Search Documents

By G. W. Poling

"Construction, equipping and planned operation of a new laboratory for engineering-teaching and research in coal and mineral processing is described. This facility will provide approximately 1860 m2 (20,000 ft. 2 ) of laboratory space with nearly half devoted to a new venture in coal preparation. Two high-bay, overhead crane-accessed areas will accommodate major unit operations for each of the ""coal"" and ""mineral"" laboratories. COAL PREPARATION FACILITIES:The coal facility provides three main functional areas:(1) Sample preparation (drying, blending, crushing, screening) and sink-float washability testing.(2) Unit operations U1igh-bay, serviced by crane).(3) Analytical laboratories.(l) Sample Preparation and Sink-Float TestingBreaking or comminution of coal will be accomplished using a rolls crusher, a hammer mill, a jaw crusher, or a pulverizer. Capacity to prepare coal at rates of up to approximately 4 tph will be provided by some of these units. Large diameter (~0.5m) baths of heavy organic liquids will be available for sink-float washability tests on coal samples of several kg. Particle sizes of up to 25 mm can be tested in these baths. Smaller scale washability tests on finer samples will be accelerated by centrifuges."

Jan 1, 1980

By Ken Musgrave

"What Most Effective Management Does?It must satisfy the demands, of three groups of people: owners, employees and the public.OwnersOwners want profitable operations that will pay them a return on their investment, plus operations managed for long life. Many owners are also concerned with employee's well being and their company's public image.EmployeesJob security and a good income are probably still the most important demands, however, as time goes by, employees are also demanding more involvement in safety issues, working conditions, and even how work is done.The PublicThe public requires acceptable environmental standards, as well as enjoying the prosperity supplied by a successful operation.How are Mines Managed?Most mines are managed very traditionally. The basic credo is that the managers make the decisions, and the hourly, and junior salaried employees do what they are told. Clearly this is the extreme case, epitomized by the long service shift boss who might say ""It took twenty-years to become a shift boss, and no miner is going to tell me what to do"" .There are some exceptions, two notable ones being Campbell-Chibougamau, and T.G.S. (now Kidd Creek Mines) which, in very different circumstances, decided on a more participative style.Campbell-Chibougamau, having closed down due to unprofitable operations, reopened, using a team structure with working leaders, and a system for sharing gains against cost targets with employees. Although the system has some problems, and development miners are bonused conventionally, this has been a basically successful program.Texasgulf Sulphur, a company with a history of non-union operations, and a participative management style, made a corporate decision to operate their Kidd Creek Mine in the same way. The orebody was rich enough to allow them the luxury to do this, but they have never had a strike, so perhaps they have more than saved the cost of the benefits and salaries they needed to pay. They also reward employees with a stock distribution scheme based on service and earnings."

Jan 1, 1985

By D. Mraz

"In certain instances, rocks around underground excavations behave as a plastic mass. This paper offers several solutions to predicting the mode of plastic flow around cavities and designing mining pillars where plastic conditions exist.IntroductionWhen stresses around underground cavities exceed yield limits of the host rock, the material often behaves as a plastic mass. The best example of this phenomenon is the behaviour of salt rocks in deep salt and potash deposits (more than 500 m deep).However, many other soft rocks exhibit similar properties. For example, Jeremic(1) described certain types of coal yielding plastically under high pressure. Alder suggested that granulated rock behaves plastically.The object of this paper is to propose a de sign procedure for mining pillars exhibiting plastic flow due to the combination of rock properties and in-situ stresses.Prandtl(3) mathematically defined a concept of a generalized, perfectly plastic substance, not possessing the property of strain hardening (Fig. I). He had in mind, a solid with a quasi quasi-isotropic , polycrystalline structure having a well defined yield point, and he postulated that its material elements start and continue to deform plastically when the maximum shearing stress ""'MAX"" reaches a sharp limit, dependent on the mean value of the sum of the major and minor principal stresses:"

Jan 1, 1984

By J. George Gregr

"This paper gives a brief review of grinding mills installation procedures with special emphasis on future maintenance. The importance of cooperation between the customer, construction contractor and manufacturer's representative is discussed, as well as the imparlance of complying with standards, specifications and the keeping comprehensive installation records.Fundamentals of mill maintenance are explained with the aim being to maximize the equipment availability and to minimize unscheduled downtime. The paper also includes development of wear items design, based on operating conditions, drive components and bearings, and how to keep large gears healthy thus eliminating surprise failures.Experience with installation of a large gear on a 34-foot diameter mill in Lornex and successful application of a computer program for the gear alignment on the mill are given.IntroductionSuccessful operation of a concentrator begins with the engineering of the project and continues through selecting the right equipment, its installation , start-up period, and ends with final tuning of the process. machinery and the human factor into an efficient and viable industrial complex.The following is a brief review of grinding mill installation procedures with special emphasis on future maintenance. Fundamentals of mill maintenance are discussed with the aim being to maximize the equipment availability and to minimize unscheduled downtime, with some specific points on key grinding mill components such as bearings and drives.Finally, the experience is recounted with the installation of a large ring gear on a 34-foot diameter mill at Lornex, and the successful application of a computer program for the gear alignment on the mill."

Jan 1, 1985

By Douglas G. Jay

"Transfer points on belt conveyors have long been a source of problems for both designers and users. Conveyors are generally given a low priority in new equipment layout, thus designers are often forced to compromise due to space limitations. Consequently, for this reason as well as for reasons of initial economics, many conveyors are supplied with less than adequate transfer points.Although not intended as a cure-all, a number of existing installations have been modified with the result that spillage has been reduced to a minimum and belt life has been extended. The most striking modification consisted of replacing conventional rigid frame idlers with five-roll catenary idlers.Although catenary idlers can be traced back to the early 1900s in North America, with a patent having been issued in Washington, D.C. as early as May 29, 1907, the practical application of this concept has only recently reached North America. Major installations include applications at St. Lawrence Cement in Oakville and Iron Ore Company of Canada in Sept-Iles, as well as belt conveyors at Stelco's Nanticoke plant and yard conveyors at Syncrude in Alberta. These installations were part of major capital expenditures for new facilities and included complete conveyor systems.However, this article will discuss the use of catenary idlers on existing rigid frame conveyors for the purpose of absorbing the energy of falling lumps, protecting conveyor belts and reducing spillage. We will deal specifically with an installation at Inco Metals Company in Sudbury, Ontario, where approximately 40 five-roll catenary idlers were installed on a 42-in.-wide belt conveyor handling ore located under the railroad car dumper at the Clarabelle Mill. Before-and-after photographs clearly show the tremendous improvement in the cleanliness of the location, and the savings in maintenance costs and extended belt life have prompted Inco to consider modifying other conveyors."

Jan 1, 1982

By P. Lausch, Z. X. He, J. F. Archibald

"Documented underground fill failures have resulted because of the lack of adequate knowledge concerning fill strength and other physical parameters, as well as to a lack of consistent quality of fill materials being used by operators. On the basis of literature review and correspondence with backfill operators at 18 mines throughout the province of Ontario, non-systematic quality control procedures have been shown to exist, both within different levels of single operations and between separate mining operations, which act to provide inferior engineered fill materials and erratic application response in situ.Assessment of existing procedures set by mine operators for determining backfill physical parameters, and recommendation of optimum fill material testing and manufacturing guidelines are presented in this paper.A series of standard fill characterization test procedures are recommended to provide substantial, though not comprehensive, fill behaviour review. The purpose of these recommendations is to propose industry standards for backfill quality review. Data acquired could be utilized for fill design functions and as a means of comparing fill quality parameters between sites in a regular and more systematic fashion than is presently done."

Jan 1, 1993

The theory and practice of sampling of particulate material have been the focus of a continued attention on the part of the mining industry worldwide for almost a century now, because of its critical importance at all phases of a mining project, from exploration (bulk sampling, assaying) to production (grade control) and marketing (quality control). A powerful, complete theory was put together by P. Oy (1968 to i982), but its applications to gold ores have met with limited success to date, due to the inadequacy of its sampling variance and minimum sample mass determination formulae to the challenging case of gold ores. This paper presents a research project completed at Inco Exploration and Technical Services Inc., using a geostatistical approach, to shed light on the results of P.Gy's theory, and adapt them to the case of particulate gold ores. After a reminder of Gy's formulae and a simplified demonstration of the generic form of Gy's and more traditional formulae, an empirical approach, based on sampling experiments from four gold deposits, shows how Gy's formulae must be corrected to adjust to the case of gold ores. The generality of the results formula is then substantiated with a geostatistical analysis of the problem. A parameterized formula results, and indications are given on how to fit its parameters to experimental data. Application guidelines and charts to fit any case and budget are presented, along with a detailed practical example.

Jan 1, 1991

By W. D. Robbson

DR. G. W. RAMSEY (l): A study of our non-treatment silicosis autopsy material for the years 1940-43 inclusive, in addition to the common findings of fibrosis, nodules, and emphysema, shows marked thickening of the alveolar walls. This change is due to one or more of the following factors: congestion, edema, accumulation of both small and large monocuclear cells within the interstitial tissues and large monocuclear cells attached to the lining membrane of the alveolar sacs. This alteration in the alveolar walls, we believe, is one of the most important factors in producing impaired pulmonary function. Comparison of our first autopsy material of a case receiving twenty aluminium treatments beginning June, 1943, shows a striking change in the alveolar walls. In all areas free of silocotic nodules and fibrous tissue, the alveolar walls approach normal thickness and are free of cellular deposits. No change was noted in the old processes and none was expected. We believe that these changes in the alveolar walls were brought about by the aluminium therapy and that they constitute a major factor in the improved pulmonary ventilation noted in treatment cases.

Jan 1, 1945

By Megan Becker, Aubrey Mainza, Indigo Research Laboratories, Jenny Wiese, Gaynor Yorath, Lucy Little

Particle shape characterisation has an important role to play in mineral processing, to clarify effects of shape on rheology, equipment wear rates, comminution, classification, sizing and flotation. However in industry, shape characterisation is not routine, and the most commonly used shape descriptor in the field (circularity/ angularity/ sphericity) is not invariant. This study aims to investigate shape measurements for a fine particulate ore sample measured with different analytical devices. Two Automated Scanning Electron Microscopy devices with Energy Dispersive X-ray Spectrometry (FEI QEMSCAN® and Zeiss Mineralogic®), and a camera based image-sizer using dynamic image analysis (Retsch CAMSIZER® XT) were compared. Each device was used to analyse the shape characteristics of specific particles in both a coarse sample (–212/+150 µm) and a fine sample (-53 µm) of UG2 platinum ore. Circularity and Roundness frequency distributions obtained from the three devices were then compared. For selected individual particles, circularity showed higher variability than roundness, and the sample circularity distributions obtained by the three devices were completely different. It is clear that circularity data from different studies relying on different devices should not be compared on an absolute scale. The shape parameter roundness was found to be a more robust descriptor than circularity, and it can give a stronger indication of a particulate sample’s shape characteristics on an absolute scale. However, there were still significant differences in the roundness measurements obtained by the CAMSIZER XT and the two Auto-SEM devices, which was attributed to the dissimilar mechanisms of image capture.

Jan 1, 2016

By R. M. Oliver

THE Falconbridge property is almost completely covered with over-burden to a depth varying from 60 to over 200 feet. This overburden consists of grave], sand, and boulder, with bands of very fine silt, and there is usually a layer of water-bearing quicksand adjoining the r:ock surface. In previous shafts sunk at Falconbridge, this water-bearing quicksand had given considerable trouble, and further difficulties were expected in sinking No. 5 shaft, due to its greater size. The method described in this paper is the one adopted in sinking this shaft, after the matter had been carefully considered. No. 5 shaft is located 2,400 feet east of the old main No. l shaft, and is sunk in norite in the hanging-wall of the ore-body, which is, however, ? practically vertical to the deepest known intersection. The greatest depths of overburden prevail on the south side, or footwall, of the ore-body, and this, together.. with the fact that the footwall is wet and more badly fractured, swayed the final decision to sink in the hanging-wall. After the shaft site had been chosen and cleared, a diamond drill was set up a few feet away and a hole bored to a depth of 405 feet to test the over-burden and character of the norite bedrock. The depth of overbudren indicated by the hole was Ill feet, with the last 10 feet water-bearing. The norite was rusted and broken up for only a few feet below bedrock. A steel sinking shield (Figure l) was assembled at the shaft location, and consisted of 5/8-inch plate, 5 feet deep, built around a frame of 6 inch by 6 inch angle-iron, and braced at the corners with the same material. Twelve-inch I-beams held the shield as rigid as possible. In order to reduce binding against pebbles to a minimum, the shield was constructed with a 1-inch batter on all sides.

Jan 1, 1938

By D. G. Osborne

"The paper describes current 'tools' available to the coal preparation engineer for carrying out the evaluation of data, process design, selection of equipment and layout and design of coal preparation plants.Laboratory and pilot-scale equipment is widely available and test data can be used to provide valuable design information regarding capacities and sizing for specific applications. Pilot plants, unless they fit closely to the basic design envisaged for the eventual commercial plant, C(In often provide only limited useful information.Computing aids such as equipment simulation, plant modelling, etc. are becoming widely applied for establishing design criteria and investigating flowsheet options . Other computer tools such as computer-aided design systems are taking over some of the time-consuming tasks of detailed layout and design and estimation of quantities, etc. and providing the means for detailed examination of more than a single option.Besides computer modelling there is also physical modelling of plant buildings, plant sites and entire proposed mining areas; the former can be especially useful in finalizing design and threading' pipework and electrical reticulation systems through the plant without the resultant risk of impairment of flow, obstruction or wastefulness. Not the least of the benefits of plant models is the assistance provided for training new operating and maintenance staff."

Jan 1, 1985

By Tom Shumka

All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it is every six months or every three years. The inspection frequency depends upon gear tooth condition, and the objective is to ensure operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection, or dye penetrant examinations rely heavily on interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combined Eddy Current Array (ECA) and Alternating Current Field Measurement (ACFM) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.

Jan 1, 2012

By Barry W. Schmitke, J. M. Marino

"Cigar Lake Mining Corporation is presently operating an underground test mine in northern Saskatchewan, with a view to developing a high grade uranium deposit. The mining test is intended to demonstrate that the innovative mining methods designed are safe and economical. Two vertical mining methods are considered for the test:• box hole boring from the lower level;• blind boring from the upper level.In both cases, it is anticipated to freeze the ground before excavation to ensure hole stability and limit the inflow of water. Special care will be taken to minimize radiation exposure of personnel.Remote controlled equipment will be used where applicable.The access to the orebody was an important component of the test. After shaft sinking to a depth of 500 m, development work commenced at the 420 level in fractured sandstone which was grouted to restrict the inflow of formation water. The drifting continued in a section of poorly consolidated sand, clay and sandstone; this area was frozen to allow stabilization prior to excavation. At the 480 level relatively little water was encountered in the altered basement gneiss and grouting was not necessary; however, extensive ground support was required in the soft ground areas."

Jan 1, 1992

By D. Royston

In SAG mills fed with a variety of ore types, hard packing between the shell lifters can come and go depending on rock type and rock size distribution and the presence of a binder. Packing can appear in all sizes of SAG mills, and can be tenacious. High ball impact forces (depending on ball size) in larger mills may compact and encourage packing. Packing can have a negative impact on milling performance and a change in shell liner design may be required to remove it. However shell liner design changes need to be managed with care to ensure liner reliability. In smaller mills control of packing can extend shell plate wear-life and may help to maintain milling performance in fixed-speed mills through the liner wear-cycle.

Jan 1, 2012

By R. Argane

In this work we assessed the geochemical behavior of concentrator tailings deposited at the abandoned mines of Zeida and Mibladen (Upper Moulouya, Morocco), using physico-chemical analyses, mineralogical characterization, acid base accounting and weathering cell tests. The aim of the study was to evaluate mine drainage quality and to assess metal mobility from these concentrator tailings. Chemical analyses show that the Upper-Moulouya abandoned tailings contain relatively high quantities of lead (0.261 to 0.594 % wt). Mineralogical analyses reveal the abundance of neutralizing minerals (calcite, dolomite, ankerite, and aluminosilicates) which influence mine drainage and metal mobility in mine tailings. Leachate analyses from weathering cell tests show alkaline conditions, small conductivity values, and low solubility of Pb-mineral phases. According to these results, abandoned mine tailings in the Upper-Moulouya district have very low potential for generation of contaminated mine drainage and for leaching of heavy metals. However, the inhalation of tailings exposed to winds generate dust problem facing the local population and may cause health consequences.

Aug 1, 2013

By B. Kruger

The Dundee Precious Metals Tsumeb Smelter has evolved over the last decade to meet the challenges and opportunities brought about by a changing copper concentrate market, technological advances, environmental legislation as well as social and political changes. The paper discusses some of the challenges, successes and lessons learnt through the expansion and modernization of its smelter complex. It considers the details and impact of the transition from slag granulation to that of slag slow cooling as well as the improvement program that was implemented to more than double the refractory campaign life of the Ausmelt furnace from around 6–9 months to 15–18 months. In addition, given the evolving world we live in, it considers the challenges that the smelter faces today, not the least of it being how to remain relevant in an age of digital and other 4th Industrial Revolution disruptions. INTRODUCTION Dundee Precious Metals Tsumeb (DPMT) Smelter is located just outside the town of Tsumeb, in the Oshikoto region of Namibia. It is the largest town in the region with a population of approximately 45,000. The smelter was built in the early 1960s to treat concentrate from the nearby Tsumeb copper mines. Construction of the site was completed in 1962 and the smelter was officially commissioned in 1963 by Tsumeb Corporation Limited (TCL). At the time the smelter consisted of a lead section (including a refinery), a copper section and plants that produced cadmium, sodium antimonite and arsenic trioxide. Production commenced in early 1964, with 3,500 tonnes of copper and 6,000 tonnes of lead being produced per month. TCL was acquired by Gold Fields South Africa in 1988, and a few years later the lead section was shut down due to reduced lead content of the mined ore. In mid-1996, all mining and smelting operations were halted due to labour strikes. Ongopolo Mining and Processing Limited (OMPL) re-opened the mines and the smelter in 2000, only operating the copper section of the smelter. At the end of 2008, all mining operations were halted by the new owner of OMPL, Weatherly Mining International, while the smelter continued to operate. The closure of the Weatherly owned mines in Namibia, the primary feed source to the Tsumeb Smelter, meant that the smelter had to transition its business model from operating as a ‘captive smelter’ to that of a ‘toll smelter’. Its Ausmelt Top Submerged Lance (TSL) smelting technology and various ancillary plants made it especially suitable for accepting and treating complex concentrates that were available on the global market.

Jan 1, 2019

By Tim Grain Joseph

This paper considers the duty cycle of an electric cable shovel and correlations with measured passive seismic responses of the underfoot oil sand material in-pit. It has been observed that the cyclic activity during operation of any shovel in the oil sands environment causes the material to deteriorate and provide a less than ideal footing for this large item of equipment, whose dead weight approaches 1500 tons with a footprint of merely 75 square yards. Consequences are manifest in the form of carbody and side frame cracks, and associated downtime, maintenance activity, cost, and subsequent loss of availability. The objective of these considerations, as part of the Oil sands Equipment Interaction Program (OsEIP); currently a joint venture between Syncrude Canada Ltd., JPi Ltd., Caterpillar Inc., P&H MinePro and the University of Alberta; is to identify and provide feedback to the manufacturer and end user adverse shovel - ground conditions. This would enable the manufacturer to incorporate greater knowledge into the design process and the end user to direct operations in an enhanced proactive maintenance stance.

May 1, 2002

By R. Heikkilä

A large research and development program called RYM PRE (Process Re-Engineering) has been active in Finland since 2010. As a part of the program, a work packet Infra FINBIM is focused on the development of new national process model, specifications and requirements for the whole Finnish Infra Industry. In the Infra FINBIM, total 15 companies and main owners and 3 research organisations are included. The work is further continuing. The main achieved results up today have been the first specifications and requirements of the BIM based total process for infra sector, about 30 different pilot projects for testing of the new design and construction process models producing a lot of results and observations, a new open information transfer format Inframodel3 based on LandXML standard, the achieved acceptance of the Building SMART organization for support of international development, utilization and extension of the format within the whole infra industry, processes, software and other technical equipment. An evaluation of the results and this work will be drawn.

Aug 1, 2013

By M. D. Vance, G. R. Corbett, S. D. Butt

Surface wave imaging is a relatively new seismic technique that generates subsurface depth images without having to drill boreholes into the ground, and is rapidly becoming a standard tool in non-destructive geotechnical characterization. This paper presents a case study of the application of these surface wave techniques to image shallow abandoned mine workings at the Montague Gold Mines district near Dartmouth, Nova Scotia. This district has numerous steeply dipping narrow vein workings from historical mining activity, and has actively subsiding and collapsing crown pillars. Due to the rugged conditions at the site and the relative narrowness of the openings (often less than 1 m), a surface seismic system was developed that had improved portability and lateral resolution over other available seismic imaging systems. Seismic surveys were conducted over two sites where independent evidence indicated the presence of shallow mine workings. At one site, a comparative gravity survey was also conducted. The seismic data was processed to generate velocity vs depth images. Overall, the velocity images show vertical zones of zero velocity in the same lateral positions where historical mapping, current subsidence and gravity surveys indicate the presence of steeply dipping workings. Further, the velocity sections are consistent with the thickness of the till cover at each site and the possible weakening of crown pillars at one of the sites.

Jan 1, 2005

By A. F. Abd El-Rehim

The behavior of both transient and steady state creep of Al-4.5 wt% Cu and Al-4.5 wt% Cu-0.1 wt% In alloys was investigated using a constant stress where torsional oscillations of different frequencies and shear strain amplitudes were operated at various working temperatures. An augment in both transient and steady state creep rates was observed by increasing both frequency and shear strain amplitude of the applied oscillations. The mean values of the activation energy of both alloys for both creep stages were found to be equal to that quoted for dislocation intersection mechanism.

Jan 1, 2006