Search Documents

By L. Xia, B. Hart, J. Nigim, Z. Chen

"Grinding ore is an important step in the flotation process. Not only does grinding reduce particle size and liberate minerals, it also creates conditions for reactions to occur on particle surfaces that can aide or inhibit flotation. There have been numerous studies examining various grinding regiments and the effect on flotation pulp chemistry, including autogenous grinding and using media of variable composition. There have been however, few studies looking at the effect of variability in grinding media size on pulp chemistry and subsequent flotation. This study attempts to link changes in pulp chemistry in response to variations in grinding media size to flotation recovery. It uses probes mounted in the grinding chamber (pH, Eh, DO, and conductivity) to monitor pulp chemistry changes during grinding of a Cu-Zn ore. Surface chemistry analysis by ToF-SIMS was performed on sphalerite from the mill discharge. Activator and depressant species were monitored on the mineral surfaces and their presence was evaluated in the context of variability in pulp chemistry linked to differences in grinding media and its ball size.INTRODUCTIONIt has been widely recognised that not only does grinding reduce particle size and liberate minerals but the grinding environment has a large effect on the flotation of sulphide minerals. This effect is attributed to Eh change, iron hydroxide coating on surfaces, oxygen reduction, precipitation from solution and galvanic coupling (Grano, 2009). As early as 1960, it was reported that after grinding the ores in an iron mill the natural floatability of sphalerite was reduced significantly (Rey and Formanek, 1960). Kocabag and Smith (1985) studied on the industrial circuits showing that the depression of sulphides flotation in a steel mill is possibly due to the coating of iron oxidation products. Peng, Grano, Fornasiero, and Ralston (2003a, 2003b) found that iron contamination from grinding media plays a dominant role in depressing galena and chalcopyrite flotation. Huang, Grano, and Skinner (2006) reported the same observation in the flotation of arsenopyrite."

Jan 1, 2016

"In the past year, mining at the Doyon Mine has shifted entirely from open pit to underground. The mine produced 234 692 ounces of gold in 1989 and is expected to produce 225000 ounces in 1990. The Doyon Mill has been running slightly above design capacity, and recovery has increased 3%.IntroductionThe Doyon Mine is located 25 miles east of Rouyn-Noranda, Quebec (Figure I).It is a joint venture owned by Lac Minerals and Cambior, with each holding a 50% interest. Lac Minerals operates the mine under the direction of a management committee.Production at the Doyon Mine began in 1980 with the start up of the Main Zone pit. Shortly thereafter the Doyon Mine became the largest open pit gold producer in Canada.In 1983, a ramp leading to the fourth level and exploration drifts were driven. Results were very encouraging, therefore the decision was made to sink a 2150-foot deep shaft, which was completed in 1986.In mid-1986, production began in the West pit, while underground mining of the West Zone started shortly thereafter, at the end of the same year.In 1987 the mill capacity was increased to 3300 tons per day and the Main Zone underground operations commenced."

Jan 1, 1990

By David Rahal, Saul Ortiz, Maria Escobedo

The general trend in the minerals industry is towards the processing of fine grained, disseminated mineral deposits. This has led to an increase in the number of fine/ultra-fine grinding installations using stirred media mills. The challenge is that both the equipment type and the mineralogy of the deposit have an effect on specific energy consumption. Fresnillo PLC recognized this issue and addressed it by providing samples for testing in a laboratory regrind system. The objective of the test program was to determine the specific energy required to achieve a product size of 10 µm (P80). A specific energy plot was generated for both a lead and zinc flotation concentrate. It indicated that 34 kWh/t and 51 kWh/t were required for the two samples (Pb and Zn respectively). This difference highlights the effect of mineralogy on the energy required for fine grinding. The regrind feed and products were submitted to a range of basic mineralogy tests to quantify the mineral differences that could have changed the specific energy requirements. These tests provided general mineralogy, documented optical textures, and provided particle size microscopy. The lead concentrate was found to contain significant amounts of silicates in addition to the dominant sulphide, pyrite. The zinc concentrate was determined to be mostly sphalerite with minor amounts of quartz, chalcopyrite, pyrite and galena. The material testing results illustrate the importance of basic mineralogy studies in conjunction with comminution testing to determine specific energy consumption.

Jan 1, 2016

By G. W. Davies

"IntroductionThe development of British Columbia's northeast coal deposits, represents the single biggest industrial undertaking in British Columbia's history.As a result of this development, several thousand jobs were created, hundreds of millions of dollars in new tax revenue and billions of dollars in new foreign exchange began flowing into Canada.The Northeast Coal Development began in 1981 with the signing of sales contracts to ship a total of 6.5 million tonnes of metallurgical and additional quantities of thermal coal annually to Japan over a 15-year period. The current long-term agreements contain provisions for extension to 20 years.The sales contracts with a group of Japanese steel mills were signed by two Vancouver-based mining companies, Quintette Coal Limited and Teck Corporation. The agreements followed years of exploration and negotiation beginning in 1968.The first shipment of coal from Quintette and Teck's Bullrnoose Mine was transported by BC Rail and Canadian National Railways to the Ridley Island coal port in the fall of 1983."

Jan 1, 1992

By Samuel Frimpong

Green house gases have become a major concern within the international community over the last two decades due to their potential link to global warming. Carbon dioxide (CO2) is the principal greenhouse gas. In the Kyoto Agreement, Canada has committed to reduce emissions by 6 % below 1990 levels by 2012. This presents a serious economic challenge to Canada and Alberta. Over the next decade, oil sands production expansion, population and industry growth and energy demand will increase CO2 emissions. Current and future CO2 emissions and their economic implications in Alberta will be critical in formulating a comprehensive and balanced policy for dealing with concerns in this area. Disposal of carbon dioxide (CO2) in land aquifers is a potentially viable option for Alberta in dealing with long-term CO2 emissions. Studies have confirmed the existence of appropriate aquifers in the Alberta Basin for CO2 storage over a long geological period. Carbon dioxide is an ideal candidate for aquifer disposal because of its high density and solubility in water at relatively high pressures. In this study, the authors develop a computer simulation model of a scaled aquifer disposal system. The scaled model consists of an injector well, aquifer environment with dominant Ca++ and Mg++ cations. Liquefied CO2 is injected at an appropriate pressure and concentration through an injector well model. The injected CO2 migrates from the point of contact between the injector well and the aquifer domain to the main regime of the latter. The rate of migration is a function of porosity, permeability, cations, aquifer fluid flow regime and CO2 injected pressure. These models are validated using flue gas data from the 546 MW Wabamum Power Plant in Alberta. The total energy requirements for aquifer CO2 disposal system are distributed between a minimum of 105 MW and a maximum of 172 MW, with a mean of 132 MW and a coefficient of variation of 10%. The results show that there is significant variability in all the energy requirements for the CO2 disposal system. The total energy requirements for the disposal system as a fraction of the total power generated by the Wabamum plant of 546 MW could be between 0.19 and 0.32. This is a very significant energy requirement and thorough analysis must be carried out to reduce this variability and energy requirements.

May 1, 2001

By R. D. Lindsay

Originally the focus of Deak Resources Corporation Business Plan was to establish a method for treating small gold and possibly base metal mineral deposits located in the Kirkland Lake - Noranda area of Northeastern Ontario, Northwestern Quebec at a central treatment facility. Since the establishment of this original business plan in 1988 other processing options have availed themselves for handling the base metal ores off site at a central facility which may preclude their processing at Deak.The site selected for the Deak processing plant was Kerr Addison's Virginiatown operation. At the time this property was acquired from the Receiver following Golden Shield Resources' Bankruptcy in 1989 the mill had been processing in the order of 1, 100 SDT per calendar day through one processing module; a module originally designed to process 1,500 SDT/day of a free milling gold ore. This tonnage level however had not been achieved since 1966 when an average throughput of 1481 SDT per calendar day was recorded.In order to realize Deak's overall Business Plan it would be necessary to expand the mills processing capabilities to provide:(1) A 2200 SOT per day circuit capable of processing a free milling, medium work index gold ore;(2) a 1 ,000 SDT per day flotation and/or cyanidation circuit capable of processing refractory gold bearing materials containing refractory minerals (i.e. copper) that should be removed prior to cyanidation; and possibly(3) a 1200 to 1500 SDT/day base metal circuit capable of processing the broad range of Deaks' Base Metal Property ores. If this circuit were introduced it would be completed in two tonnage phases.Further, it was recognized when operations resumed under Deak in 1990 that the existing tailings dam was suitable for, and had sufficient capacity for additional gold tailings with necessary physical modifications and changes in disposal techniques (including the construction of containment storage cells) that would allow storage for an additional 3.4 million tons of gold ore tailings approximately 1.0 million of which has been deposited since 1990. The focus of Deak's long term tailings disposal strategy is to acquire the Barber Lake Basin which is currently adjoined to our main tailings system which will provide an additional 10 million tons of storage capacity.

Jan 1, 1993

By Chris V. Sellathamby

Condition-based maintenance is replacing preventive maintenance in many industrial operations as a result of gains in productivity. Preventive maintenance is strictly time-based which means that as long as the prescribed time is sufficiently short, failures are prevented. The trade-offs between shorter cycles and increased downtime is a fine balancing act. Condition-based maintenance is gaining momentum as the more cost-effective and green solution to finding the optimal maintenance cycle and improving overall productivity. In the mining industry, various parameters of heavy equipment are monitored continuously to provide feedback for maintenance events. However, strain, shock, and vibration, key factors which lead to yielding and fatigue of metal parts, are not generally monitored by built-in systems, mainly due to the complexity of sensor installation and computational intensity of data processing. Scanimetrics has developed a stand-alone, add-on wireless system for measuring strain, shock, and vibration in heavy equipment and components, the data from which can be directly used to trigger maintenance events. The present system is being deployed in tar sands mining equipment. The system consists of a portable display and control unit, a software platform consisting of data management, sensor instrumentation and data analysis, and wireless strain sensor units, which can be easily installed on equipment. Data from the sensors can be gathered throughout the mine site, processed instantly, and used to generate condition-based maintenance events, improving overall uptime of the equipment and overall productivity of the mining operation.

Oct 1, 2010

By Peter Babik

"Cable TV networks are extensively used throughout Canada for TV signal distribution. Mobile/portable radio communications are also used extensively throughout all sectors of industry. There are numerous manufacturer supplying these industries with a wide variety of equipment and accessories.IAL's underground radio communications system combines the techniques of cable TV and mobile radio to produce a flexible communications system with most of the advantages of both systems. Standard off-the-shelf mobile, portable, base-station and repeater equipment can be used. The equipment may need modification to be customized to particular end user requirements, but does not require a complete new unit redesign. Likewise, the cable TV distribution equipment is off the-shelf, with some items requiring modification for underground system application.Radio communications can be provided wherever the cable system is extended. Where traffic or type of activity warrants it, multiple radio channels can be provided on the same cable. Certain radio channels could also be used with data channels for control or supervision of remote equipment or environmental conditions. In addition, the same cable can be used to distribute or monitor signals from remote TV cameras in selected or dangerous areas. The system can be interfaced to a telephone system, if required, to provide extended communications to above-ground workshops, offices, medical stations or even hospitals and other emergency services.IntroductionReliable communications among personnel throughout an underground mine area have long been the dream and goal of various mine operations personnel. The system to be described was designed to meet this objective."

Jan 1, 1983

By Hans D. Gougar

To meet an increasing demand for minerals, mining operations are moving to ever more remote regions. The lack of a local energy supply and infrastructure, coupled with social and regulatory demands for lowered environmental impact of mining operations, presents an opportunity for a seemingly unlikely competitor ? a nuclear power plant. The Modular Pebble Bed Reactor concept, currently in various stages of research and development around the world, offers a high degree of reliability and safety with minimal consequences for the local or global environment. The passive safety features of this design eliminate the need for the extensive active safety systems that add significantly to the cost of current water-cooled reactors. With the MPBR, as with all nuclear plants, there are no appreciable quantities of waste products released to the environment during normal operations. In contrast with conventional reactor designs, the MPBR would also remain radiologically safe even under the most severe abnormal circumstances. The key to the design is the fuel element. Enriched uranium microspheres are coated with various layers of pyrolytic carbons and silicon carbide to form a highly-temperature resistant particle that effectively retains all fission products. These particles are mixed with graphite and formed into 6 cm pebbles. A randomly packed vessel of such pebbles forms the reactor core through which helium is circulated as a coolant. Computer models and tests performed on actual pebble bed reactors confirm that fuel failure temperatures are not reached even during the most severe conceivable loss of coolant accident. The reactor drives a gas turbine cycle with resulting efficiencies as high as 48%, comparable to natural gas-fired units. The low price of uranium fuel and low maintenance requirements translates into competitive operating costs. However, high capital costs prevent the MPBR from competing with natural gas in most markets. In remote applications where no fossil supplies are readily available, the playing field is more level. This paper summarizes the features of two of the more promising candidates for remote applications and discusses the strengths of the MPBR from the perspectives of fuel supply and environmental impact.

May 1, 2002

By R. J. McLeod

"A new backfill plant was constructed in 1966 adjacent to the mill of Giant Yellowknife Mines. The reasons for the addition were to increase the storage capacity for sand fill, provide facilities for mixing cement with the fill for mine stope floors and provide a system for pumping fill to B -3 raise, a horizontal distance of 4700 feet from the mill. At the same time it was hoped to increase the density of the fill pumped underground.The plant consists of two only steel storage tanks of approximately 400 tons capacity of sand fill each. They are 17 feet in diameter and have conical bottoms. The cylindrical section is 28 feet high and the conical section 14 feet high. Each tank is fitted with water nozzles around the conical sections to remove solids at the required density. The water pressure on the nozzles is 150 lbs per square inch. The cyclones used to produce the sand back fill are located on top of the storage tanks. Five model Dl0B Kreb cyclones are used for this purpose. The vortex finders are 2 1/ 4 inch and the apex 1 1/4 inch. The cement silo or storage tank is located in the same building. It is a steel tank 17 feet diameter by 41 feet high with a conical bottom. The silo holds 250 tons of bulk cement, which is unloaded by air from a bulk highway carrier using 12 to 15 lbs air pressure. The cement is conveyed to the top of the silo, a distance of 70 feet from the ground by 450 lbs. of air.The mixing tank is a rubber lined steel tank 14 feet in diameter by 14 feet high. It is equipped with a Lightning Mixer supplied by Greey Mixing Equipment Ltd. The mechanism is driven by a 40 HP motor. The lower shaft is unsupported and is equipped with two 36 inch diameter axial flow turbine type rubber covered impellers. The backfill is discharged from the storage tank into the mixing tank by a 5"" x 4"" SRL-C pump powered by a 20 HP motor. A level control in the mixing tank regulates the rate of discharge of this pump through a Grinnell-Saunders automatic control valve. The cement silo is situated at such a height above the mixing tank to allow for a Rota-Lock, a small hopper and a cement feeder. The feeder is an Omega gravimetric belt type dry feeder with a Sensogram controller. The capacity of the cement feeder is 20 tons of cement per hour. The cement and backfill are mixed in the mixing tank at whatever ratio is required for the mine stope floors."

Jan 1, 1968

By R. P. Mahant

"Extensive pilot plant investigations were conducted both on partial roasting an d electric furnace smelting from September 1973 to August 1975.The objectives of the pilot plant investigations were:(I ) to confirm the application of available process technology to treatment of Falconbridge concentrate.(2) to examine partial roasting variables.(3) to investigate electric furnace smelting of roaster calcines .(4) to develop process design and operating parameters for a commercial plant.This part of the paper will cover the following topics:Partial Roasting InvestigationsPilot Electric Furnace InvestigationsPartial Roasting InvestigationsThe specific objectives were to:1. establish process variables for maximum oxygen efficiency and bed fluidi ation.2. determine the product distribution between the roaster and the various gas cleaning stages.3. produce a mass and thermal balance."

Jan 1, 1984

By Francis Dakubo, Courtney Young, Avimanyu Das

"Hydrometallurgy of copper ores typically involve acid leaching followed by solvent extraction and electrowinning (SX/EW). EW is the final purification stage in which a voltage is applied across two electrodes causing the copper ions to reduce and deposit on the cathode. Applied voltages are near 2 volts with current densities around 300 amps/m2. In this study, research was undertaken to decrease the energy consumed in the EW process. To do this, various cell designs were constructed and tested in which a membrane was used to separate the cathode and anode compartments with concentrated solution from SX serving as catholyte and raffinate from SX serving as anolyte. Therefore, copper in the concentrated solution would be deposited on the cathode while ferrous in the raffinate would be oxidized to ferric at the anode. Because it is assumed that ferric acid leaching is used, resulting ferric would be recycled to the leaching process. A positive side effect of the envisioned process would be the elimination of oxygen evolution at the anode and thus the prevention of acid-misting. After a cell design was selected, it was used to test a number of variables: flowrate, concentration, temperature, ion-exchange membrane, and applied voltage. Following experiments in which variable ranges were determined, statistical modeling was conducted using STATEASE software. Optimal results indicate the voltage can be decreased to 1.5-1.7 volts with current densities of 300-400 amps/m2. Significant reduction in the energy consumption was accomplished by reducing the applied voltage. Furthermore, current efficiencies and copper production rates was increased by application of the membrane.INTRODUCTIONLeaching of copper ores is achieved using mostly sulfuric acid. The copper pregnant solution is contacted with an organic solvent or resin adsorbent which picks up copper ions as in Equation 1:"

Jan 1, 2016

By Alexandre Desbarats, Michel David

"All optimum pit design studies start from the geological are reserves inventory, the estimated grades of all blocks of potential are within the interpreted limits of the deposit. The actual optimization procedure is then carried out on block valuations based on these estimated grades. Thus, the relevance of any pit design can be seen to depend directly on the ore reserve estimation . To insure a proper pit design, a first step would be to use a geostatistical reserve estimation technique such as kriging, however, this is not enough. A frequently neglected fact is that the blocks of ore estimated during the planning stage of the mine are usually considerably larger than those on which the ore-waste selection will be made at the time of mining. Experience in the exploitation of large low-grade deposits has shown that large blocks, estimated to be are, when mined selectively in smaller blocks, often yield significant amounts of waste material. This phenomenon, known as internal waste, is a function of the variability of the grades, the size of mining unit and the amount of sampling information on which ore-waste decisions are made.In this study, it was proposed to consider the effect of internal waste caused by selective mining, on. pit design, using geostatistical methods to predict the tonnage and grade of recoverable reserves within large blocks.Optimum pits obtained using a block valuation formula taking into account the recoverable reserves within large blocks were compared with optimum pits obtained using a conventional block valuation formula. It was found that the optimum pits obtained by the proposed method had the highest total valuations and thus were, in fact, ""more optimum”. These pits were characterized by greater are tonnages at a lower average grade, the additional ore more than compensating for the drop in grade. It was also found that the consideration of internal waste in pit design could considerably alter pit limits in marginal areas of the deposit.It was concluded that selective mining had a significant, potentially critical, impact on the design of optimum pits especially in the case of large low-grade deposits."

Jan 1, 1984

By Craig H. B. Leitch

"In describing the alteration of porphyry systems, the term ""secondary K-feldspar"" appears to be an oversimplification. A better term would be ""alkali feldspar"" alteration, because in actual fact the replacement feldspars show gradational changes from an albite, which is important in some systems, to an alkali feldspar containing minor orthoclase molecule, to true orthoclase.There are several textural varieties of secondary alkali feldspar present in the porphyry systems studied from British Columbia, Australia and New Zealand. These include, in apparent increasing order of alteration intensity: clear albite (An10); patchwork albite (An5-10); chessboard albite (An0-10); ""irregular albite "" (An0Ab100 to Ab90Or10); untwinned ""anoralbite"" (Ab90Or10 – Ab70Or30); and orthoclase (Ab40Or60 - Or100)·The exploration significance of these varieties of alkali feldspar is that their gradation in composition, from sodic to potassic, may be linked to a corresponding increase in intensity of alteration. Thus, there is a tendency for more sodic alteration feldspars to characterize weak, sub-economic deposits, or the fringe zones of stronger deposits; the more potassic alteration feldspars may provide an exploration vector toward more highly mineralized zones."

Jan 1, 1981

By Craig H. B. Leitch

"In describing the alteration of porphyry systems, the term ""secondary K-feldspar"" appears to be an oversimplification. A better term would be ""alkali feldspar"" alteration, because in actual fact the replacement feldspars show gradational changes from an albite, which is important in some systems, to an alkali feldspar containing minor orthoclase molecule, to true orthoclase.There are several textural varieties of secondary alkali feldspar present in the porphyry systems studied from British Columbia, Australia and New Zealand. These include, in apparent increasing order of alteration intensity: clear albite (An10); patchwork albite (Ab5-10); chessboard albite (An0-10) "" irregular albite "" (An0Ab100 to Ab90r10); untwinned "" anoralbite"" (Ab90Or-Ab70Or30); and orthoclase (Ab440Or60-Or100)·The exploration significance of these varieties of alkali feldspar is that their gradation in composition, from sodic to potassic, may be linked to a corresponding increase in intensity of alteration. Thus, there is a tendency for more sodic alteration feldspars to characterize weak, sub-economic deposits, or the fringe zones of stronger deposits; the more potassic alteration feldspars may provide an exploration vector toward more highly mineralized zones."

Jan 1, 1981

By C. Poon

For slope stability, knowledge of major and minor discontinuity sets that form the rock mass fabric is paramount for pit slope designs. Due to the increased awareness of health and safety in mining projects, efforts have been made to limit structural mapping in order to minimize the risk to personnel associated with approaching potentially unstable areas. Recognizing the importance of such safety precautions, Golder Associates Ltd. is applying a combination of techniques including 3D photogrammetry, conventional mapping and drilling with core orientation to enhance structural data collection. Photogrammetry uses digital photographs to produce a virtual model of a rock mass surface. The application of these techniques will be exemplified through an expansion design of an existing open pit. A comparison of stereonets obtained using these techniques showed some agreements, but also highlighted limitations of each method. The application of photogrammetry was found to be very useful in complementing the other existing techniques.

May 1, 2009

By James Stenhouse

Abstract The aqueous oxidation of pyrite in caustic solutions under oxygen pressure was investigated by measuring that effect of reaction variable on oxygen consumption by the reactions. From the results of this investigation, a model for the process has been proposed. In this model, sulphur diffuses as a positive ion through an oxide layer which forms on the sulphide particles and is then oxidized to sulphate ion. Iron is oxidized by substitutional diffusion of oxygen atoms into the oxide layer. The effect of most reaction variables on the rate of oxygen consumption can be explained with this model. Introduction Recent investigations (1,2,3) have shown that certain sulphide ores can be readily leached by agitating the ore in the form of a pulp under pressure in the presence of oxygen. Since very little was known of the mechanism of this oxidation, a programme of investigation was inaugurated in 1949 in the laboratories of the Department of Mining and Metallurgy of the University of British Columbia. Financial support for the investigation was received from the National Research Council in the form of student grants and bursaries, from the Canadian Liquid Air Company, Limited, and from the Consolidated Mining and Smelting Company of Canada, Limited. The first objective was to devise a technique to study the primary oxidation reactions in aqueous solutions and to apply the technique to a detailed study of the oxidation of pyrite in caustic solutions.

Jan 1, 1952

By F. Kapeller, G. Herget

"The need for monitoring the effect of changes in ground stresses due to mining in hard rock has existed for many years. The Mining Research Laboratories of CANMET, EMR have developed a new tool which monitors with high precision the radial deformation in boreholes. The result is the Mining Research Laboratories strain monitoring system (MSMS) which uses the highly stable and very sensitive vibrating wire principle to monitor deformations in relatively large boreholes, e.g. 76 mm to 153 mm diameter.The vibrating wire is strung across a relatively large proving ring and operates at a frequency between 600 to 1800 Hz. The read-out system is based on continuous vibration.The ring is installed with a hydraulic tool and brought into contact with the surrounding rock through precisely machined and guided wedges. The resolution of the system is in the neighbourhood of 4 x 10-4 min/ Hz. The data collection can be carried out with a portable read-out unit and provisions are available for automatic data collection. Stresses may be calculated from strain readings.The system was tested in cooperation with the Centre de recherches minérales at the Niobec Mine in Quebec for the purpose of monitoring the effects of drill drift development and slope mining on surrounding ground stresses.After access was available to the site, 153 mm diameter holes were drilled for the determination of in situ ground stresses. These holes were then used to install the strain monitoring system. The effect of drill drift development and production blasting in stopes C-203-13 and C-203-15 on ground stress distribution could be observed clearly.The horizontal relaxation in the core of a pillar which occurred during mining of adjacent rooms was between 0.082 mm to 0.111 mm. Calculations of stresses from these deformations indicate that the rock material is still in an elastic condition.Roctest of Montreal has obtained a license on the manufacturing and distribution rights. A patent has been registered and CANMET will assist in installation of the MRL strain monitoring system and the interpretation of records."

Jan 1, 1989

By J. Kuipers, R. W. Lawrence, P. B. Marchant, W. Brooks, J. T. Chapman

"Bioleach testing and piloting was conducted on refractory gold sulphide concentrate from Austin Gold Venture in Nevada during 1988. The objective of the test programme was to determine the technical and commercial viability of bioleaching as a concentrate pretreatment step prior to gold extraction by cyanidation. Baseline CIL cyanidation typically resulted in < 20% gold extraction from the Austin concentrate. Bioleaching enhanced gold extraction up to 95% using conventional CIL techniques. This paper summarizes the bioleach test programme and results, including pilot plant studies onsite, and describes the commercial design details for a possible retrofit of the Austin flotation tailings leach circuit to accommodate 20 tpd and 40 tpd capacity concentrate bioleach facilities.INTRODUCTIONBioleach testing on a refractory carbonaceous sulphide concentrate from Austin Gold Venture (AGV), was initiated in late 1987 as part of an ongoing programme at Austin to investigate alternatives to concentrate smelting. Preliminary batch biooxidation tests at Coastech indicated that over 90% gold extraction by carbon-in-leach (CIL) cyanidation of the bioleach residue could be achieved, compared with less than 20% gold extraction on untreated concentrate by similar CIL processing.Subsequently, a more rigorous laboratory study was undertaken at Coastech to establish continuous biooxidation operating criteria on a bench scale. The objective of continuous testing in the laboratory was to provide confirmation of enhanced CIL response based on continuous bioleach products and to determine key process operating and design parameters for pilot testing. The success of the laboratory test program led to the installation of a mobile pilot plant at Austin Gold Venture. The plant was operated by Coastech and AGV during 1988 to provide scaleup data and design criteria for commercial design and feasibility analysis. Based on pilot plant operating data, a detailed commercial bioleach plant was designed as a possible retrofit to the existing 1000 tpd CIL plant. Capital and operating costs were estimated to provide a commercial feasibility study of bioleaching as an oxidative pretreatment for Austin refractory concentrate."

Jan 1, 1989

By J. E. Marshall

"The concept of employing a project management team to coordinate all aspects of the construction of a new resource development has gained wide acceptance. This team can be formed from within the staff of large mining companies or contracted from major engineering firms and consultants. The mandate of the project managers usually terminates on successful startup of the operation. For frontier mineral developments in the Canadian Arctic or in the developing countries, startup and the initial year of operation represents the period in which the project is most vulnerable to technical, political and managerial problems. A complete change of the management team or the retention of the construction project managers and the resulting cost combined with the breakdown of organizational accountability within the operating staff .are unnecessary management problems.Independent project management services provide the commitment necessary to sustain the continuity of management through all project phases. Efficiency and the ability to make decisions quickly are characteristics of the many successful small mining companies. These qualities are necessary in the project management group, which will be responsible for up to 90% of the preproduction costs.Continuous project management in the construction and operational phases of a mineral development are common in the iron ore industry, but remain anomalous in the base metal, energy mineral and industrial mineral fields.The Nanisivik project on Baffin Island in the Canadian Arctic is used to illustrate the advantages of total project management through construction and operation.Total project management has further potential for foreign interests and financial and utility organizations desirous of participating in the Canadian mining industry, but with no direct involvement in the construction or operating management. Participation agreements in the operating phase of a project can be negotiated to have management fees related to both the production and the profits of the enterprise."

Jan 1, 1980