Search Documents

By W. Petruk

A study was undertaken to determine whether interrelations between mineral grains affect ore breakage during grinding, and to establish a correlation between ore breakage and mineral liberation. A base metal ore from the Brunswick No. 12 deposit in New Brunswick was ground for different periods of time in a laboratory ball mill, and both the unbroken ore and the ground products were analysed by image analysis. The results show that the mode of breakage is strongly influenced by the behaviour of pyrite. Similar size distributions were obtained for material from the 15 minute grind in a laboratory ball mill, for the grinding circuit discharge from a commercial mill, and for pyrite grains in the unbroken ore. This similarity indicates that a 15 minute grind breaks poorly bonded pyrite grains along grain boundaries, and represents the limit of easy breakage for the ore. Such a grind liberates both large separate grains of ore minerals and poorly bonded mineral grains that occur in interstices among pyrite. On the other hand the 15 minute grind does not separate moderately bonded mineral grains nor release moderately bonded interstitial minerals from pyrite; a 45 minute grind in a laboratory ball mill is required. It is assumed that, for Brunswick No. 12 ore, a 45 minute grind in a laboratory ball mill is equivalent to regrinding in a commercial mill. Grinding beyond 45 minutes in a laboratory ball mill breaks the ore by fracturing pyrite across grain boundaries and by chipping grain edges. Such intense grinding does not markedly increase sphalerite liberation from Brunswick No. 12 ore, because most of the sphalerite that can be released was liberated at the 45 minute grind. In contrast the intense grinding increases galena liberation because a significant proportion of the galena occurs as minute inclusions in pyrite. These findings show that ore breakage and coincident liberation depend upon size distributions, intergrowths, and mode of occurrence of the minerals in an ore.

Jan 1, 1988

By Claude Bazin, François Robichaud

The control of the operation of a semi autogenous grinding mill is mainly based on power and bearing pressure measurements. Image based sensors can provide on-line measurements of the size distribution of the ore feeding a SAG mill allowing the control of this variable that impacts the operation of this equipment. This paper investigates the potential of using the information from such type of sensor to maintain a SAG mill feed target size distribution by manipulating the speed of the ore extractors below an ore stockpile. A PID and adaptive predictive controller for the size distribution are studied using a simulator for a stockpile and the equipments used for ore withdrawing from the pile. The proposed controller is found to give a good performance while remaining easy to tune.

Jan 1, 2014

By J. A. Meech, C. A. Harris

"The application of control theory in mineral processing is more difficult than in other industries because of the complex nature of the unit processes involved and because of problems with accurate on stream measurement of process variables. Conventional control is based on proportional, integral and derivative functions of a continuously measured error term. Computer control can enhance these actions by incorporating logical routines to switch from one relationship to another. The success of this logical approach depends on our understanding of the process dynamics and the stability of the process and model under all conditions. Typically the model does not apply at all times in mineral processing because of frequent and unmeasurable changes in the ore parameters.Recent advances in the theory of fuzzy sets have led to the application of this science to process control. Fuzzy Logic can be used to develop heuristic or rule-of-thumb controllers with the strategy based on the actual operating practice of experienced plant operators. Control action has increased flexibility through the adaptation of human reasoning. Acceptance of the control system by operating personnel is significantly higher because of their participation in its formulation. The requirement of an exact model is not essential.A heuristic controller has been designed and tested with a computer simulation model of a secondary crushing plant. The results of this study are discussed and future applications of this control technique to other mineral processes are suggested. IntroductionThe application of control theory in mineral processing is more difficult than in other industries because of the complex nature of the unit processes involved. Mineral processes typically are characterized by non-linear relationships between input and output variables. Many of these variables cannot be monitored accurately on-stream and so long time lags on the measurement loop are features of the system. The processes, themselves, often have long time-varying responses while the process loads fluctuate significantly on a short-term basis.Attempts to control these processes have led to the formulation of mathematical models to describe each unit activity. Adaptive techniques have also been tried to compensate and account for process changes and vageries. These approaches are mathematically rigorous so that their complexity and precision limit their usefulness when applied to ""vague"" processes."

Jan 1, 1987

By M. Fairman

The effect of welding speed on the microstructure of friction stir processed (FSPed) AZ31B-H24 magnesium alloy was studied using light microscopy, image analysis, and microhardness tests. The grain size of the magnesium alloy was observed to increase after FSP from about 3.5 µm in the base alloy to about 8 µm in the stir zone. The aspect ratio decreased from 1.60 to 1.55 towards the center of the stir zone. The changes in the grain size and shape caused the microhardness of the samples to drop significantly across the FSPed region from 75 HV in the base alloy to below 55 HV in the stir zone. Decreasing the welding speed increased the grain size due to a greater input of heat energy. The faster heating rate due to the lower welding speed caused a deeper penetration of the annealing effects of FSP. It was also observed that the annealing effects caused by FSP were less pronounced with increasing distance from the interface between the sample and pin tool shoulder. The Hall-Petch type relationship of the micro-indentation hardness as a function of the grain size was observed to hold true after FSP.

Jan 1, 2007

By Robert B. Parsons

"Effective January 1, 1990, mines in British Columbia are subject to a new provincial mining tax statute, the Mineral Tax Act. Under this Act, mines are subject to a two-tier tax system, with a minimum tax payable on ""net current proceeds"" and a higher tax paid on net income. For many mines, the present value of tax paid under the new rules should be comparable to the amount paid under the old rules. Earlier cash payments could pose difficulties, particularly for smaller mines, but existing producing mines could benefit in the short-term.IntroductionEffective January 1, 1990, British Columbia has replaced the provincial mining tax regime under the Mineral Resources Tax Act with a new system under the Mineral Tax Act. The new rules borrow some ideas from other provinces (New Brunswick's two-tier concept, and Saskatchewan's indexed costs) with a view to levying a tax that is fairer to both the producer and the province."

Jan 1, 1990

By D. E. Salman, R. R. Maclachlan, R. J. Barclay

"There is a considerable resource of data for spherical charge cratering, both as single charges and in row-of-charge geometr(1). The data are. however, based on cratering performance to a single free planar surface.In practice. the more common circumstance involves an angular surf ace geometry. such as occurs at the toe of a bench or the wall of a stope. It is for the purpose of investigating this circumstance that the described test work was conducted.The test objectives were: (1) to observe the change in single-charge cratering performance between planesurface and angle geometry; (2) to identify the optimum performance of single charges cratering to a plane surface. cratering from a bench sub-grade position and cratering from a condition of zero sub-grade or stope wall geometry; and (3) to observe the performance of row-of-charges cratering to an angular surface at various row burials and spacing. The row charge burial and spacing dimensions were to be expressed in simple numerical multiples of single-charge depth-of-burial data."

Jan 1, 1981

By H. M. Roscoe

Fifty per cent. increased lump coal production and at the same time a reduction of from 20 to 40 per cent. in explosive consumption. These results were achieved by the use of the rock-dust cartridge method of stemming shots in the Ruhr coal mines, as announced by Dr. Alfred Stettbacher in the September 1923 number of the Explosive Engineer. Immediately, the explosive and the coal-mining industries on this continent became intensely interested. Considerable experimental work has been carried on in a number of American and Canadian mines during the past year, by which our engineers have become assured that the use of rock-dust cart-ridges for stemming shots increases the efficiency of explosives and promotes safety in coal mines.

Jan 1, 1924

By PETER O. SANDVIK

The Cargill deposit, located 32 km south west of Kapuskasing, Ontario, was discovered by International Minerals and Chemical Corporation in 1975 and has been evaluated through an extensive program of drilling, chemical analyses, metallurgical tests and engineering and economic studies. The Cargill alkalic complex, comprising mainly carbonatite and pyroxenite-amphibolite rocks, was intruded into the rift system of the Kapuskasing magnetic-gravity high. Weathering and leaching under assumed temperate to cool climatic conditions plus faulting, shearing and/ or initial petrographic variations within the carbonatite developed a small, locally confined karst system. This resulted in a thick enriched leached carbonatite zone capped by troughs and sinks, and filled with a residuum of apatite, goethite, clay and other minerals. Residuum thickness ranges from nonexistent on ridges to 170 m in troughs and sinks. Apatite values are 5 to 15% in fresh carbonatite, 20 to 40% in leached carbonatite and 20 to 98% in residuum. A tentative open-pit mine designed for preliminary feasibility studies is estimated to contain 62.5 million tonnes averaging 19.6% P20 5.

Jan 1, 1984

By F. T. Manns, G. Harper

"The Swayze gold mine is an Archean vein deposit in northern Ontario. The veins are superimposed on a conjugate joint system and are contained within an anastomosing alteration envelope in a metadiorite body. Reserves were estimated on the basis of fire assays of channel samples and car load samples from underground mine openings, surface and underground diamond drilling and surface trenching. A semi-variogram constructed from channel samples along one of the drifts yielded a horizontal, regionalized influence of approximately 9.0 m. Common industry practice has been to use 6.1 m for similar deposits in Ontario. Proven ore was defined from underground openings. The maximum extrapolation distance for proven ore along strike and dip from a data point is taken to be 6.1 m. Probable ore is extrapolated 7.6 m from a data point in a mine opening or from a drill intersection. Possible mineralization is based on geological continuity one-half the distance to a neighbouring data point.The mineral inventory estimate of 1.45 million tonnes at a grade of4.8 g Au/tonne gives an excellent outline of the geology of the deposit. The deposit contains 313 000 tonnes of ore reservesat a fully diluted grade of6.9 g Au/tonne. These figures include dilution for several reasons: (I) a 2.1 m mining width is used rather than the more typical 1.5 m width to allow for over break because of the shallow dip of some vein zones; (2) over break is allowed for adjacent to major unmineralized dykes; and (3) grams of gold are deleted from estimates to allow for the mining of unavoidable minor dykes.A personal computer with off-the-shelf software was used to compile 712 geologically defined ore blocks and sort them into a number of revealing categories. The computer was used to perform grade sensitivity tests, as well as to evaluate depth potential. Hopefully, the reiterative aspect of the method has randomized the errors and helped to cancel their effects."

Jan 1, 1987

By J. F. Wright

The cold, or Kississing, Lake area in northwestern Manitoba was the scene of considerable prospecting and mining activity last summer. At the Sherritt-Gordon property, four diamond drills were at work exploring a large deposit of copper and zinc ore, and underground work was in progress on this deposit from two shafts. Some preliminary diamond drilling was completed in five other deposits, and surface exploration work was in progress at a dozen or more additional localities where copper and zinc sulphides were known to be present. Many prospectors visited the area and spent some time in search for new deposits, but apparently few discoveries were made; consequently, last autumn some returned a little disappointed in the area as a prospecting field. Although many visited Cold Lake area last summer in the search for mineral deposits, it should be emphasized that this new prospecting field is a very large one, and that to date only a small proportion of the ground has been examined, except in a very general way. Within the past 18 months, a village of several dozen cabins, and with a population of l00 or more persons, has sprung up on the shore of Cold lake, just west of the Sherritt-Gordon mine. This at present is the business centre of the area, and two banks, a post office - named Kississing by the Postal authorities - a Mining Recorder's office, as well as several restaurants and stores carrying a fairly complete stock of groceries, dry-goods, and general prospecting equipment, are already established.

Jan 1, 1929

"This paper describes an alternative method of vehicle control which uses a micro-processor to control the field current and armature voltage concurrently. The field tests carried out and the conclusions drawn from the basis of the paper.IntroductionIt is generally accepted that the main obstacle to a greater use of electric vehicles is the relatively poor range and performance when compared to alternatives such as diesel and petrol-engine vehicles. Much effort has been applied to the problem of increasing the energy storage density of batteries and considerable improvements are now being reported.Improvements in the efficient use of the stored energy, although unlikely to achieve the necessary increase in range and performance for a widespread acceptance of electric vehicles, can nevertheless make a useful contribution. Because the improvement in efficiency is achieved by a reduction in losses, it follows that the temperature rise in drive-train components is reduced. These advantages, coupled with the increasing cost of energy, make improvements in the efficient use of the stored energy desirable, if not absolutely necessary. To achieve this with the large and rapidly varying loads encountered during the operational use of a vehicle will require a more flexible system of control than that provided by the current limit. This paper describes an alternative method of control which uses a micro-processor to control the field current and armature voltage concurrently.The value of these parameters is selected to supply the power demand at the motor shaft, with the minimum losses in electrical transmission, thus increasing the efficiency with which the stored energy is used."

Jan 1, 1982

By G. Vibert Douglas

IN a previous paper by Douglas and Gillies (1), a simple field test was given for gold. Later work by the present writers, and by others who have kindly written to us, shows that the test is not as satisfactory as it was hoped. In many cases, the gold mirror is completely obscured by a dense precipitate which, up to the present, it has been found impossible to remove. After many attempts, we have temporarily given up the iodine test and have been working on a simple pyridine reaction based on the work of Putnam, Roberts, and Selchow (2): The ore to be tested is ground to a fine flour. Place half a gram of this powdered ore (an amount that will cover a Canadian ten-cent piece, not heaped) in a six-inch test-tube and add 5 c.c. of aqua regia. The aqua regia. should be made up on each occasion, using four parts of hydrochloric acid and one part of nitric acid, both concentrated. Shake the solution in the test-tube for about one minute and allow to settle until dear. The rime to settle may be 30 to 60 minutes. When dear, a drop of the solution is with-drawn with a fine, dean eye-dropper or capillary tube and placed on à small glass plate. A slide such as is used for mounting rock sections is suitable. Now place an equal sized drop of pyridine solution on the plate beside that of the aqua regia solution to be tested. The pyridine solution, containing nine volumes of hydrogen bromide to one volume of pyridine, can be made up in advance and carried in a glass-stoppered bottle. Join the two drops with a glass thread or fine, dean stick, and allow the merged drops to stand undisturbed. I t is well to place the slide on a piece of white paper so that the presence of the crystals which may form can be easily seen. The time for their formation will vary with the amount of gold present, but the slide should be allowed to stand for at least 30 minutes before negative results are reported. A hand lens of at !east ten magnifications is essential. If gold is present, minute red crystals will form around the margin of the drops as these drops slowly evaporate.

Jan 1, 1938

By L. Byszynski

The results of a three month evaluation of the application of EMEW® technology at the KGHM Glogów II Smelter tank house bleed stream are presented. The current, conven¬tional electrolyte decopperization process has some limitations, including: only a fraction of its production is commercial grade cathode copper, significant operating costs, low current efficiency, low current densities resulting in low copper depletion rate, and arsine gas and sulphuric acid emission. The EMEW® cell technology developed by Electrometals Technologies Ltd. can overcome many of these limitations. Tests were performed on a pilot EMEW® installation comprising 30 cells at ambient temperature on electrolyte bleed, using current densities between 100 and 600 A/m2 , with copper concentrations between 45 and <1g/dm3. Results showed that a high grade copper can be obtained to the level of 7 g/dm3 of copper concentration in electrolyte. The use of EMEW® technology allows the direct and efficient recovery of over 85% of the copper contained in the bleed electrolyte. Glue & thiourea addition were tested in order to improve the parameters of the copper depletion process. The behavior of Arsenic and Bismuth was observed and a means for their elimination from the system proposed. On-line copper concentration monitoring is proposed to improve control and performance.

Jan 1, 2007

By Jochen Petersen, Alison Lewis, Cledwyn Mangunda

Run-off and waste water streams high in dissolved metal content are generated in all mining operations. The metals pose a threat to life due to their persistent bio-accumulative toxic (PBT) characteristics. Hence, there is a need to treat mine waste water effectively. Lime precipitation is the technology of choice through which Fe, as the major metal species, is removed as Fe (III) oxyhydroxides with other metals co-precipitated and/or adsorbed. Sulphates are removed as gypsum or incorporated into the Fe phases. The resulting sludge has poor dewatering characteristics and is deposited in landfills, with an inherent risk of returning the Fe back into the water cycle through leaching. This study seeks to understand the mechanisms behind the formation of this sludge in terms of product quality. The relationship between process conditions and product characteristics has been investigated through exploring the effect of Fe (III) concentration on the precipitate product characteristics (particle size distribution (PSD), size, morphology and structure) and quality (in terms of filterability, settling ability, etc.) in a simplified system. Neutralisation of acidic synthetic aqueous Fe (III) sulphate streams containing 50, 400 and 800 mg/L Fe(III), respectively, was effected by mixing it in a continuous stirred tank reactor (CSTR) with dissolved calcium hydroxide for pH control at a residence time of 15 minutes. Precipitate samples analysed for morphology and PSD, using nanoSEM and Zetasizer respectively, showed a general decrease in PSD and zeta potential with increases in feed Fe (III) concentration. These results were used to infer the particle size enlargement mechanisms of Fe (III) oxyhydroxide precipitates under a given set of operating conditions. Preliminary product quality results indicate that a high concentration (800 mg/L) leads to the rapid formation of metastable precursors with poor product quality, whilst a low concentration (50 mg/L) leads to formation of thermodynamically more stable precipitates with good product quality. The approach demonstrates a potential route forward in terms of linking operating conditions to the attainment of desirable characteristics rather than specific precipitate phases which are difficult to identify.

Jan 1, 2016

By F. Logsch, H. Pempel, J. Markowski, P. Ay

"Due to the European Directive 2000/53/EC on end-of-life-vehicles, from 2015 on more than 95% of car materials have to be recycled. In order to recycle the materials back into the economic cycle, it is necessary to produce products with high quality and purity.Plastic components in cars, which are coated with metals by vapour deposition or electroplating, have a wide circulation (e.g., as cladding panel or trim strip for interiors and exteriors). In the end-of-lifevehicle recycling process, these plastic-metal composites are not considered in usual technologies (car shredder) and are not separated from Automotive Shredder Residue. These parts can be separated by optical or HF-detection sorting and then introduced to a specific treatment.Experiments with a specially developed bioleaching configuration showed that the thin coatings, which consist mainly of copper, nickel and chromium, can be removed efficiently from the polymer base materials by a bioleaching solution with Acidothiobacillus ferrooxidans as a leaching agent. The solution used was produced in special fermenters with a 9K-nutrient salt media. During the bioleaching process at 35°C maximum temperature, most of the copper is dissolved and the other metals accumulate as metal sludge. The bacterial cultures based on A. ferrooxidans are robust and resilient.After a 48-hour bioleaching period while the composites were stirred regularly with ventilation, the plastic particles were completely free from metallic coatings. The metal components are separated for further use: undissolved components (mainly Ni and Cr) are separated by decantation of the solution; dissolved copper recovey is carried out by cementation of copper. The cementated solid contains ~98% Cu, along with small amounts of other metals.With the bioleaching process, good separation and re-utilization of the metallic coatings is possible. The cleaned plastic parts were prepared by compounding for new applications with injectionmoulding."

Jan 1, 2016

By Naoki Takada, Dae-Sung Cheon, Minoru Sato, Masaji Kato, Manabu Takahashi, Weiren Lin

"The permeability and specific storage of rocks and sedimentary layers deep underground are critical parameters for issues related to the buried evaluation of natural gas and oil, CO2 aquifer storage, various kind of waste storage and so on.The Shirahama sandstone of the Wakayama prefecture, Kii peninsular in central Japan, consists mainly of quartz grains with no cracks and rock fragments that are aggregations of various kind of minerals. The quartz grains have an average size of about 150 micron. The pre-existing pore sizes were distributed dominantly at approximately 1 micron, and the total porosity was about 13%.During the hydrostatic compression test, we measured permeability of Shirahama sandstone by Transient Pulse test for three mutually perpendicular directions. Permeability of Shirahama sandstone remained fairly constant while increasing the effective confining pressure. Permeability anisotropy was observed slightly in the normal and two parallel directions to the bedding planes.We used micro focus X-ray CT with high resolution of 10 micron to visualize and measure the voids space information in Shirahama sandstone. Three-dimensional data were obtained in the intact and stressed sandstone simultaneously. Pore structures and grain boundaries were clearly distinguished. Pore closure and grain movement were clearly observed with increasing confining pressure. Micro focus X-ray CT is an effective tool to visualize and measure the geometrical information in rocks.Three-dimensional medial axis (3DMA) method was introduced to quantify the flow-relevant geometric properties of the voids structure in Shirahama sandstone using µfocus X-Ray CT data. The number of connecting path between two faces, tortuosity and the shortest path distribution within an arbitrary region of Shirahama sandstone specimen were analyzed. Geometrical information on the number of connecting path shows reasonable correlation between permeability anisotropy and mutually perpendicular directions normal and parallel to bedding planes. In addition, we introduced numerical simulation of fluid flow of pressurized Shirahama sandstone by LBM, to discuss the permeability change caused by pressurization on effective confining pressure. We obtained the detailed distributions of fluid pressure and fluid velocity in relatively narrow voids space more than 10 µm. It was confirmed that pressurization effect on permeability caused by the decrease of the connecting path and the shortest path between arbitrary faces, and then caused a complex condition on fluid pressure and fluid velocity."

Jan 1, 2015

By Douglas H. Silvey

"The historical transformations in fire -resistant conveyor belt compositions in the past 20 years have been influenced by factors of material cost, changing flame and burn test requirements, material replacements, adhesion and oil resistance considerations, increased responsibility and legal liability. Specifically, this has resulted in a swing from neoprene-cotton belts to S.B.R. blends and synthetic fibre carcasses, and tighter quality control and documentation of test data.Flame dynamics are discussed and the function and performance of the multiple types of flame-resistant additives in the flame front are presented. Specific flame and burn test requirements are described. The belt manufacturers&apos; requirements and criteria in selecting the types of flame-resistant additives are presented.The author will describe the composition of the types of flame-resistant compounds used in a practical production, the belts that are available on today&apos;s mark et and future developments in requirements that may further transform the composition of fire-resistant belts.IntroductionThe historical transformations of conveyor belt compositions in the past two decades have been based on factors common to those leading to changes in man y organic compositional products. These factors are material cost, new materials, the customer&apos; s changing requirements, government regulation s and increased manufacturer&apos; s liability.As a basis for understanding the product, I will provide a brief breakdown of the conveyor belt composite. Figure 1 represents a cross section of a typical belt. A skim rubber coats each fabric ply of the belt carcass and is of a different rubber composition than the outside layer of rubber which forms the cover. This outside cover layer is designed to protect the belt from environmental factors such as heat, oil and abrasion, and other factors involved in the service condition s under which the belt will operate. In the case of fire-retardant belt s, both the skim coat encapsulating the fabric plies and the outer cover must contain sufficient fire retardancy to overcome the contribution to burning of the decomosition products of the fabric."

Jan 1, 1982

By Todd S. Harris

"IntroductionThe western region of North America has long been considered a dynamic market supporting such diversified industries as lumber, agriculture, cement, and electronics. In recent years however, the region has also been the focus of a great deal of activity in the extender and filler mineral s business from companies seeking to position themselves to take advantage of the large demand for these materials both here and abroad.Extender and Filler MineralsExtender and filler mineral s include 15different products used in numerous end uses. The nine most important extenders and fillers are listed in Table I. These products range in price from under $50 a ton to over $4,000 a ton and basically represent the following three different types of minerals:Particulate products-Calcium carbonate; Kaolin; Silica.Platy minerals-Talc (Montana, Canada); Mica.Fibrous minerals-Talc (California, Eastern U.S .A.);Wollastonite.What distinguishes these products from other industrial minerals? For one thing, an important feature of extender and filler minerals is that they are used primarily in such consumer non-durable good s as paper, paint, plastics, sealants, and rubber which traditionally do not react as violently to swings in the economic cycle. In addition, these minerals are sold principally on key physical properties, usually brightness, particle size and shape, oil absorption, and hardness. As part of the physical minerals segment of industrial minerals, extenders and fillers are traditionally the most stable group and typically the most profitable. Studies by C.H. Kline over the past decade on extender and filler minerals has revealed historic average profitability (expressed as a percentage on sales) nearly double that of most other industrial mineral s.The demand for these minerals in the western region (Fig. 1), closely follow s the areas of greatest population concentration. These markets include pulp and paper, mainly in the Pacific Northwest, and paint, around Los Angeles and San Fran cisco. Other significant markets for extender and filler minerals in western North America include joint cements, carpet backing, and plastics, mainly PVC pipe."

Jan 1, 1986

By S. Brophy

Controlled Short Circuit ? Metal Inert Gas (CSC-MIG) welding is a process that can be referred as a "Cold Welding" technology. The CSC process is based on accurate control of the welding wire position, thus the mandatory requirement for the automation of the process. One of the main advantages of the CSC-MIG process is the rapid solidification of the deposited material, resulting in weldments displaying low porosity contents, and enabling the joining of thin sheet materials. These characteristics render this process an ideal one for freeforming of components, where rapid solidification would be efficacious. This presentation will focus on the progress made towards the freeforming of Al-based components in the NAIN laboratory at McGill University. The relationship between the filler metal used, freeforming (deposition) parameters, resulting microstructure and mechanical properties will be presented.

Jan 1, 2011

By J. N. Hilton, D. Moffett, E. Barnes

"A recent pilot-plant program carried out at Rio Algom&apos;s Quirke uranium mine at Elliot Lake, Ontario is described. The goal of the research was the production of tailings basin effluents which were low in total radium-226. The process tested involved precipitation of radium with barium chloride and sedimentation in plastic-lined settling ponds. Adjustment of the tailings basin overflow from its normal value of pH 9.5 by addition of sulphuric acid to about pH 7.5 was found to give approximately a five-fold improvement in total radium-226 removal. A five-month demonstration test resulted in an effluent with a mean total radium-226 activity of44 pCi/L after 2.5 days settling time and 29 pCi/L after 5 days. The results from the demonstration program are used to propose a schedule of achievable total radium-226 activities where precipitation and sedimentation are employed. The maximum suggested values for 5 days nominal settling time are: 30 pCi/L in an annual mean, 45 pCi/L in a monthly mean. 60pCiIL in a weekly mean and 80 pCi/L in any single grab sample.IntroductionRadium-226 has been removed from effluents at the Elliot Lake uranium mines since the introduction of the first barium chloride treatment system in 1965. Current practice, which has changed little over the years, consists of radium-barium sulphate precipitation by the addition of a low do se of barium chloride to the clear overflow from the tailings basin(l·2l. Provision is made for the precipitate to settle in large natural or constructed ponds and lagoons. The residence time in these ponds, which depends on the site, ranges from 3 to 35 days, with varying degrees of efficiency being achieved."

Jan 1, 1981