consequence, it was decided to carry out a programme of systematic sampling of the claims in order to select the areas containing suitable material for back-fill and at the same time estimate the tonnage available.

Jan 1, 1944

By Y. T. John Kwong

Abstract - To exploit an ore deposit without unduly impacting the environment is a challenge that can only be met by the concerted efforts of traditionally independent teams working on a mining project. Not only is detailed geology required of geologists to help mine engineers to develop a mine plan that assures generation of the least possible amount of mine waste, but metallurgists also have to select the most environmentally friendly mineral processing schemes, and communicate with environmental engineers with regard to complications that process chemicals may pose on proper mine waste management. Traditional ore deposit models typically emphasize the geological and mineralogical aspects of ore genesis to facilitate exploration for similar deposits. Recent research has shown that potential environmental liabilities such as acid mine drainage and metal leaching can readily be predicted according to deposit types. The choice of mining methods, mineral processing schemes, and decommissioning options are also largely dictated by the composition and setting of an orebody to be mined. Integrating such related information into traditional ore deposit descriptions would lead to the development of comprehensive environmental ore deposit models. The latter would facilitate communication among staff of the varied components of a mine project and aid with the selection of a combination of methods and strategies that would assure minimum environmental risks and impacts, reduce the overall project cost, and enhance sustainable development.

Jan 1, 2003

By Andrew Popko

Introducing EnCana ?? A leading North American Oil and Gas company ?? Focused on natural gas and oil sands development in 12 key resource play areas across North America ?? In 2007, over 4300 wells drilled, producing about Enterprise value of approximately $50 billion ?? Invest between $5.8 Billion in 2007 ?? Over 7500 employees ?? Headquarters ? Calgary, AB

May 1, 2008

By H. Ardehali, P. Lind

Many gold deposits also contain significant quantities of deleterious elements such as arsenic. Several biological pathways are possible for arsenic exposure; special care and caution must be used while undertaking metallurgical testwork on ores and concentrates that contain high levels of arsenic. Laboratory precautions pertaining to handling of airborne dust concentrations, necessary personal protective equipment, and effluent treatment are discussed.

Jan 1, 2014

By P. J. Mackey, Elsie Kossatz

The small town of Bruce Mines lies a few miles east of Sault Ste. Marie, Ontario on the north shore of Lake Huron. This was the site of the first copper mine. This copper smelter used a reverberatory furnace, based on the Welsh process, and operated in the period of 1849 to 1850, when the plant was destroyed by fire. During the period of 1850 to about 1869, crushed and sorted ore was shipped to England and later to the United States. In 1869, a roastleach plant, based on the Henderson Process, was constructed at Bruce Mines and was operated until about 1872. This short article describes the early development of this historic operation. Although the rich copper ore found in the vicinity of Bruce Mines was known to the Indians, its discovery in or about 184 7 was credited to Mr. Keating, who named the area Bruce in honour of Lord Elgin (James Bruce), Canada's Governor General. In 1848, the property was acquired by the Montreal Mining Company for 40 000 pounds sterling and the company immediately sent a small party to investigate the deposit. The party sank a shaft on a lode within a hundred yards of the lake and also reported two adjacent lodes farther inland, which were left undeveloped until the turn of the century. Initially, the foundation of the headframe and hoist was built above the frost line and when the machinery was set in motion it collapsed. Eventually, the shaft was to reach a depth of 300 feet. By 1849, the property was well established and the small settlement consisted of 77 miners, 65 labourers, 4 boys, 11 tradesmen, including blacksmiths and carpenters, 2 mining captains, 1 engineer, 2 clerks and 1 superintendent. The community, including the workers' families, numbered about 250.

Jan 1, 1999

By Simon P. Fricker

Gold drugs have been used for the treatment of rheumatoid arthritis since the mid 20th century as disease-modifying antirheumatic drugs (DMARD) class. Methotrexate is often the preferred DMARD, and with the advent of new therapies gold drugs are now used infrequently. Since the introduction of auranofin in 1985 there has been no new clinically approved gold drug. In spite of this apparent lack of progress there has been a great deal of interest in the use of gold compounds for cancer therapy and early promising indications were achieved with a gold phosphine complex [Au(dppe)2]Cl. This compound was not entered for clinical trials, however, due to problems with cardiotoxicity highlighted during pre-clinical toxicology studies. Gold(III) is isoelectronic (d8) with platinum(II) and likewise forms square planar complexes. It is therefore tempting to speculate that such complexes would have similar antitumor activity to cisplatin. In order to stabilise the gold(III) oxidation cycloaurated complexes were synthesised with a single mononegative bidentate ligand, damp, (2-[(dimethylamino)methyl]phenyl), and two monodentate anionic ligands e.g. Cl or acetate. The damp ligand forms part of a five-membered chelate ring. The monodentate ligands are readily hydrolysed and are available for substitution. These compounds had limited anti-tumor activity in in vivo against human tumor xenografts. Mechanistic studies indicated that these compounds had a different mechanism of action to cisplatin. An alternative molecular target for these compounds is biologically important thiol-containing molecules such as the cysteine protease cathepsin B. Modifications were made to the Au(III) damp structure to give compounds with a six-membered chelate ring. These compounds were shown to be inhibitors of cathepsin B. Compounds were also tested for cytotoxicity against a panel of human tumor cell lines. Three compounds were selected for further evaluation against a human colon tumor xenograft. The compounds showed modest anti-tumor activity but with no marked improvement over the parent Au(III)damp complexes. Initial indications are that Au(III) compounds targeted against disease-specific thiol-containing biological molecules have potential as drugs, particularly for cancer. However, further work is required to produce a target-specific drug with a suitable pharmacological activity and toxicity profile.

Oct 1, 2003

By George Hope, Dave Green, Jacques McMullen

The Est Malartic mill has been treating massive sulphide, copper/gold ore from the Bousquet 2 mine since 1989. The need to minimize copper content in flotation tails which are leached for gold recovery and to produce a saleable copper concentrate led to the evaluation of Conventional, Column and HG flotation methods. The HG method was preferred and two full-scale cells were installed and operated over a two-year span. In 1992, it was decided to expand the mill capacity from 1500 tpd to 2500 tpd. A total of nine additional HG Tank Cells were installed to provide additional roughing and cleaning capacity. The expanded plant has been operating since June 1993.

Jan 1, 1994

By Denis Landry

"RÉSUMÉAu cours de dix dernières années, la compagnie Maghemite a développé, expérimenté et breveté un nouveau precédé de concentration du minerai de fer à partir de la récupération d'hématite présente au bassin de sédimentation de la Compagnie Minière Québec Cartier.A partir de cette nouvelle technologie de concentration par induction, la compagnie Maghemite produit une poudre d'hématite qui est mélangée avec du strontium carbonate à un ratio de l à 6 en poids. Le mélange homogène est achemine sur un disque d'agglomération, et ensuite incorpore dans la fournaise de la Compagnie Minière Québec Cartier. Le temps de cuisson et la température (l200°C) correspondent exactement aux critères nécessaires pour la fabrication d'aimants de céramique, Grade 5, à partir de la poudre de ferrite.IntroductionMeghemite a débuté sa production de poudre de ferrite au printemps 1986et prévoit une production de 20 000 tonnes par année dans cette nouvelle usine. A très court terrne, une usine sera construite pour la production de cinq à dix millions de Iivres d'aimants permanents par annee et à long terme qu'une usine de fabrication par robotique de moteurs à aimants permanents, utilises dans I'industrie automobile. La poudre de ferrite à base de strontium est une compose ferro-magnétique forme d'une molécule d'oxide de strontium et de six molécules d'hernatite. Ce compose d'hexa fluorite de strontium a une force tres puissante et fournit la source d'énergie magnétique la moins dispendieuse comparée aux autres aimants permanents. L'utilisation des aimants de céramique formes d'hexa fluorite de strontium a connu un croissance phenornenale depuis 1970 pour atteindre un marché de 500 millions de livres par année en 1985.II n'y a aucune autre usine de production commerciale de poudre de ferrite à base de strontium au Canada. Le facteur determinant qui a favorise l'etabilissement a Port Cartier est base sur la réduction de 30% du cout des aimants de cerarnique provenant de notre poudre. Notre debouche majeur se situe aux États-Unis et vise la production des aimants de cerarnique pour les moteurs utilises dans les automobiles, les ordinateurs et les appareils ménagers, L'objectif de cette compagnie est de réduire le prix futur des aimants de cerarnique à environ 30% du prix actuel.L'usine commerciale de production de poudre de ferrite est maintenant opérationnelle. Le financement et la construction de cette usine sont Ie résultat de l'opération d'une usine pilote sur une période de 5 ans afin de récupérer l'hematite d'un haut niveau de pureté provenant de résidus de I'usine de bouletage de la Compagnie Minière Québec Cartier (CMQC) à Port Cartier. La fournaise de CMQC est utilisee pour chauffer les boulettes cornposees d'un mélange de carbonate de strontium et d'hematite d'un haut niveau de pureté en étalant environ 5 tonnes à l'heure de ces boulettes au-dessus du tablier de boulettes de fer dans une des fournaises fonctionnant à environ 450 tonnes à l'heure."

Jan 1, 1987

By Patrick J. Williams

Outline -An Australian View On: ?IOCG defining features and occurrence ?Variable exploration characteristics ?Extracting value (gold metallurgy) ?Recent exploration experience(case study)

Apr 1, 2005

By R. Browner, J. Collard, D. Ibana

The extraction of cobalt from synthetic pressure acid leach solutions of nickel laterite ores by the direct solvent extraction route using ESPLIM is reported. It first explored the use of gaseous ammonia as pH modifier and then the variables that affect the dispersion of the aqueous phase in the organic phase such as ionic strength, viscosity of the phases, initial droplet size, etc. were explored so that phase hold-up and thus extraction can be effectively controlled. The results show that the technique allows better control of phase dispersion circumventing one of the main weaknesses of conventional solvent extraction.

Jan 1, 2005