Search Documents

By W. J. Jenner

"Introduction The Saskatchewan Power Corporation is a provincial crown corporation which operates under a mandate to supply all customers within Saskatchewan with electricity and natural gas. The Saskatchewan Power Corporation operates two coal mines within the province of Saskatchewan. The Souris Valley Mine is located a few miles south of the city of Estevan and produces approximately 300 000 Mg of lignite per year. The lignite is shipped about four kilometres by truck and burned at the 882 MW Boundary Dam Power Station, also owned by the Saskatchewan Power Corporation. The Poplar River Mine is located just south-west of the town of Coronach, Saskatchewan which is some 190 kilo metres west of Estevan. This mine produces approximately 1 675 000 Mg of lignite per year. The lignite is shipped seven miles by rail to the Saskatchewan Power Corporation's Poplar River Power Station. The Poplar River Mine is the sole sup plier of fuel to the Poplar River Power Station, which generates some 300 MW of electrical power. A second 300 MW unit is due to be commissioned at the Poplar River Power Station in mid-1983 and the Poplar River Mine will have doubled its capacity to approximately 3 350 000 Mg per year by that time: Souris Valley Mine Geology The Souris Valley Mine extracts lignite from the Estevan seam of the Ravenscrag Formation. This formation is of Tertiary age and was deposited during the Paleocene Epoch. The Ravenscrag Formation outcrops throughout southern Saskatachewan and all coal mined in the province occurs in this formation. Ravenscrag sediments are deltaic in origin and are composed of a series of fine sands, silts, clay and lignite deposits."

Jan 1, 1985

By Karl Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1ms increments up to 1500ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger.  The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits. Conclusions and Future Work 1] The HMX based electronic initiation system permits bottom in-hole delaying in ground temperatures above 80°C (175°F). As compared to top priming and surface delaying, in-hole bottom delaying is known to improve floor quality, muckpile fragmentation uniformity and reduce oversize. 2] Field evaluation of the HMX initiation system at the Lihir Mine is continuing. 3] Work on the next generation of the HMX initiation system is underway and will bring with it expanded application range and flexibility. 

Oct 1, 2024

By V. W. Shtenko, B. J. Ennis, P. H. Bridge

"The northeastern region of British Columbia contains large quantities of high-quality metallurgical coal. To market the coal, it was necessary to provide the required infrastructure which included rail access. This paper presents the role of the British Columbia Railway in the northeast coal development.In 1976, B.C. Railway undertook to study two main routes, one originating at Chetwynd and the other at Anzac, both located on the main line, north of Prince George. The routes studied are briefly described, detailing the methodology and engineering analysis carried out to permit the selection of a single route that would be the most cost effective, taking into consideration the construction, maintenance and operating costs. The operating parameters, track and grade standards, anticipated tonnage, construction costs and the final route selected are also presented.Pre-engineering analysis and studies of the route selected originating at Anzac, known as Tumbler Ridge Branch Line, and which commenced in 1977, were concluded in 1978. New mapping was developed to a scale of 1:2000 with good vertical and horizontal control. Based on the mapping data, terrain analysis, and designs developed, an estimate of construction costs and schedule of work was developed.Authority to proceed with the final design and construction was provided in December 1980, with the first shipment scheduled for December I, 1983. Final designs of all structures are discussed, including schedules, cost to completion, and control systems utilized. The decision to electrify the Tumbler Ridge Branch Line and related topics are discussed, with a brief description of train operations. The present status of the project is also presented."

Jan 1, 1983

By Steve Scott

Green Economy Toyota Prius Hybrid contains about 50 kg of copper. All-electric cars have about 100 kg of copper. From where will all the copper come? Wind turbines have 1 metric ton of copper China is building 221 cities of 1 million people by 2025 (13 cities per year from 2008) = 10 New Yorks. The Greater Toronto Area has 5.6 million people, so a new GTA every 22 weeks!

May 1, 2013

By Craig Faulkner

Discharge cones for large Semi Autogenous Grinding (SAG) and Autogenous Grinding (AG) mills are subjected to high wear as significant volumes of ground ore and slurry exit the mill. With the larger diameter mills of 32ft to 40ft in size becoming the norm, very high, concentrated wear is highlighting the limitations of conventional discharge cones and frequent changes are subsequently required. This paper outlines the advances made in the design of the Bullnose discharge cone. Superior wear materials to increase wear life over conventional rubber or chrome-moly steel discharge cones and the introduction of key design features to reduce reline times and improve fit and safety during installation, offer significant opportunities for the mill operator. Collated from multiple case studies, the wear data and reline history from 2004 to present clearly illustrate the way in which superior component longevity has reduced the frequency of relines over the life of the product to increase mill availability and effectively increase the tonnes milled in a period.

Jan 1, 2012

By David E. Pearson

"Western Canadian coking coals are located in the Rocky Mountains arid foothills of British Columbia and Alberta. They are typical of non-marine coals, characterized by total sulphur contents of less than one per cent and with ash contents of 10-30 weight per cent. This mineral matter is composed principally of kaolinite and quartz.The petrographic compositions of most of the coking coals which constitute the 2.065 billion tonnes of British Columbia's measured reserves, and the compositions of the metallurgical coal currently exported from Alberta, show them to be rich in the inertinite macerals, macrinite, fusinite and semifusinite. When the mean maximum reflectance of vitrinite in oil/Romax) is used as the coal rank parameter, this high inertinite content is reflected in the lower volatile-matter yields, but the relatively inert character is also displayed by lower free swelling indices (PSI), lower maximum dilatations, lower maximum fluidities and lower coke strengths than other coals of the same rank, but richer in the reactive macerals, vitrinite, exinite and semifusinite. Despite these reduced values in the so-called caking tests, inertinite-rich coals produce strong coke.A system of classification of coking coals is introduced which is based on rank, as indicated by Ro max, and either petrographic composition, maximum dilatation, maximum fluidity or, to a lesser extent, PSI and volatile-matter yield. Six principal coal groups can be distinguished among coking coals using this versatile classification. Inertinite-rich coals are assigned to the Keystone Group (GI), Balmer Group (G3) or Moura Group (G4), each group being named for a coal typical of that population ofcoals. Reactive-rich coals are assigned to the Pittston Group (G2), Kellerman Group (G5) or Big Ben Group (G6). A multiple-regression analysis of coal quality versus price shows how the value of coking coal in the Japanese market appears to be related to reflectance and the free swelling index, and confirms the economic viability of the classification.British Columbia's measured reserves of coking coal contain representatives of four of these groups; Balmer Group (73%), Moura Group (/6%), Pittston Group (3.4%) and Kellerman Group (7.6%).This analysis of the quality of Western Canadian coking coal indicates that despite the need for large proportions of inertinite-rich coking coal in blends produced in the Japanese steel industry, there is nevertheless a demonstrated overabundance of Balmer Group and Moura Group coals available to the international coking coal market."

Jan 1, 1980

By M. Silver, R. H. McCorkell

The effects of covering materials on radon emanations from uranium mine mill tailings were investigated. Granular materials with air in the spaces allow radon to pass freely. Moist covers of compost or soil decrease radon emanation from tailings. Water-saturated covers were more effective, and freezing the tailings with these covers further decreased radon escape. Water itself is a poor radon barrier probably due to circulation. Plants had no effect on radon emanation through soil. Although radon diffusion through water-saturated powders appears to be very slow and inefficient, about 25% of the radon escaping from the grains in water-saturated tailings diffuse to the surface and emanate when no cover is present. The radon escaping from tailings through covers of water-saturated compost or soil is no more than could be accounted for by radon produced in the covers themselves.

Jan 1, 1987

By R. K. Singhal

"On the mining side the Canadian oil sands industry has become proficient in excavation and disposal of ore and overburden. Nearly twenty years of mining experience is now behind this industry. While local improvements to existing mining systems and practices will continue, it is believed that some further gains in productivity can be achieved by selectively introducing new ideas from other mining and non-mining industries. This type of technology transfer is vital for over-all cost-effective technology enhancement of oil sands mining operations.Discussed in this paper are the issues of mining equipment, equipment sizing, microprocessor and computer based technol¬ogy as applied to mine-wide data management, automation and remote control and a projection of likely mining systems in the year 2000!This paper reviews the ""state-of-the-art"" in selected surface mining systems and attempts to evaluate the forthcoming technology and its application."

Jan 1, 1989

By O. -J. Siljan

"Refractory materials are an integral part of aluminium production. One special feature of aluminium making is the prominent role of sodium in all parts of the production process. This presence of sodium inflicts stresses on the refractory materials through reactions and may cause severe damages to the refractory linings. The present paper address possible reactions between sodium and refractories in anode bake furnaces, electrolytic pots and casting furnaces. The discussions presented in the paper points to the importance of selecting materials with excellent alkali resistance in all parts of the aluminium making process, although alkali resistance is not the sole parameter to determine refractory life-time. ""Acid"", i.e. silica-rich alumino-silicate refractories are shown to be the best materials for aluminium electrolysis cell potlinings, whereas high- alumina refractories based on minerals like andalusite seems to be the preferred choice for anode bake furnaces as well as cast house furnaces."

Jan 1, 2004

By M. Timberlake, A. J. Jonaitis

"The DENVER Tube Press is a simple, high pressure (1500 PSI (100 bar)) filtration unit, developed for processing difficult-to-dewater materials and to produce a handleable filter cake and clear filtrate product.Lab and Pilot testwork conducted in Australia on coal fines (55-70% -35 micron (400 mesh)) have shown that total moisture contents of less than 20% are consistently achieved in the final cake products from the Tube Press.currently, these coal super fines are sent to waste due to uneconomical mechanical dewatering methods, which were only able to reduce total moisture levels in excess of 30%. Calculated, throughput rates for the 500 series Tube Press exceeded 1700 kg/hr (3750 lbs/hr). Feed solids concentration requirements are between 45 and 50% to achieve these results.INTRODUCTIONThe DENVER Tube Press is an automatic membrane high pressure filter press, which operates at hydraulic water pressures up to 1500 PSI (100 bar). The Tube Press was developed in the late 1960's by Charlestown Engineering, st. Austell, Cornwall, England, formerly a division of English China Clays, Ltd., to address more effective methods of moisture reduction of micron-size china clays. The Tube Press reduced moisture sufficiently to produce a hard surface-dry, handleable cake and clear filtrate discharge, which was recycled into the process. This development work was conducted using a 200 Series Tube Press (200 mm diameter x 2500 mm long filter surface)."

Jan 1, 1993

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton

Five years ago, VALE Base Metals (then INCO), approached Pelton's group at McMaster and described a challenging mineral separations problem. The McMaster group has a strong track record in colloids, polymers, and chemical additives for papermaking; however, they had no experience in mineral processing. They proposed employing hydrophobic nanoparticles to replace conventional low molecular weight, water-soluble flotation collectors. Over the last five years, Vale, together with the Ontario Government (OCE) have funded two graduate students at McMaster who have worked closely with flotation experts at Vale. Experiments involving both very clean model mineral suspensions at McMaster and complex ores at Vale, have shown that hydrophobic nanoparticles do indeed function as collectors. Key nanoparticle properties and mechanisms have been identified and the technology has been protected in patent applications. Efforts to commercialize the technology are on-going. We believe that this project is a good case study demonstrating the advantages of industry-university collaboration and the use of outside experts, who may come up with novel solutions to complex problems.

Jan 1, 2011

By Marcel Allard

On January 1st, 1977, SIDBEC-NORMINES INC. purchased from Quebec Cartier Mining Company various facilities located at Gagnon and Lac Jeannine together with the Fire Lake deposit. A t the same time, SIDBEC-NORMINES started its mining operations at Fire Lake, 83 km northeast of Gagnon. The paper summarizes the various adjustments which were necessary to satisfy the new production conditions, such as the physical and mechanical properties of the ore at Fire Lake, and the new crushing and loading installations at the mine, together with the transport of some 14 million tons of crude ore to the Lac Jeannine concentrator about 100km away, and finally to achieve satisfactory recovery from the FireLake ore. In addition, mention is made of the manpower organization, in which Quebec Cartier Mining Company plays an important role as manager of operations and owner of the railroad linking the mining operations to the pelletizing operations at Port-Cartier.

Jan 1, 1979

By J. M. Harrison

"The Nor-Acme gold mine is near the shore of Snow lake, northern Manitoba, about 75 miles east of Flin Flon. The claims that form the nucleus of the present property were staked in 1927 by C. R. Parres, but it was not until 1941 that diamond drilling disclosed the potentialities of the deposit. In that year a large-scale drilling programme was begun under the direction of F. Ebbutt, of the Howe Sound Exploration and Development Company. Two orebodies were outlined containing about 5,000,000 tons of ore assaying $5.25 in gold per ton. In August, 1945, construction of the mining plant was begun.All information and interpretations contained in the following brief description of the deposit were obtained from surface mapping.GEOLOGYThe ore lies at the contact between a coarse, basic, pyroclastic rock, which is the hanging-wall, and grey, acidic lavas and sediments, which form the footwall. These rocks are cut by irregular basic intrusions that vary in composition from diorite to hornblendite, and by small acidic dykes . Tourmaline is locally common in the hanging-wall rock near the ore.The ore occurs in brecciated, silicified, and ·slightly carbonatized rock. Arsenopyrite is the main sulphide and the gold is associated with it. Pyrrhotite is locally abundant and minor pyrite, chalcopyrite, sphalerite, galena, and cubanite have been noted. Two orebodies are known, the Dick and the Toots. The Toots, which is much the smaller of the two, is about 1,000 feet west of the Dick."

Jan 1, 1954

The Bluebell mine of The Consolidated Mining and Smelting Company of Canada Limited extends under Kootenay lake, in southern British Columbia, and water control underground has always been a major problem. This paper gives a brief history of the operation, and then de-scribes the methods used by Cominco to keep the combination of lake seepage, ground water and thermal spring water under control. The pumping arrangements are de-scribed in considerable detail, with illustrations to show the various stages of development, and the power supply sys-tem is outlined.

Jan 1, 1966

By G. M. Brownell

A DEPOSIT of hematite occurs on Black island, lake Winnipeg, at a point known locally as Red Rock, on the south shore of the island directly across from Clements point. The mail boat from the Canadian Pacific Railway terminus at Riverton, crossing the lake to Manigotogan twice weekly, passes near Red Rock and provides a convenient means of transportation to this part of Black island (Figure 1). HISTORICAL The occurrence of hematite on Black island has been known for a long time. Dowling's report of 1898 states(1): "An iron-ore deposit on the south side has been known' for many years, and on Jeffrey's map of 1762, showing Canada and northern part of Louisiana, Iron island is shown a short distance south of the narrows, evidently the same as the Black island of today".

Jan 1, 1945

By Yuki Tsunazawa, Shuji Owada, Sho Fukui, Chiharu Tokoro

"Since the amount of e-waste has been rapidly increasing all over the world, there is a desire to develop the effective recycling process. E-waste has various kinds of electronic components with valuable and/or hazardous materials. Recycling of them is an important subject from the viewpoint of both the recovery of valuable materials and waste treatment. In common with all mineral processing, the comminution of e-waste is a key process because the liberation states after comminution determine the overall efficiency of metal recovery. Since some of useful critical metals are concentrated in a specific component, a special and selective grinding is expected to be effective. However, the knowledge about the mechanism and the effectiveness of the selective grinding is still limited and unclear.To better comprehend the mechanism, in this study, the investigation of comminution process using the particle-based simulation was conducted. Especially, this study focused on the comminution performance of printed circuit boards (PCBs), which are major components of e-waste. The behavior of PCBs and airflow in a drum typed agitation mill having flexible chains was simulated by the discrete element method (DEM) coupled with computational fluid dynamics (CFD). To model the shape of PCBs, the particle based rigid body model was introduced into the DEM. Since this model could not directly simulate the breakage phenomena, collision energy was calculated to qualitatively evaluate the comminution performance. In addition, the simulation results were compared with the experimental comminution tests using simulant PCBs where some capacitors were solder-mounted. These results indicated that comminution performance was affected by the rotation speed of the agitator. It was also demonstrated that the comminution performance was qualitatively evaluated using the particle-based simulation and this particle-based simulation made it possible to investigate the mechanism of e-waste comminution."

Jan 1, 2016

By Dale Verran, Jared Orynik, Chad Sorba, David Bronkhorst

Denison Mines Corp. (“Denison”) has a 90% interest in the Wheeler River Uranium Project (“Wheeler River”) located along the eastern edge of the Athabasca Basin in northern Saskatchewan between the Key Lake mill and the McArthur River uranium mine. The project is host to the high-grade Phoenix and Gryphon uranium deposits, discovered by Denison in 2008 and 2014 respectively, which include combined Indicated Mineral Resources of 132.1 million pounds U3O8 (1,809,000 tonnes at an average grade of 3.3% U3O8). The Pre-Feasibility Study (“PFS”), completed in accordance with NI 43-101 in September 2018, is highlighted by the selection of the In-Situ Recovery (“ISR”) mining method for the development of the Phoenix deposit, with an estimated average operating cost of $4.33 (US$3.33) per pound U3O8. Phoenix is the highest-grade undeveloped uranium deposit known globally, including Indicated Mineral Resources of 166,000 tonnes at 19.1% U3O8 for 70.2 million pounds U3O8. The paper aims to provide a summary of Wheeler River and an overview of the proposed development of the Phoenix and Gryphon deposits according to the PFS completed for the Project. Further details regarding the PFS, including additional scientific and technical information are described in greater detail in the NI 43-101 Technical Report titled "Pre-Feasibility Study for the Wheeler River Uranium Project, Saskatchewan, Canada" dated October 30, 2018 with an effective date of September 24, 2018. A copy of this report is available on Denison's website and under its profile on SEDAR at www.sedar.com and on EDGAR at www.sec.gov/edgar.shtml.

Jan 1, 2020

By Steve T. Laflin

Since the beginning of the nuclear era, there has never been a commercial solution for the large quantities of depleted uranium hexafluoride generated from uranium enrichment. In the United States alone, there is already in excess of 1.6 billion pounds of DUF6 currently stored. INIS is constructing a commercial uranium processing and fluorine extraction facility. The INIS facility will convert depleted uranium hexafluoride and use it as feed material for the patented Fluorine Extraction Process to produce high purity fluoride gases and anhydrous hydrofluoric acid. The project will provide an environmentally friendly and commercially viable solution for DUF6 tails management.

Aug 1, 2010

By Dennis Z. F. Mraz

"Because rock salt and pot ash formations contain particles capable of elastic deformation, the material has usually been compared with various rheological models containing elastic elements. Extensive laboratory testing of salt and potash samples resulted in various theoretical conclusions based on conditions quite different from those in a deep mine. It is felt that sufficient data have now been collected from underground measurements and observations to demonstrate the inelastic behaviour of salt masses in a deep mine. The conditions in deep salt strata can be defined as near hydrostatic, because the acting pressures are very high compared to the negligible elastic limit of the salt. The pressure field and creep around the single opening is a function of its shape, size and age. The same factors, together with extraction, determine the behaviour of the mining a rea. The application of the correct analytical method in mine design can significantly improve the excavation techniques and predetermine the long-term behaviour of openings."

Jan 1, 1973

By J. G. Conaway, P. G. Killeen

"Gamma-ray spectral logging, a useful technique for uranium exploration and evaluation, has generally been underutilized by the Canadian mining industry. Provided that the technique is properly applied, it is capable of yielding reliable quantitative information regarding the distribution of uranium and other radioelements along the borehole under most conditions.In practice. there are numerous factors which potentially can degrade the quality of the log and thus any quantitative interpretation based on it. Fortunately, the appropriate choice of logging equipment and technique can avoid many such problems, and corrections can be applied to the data to compensate for most of the others."

Jan 1, 1980