Search Documents

By Yuki Soma, Tsutomu Ogawa, Jae Hyung Hong, Toshihiro Nagato

The Saganoseki flash furnace was built in 1973. The steel frames of the flash furnace were designed to absorb the expansion of refractories and contain expansion-absorbing materials between their frames and the skin plate. Expansion and deformation resulted in the furnace settler because of the repeated increase and decrease in temperature from more than 30 maintenance shutdowns. Preliminary investigations were conducted to confirm the condition of the settler, and it was found that partial cracks accompanied the expansion in the lower layer of the refractories. As a result, the risk of molten-matte leakage increased. Based on the above investigation, it was decided that the entire settler should be replaced by introducing a spring-displacement structure that was capable of maintaining the furnace integrity over an extended period. The difficult redesign and rebuilding of the Saganoseki flash furnace was accomplished successfully and safely in 76 days from September to December 2017, as planned. Because of various redesigns, the furnace was changed to a flash-smelting furnace that can withstand higher thermal loads based on recent trends of copper concentrate with increased sulfur and reduced copper. The new furnace is operating smoothly at present. INTRODUCTION The flash-smelting furnace of Pan Pacific Copper Co., Ltd. Saganoseki Smelting & Refinary commenced operation in 1973, with an original designed feeding rate of 71 t/h. As a result of facility remodeling and operational improvements, shown in Figure 1, the feeding rate was increased to 215 t/h in recent years. After more than 40 years of operation, the original settler in the melt holding section of the flash furnace underwent significant expansion and deformation.

Jan 1, 2019

By Young C. Kim

A proper economic analysis of pit slope design must reflect the trade-off between the benefits and the increased risk of slope failure inherent in steeper slope angles. However, no formal framework for a proper analysis has existed to date. This paper summarizes the material contained in the Design Chapter Supplement (5-3) of the Pit Slope Manual. The supplement describes the results of the research effort in which a formal economic analysis framework was developed and tested through a case study. The case study results have demonstrated the practicality of the developed procedure and the availability of required data under "real-life" conditions.

Jan 1, 1979

By Peter Godbehere, Christian Desroches, Viken Baboudjian

"Noranda Copper Smelting and Refining is a unit of Noranda Metallurgy Inc., comprising the Home smelter in Rouyn-Noranda, Quebec and the C.C.R. Refinery in Montreal East. The Home smelter provides custom smelting services for a wide variety of copper and precious metal bearing concentrates and recyclable materials, producing over 200 000 tonnes of anodes and 450 000 tonnes of sulphuric acid annually. The C.C.R. Refinery has an annual production of 360 000 tonnes of copper cathode, and is a major refiner of precious metals.Over the past twenty years, Noranda Copper has developed innovative processes and operating techniques to treat the ever increasing complexity of primary feed materials, while improving the quality of its final products, working conditions and reducing environmental emissions.This paper presents an overview of the operating practices of Noranda Copper with particular emphasis on the impact of impurities in the smelting and refining processes.IntroductionThe treatment of custom materials has been practiced by Noranda Copper since commencement of operations at the Home smelter in 1927 and the CCR refinery in 1931. Copper concentrates from a wide variety of regional, North American and overseas producers account for the bulk of the 800 000 tonnes treated annually, although recyclable and secondaries have increased in importance as feed sources in the past two decades. The geographical disadvantage of the Horne smelter compared with most custom smelters located on tidewater has provided an important incentive for Noranda Copper to develop the necessary technology and operating practices at its smelter and refinery to treat high value complex concentrates and other feeds containing significant concentrations of bismuth, antimony, arsenic, lead, tellurium, mercury, etc."

Jan 1, 1995

By G. E. Agar, W. B. Kipkie

"This paper deals with the prediction of locked cycle flotation results from data developed from individual batch tests. A postulate is made that the distribution of material in a separation stage is determined by the chemical conditions and the flotation time and that this distribution can be characterized by split factors which are constants for a fixed set of conditions. With this premise, it is demonstrated that a steady state balance can be calculated for a circuit.Although the necessary equations can be solved algebraically, a computer program was written that uses an iterative tec1nique to arrive at the steady state balance. The program is written so that a variety of circuits can readily be simulated.A number of examples are examined to demonstrate the validity of this simulation procedure. The sensitivity of the material balance to changes in the split factors was examined. Data developed from different flowsheets is presented on sulfide ores, on copper-nickel separation and on silver flotation,"

Jan 1, 1978

By H. Dundar

The first application of High Pressure Grinding Rolls was in 1985 at a cement plant, for the purpose of capacity improvement. Then various circuit configurations were derived to achieve a reduction in overall specific energy consumption, by transferring more of the grinding required to the HPGR. In most circuit configurations, the recycle of fines is required for effective breakage between the rollers. By increasing the fines amount in the feed material to a specific level within the recycling load, a uniform material bed is created and a higher pressure gradient along the roller width is obtained, resulting in compact flakes, including more fines. The fines recycle results in enhancement of the interparticle breakage. This paper will discuss the effect of the feed size distribution on HPGR performance.

Jan 1, 2012

By Z. Wu, L. N. Y. Wong

The present study develops the numerical manifold method (NMM) as a tool to investigate the progressive failure in rock slopes. The entire processes of the progressive slide surface development related to crack initiation, propagation, coalescence and degradation to eventual catastrophic failure are successfully captured. To overcome the limitation of the original NMM associated with an improper removal of the interface cohesion of the discontinuities, the displacement-dependent cohesion removal method is adopted. Simple examples of failure of rock slopes containing different arrangements of discontinuities are modeled and their results are compared with those based on the popular limit equilibrium method proposed by famous pioneers Jennings and Jaeger. In cases of coplanar non-persistent discontinuities, close results are obtained despite the differences in the consideration of the stress concentrations at the crack/discontinuity tips. In cases of non-coplanar discontinuities, since the influence of the tensile strength is considered by both the Jaegers model and the NMM, the Factor of Safety (SF) values are similar despite the difference in the failure path trajectories predicted by these two models. The results also reveal that the original NMM without the displacement-dependent cohesion removal method is always more conservative due to the improper removal of the interface cohesion. The displacementdependent cohesion method can to some extent alleviate such a limitation.

Jan 1, 2015

By J. B. McKenzie

Since connnencing underground prcxiuction in 1979, the Ruttan Mine has been prone to secon:iacy sulphide dust explosions. Al though infrequent during the early years of prcxiuction, these occurrences did result in major damage and lost time injuries. 'As the mine exparrled and developed to further depths, sulphide dust explosions occurred on a more frequent basis. Incomplete ventilation se:rvices, required to exhaust the affected areas, caused frequent delays resulting in lower prcxiuction rates due to the time required to ventilate the affected areas of the mine. CUrrent procedures to minimize the effects of secon:iacy dust explosions evolved from practical suggestions arrl examining methcx:ls other mines have developed to cope with the problem. Procedures and regulations to protect errployees from exposure to hazards of sulphur dioxide are time consuming, expensive and counter prcxiuctive in their present fonn. This paper describes the history of secon:iacy sulphide dust explosions at the Ruttan Mine and the methcx:ls and proced.ures currently in place to minimize and contain the effects of dust explosions.

May 11, 1988

By Chen Bang, Xia Xiao’ou, Zhang Feng

"Ores with compressive strength lower than 150 MPa are usually easy to be crushed by conventional jaw crushers and cone crushers. However, for hard ores with compressive strength exceeding 150 MPa and 200 MPa and even up to 250 MPa, such as andesite, hard basalt and olivine, it is difficult to reach satisfactory crushing size and yield or difficult to meet service life and stability use requirements of quick-wear parts by using conventional crushers. As continued increase in ore mining depth and constant generation of new type materials, equipment demand for crushing hard ores becomes increasing high. A new type inertia vibrating crusher is designed. It is powered by a high-speed rotating vibration exciter and can obtain required crushing force by adjusting eccentric mass, eccentricity and rotating speed so as to crush various ores with high hardness. This paper introduces the design process of its structure and working principle, discusses the design calculation methods of vibration excitation system, vibration damping and energy storage system and other key mechanism and provides technical references for this type of vibrating crusher.DESIGN PHILOSOPHYThe conventional jaw crusher mainly acquires extrusion force from crank motion to realize crushing. The motor drives the eccentric shaft via the transmission device to bring the moving jaw to swing relative to the stationary jaw. When the moving jaw moves close to the stationary jaw, ores between them are crushed by extrusion; when the moving jaw moves away from the stationary jaw, crushed ores are discharged from the discharge gate at the lower end between the moving jaw and the stationary jaw.The conventional spring cone crusher and the hydraulic cone crusher mainly acquire extrusion force from cranking motion to realize crushing. The motor drives the eccentric sleeve via the transmission device, the moving cone shaft generates an eccentric distance to make cranking motion under the action of the eccentric sleeve. When the moving cone moves close to the stationary cone, ores between them are crushed by extrusion. When the moving cone moves away from the stationary jaw, crushed ores are discharged from the discharge gate at the lower end between the moving cone and the stationary cone under the action of dead weight."

Jan 1, 2016

By P. L. Wright

"This is a brief history of the development of the mining project, with a description of the proven geology. The paper describes how the experiences gained progressively demanded change in the mine design. The equipment used is described, together with methods of working. Interesting facts have been proved regarding gas emissions and roof. supi;iort. The. working cycles evolved are completely flexible m operation and lend themselves to maximum utilization of the most productive units. The two underground mines are compared, showing the variance in conditions already experienced. Programs currently in operation to improve standards and production are: the training of miners, maintenance men and officials; experiments in floor consolidation and continuing roof support trials; and the effect of comparative stability of working crews on the performance of the operation."

Jan 1, 1973

By Greg Johnson

Maintenance needs information about assets to optimize availability and production needs information about performance and consumption to maximize output. In considering both these needs together as, ?Asset Optimization?, the information systems that support them are critical. The theory of Asset Optimization derives from the Lean Manufacturing concepts developed by Toyota, but some changes are required to apply this to mining operations. In particular, mining operations require automated systems due to their geographic spread and they need a strong emphasis on capturing under-performance losses as well as delays and stoppages in production. Leading metal miners and coal miners alike have applied these systems to good effect in the last 10 years. The concepts developed initially in minerals processing plants are now being applied to the mines themsleves as well as the mining logistics chain. Production increases of 5?10% are achievable with the right implementation and consideration of the some key lessons learnt in the last 10 years. Putting these lessons into action is one key step in the goal of optimizing asset performance and thus utilizing the resource at lowest cost.

Aug 1, 2013

By W. D. Fogwill, P. J. Clarke

"The Dawn Lake uranium deposits are located 340 km north of La Ronge, Saskatchewan, in the Athabasca Basin between the Midwest Lake and Rabbit Lake deposits. Four zones of uranium mineralization, called the ""11, 14, 11A and 11B Zones,"" lie within the Athabasca Sandstone, at the sub-Athabasca unconformity and in the basement.At Dawn Lake, approximately 100 metres of Helikian Athabasca Group clastic sediments overlie Aphebian Wollaston Group pelitic and calcareous metasediments and pegmatites. Uranium with some nickel, cobalt and copper, occurs near the sheared stratigraphic contact between calc-silicate gneiss and graphitic, pyritic pelite. The mineralization lies in an area of low magnetic susceptibility which is thought to represent a rock sequence lying stratigraphically high within the Wollaston Group. There is no obvious vertical displacement of the unconformity by faulting, despite considerable brecciation, shearing and slickensides seen in the basement rocks. This suggests horizontal displacement on steeply dipping wrench faults as the main tectonic control along the 11, 11A and 11B trend.Below the Athabasca unconformity, the Wollaston Group rocks are altered to fine-grained mixtures of clays, chlorite and silica commonly called regolith. Along the mineralized trend post-Athabasca fracturing and (or) compaction have occurred through this clay-rich alteration zone, causing the steeply-dipping primary foliation to become contorted. This ""crenulated"" horizon can reach depths of 35 metres below the unconformity and is thickest along fault zones in the calc-silicate rocks. The ""crenulite"" is a distinctive unit which at Dawn Lake is commonly found above pods of ore located deep below the unconformity.Much of the mineralization in the 11A and 11B Zones occurs above, beside and below the thickest part of the crenulated zone, although the crenulated rock itself contains negligible amounts of carbonate, pyrite and uranium. Intense vuggy alteration and collapse breccias are found in calc-silicate rocks deeper and to the west of the 11A and 11B mineralization. There are at least two ages of uranium deposition in the basement zones, shown by small bright cubes of ""pitchblende /"" overgrown and replaced by duller botryoidal ""pitchblende II. ""Sooty pitchblende and yellow secondary minerals are the result of still younger reworking.The geological setting of mineralization, along the contact between carbonate-rich calc-silicate rock and pyritic pelite, suggests that the uranium was concentrated at a pH/Eh boundary located between deeply weathered, carbonate-rich and sulphide-rich basement rocks."

Jan 1, 1986

By Vern Evans

Saskatchewan has historically been recognized for farming, but in 1943 while drilling for oil, potash was discovered. The initial attempt to gain access to the potash beds was unsuccessful, however, subsequent attempts were successful and today there are ten operating potash mines in Saskatchewan. In this paper we will provide a brief overview of the historical and current Potash industry in Saskatchewan.

May 1, 2011

By R. J. Chase, C. Davies

"The Merelani graphite-tanzanite deposit is located in northeast Tanzania, 14 kilometers south of Kilimajaro International Airport and in close proximity to the towns of Moshi and Arusha. The graphite mineralization is hosted by relatively undeformed linear Proterozoic metasedimentary gneisses, several of which have been subjected to hydrothermal alteration resulting in tanzanite mineralization. Exploration work comprised detailed geological mapping coupled with pit and trench channel sampling and a subsequent 1500 meters of diamond drilling. In addition, metallurgical tests have shown the graphite to be of unusually coarse flake size, crystallinity and high purity.Feasability studies have shown the economic viability of a major coarse flake graphite deposit with the measured resource to 50 meters in excess of 9 million tonnes assaying over 85 graphitic carbon. Production is due to start by the end of the first quarter of 1994 with the processing plant design capacity initially set at 15 000 tonnes per annum.In addition to graphite production, tanzanite will be produced through selective mining within the graphite open pit in the upper horizon and from underground workings within the lower horizon.The Merelani graphite-tanzanite deposit will be the first major orebody to be exploited through means of private funding since Tanzania gained independence"

Jan 1, 1994

The total current inventory of mature fine tailings is estimated to be nearly 850 million m³. Pressure has come to bear on the industry to accelerate its tailings management practices and prevent this inventory from steadily growing. The present paper describes the treatment, management and reclamation of fluid fine tailings. New technologies being evaluated include: i) Thin layered - fines dominated deposits, ii) Deep - fines dominated deposits, iii) Fines enriched sand deposits, and finally iv) water capped disposal in end pit lakes. A brief overview for each of the methods of treatment and disposal for fluid fine tailings is provided.

Aug 1, 2013

By W. Beres, R. E. Miller, B. Shiari, L. R. Zhao

A dynamic multiscale simulation method has been developed to study the material scratching processes on nanoscale single crystals. The model simultaneously captures the atomistic mechanisms near the free surface and the long range mobility of dislocations and their interactions, without the computational cost of full atomistic simulations. The method also permits the simulation of system sizes that are approaching experimentally accessible systems, albeit in 2D. Simulations are performed on single crystal aluminum to study the atomistic details, surface evolution, and generation and propagation of dislocations for a variety of scratching depths at room temperature. Simulations demonstrate the power of the developed method in capturing both long-range dislocation plasticity and short-range atomistic phenomena during tool advance. Variations of scratching normal and tangential forces are investigated and related to plastic deformation and dislocations generation during the simulation process.

Jan 1, 2006

By John H. Fowler

"Barytes is one of the major components of drilling fluids used in oil and gas well-drilling. This mineral's close association with the petroleum industry bestows it with a commodity status not enjoyed by many other industrial minerals. Approximately 85% of world barytes production is used as a weighting agent in oil and gas well drilling while the remaining 15% is consumed mainly in the manufacture of barium chemicals, glass and as a pigment, filler or extender.Barytes mining began in Nova Scotia around 1865 and has continued until the present. Currently there are three barytes producers in the province one exporting pharmaceutical-grade barium sulphate and the other two supplying drilling mud-grade barytes to the offshore. Several barytes exploration and development programs are underway with excellent possibilities that Nova Scotia deposits will supply a significantly larger share of the drilling mud-grade barytes used in east coast drilling programs.Currently there is renewed interest in barytes activities in Nova Scotia because of its use as a weighting agent in drilling flu ids used in offshore oil and gas drilling programs.This paper reviews the use of barytes by the well drilling industry; outlines the history of barytes mining in the province, progressing to present-day exploration, development and production activities underway in Nova Scotia; and concludes with the market potential for Nova Scotia barytes."

Jan 1, 1986

"No questions.F Energy Consumption in Industrial Minerals : E.Joe No questions.g Automatic Dewaterinq at Mattagami : M. CaronE. Marcotte Is the control valve on the thickener underflow reducedFalconbridge as the pulp density reduces?Reply As the slurry density reduces the valve will constrict to reduce the flow and the density will re-establish itself.E. Marcotte Is there a stopper on the valve to prevent its closing too far?Reply We never shut it off completely because of the danger of sanding. It is just brought down to a normal level. It works very well within a given range and the operator is on hand to prevent any sanding out in the line."

Jan 1, 1984

By Brian Hart, Stamen Dimov, Aparup Chattopadhyay, Barun K. Gorain

"A novel gold deportment technique has been developed for complex copper-gold and double refractory gold ores using state-of-the-art technology. Characterization of these ores is a challenging task due to low copper and gold grades in ores, presence of both primary and secondary copper sulfide phases and variable proportion of visible and invisible gold in different sulfides and iron oxide phases.Double refractory ores are mainly composed of silicates and carbonates with moderate clay and mica, and minor amounts of sulfides and organic carbonaceous matter. Gold mostly occurs as ""invisible gold"" (sub-microscopic gold) as solid solution or as colloidal-sized particles in different sulfides and other phases. The dominance of invisible gold and presence of highly preg-robbing and finely disseminated carbonaceous matter adversely affects gold recovery in flotation and leach circuits. Characterization of this carbonaceous matter, commonly known as TCM and quantification of gold associated within TCM, along with different sulfide and oxide phases is highly complex and challenging.Studies were initiated on various complex ore deposits and also on samples representing various process streams. This paper presents the development of a systematic approach to diagnostic metallurgy using state-of-the-art optical and automated mineralogy techniques, namely, micro-probe, dynamic SIMS and TOF-SIMS analysis for quantification of invisible and visible precious metal content in various species. The relevance of the mineralogy characterization to metallurgy will also be discussed in this paper."

Jan 1, 2016

By Geoffrey C. Streeton

A continual objective of mine operations is to reduce ground control costs without compromising the overall safety or performance of the installed ground support. Any change in the ground support regime must not result in a less secure or safe workplace. The due diligence required to implement a change in rockbolting practice is extensive, particularly when the new bolting system has not been used at any other mining operation. Factors such as yield, shear strength and embedment strength must all be investigated to gain an understanding of how the rockbolt can be expected to perform. This paper also discusses the substantial cost reductions and efficiency gains which can be achieved through the introduction of the Jumbolt rockbolt.

May 1, 2001

By K. E. Haque

"This paper is a brief overview of the role of oxygen in cyanide leaching of gold feeds (e.g. ore, concentrate). As the majority of gold occurs in the elemental state (Au °), its oxidation is of vital importance for dissolution in the cyanide lixiviant. The cyanidetion at high pH is favourable for the oxidation of Au° with a mild oxidant such as air or oxygen. Beside oxidation of gold, deleterious effects of soluble sulphides, arsenates, antimonates on cyanidation of gold can be alleviated by preaerating the leach slurry with air or oxygen (i.e. preaeration process).If gold is refractory due to its occlusion in sulphides, silicates, tellurides, etc. then gold liberation is possible by roasting in the presence of oxygen or by leaching under oxygen pressure. The data in the recent literature indicate that reactive oxygen supplied by H202, Na202, Ca02 or 03 during cyanidation can accelerate considerably gold oxidation-cyanidation and yield high gold recovery in much shorter leach time. The information compiled in this review leads to the conclusion that oxygen plays a vital role in the dissolution of gold in cyanide lixiviant."

Jan 1, 1992