Search Documents

By Bish Chanda

In the minerals business, like any other commodity-based business, management faces the daily challenge of holding down costs while the real prices of products are continually falling on an inflation-adjusted basis. Since the marketplace sets the prices, often without any premium attached for product quality, being one of the lowest-cost producers is the most viable competitive strategy. Continuous improvement is the mantra that can make the difference in terms of long-term survival of a mining company. Yet, this message has not always been followed, especially during periods of prosperity ushered by high commodity prices. More often than not, the need for improvement is only triggered by a crisis. This may be caused by events such as the onset of a severe economic recession, a prolonged oversupply situation due to an optimistic expansion of capacity during the period of prosperity, or simply falling profits alerting management to bring costs under control. At that time, there would be a need to implement a new cost-saving program, bring in a consultant to find ways to reduce costs, or re-activate an old program that had been shelved for some time.

May 1, 2003

By I. A. Cameron, F. Ham, R. Sriram

"Planned increases in electric furnace productivity and higher matte temperatures needed for the Sudbury Smelter's S02 Abatement Plan, require an improved matte tap hole. Since startup in 1978, the matte tap holes have been incrementally improved by the addition of copper cooling blocks around the refractory tap blocks. These improvements provided a tap block life of about 100 taps per campaign.In July 1993, a prototype matte taphole was installed in Number 2 Electric Furnace to develop the technology to increase tap hole service life. The design was based on a heat transfer model of the tapping process to determine candidate refractory materials and cooler arrangements. The prototype tap hole features increased copper cooling, high conductivity refractories and extensive instrumentation. Eight trial campaigns are reviewed outlining the performance of silicon carbide and graphite refractories and typical heat loads during tapping.IntroductionFalconbridge Limited operates two 36 MYA, 6 electrode submerged arc electric furnaces in Falconbridge, Ontario. The furnaces, commissioned in 1978, smelt a partially roasted nickel-copper calcine, to produce matte for converting and slag for discard. Additional details of the smelter are available in the literature(1-4).Each furnace was equipped with two matte tap holes located in the furnace end wall. Early in the campaign, matte tap holes were identified as a weak area in the furnace which could be improved. From 1981 to 1987, incremental improvements were made to the design by the addition of water cooled copper blocks. In 1993, a prototype matte tap hole was designed and installed in Number 2 electric furnace to develop the technology to increase tap hole service life. Improved service life is required to meet planned increases in electric fWl1ace productivity and the higher matte temperature needed for the smelter's S02 Abatement Plan.This paper reviews matte tap hole development since 1978; outlines the prototype matte tap hole design, refractory selection and installation; and details the performance of the prototype tap hole during the first eight campaigns."

Jan 1, 1995

By H De Beer

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Nov 1, 2011

By K. Waters, A. Navarra, T. Grammatikopoulos

Strategic decisions to develop a mineral deposit are subject to geological uncertainty, due to the sparsity of drill core samples. The selection of metallurgical equipment is especially critical, since it restricts the processing options that are available to different ore blocks, even as the nature of the deposit is still highly uncertain. Current approaches for long-term mine planning are successful at addressing geological uncertainty, but do not adequately represent alternate modes of operation for the mineral processing plant, nor do they provide sufficient guidance for developing processing options. Nonetheless, recent developments in stochastic optimization and computer data structures have resulted in a framework that can integrate operational modes into strategic mine planning algorithms. A logical next step is to incorporate geometallurgical models that relate mineralogical features to plant performance, as described in this paper.

Jan 1, 2017

By A. Fahr, T. Byczkowski, M. Genest, C. Mandache

"Layered aluminum structures assembled with rivets are often found in aircraft fuselage. These structures are exposed to various mechanical loads and a range of environmental conditions that contribute to their ""aging"". The rivet holes are the source of stress concentrations and the location of crack nucleation and growth. Detection and sizing of second and third layer cracks under fasteners represent a major challenge for non-destructive evaluation (NDE) technicians. Electromagnetic methods are currently the most feasible NDE techniques that are capable of successfully inspecting such structures. However, different probe lift-offs, due to protruding rivets and paint coatings, or interlayer separations, due to sealant or air gaps, pose difficulties in detecting and sizing cracks. In addition, the use of conventional eddy current technique is limited due to the inverse relationship between the probe spatial resolution and its field penetrability. In this paper, we present an alternative approach that overcomes the previously mentioned shortcomings by using pulsed eddy current excitation and magnetoresistive sensor pick-up. Various signal manipulations are employed for defect detection and quantification."

Jan 1, 2006

By Denni Nikols, Farrukh Z. Khan

"Highvale Mine, located at Wabamun, Alberta, produces thermal coal for TransAIta's Keephills and Sundance generating plants. Overburden stripping in the mine is conducted by draglines which normally operate on top of the overburden bench. In certain areas oj the mine, however, these overburden benches are susceptible to slope failure. In these areas, due to safety considerations, the draglines are utilized in the less productive chop-cutting mode, supplemented by mobile equipment where the bench height exceeds the dragline chop-cutting limit. This paper proposes maintaining the draglines in their normal digging mode through areas of unstable or jailed overburden, by utilizing a dragline carried toe buttress 10 ensure adequate bench stability. The data requirements and methods of slope analysis to design a toe buttress across an unstable highwall area are examined in rigorous detail. INTRODUCTIONLocationHighvale Mine is owned by TransAlta Utilities Corporation and operated under contract. It is Canada's largest coal mine with an annual coal production in excess of II million tonnes. The mine is located approximately 80 km west of Edmonton on the south shore of Wabamum Lake (Fig. I) and production is currently provided by three pits 02. 03 and 04 (Fig. 2). The entire coal production is consumed at the nearby Sundance and Keephills power generating plants.ScopeThe mining operation at Highvale Mine has had occasional slope stability failures of its high wall overburden bench. This paper examines one such failure which occurred in the summer of 1983 at Pit 03. In addition to an investigation of the failure, Terracon was asked to recommend mine operation procedures which would minimize the impact of these slide zones on dragline productivity. A method of removing the failed material by utilizing the dragline in its normal digging mode is designed. The method's advantages and disadvantages as well as the required support procedures are reviewed."

Jan 1, 1989

By Dale A. Sketchley

"Abstract - Large differences in gold content between rock fragments or small volumes of unbroken rock, commonly referred to as the nugget effect, are related to sample and subsample weights, crushing and pulverizing sizes, and density, shape and size distribution of gold grains. Gy’s sampling theory, which relates gold grain characteristics to sample weight, fragment size, and error, provides a method of estimating a sampling constant that quantifies deposit characteristics that contribute to the nugget effect.Sampling control tests provide methods for determining the sampling constant. Sampling control charts, comprising nomographs that relate sample weight, error and particle size, use the sampling constant to optimize sample weights and comminution sizes, and to minimize the variability introduced by incorrect or inadequate sampling and sub-sampling procedures. The sampling constant is useful in classifying ores into arbitrary categories according to expected sampling difficulties. Spatial variations in the sampling constant can be used to aid in defining ore types for modeling geological domains, which should have unique sampling protocols. Examples that illustrate the relationship between the sampling constant and expected sampling problems, and the spatial variation of the sampling constant, are given for various deposits. Case histories of sampling programs are presented.Quality control procedures consist of monitoring sample contamination amd accuracy and precision of analytical results. Accuracy, precision and contamination are monitored by including standards, duplicates and blanks into batches of samples being analyzed. Analytical results of standards and blanks are plotted on a batch-and-time basis with control lines at plus or minus two/three standard deviations as confidence limits of the accepted round-robin value. Examples are given that illustrate a laboratory system in statistical control and the various types of problems encountered when interpreting quality control data. These include sample transcription errors, degradation, contamination, sampling errors, detection limit problems, instrumental drift, lack of statistical control, laboratory bias, procedural problems and data tampering.Where bias is negligible, precision, as a function of concentration, can be obtained from duplicates using the Thompson-Howarth precision algorithm, which also allows calculation of the practical detection limit. Examples are given that illustrate variations in precision, with grain size, for different types of duplicates, as well as mineralogical changes and sampling errors."

Jan 1, 1998

By Evelynn Stirling

"The paper/presentation will review the evolution of diesel technology from older diesel engines (1990 vintage) through to the latest technology as a result of the ever changing emissions regulations. It will encompass the EPA Tier levels as well as the latest Euro Stage V emissions. The next step with technology will be to address the CO2 emissions, which translates to improving fuel efficiencies of the product as well as other technologies like battery electric, hybrid and fuel cells. As technology progresses it also becomes important to improve connective diagnostic systems to support maintenance practices and improve efficiencies. What will also be presented will be the key emissions changes to the different gaseous and particle mass elements as the products have transitioned from the EPA Tier 3 through to Tier 4 Final regulations. Offering a range of different technologies to the underground mining market matters as not all pieces of equipment will perform optimally due to its duty cycle and application. INTRODUCTION Rudolf Diesel built his first well-known prototype of the high-compression engine in 1897. Since that time, the diesel engine has evolved into one of the world’s most capable and reliable forms of power generation. Diesel engines can be found in a wide variety of vehicles and equipment, powering everything from agriculture and construction equipment to power generators and marine vessels. In the early days the emissions from diesels was very poor and extensive work has been accomplished over the decades to make the product more environmentally friendly. This is more important in underground mining where the space is limited and ventilation is expensive and challenging. DISCUSSION The key driver of the development of diesel technology is the legislation globally around engine emissions. The emission level requirements over the years has forced diesel engine manufacturers to build a deep technical understanding of the system and how to innovate and optimize key elements of the engine. Cummins expertise has been built over the years as the diesel engine has evolved from a relatively simple mechanical engine to an electronic system with advanced air handling, fuel system, after treatment, and controls. Cummins has also continued to expand into systems beyond diesel, including natural gas. Many new components have been added to diesel engines to reduce emissions while improving fuel efficiency and reliability and, at the same time, reduce the total cost of ownership to the customer."

Jan 1, 2019

By Frank Baczek, R. Q. Honaker, D. P. Patil, B. K. Parekh

Fine refuse slurry impoundment is a requirement for the coal industry to dispose the fines. Impoundment maintenance is an on going problem for the coal industry and its breakage creates environmental as well as financial problems. Deep Cone thickener technology which has been successfully applied in the alumina industry to dewater red mud was evaluated for fine refuse slurry. Preliminary obtained in a pilot-plant test showed that properly flocculated conventional thickener underflow slurry could be thickened to about 52.5 wt % solids and could replace belt filter press. The Deep Cone thickener was also found to dewater clean coal slurry to about 70 wt % solids. Further testing of the unit at other coal preparation plant is in progress.

Jan 1, 2004

By C. Mattich, Å. Holmström, L. Hedström

"The fluidized bed at Division Ministro Hales (DMH) division of Codelco in Calama, Chile is currently the largest operating roaster for partial roasting of arsenic rich copper concentrates. The roaster converts the Mina Ministro Hales (MMH) enargite rich (Cu3AsS4) copper concentrates into calcine with a low arsenic content that is suitable for mixing with other copper concentrates feeding a flash furnace. The plant sets a new standard for the processing of arsenic rich concentrates, both from the quality of the calcine as well as the environmental performances. The process technology and expertise are based on the solid practical experience of treating arsenic rich concentrates from both the Boliden smelter and Outotec.The partial roasting process is located next to the mine and concentrator and includes a sulphuric acid plant with auxiliary equipment. The produced calcine has an arsenic content significantly below target and the residual sulphur meets the requirement of the flash furnace. The plant operates with high efficiency cyclones resulting in a low amount of calcine passing to the hot electrostatic precipitator (HESP). The small flow of HESP calcine dust can be combined with the low arsenic calcine and still meet the flash furnace feed arsenic requirements.SO2 formed during roasting is converted into sulphuric acid, while volatized arsenic is recovered in the wet gas cleaning section of the acid plant along with a large proportion of antimony present in the MMH concentrate. Arsenic is stabilized as calcium arsenate and sent to disposal at a specially prepared site.The present production rate (September/October 2015) is close to or higher than the original maximum design capacity of the plant.INTRODUCTIONMineralogyThe mineralogy of an ore and concentrate is important, since there is a direct link between roasting performance and concentrate mineralogy. The MMH concentrate has a good combination of minerals that makes the roasting process efficient and flexible. The main minerals are pyrite, enargite and chalcocite (Figure 1). The inert content is about 15% and consists mainly of silicate and alumina based minerals. The lead content is very low and this is desirable, since the presence of even a small amount of lead will cause a substantial increase of sintering during roasting."

Jan 1, 2016

By M. E. Wilson

"The property of McWatters Gold Mines, Limited, is in the east-central part of Rouyn township and about 6 miles east-southeast of the town of Rouyn. It includes 35 claims, the group of 5, staked originally, and 30 claims acquired in later years. The Rouyn-Val d'Or road and the Noranda Senneterre branch of the Canadian National railway both pass within a few hundred feet of the mine.The group of claims in which the mine occurs was first staked in 1922, but gold was not discovered until August 1932 when a schistose zone including veins of quartz carrying considerable free gold was laid bare in a stripped area in the northeastern part of claim R.11604. Diamond drilling undertaken in 1932, and continued into 1933, shouwd that the gold extended for at least 1,000 feet along the strike. A 3-compartment shaft was sunk to 418 feet in 1933. A mill having a capacity of 50 tons a day was constructed in 1934, and enlarged to 150 tons in 1935. Production began in 1934 and continued without interruption to June 1944. Except for a few diamond drill holes, there have been no operations on the property since that time. The maximum depth of the mine workings is 1,50) feet. A total of 368,013 tons of ore having a value of $3,946,752 and an average grade of $11.04 was mined during the years of operation.GEOLOGYThe ore mined from the property occurred within the south limb of an eastward plunging syncline of volcanics and sediments cut off on the north by the Cadillac-Bouzan Lake fault. Because the rock formations within the syncline have been severed from those outside with which they were originally continuous, their correlation is based almost wholly on lithological similarity. They include an irregular middle zone of conglomerate and greywacke underlain by north and south bands of andesite agglomerate and andesite tuff, in which lenticular bands of pillowed andesite are included."

Jan 1, 1954

By R. Al-Hent, M. Aissa, J. Asfahani

"This paper presents regional radiometric gamma-ray spectrometry maps of Syria for total radioactivity (Ur) and surficial concentrations of equivalent uranium (eU). The maps were created by merging airborne and ground-based gamma-ray spectrometric survey datasets. On the regional radiometric eU map, eU anomalies are closely related to either phosphate and/or glauconite deposits. The Ur and eU maps delineate the boundaries of three phosphate deposits, close to the Palmyrides ridge, in the northern part of the Coastal Range and Syrian Desert. Scattered occurrences of uranium mineralization in other phosphate formations are attributed to secondary chemical and physical processes, rather than primary accumulation.RÉSUMÉ Cet article presente des cartes regionales radiometriques de spectrometrie gamma de la Syrie pour la radioactivite totale (Ur) et les concentrations en surface de l’equivalent en uranium (eU). Les cartes ont ete creees en combinant des ensembles de donnees, aeroportees et au sol, de releves de spectrometrie gamma. Sur la carte regionale radiometrique eU, les anomalies eU sont etroitement reliees aux gisements de phosphate et(ou) de glauconite. Les cartes Ur et eU delimitent les limites de trois gisements de phosphate, a proximite de la crete des Palmyrides, dans la partie nord de la chaine cotiere et du desert de Syrie. Des dispersions de mineralisation d’uranium dans d’autres formations de phosphate sont attribuees a des procedes chimiques et physiques secondaires, plutot qu’a une accumulation primaire."

Jan 1, 2016

By Apoorva Bajaj

Iron ore mines of Steel Authority of India Limited (SAIL) have to comply with strict chemical composition norms laid down for iron ore lumps supplied to its steel plants. This requires a careful planning of the overall ore excavation operation. In general terms, the problem can be stated as: Given the chemical composition of ore for all excavation sites, excavation capacity of each shovel, distance of each excavation site from the crushing plant and the number of dumpers available for transport of the ore, find out the percentage of ore to be excavated from each excavation site such that the production rate is maximized and the chemical composition norm is satisfied to the best possible extent. This paper presents an approach to solve this problem using Branch and Bound method. The specification for r.o.m. quality has been modified by incorporating a new parameter, ?Al2O3 / SiO2? ratio, which has a significant effect on the performance of iron blast furnace.

Oct 1, 2009

By Larson. William

What is Lunar In-Situ Resource Utilization (ISRU)? ISRU involves any hardware or operation that harnesses and utilizes ?in-situ? resources to create products and services for robotic and human exploration In-Situ Lunar Resources ???Natural? Lunar Resources ??Discarded Materials Lunar ISRU Products and Services ??Excavation, Site Preparation, and Outpost Deployment/Emplacement ??Mission Consumable Production ??Outpost Growth and Self-Sufficiency Benefits of ISRU ??Increased science and exploration hardware (instead of consumables) ??Increased safety, crew exploration time, and self-sufficiency ??Technology spin-in/spin-offs help recycling on Earth & space economy

May 1, 2009

By C. J. Kerr

"A recent information sheet from the Mining Health and Safety Branch of the Ontario Ministry of Labour was sent to all Ministry inspectors and engineers. The subject title was' 'Two Brakes on a Hoist Carrying Persons"" and it quotes mining regulation 699, sub-section 206(i):No hoist shall be used for the transporting of persons unless it has a braking system consisting of at least two sets of mechanical brakes to stop and hold the drum for the shaft conveyance transporting the persons.The intent of the regulation is that each of these brakes is to be set so that, individually, they can safely stop the drum carrying persons and also hold the drum without movement with the maximum manload.This can be achieved in the following ways: Single Drum Hoist-one brake on each side of the drum, one brake on the drum, one brake on the pinion shaft, where disc brakes are used two separate disc brake assemblies on the disc. Double Drum Hoist, brakes on companion drum can serve as backup brake only pinion brake with one drum unclutched.Friction Hoist, one brake on each side of drum As new hoists can be manufactured easily with a two-brake system, attention will be focused on retrofitting pinion brakes to older hoists.A brake mounted on a pinion shaft is designed purely as an emergency brake in the event of main brake failure , controls malfunction, and power loss."

Jan 1, 1989

By Alan G. Galley

"Advances in our knowledge of the petrochemical attributes of deposit environments and of the character and extent of hydrothermal systems associated with certain deposit types has resulted in increased application of lithogeochemistry to exploration programs. Lithogeochemistry can be used to vector an exploration program toward an area of high potential through the use of a series of collapsing scales of analysis from a tectonic subprovince down to a particular stratigraphic segment. In the case of volcanogenic massive sulphide (VMS) deposits this involves the recognition ofsuitable volcanic domains, and the identification of subvolcanic intrusions and cogenetic felsic extrusive complexes. The recognition of chemical vectors within regional-scale alteration zones and associated chemical sedimentary rocks allows the geologist to identify the stratigraphic units with the most potential for hosting a base metal deposit.An integrated lithogeochemical program requires the judicious use of major, trace and rare-earth element and isotopic analysis. Standard discriminant plots may be employed to identify suitable tectonic and lithologic environments. Analysis of the chemical and mineralogical variations in broad-scale, semi-comfortable alteration zones provides a useful set of vectors to VMS mineralization. These may include contouring raw data, element ratios on XY plots, normalizing data against known rock values, or calculating mass changes in alteration zones."

Jan 1, 1995

By Manouchehr Oliazadeh

Talc is used as a gelating, diluting, antimould and softening agent in the pharmaceutical industries. This article reviews efforts made for producing pharmaceutical grade talc from a mine located in the west of Iran, called Masoud Abad. Reaching to the pharmaceutical standards, was the principal goal of the talc beneficiation. Methods such as flotation and leaching were applied to eliminate the impurities. Considering to the negligible Fe content of the ore, the major impurity was calcium carbonate and to some extent dolomite. Depressants used in froth flotation were dextrine, quebraco and sodium silicate. Variation of collectors such as oil petroleum, paraffin, stearic acid were also used. After optimization of the effective parameters, followed by two stages of flotation (rougher and cleaner) acid leaching process was also applied as a complementary step to remove the impurities. CaO impurities in the sample was 11.63% which reduced to 1.03% after two stages of flotation, and finally reached to 0.03% CaO by leaching process. This figure is more lower than the world pharmaceutical standards (i.e. <0.6 % CaO). The highest recovery was 55% at the best conditions. Other impurities (i.e.As, lead, heavy metals ,?) which were at standard levels, confirmed by the authorized health organizations.

May 1, 2001

By Piotr Malkowski

Studies on the properties of rocks heated to high temperatures are rather rare. Such research is occasionally conducted for example; in areas around nuclear power plants. The national Polish coal gasification (underground coal gasification, or UCG) project has, however, forced the analysis of the geomechanical properties of heated rocks in the vicinity of a designed geo-reactor. Ukrainian experience with UCG show that rocks up to 2 m from the burned coal seam be at a temperature > 600ºC. Such a high temperature will undoubtedly influence their physical properties. This paper presents studies on the strength and deformation properties of carboniferous rocks in the Upper Silesian region, where the UCG process is planned. Three types of rocks were tested: claystones, mudstones and sandstones. Laboratory tests of these rocks evaluated compressive strength, elastic modulus and weight loss. An evaluation of the results of the tests comparing the thermal conductivity of rocks and their specific thermal capacity was then carried out. All of the rocks studied were heated to 300, 600 and 1000ºC, and also evaluated at room temperature. This procedure shed new light upon the behavior of heated rocks in relation to their distance from the designed geo-reactor. The test results presented were developed within Research Task No. 3 ?Developing a technology of coal gasification for efficient production of fuels and electric power?, financed by The National Centre for Research and Development under strategic research and development programme ?Advanced Technologies for Energy Generation.?

Aug 1, 2013

By A. Liard, H. Sommelet, G. Sauriol

"Description des études qui ant conduit à la conception spécifique du système de drainage de la mine à ciel ouvert. Les approches différentes sont examinées ainsi que la valeur du système recommande.IntroductionLa Division Mines Gaspé de Mines Noranda Ltée exploite un gisement de cuivre par mine souterraine et mine à ciel ouvert à Murdochville, Québec. L&apos;exploitation par mine aciel ouvert a commencé en 1965 avec une operation à flanc de montagne. Elle se poursuit actuellement sous Ie niveau de la vallée dans une fosse dont Ie diamètre est de I&apos;ordre de 800 m (2,600 pi), et la profondeur de 150 m (500 pi) sou s Ie fond de la vallee. Elle doit atteindre une profondeur de 360 m (l, 180 pi) sous Ie fond de la vallee , avec des murs hauts de 360 à 490 m et des pentes moyenne de 44°. Le rythrne d&apos;extraction est actuellement de 85,000 tonnes par jour.Dans Ie cadre des etudes entreprises par les Services Techniques de la Division Mines Gaspé, la compagnie Géomines Ltée a été consultée pour étudier les conditions hydrogéologiques et hydrologiques locales et participer a la conception d&apos;un système de drainage superficiel et souterr ain. Un tel systerne de drainage visait: a éviter les importantes venues d&apos;eau qu i affectent I&apos;exploitation en periode de crue; amaintenir les pressions hydrostatiques au sein des parois de la fosse dans les limites imposees par les etudes de stabilite des pentes réalisees par la Mine.Les principales étapes de cette etude ont porté sur: la collecte et la compilation des données sur la géologie, l&apos;hydrologie et l&apos;hydrogeologie du site; . la détermination des caractéristiques hydrauliques du milieu rocheux à partir d&apos;études structurales et de test s de perméabilité;"

Jan 1, 1981

By Terry McNulty

"Previous papers (McNulty 1998 and 2004) have dealt with the causes of successful and less successful achievement of design production rate by new processing plants in the minerals industry. Examination of many case histories has allowed the construction of curves or profiles that represent projects with similar characteristics that equate to differing degrees of care exercised during the project development phase. Simplistically, decreasing care is reflected by increasing risk and a heightened likelihood of poor technical and/or financial performance.This contribution provides an update, including recent case histories, and presents a modified Series 1A curve that includes the best 23 case histories, out of a total of 81 examined, or 28%. This is done to show that some very carefully developed and executed projects can ramp-up quickly and that owners of new projects should avoid being too pessimistic in projecting early cash flow if they are certain that they have done their homework. The role of metallurgical process development in the reduction of project risk is discussed and several financial analyses are presented that express the potential monetary value of a well-designed and professionally executed metallurgical program."

Jan 1, 2014