Search Documents

By S. D. Logan

This presentation describes a lightweight automobile body structure concept developed at DaimlerChrysler to support a high fuel-efficiency vehicle project. This body structure consisted primarily of large thin-wall magnesium castings and resulted in a more than 40% weight reduction with a minimal cost increase over a conventional steel structure while achieving significantly improved structural performance as evaluated through CAE simulations. One concept vehicle was built for the purpose of demonstrating concept feasibility. Several slides showing the prototype build process are presented. The presentation also describes several large thin-wall die casting body applications that are in current production or have been used in recent production automotive applications and identifies areas where further development could improve the chances of a magnesium intensive body structure becoming a production reality at a later time.

Jan 1, 2006

By N. Hosking, M. Nichols

Aluminum alloys are increasingly used for automotive body construction but are susceptible to filiform corrosion or paint blistering in service. Filiform corrosion resistance of two 6000-series aluminum alloys was investigated in this work. Test panels were produced with full automotive coating layers and scribed parallel and perpendicular to the rolling direction. The corrosion exposure comprised an inoculation step with acidified salt solution followed by a 6-week exposure period at 95% relative humidity and either 25°C or 70°C. Greatest corrosion activity was measured on the alloy with higher copper content, AA6111. Higher temperature exposure led to greatly enhanced corrosion activity for AA6111 compared to the lower temperature exposure. The 70°C exposure also led to greater mean corrosion-affected area measurements for the low copper aluminum alloy, AA6022, but the effect was not as stark as that observed for AA6111. Rolling direction affected the propagation direction, and possibly mechanism, of the corrosion effects. Cross-sectional analysis revealed dense corrosion products within the filament, comprising mostly aluminum and oxygen but with traces of chloride and sulphate. Development of varying filament and blister types on a single test panel and the progression of corrosion underneath a filament into the substrate indicate that several corrosion mechanisms can develop on the test panel, testament to the complexity of the corroding surface developed on an aluminum automotive body panel.

Jan 1, 2015

By Peter C. Jones, Wanda M. Carter, David H. Watkinson

"Abstract - Pyrrhotite, chalcopyrite, and pentlandite are the dominant sulfide minerals in the 740 zone of the Kelly Lake orebody (Inco Ltd.), Copper Cliff Offset, Sudbury. Petrographic and quantitative electron microprobe analyses of minerals, from sulfide assemblages and host quartz diorite, of the 740 deposit have revealed three processes that have affected sulfide mineralization and associated sulfarsenide and platinum-group-mineral (PGM) distribution: magmatic, hydrothermal, and tectonic. Accessory, zoned cobaltite, and gersdorffite occur in sulfides as a result of these three processes, and PGM occur dominantly in hydrothermally remobilized and deformed ores. Where PGM are present in sulfarsenides they provided nuclei for sulfarsenide growth. Solitary PGM are orders of magnitude larger than those PGM found within sulfarsenide minerals. Five varieties of PGM occur, michenerite and sperrylite being the most common, with lesser froodite, hollingworthite, and ruarsite.The effect of a deformation is a localized fabric in the ore, revealed by pyrrhotite and chalcopyrite bands; pentlandite porphyroblasts also partially define the foliation. The deformed ore is also characterized by alteration of the adjacent quartz diorite, which produced an alteration assemblage including almandine garnet, Fe-rich biotite, and chlorite."

Jan 1, 2001

By E. V. Konopleva, H. J. McQueen

Steels in high variety have been providing strength and ductility for more than a century mainly through complex heat treatments following hot shaping. The economical and sustainable goal was a steel with the two operations combined through applying knowledge of dislocations and strengthening mechanisms aided by new mechanical and microstructural techniques. Primary hot reversing-mill rolling produced static recrystallization (SRX) between every pass to significantly finer grain size. Hot torsion showed that with lay-on temperature and rate of reduction suited to gradual precipitation of minor additions of Nb, the austenite grains would become highly pancaked; the existence of very fine subgrains along the grain boundaries (GB) could be deduced from tests on stainless austenite. The HSLA strip had to be water-jet cooled immediately to prevent SRX at austenite GB and ensuring complete transformation to ferrite avoiding grain growth after coiling. Confirmation on old mills and successful product led to the design of more flexible mills for wider range of compositions and products. A significant one was auto bumpers that reduced crash damage. More crack-resisting compositions were developed for strip welding into line pipe for arctic oil transport. Lower metal consumption and easier fabrication has resulted in more sustainable welded bridging.

Jan 1, 2015

By T. S. Wanne

Tunnel sealing experiment (TSX) was conducted between 1997 and 2004 in the Canadian URL located in Manitoba. In the experiment, a tunnel was excavated parallel to the maximum principal stress direction, filled with sand and sealed with bulkheads at both ends. It was then pressurized and heated by injecting hot water. The rock mass response was monitored with seismic methods. The main interest in the numerical simulation was the damage formed during the heating phase. The large-scale PFC2D models replicated a central plane- strain section of the TSX chamber. The models captured the first-order phenomena observed in-situ displaying the difference in the damage in the roof and floor regions, respectively. This difference was due to the filling material confinement of about 100 kPa on the tunnel floor, which occurred in the course of the heated experiment.

May 1, 2009

By V. G. Papangelakis, T. Clark, G. Kolliopoulos

Sustainability of the hydrometallurgical industry requires the development of processes for effective water recovery; if process water is recovered and recycled, fresh water intakes will be reduced. Forward osmosis (FO) is an innovative membrane process that promises to recover water from industrial process aqueous streams or seawater with less energy input compared to reverse osmosis (RO) and evaporation; the energy efficiency relies on the spontaneity of the process (no energy input required). The driving force of the process is the osmotic pressure gradient between a dilute feed solution (process water) and a concentrated draw solution. The draw solution is an engineered aqueous solution that contains a highly soluble chemical reagent that is able to osmotically "draw" only water from the dilute stream, through a semi-permeable membrane, leaving behind a small volume of concentrated brine. The draw solute is separated and recovered for reuse, leaving behind water. The main energy requirements of the FO process arise from the separation and the regeneration of the solute chemicals from the diluted draw solution. This work focuses on the evaluation of aqueous carbonated trimethylamine (TMAH:HCO3) as the draw solution and reports recent findings on the separation efficiency of TMA and CO2 from the solution.

Jan 1, 2015

By Nichols. R. S.

"Surface coal mining production from Elk Valley and area in southeastern British Columbia began in 1913. Since 1970, five open-pit mines have been put into production: Westar Mining&apos;s Hanner and Greenhills Operations; Fording Coal&apos;s Fording River Operation; Byron Creek Collieries&apos; Coal Mountain Mine and Crows Nest Resources&apos; Line Creek Operation.ln 1983 these mines produced 14.9 million tonnes of raw coal at an average strip ratio of 4.9 bank cubic metres of waste to 1.0 tonne of raw coal. This is 70% of the estimated 21.1 M tonnes annual capacity .Multiple seams are recovered with truck/shovel and dragline equipment. There is a wide range of equipment types in use with a recent trend toward larger and more mobile equipment.Coal mining in Elk Valley involves advancing along strike in four steps: hangingwall waste removal; seam cleaning; coal recovery; and foot wall waste removal. Each mine is unique in its approach to these four steps but the truck/shovel methods can be categorized into three main groups: seam dips < 35 degrees as at Harmer, Fording and Greenhills; seam dips 35 to 50 degrees as at Line Creek; and seam dips >50 degrees as at Byron Creek. Dragline mining at Fording involves bath waste and coal removal by draglines."

Jan 1, 1984

By Jaime V. Ongpin

"The author will give a capsule history of Benguet Corporation and attempt to identify its operating environment and underlying ""strategy"" until 1974, when the company&apos;s management assumed office. The company&apos;s operating environment and ""interim strategy"" from 1975 to 1980 will be described. The discussion will cover an environmental forecast and define the company&apos;s"" strategy for survival"" for the balance of this century.IntroductionIn December last year, I was asked to deliver a pa per for the management lecture series a t the Asian Institute of Management in Manila. The paper was entitled "" The 1970&apos;s: A Decade of Disaster For New Mining Projects"" . In that paper, it was my task to review the results of new mining projects in the Philippines during the previous decade. The task was not a happy one, for the results themselves were not only unhappy, but disastrous on a scale unprecedented in Philippine history. Out of a total of 17 major mining project s involving an aggregate capital investment in excess o f US $2 billion during the 1970s, only three project s have been profitable, and all the rest have either gone "" belly up"" or are teetering on the very edge of financial disaster.It is in the context of this shocking record of widespread financial dislocation in the Philippine mining industry, (which in varying degrees appears to have been paralleled in virtually every other country in the world where mining is an important sector of the economy) that I address myself tonight to the theme of this symposium. My paper is entitled ""Risk Management Strategy in Mining"" and it is sub titled ""Can Benguet Corporation Survive to Celebrate its Centennial in 2003?"". I have inserted the word ""Strategy"" and added the subtitle, because I wish to make it clear first, that my presentation to you tonight will be focused exclusively on the strategic aspect s of risk management, and second that I will limit myself to Benguet&apos;s own ""in-house"" experience and perspectives on this subject. I would caution you therefore, to consider my views within this restricted framework, and in light of the particular and sometimes peculiar circumstances within which Benguet Corporation operates."

Jan 1, 1983

By S. H. Lucas

"This paper describes the development and application of single-stage fluidized bed continuous ion exchange to the following processes: removal of base metals from mine water; cyanide removal from gold mill waste; uranium removal from sulphuric acid leach liquor; and uranium removal from mine water. IntroductionThe recovery of metals by fixed bed ion exchange has been practiced for many years. However, the operation has been semi-continuous and can only treat clarified liquors. Substantial savings could be made if the operation were continuous, thus reducing the resin inventory, and if the costly filtration and clarification steps could be eliminated. Work has been in progress over the past twenty-five years on the recovery of metals from unfiltered ore leach slurries, heap leach liquors and mine drainage waters containing a small amount of suspended solids. In the case of dilute waste solutions, with suspended matter and high flow rates, filtration is usually prohibitively expensive.Continuous ion exchange operation using fluidized beds has made it possible to reduce considerably the resin inventory and to allow the treatment of unclarified liquors and slurries. The subject has been reviewed on several occasions (1. 2. 3, 4). Although fluidized beds in multi-stage columns are an improvement over previous resin-in-pulp treatment, they have complicated internal structure and I or involved automatic control systems to move the resin stages.Slater and Prud&apos;homme performed studies on multi-stage fluid beds, and concluded that the performance of single, deep fluidized beds of resin with continuous or semi-continuous flow of both phases would be worth investigating, particularly in the case of very dilute metal solutionsoi, A pilot plant was designed and built at CANMET in a cooperative project with Dr. Slateroi. The use of deep fluidized beds of resin (with a large height/diameter ratio) for treating dilute solutions has the attraction of engineering simplicity. Extreme simplicity of equipment design is considered of paramount importance when treating, for example, mine waters at high flow rates, possibly of the order of several million gallons per day. This paper describes the development of the concept of single-stage fluidized bed continuous ion exchange arid reviews the pilotplant development of processes for the treatment of base metal mine water, cyanide waste water, uranium leach liquor and uranium mine water."

Jan 1, 1980

By Jian Li, Robbie McDonald, David Robinson

"The pressure oxidation of sulfide minerals at temperatures above 200°C enables the extraction of base metals, improves the extractability of gold from refractory ores, enables solubilisation of PGEs and can be used to hydrothermally upgrade base metal-containing feeds. Fundamental studies reveal that the solution chemistry (and mineralogy of the solids) during pressure oxidation can be manipulated with outcomes that include (1) increased leaching rates, (2) lower oxygen requirements and (3) the formation of chemically more stable residues. This paper presents examples describing how these outcomes might be achieved based upon fundamental investigations.INTRODUCTION The application of pressure oxidation to the processing of gold ores and concentrates dates back several decades and continues to be the process of choice at operations such as Pueblo Viejo (pyritic gold) which host the largest autoclave of its kind in the world (Barrick Gold Corporation, 2016). Commercial application to the processing of base metals and PGMs resides with long established processes such as the Sherritt process, ore specific applications such as by Noril’sk, at Sepon etc. or has not proceeded to date beyond pilot scale testing (e.g. Phelps Dodge, CESL, Activox, Platsol). Recently there has been significant interest in hydrothermal upgrading options for concentrates including the NONOX and Toowong processes (Rohner et al., 2016; Weidenbach et al., 2016). The latter options suggest directions where sound knowledge of the underlying fundamentals enables novel outcomes and efficiencies to be obtained. It comes as no surprise that investigations similar to those underpinning these developing processes can be traced back several decades. It is not the subject of this paper to provide a historical perspective of the relevant autoclave chemistries but rather, to present some potential opportunities suggested by studies in our laboratories. Topics to be discussed in this paper include (1) control of metal extraction rates, (2) control of iron-residue composition and (3) control of sulfur oxidation and hence acid generation and oxygen requirements. The work described will focus upon the pressure oxidation of a nickel concentrate."

Jan 1, 2017

By R. L. Armstrong, C. I. Godwin, V. M. Kruan

"The Scheelite Dome tungsten-bearing skarn property, central Yukon Territory, is in metasediments in contact with a quartz monzonite intrusion. Contact metamorphism to biotite-muscovite- andalusite hornfels and calc-silicate hornfels is superimposed on low-grade regionally metamorphosed rocks represented by quartz-mica pelitic schist and muscovite-biotite pelitic schist.Metasediments are likely Precambrian in age, even though Rb-Sr whole-rock analyses indicate an early Paleozoic age (511±41 Ma); this apparently too young radiometric age is due to partial loss of radiogenic strontium during regional metamorphism. The minimum age of the quartz monzonite intrusion is Cretaceous at 90.4±2.6 Ma (K-Ar on biotite) and its initial 87Sr/86Sr ratio is 0.7121. The high initial ratio of the intrusion is due to the addition of radiogenic strontium from the metasedimentary country rocks and perhaps an underlying older basement.Scheelite-pyrrhotite-chalcopyrite mineralization occurs in diopside-zoisite skarn pods within the calc-silicate hornfels near the quartz monzonite intrusion. The source for lithophile tungsten is probably the same as for the granitic magma, namely Precambrian sialic basement.IntroductionThe Scheelite Dome tungsten skarn property is within the Mc-Questen map-area (NTS: 115P/16),28 km northwest of Mayo, Y.T., at latitude 63°47&apos; north and longitude 136°15&apos; west. The property can be reached by helicopter or by four-wheel- drive vehicle from Mayo.This paper summarizes the geology of the Scheelite Dome property, which has been described in a general way by Little (1959) and Cathro (1969). Geological mapping and sampling were done by the first author (nee Steffler) during June 1979. Field work was supplemented with detailed work at the Department of Geological Sciences of The University of British Columbia during 1979 and 1980 (Steffler, 1980). Whole-rock chemical analyses were done by Cominco Ltd."

Jan 1, 1982

By L. V. Chugaev

In the course of the hydrothermal refining of copper-nickel products containing covellite, oxidation of Fe2+ ions by the CuS?Cu2+ pair takes place, and iron is precipitated as hematite. Lower copper concentrations in the solution and higher solution acidity lead to the partial oxidation of sulphide sulphur, whereupon hematite is reduced by covellite causing iron to go back in solution. It is demonstrated that in the process of hydrothermal treatment of the covellite-containing solid product in pure water covellite oxidises millerite to polydymite (Ni3S4). Formation of polydymite during the process of refining seems to be due to millerite oxidation both by covellite and the CuS?Cu2+ pair.

Jan 1, 2007

By H. Henao, F. Canales

The present work evaluated the use of copper ore flotation tails as flux in the process of smelting copper concentrates. For this purpose, experimental and simulated liquidus lines were obtained at different ratios of tail/flux. Experimental variables included temperature, partial pressure of oxygen and sulfur dioxide and the conditions of tridymite or spinel saturation. The results indicate the feasibility of replacing the flux by increasing the temperature of the smelting process by 20°C. Results of simulation using FactSage and HSC confirm that the required increase in temperature can be achieved by increasing the flow of concentrate, enrichment of oxygen or increasing the matte grade. INTRODUCTION In the pyro-metallurgical process of copper production, the smelting stage produces two liquid phases, a sulphide phase rich in copper and another composed mainly of oxides called slag. The slag phase is the product of oxidation of the iron contained in the flotation concentrate. The smelting process which is carried out at temperatures of 1250°C, require the addition of silica as a flux and the injection of air enriched in oxygen (Schlesinger 2011). Currently, one of the most important aspects of the mining industry is the minimization of costs, the optimization of the use of available resources and the reduction of environmental impact. Under this context, the use of flotation tails from as a flux in the copper smelting process has the potential of reduced production costs and generate an environmental benefit by reduce the disposal amount of this waste material Regarding the use of copper tails as flux in the copper smelting process, a thermodynamic simulation study using the FactSage software had been reported in the literature (Parra et al., 2011). The results indicated an increase of 35°C in the temperature the liquidus for the equilibrium matte/spinel and a subsequent requirement of energy in the process of approximately 350 [MJ/ton slag]. Given that the calculated viscosity remains in the same order of magnitude, the melting temperature is a more relevant parameter for the evaluation of the use of tailings as flux.

Jan 1, 2019

By Lloyd F. Dunham

"Crucial to the implementation of new computer-based information systems at Sudbury Operations of Falconbridge Limited was a data communications network that would take computing power to the various mine and plant sites. Falconbridge required a capability to provide on-line data entry, inquiry, and reporting capabilities in three geographical areas, six mines, two mills, a smelter, approximately fifty shops, seven warehouses and numerous administrative offices throughout the Sudbury basin.Conventional cabling methods were rejected based on the projected cost of installation of necessary cables; lack of flexibility to meet the changing requirements of the mine environment; and the risk of losing service to an entire area depending on solitary communication lines.Instead, Falconbridge selected and installed a Data Carrier System (DCS) and Packet Switching Communication System from Teltone Limited, Markham, Ontario. This combined system ""piggy-backs"" computer data over voice-grade twisted pair wire, bringing data to the associated PBX equipment. From there data packets are assembled and routed to the central computer site where they are disassembled for entry into the host machine.Falconbridge has been successful in using existing technology to solve communications problems in a difficult environment. Plans for the future of this network will increase its utilization for technical and real time data communications in addition to the business systems workload it now handles. The Computer Services group in Sudbury is confident that the data highway will handle communications traffic well into the future.IntroductionIn late 1984, the Sudbury Operations of Falconbridge Limited undertook a review of their existing business computer systems. The results of this review indicated that there was an opportunity to improve the timeliness and quality of information coming from the existing computer-based systems while achieving an investment payback by undertaking the project. The greatest benefits from this project would be achieved if the computing tools could be delivered to the employees that were the day-to-day users of the data. Falconbridge&apos;s existing business systems were oriented to the batch mode of processing. An alternative solution to using the existing programs had to be found."

Jan 1, 1988

By D. McConchie

The use of Bauxsol? (physically and chemically modified alumina refinery residues) to treat acid rock drainage (ARD), and sulphidic waste rock and tailings, provides new options for managing some intractable environmental problems at both derelict and active mine sites. Treatment of ARD waters using the Bauxsol technology shows that the effectiveness of raw Bauxsol material can be enhanced by including modest amounts of selected industrial minerals or common chemical additives. The type and amount of additive required and the amount of the blend needed to treat the water depends on the initial composition of the water and the target water quality; for some ARD waters, optimum treatment may require one or more changes in the type or amount of additive used. Maximum treatment efficiency can be achieved only when a balance is maintained between the rate of trace metal binding and the rate of change in water pH; adding treatment reagents faster than can be accommodated by the reaction kinetics will not result in more rapid water treatment. This paper presents the results for treating several ARD waters to illustrate the importance of blend selection and treatment procedure. Although treating ARD water is often necessary, this strategy treats the symptoms rather than the cause. The best permanent solution is to treat the sulphidic waste rock or tailings such that they do not continue to oxidise and produce acidic metal-rich leachates; sulphide oxidation needs to be stopped or slowed to a rate that can be accommodated by normal environmental processes. Capping lined impoundments is not a solution because all caps and linings will inevitably fail some time in the future creating a nasty surprise for some future generation. Adding lime is also less than ideal because the lime leaches from the treated material; treatment often appears to be effective for a few years and then fails. Bauxsol technology offers effective alternatives to conventional liming and capping procedures and Bauxsol blend application rates and procedures can be planned to ensure that no acidic or metal-rich water can ever escape from the site. Bauxsol can be physically mixed with the sulphidic mine wastes or it can used to form subsurface permeable reactive barriers, or both. Bauxsol treated waste rock and tailings can be immediately and effectively revegetated. In this paper we present leachate quality and plant growth rate data for several sulphidic waste rock and tailings deposits treated using the new technology.

May 1, 2003

By T. Kagawa

Ever-increasing demands for non-ferrous metals owing to population growth and improvements in the standard of living in the world, under the constraint of limited availability of natural resources, would easily make us imagine that more efficient and sustainable developments in mining and smelting activities are required in the near future with due consideration for environmental concerns. In order to realize the efficient and sustainable development of mining and smelting activities and operations, the following issues are indispensable: (1) to investigate the up-to-date pollution control technologies of mine and smelter, (2) to promote those technologies, (3) to develop technologies which are environmentally friendly. This paper discusses the recent technologies for environmental conservation/prevention and their diffusion in the world, and also the key technologies required for the most desirable sustainable development.

Jan 1, 2007

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Preg-robbing may arise from natural carbonaceous materials in the ore. Several mechanisms have been proposed in the past decades including a physical sorption process by the carbonaceous matter, or via the reduction of aurocyanide at the mineral surface (Abotsi & Osseoasare, 1986; Afenya, Osseoasare, & Abotsi, 1983; Tan, Feng, Lukey, & Van Deventer, 2005). Nevertheless, the mechanisms of preg-robbing remain poorly understood. Understanding the nature of the preg-robber is of practical importance for the selection of a suitable treatment process. Fine carbon particles in the ore have been recognized as preg-robbers due to their similarity to the activated carbon used in the carbon in leach (CIL) or carbon in pulp (CIP) processes. Previous research has illustrated that the activated carbon (also referred to as amorphous carbon in some literature) has a much higher absorption ability than pure graphite with high crystallinity (Adams & Burger, 1998). Adams et al (Adams, Swaney, Friedl & Wagner 1996) concluded that carbonaceous matter is largely responsible for the overall preg-robbing capacity of a given ore. However, the mechanism of carbon preg-robbing was still not clear mostly due to the complexity of amorphous carbon and its behavior in different solution matrices, and at different pH and temperature (Adams, 1990, 1993)."

Jan 1, 2017

By Alan J. Wianwright

Introduction ??New world-class Upper Devonian porphyry Cu-Au system located in south Mongolia ??6.5 km NNE-trending mineralized corridor ? 4 discrete deposits ??Southern Oyu deposits: Chalcopyrite, deposits: bornite ??Hugo Dummett: Zone: Hypogene chalcocite in addition to chalcopyrite and bornite ??Total resource exceeds ~2 Gt@ >1% Cu, >0.25 g/t Au (0.6% Cu equivalent cut-off) (Ivanhoe Mines press release, 2005)

May 1, 2006

By J. Borlee, F. Sorrentino, A. Fleischanderl, M. Gimenez, W. Gebert, U. Gennari

Large quantities of solid by-products are generated by the steel industry and other important activity sectors in Europe (power plants, car dismantling companies, urban incinerators) with no or very limited potential for direct recovery. In the frame of a multi¬national project supported by the European Union, a consortium has been created to develop a treatment process able to turn these by-products into valuable metallic and mineral products. VAI has been responsible for the design, erection and start-up of the pilot plant for the new metallurgical process and for the execution of the test campaigns, with the targets defined together with the partners. Up to now, 9 campaigns comprising 60 heats have been performed successfully. By-products from C-Steel and stainless steel plants, as well as fly ash and auto shredder residues, have been used and defined products such as hydraulic binders for cement, metallurgical powders for De-S practice and recycled metal phase have been produced. The mineral products were positively assessed under industrial conditions. Results from cement tests and secondary metallurgy are reported, as well as a detailed characterization. The economic value of the products, credits from avoiding dumping and significant savings on CO2 emissions make the new process economically very attractive.

Jan 1, 2004

By K. Tsuchihashi, A. Kishimoto, T. Uda, Y. Kado, S. Maruyama

We recently proposed a continuous production process for titanium metal with some experimental results. In the process, titanium tetrachloride is reduced by Mg in the presences of Bi to form a Bi-Ti alloy at 900ºC. At this temperature, the obtained alloy is liquid and allows for the continuous removal of product and heat from the reaction vessel. The obtained Bi-Ti alloy was vacuum-distilled at 1000ºC for 24 hr, and 98 at % (92 wt %) titanium, which was easily crashed to powder, was obtained. Bi solvent was selected because of the highest titanium solubility at 900ºC and the moderate vapor pressure among the candidate metals (Bi, Sn, Pb, Zn, and Sb).

Jan 1, 2014