Search Documents

By Narasimha Mangadoddy, Teja Reddy Vakamalla

"Vertical hydrocyclones are very common in most of the comminution circuits. Inclined cyclones are also found for specific mineral processing applications. In this work, Computational Fluid Dynamics (CFD) technique and experiments are used to find the reasons behind the inclinations effect on hydrocyclone performance characteristics. The water and silica slurry experiments are conducted with 75 mm hydrocyclone at different inclined positions (0-600) to the vertical plane. Corresponding two-phase numerical simulations are performed with Volume of Fluid (VOF) model coupled with Large Eddy Simulation (LES) turbulence model. Multiphase simulations are carried out with Algebraic Slip Mixture model modified with lift, drag forces and Newtonian rheology model corrected with fines for various feed solids concentration. A raise in the under flow solids percentage, cut diameter and a reduction in the water split is observed with the inclination. Electrical Resistance Tomography (ERT) and High Speed Video (HSV) data is used to cross validate the inclined cyclone’s CFD air-core and solids concentration data. Predicted efficiency curves are found in a close agreement with experiments for all the inclinations. Comparison of experimental and predicted flow data clearly follows trend with the literature. Key words: Hydrocyclone, CFD, ERT, inclination, water splitINTRODUCTIONHydrocyclones are devices used to separate or classify particles based on particle size difference in the water medium. Their usage is very wide in chemical, petroleum, mineral and bio industries due to its structural simplicity, high throughput, small volume, low cost and maintenance. Cyclone mainly consists of a cylindrical section followed by a conical section attached to a single feed inlet and two product outlets named vortex finder and spigot. It works on the principle of centrifugal sedimentation. The slurry is fed tangentially to the hydrocyclone, in which larger particles are moved towards the wall and separated by centrifugal forces to the underflow. Smaller size particles follow liquid due to drag forces to the overflow. With its simple structure, the flow behavior inside the hydrocyclone is quite complex. Vertical cyclones are common in practice in most of the comminution circuits. Horizontal cyclones can be found in extreme cases which are for installation convenience rather than for process reasons. Inclined cyclones are also present for specific mineral processing applications. In coal preparation plants, dense medium cyclones are operated near to horizontal inclination of 20 degrees to allow large spigot sizes for sinks removal, self-drain of contents during shutdown. In the phosphate removal, dense medium cyclones are inclined with an angle between 0-90 degrees for better separation of ore and tailings (Liu Feng et al., 2006). Even in the clusters, hydrocyclones are mounted with an inclination around the feed distributor for uniform distribution of slurry and under flow collection. It is believed in mineral processing industry that inclined cyclones would fetch the benefit in number of ways while classifying the material by size. Gravity influences the cyclone performance through the air core size and position variations in large cyclones. It also favours the cyclone operation at coarser cut points without varying any other design and operating parameters. Minimizing fines misplacement to underflow can be achieved with inclination."

Jan 1, 2016

By R. S. Adhikari

This paper presents an innovative computer vision method for condition assessments of bridges with multiple defects in bridge elements using digital images. This work utilizes 3D model of existing bridges and overlays digital images on 3D model to simulate on-site visual inspection. The analysis of element condition index (ECI) of bridges requires information about the severity and extent of defects in elements. In general, ECI is evaluated manually during routine bridge inspection considering the severity of dominant defects. The evaluation of ECI with multiple defects needs to be addressed with consideration of dominant defect as well as the interaction among defects. However, Image-based quantification techniques largely depend on geometry of objects (i.e. shapes). Shape vectors of a given object change as they are translated, rotated, and scaled with different magnitudes. This work considers shape preserving algorithms such as, affine and projective transformation for proper image alignment. Semi-automated approach for detection and quantification of concrete distress such as cracks and spalling are considered for the defects analysis. The proposed methodology ensures the consistency in reporting ECI and eliminates the shortcoming of traditional approaches.

Aug 1, 2013

By Patrick S. Hudd

Traditionally in hard rock mining, large diameter raise boring was thought of as 3.04 metre or 3.66 metre diameter holes 300 metres deep. Mine and ventilation engineers were challenged to design systems either incorporating such holes, or slashing and modifying to suit. Now, 5.49 metre diameter holes up to 1,000 metres deep are being excavated. The ability to pilot and ream such holes not only creates new options for mine engineers in mine ventilation system design, but also creates new opportunities in mine access. By combining holes of this diameter with the ability to accurately drill long pilot holes within the diameter of the pilot hole through the entire length of the hole, borehole hoisting systems are now fully capable of being main production or service accesses for mines. This paper will review the present day capabilities of large diameter raise boring, potential applications for such excavations and some considerations for companies contemplating using large diameter raise boring in their operations

Oct 1, 2010

By V. ?. Chanturiya, I. Zh. Bunin, M. V. Ryazantseva

"Surface changes in naturally occurring metal sulfides (pyrite, arsenopyrite, sphalerite, chalcopyrite, galena, and molybdenite) due to treatments from high-power electromagnetic pulses (HPEMP) at varying times were studied using X-ray photoelectron spectroscopy. Analysis of the obtained results revealed common patterns and differences in surface transformations. The transformations were found to include two main stages. The first stage was observed at low treatment intensities (up to n ~103 pulses). At this stage, formation and accumulation in the surface layer of the nonstoichiometric sulfide phase, oxides and hydroxides, as well as elemental (polysulfide) sulfur and/or metastable sulfur species (thiosulfate, sulfite) was observed. The second stage (N = 3·103 pulses) is characterized by thermal removal of sulfur species and renewal of the mineral surface (sulfidization).It was found that the chemical changes of the sulfur on the surface layer of pyrite, arsenopyrite, chalcopyrite included accumulation/formation of S0 (Sn 2-) at the first stage of the transformation, followed by its removal. An increase in the surface concentration of elemental sulfur for pyrite and chalcopyrite was 10–12% while arsenopyrite was approximately 5%. A more complicated chemical change was observed for sphalerite and galena, that included formation/accumulation of metastable sulfur species (thiosulfate, sulfate) at the initial stage (up to 103 pulses) and during longer treatment times, the sulphur is reduced back to its initial state (sulfide or disulfide). The increased concentration of S0 sulfur, compared to the original sample, was only 3% in galena and sphalerite.The application of HPEMP treatment to improve flotation selectivity is supported by singlemineral flotation tests. Changes in flotability as a result of HPEMP treatment are principally explained by surface phase changes that resulted in higher adsorption activity."

Jan 1, 2016

By Shugang Li

Coal and coal-bed methane are valuable energy resources. If they can be extracted simultaneously and safely, the triple purposes of mine safety production, new energy resource supply and environmental protection can be fulfilled. After mining, the mining induced fissure distribution feature and methane delivery behavior in overlying strata were closely related to the relieved methane degasification. Using physical simulation and numerical simulation, it was explained that the distribution feature of mining induced fissure was the Elliptic Paraboloid Zone (EPZ) in three-dimensional space. Based on the key stratum theory, the types, parameters, characteristics and dynamic evolution behavior of the mining induced fissure EPZ were analyzed. Applying environmental fluid mechanics and the mass transfer theory, the relieved methane floating-diffusion equation of the EPZ was established, and the corresponding transport process was analyzed. Using the field practice of relieved methane degasification in Tianchi Coal Mine, it explained that the mining induced fissure EPZ was the storage and delivery area of relieved methane. The degasification effect will thus be useful if the drainage system is laid in the EPZ. Such studies can provide the theoretical basis and technical support for the safe simultaneous extraction of coal and methane.

Aug 1, 2013

By M. Bender, H. D. Goodfellow

"Belt conveyors, because of their low capital and operating costs and inherent flexibility in handling a wide variety of products, have numerous applications in the mining industry. With the increased emphasis on improving the workplace environment, dust emissions from belt conveyors at transfer and other points have become a significant problem for many applications.The paper reviews belt conveyor dust control technology and compares dust emissions from belt conveyor systems with other possible materials handling systems. Technical information on existing belt conveyor installations which have been designed to minimize or eliminate dust emissions is summarized. The important features of good design as well as the necessary input from operating and maintenance personnel are highlighted. The status of research and development work on dust control on belt conveyor systems on a world-wide basis is discussed. A proposed methodology for field measurements of emission factors from belt conveyor systems is presented. Data collected from such a test program can be used to establish a design basis for new dust-free belt conveyors.IntroductionBelt conveyors have proven themselves over the year s in the mining industry as a reliable and low-co st method of moving bulk material at high tonnage rates. Because of the above, as well as their inherent flexibility in handling a wide variety of products, belt conveyors are often called the ""workhorses"" of bulk material handling systems. For many processing plants, belt conveyors serve as the ""vital link"" in providing feed to the plant and the removal of the finished product. As would be expected, there has been considerable engineering effort in designing rugged and reliable belt conveyor systems.It is also well known that belt conveyor systems are a primary source of respirable dust emissions. The major sources are from the tail pulley where material is received and the head pulley where material is discharged, from the return idlers, due to the fine material attached to the return belt, and from the take-up pulley. It is usually considered that for dust particles less than 10 microns, these particles will remain airborne and thus can have a profound effect on the workplace environment."

Jan 1, 1982

By F. Hampshire

"IntroductionThis paper is intended to cover questions raised by operating staff at various installations and is not intended to give comprehensive coverage of power plant and power system design. The paper is concerned mainly with the electrics , although a brief section gives the reasons for selection of diesels rather than other prime movers.The material is not new but brings out points which seem to be raised regularly during the design , commissioning and operation o f a new plant. Diesels versus other Prime MoversDiesel-electric plant for the mining industry falls into two major categories -emergency power and prim e power.1) Emergency power (for use only when the regular utility supply has failed) requires reliable starting and operation and reasonable first cost. Fuel economy and maintenance are of little importance as the machine(s) generate few kilowatt hours only. The diesel's competition in this field is the gas turbine, however diesels are more widely used than gas turbines in this application.2) Prime power is a different situation as the bottom line of total cost is highly affected by fuel costs.In general , mines which are within reasonable transmission distance of an existing utility find the lowest net cost result s from hooking up to the utility. If a min e is remote from an electric utility then the possible alternatives are:a) Hydro- electric power if there is a site capable of development at reasonable cost including the cost of transmission facilities. Such sites are not common, but brief and inexpensive considerationof this possibility is warranted .b) Diesel power with consideration of different grades of fuel.c) Thermal (steam) power generation from coal or oil.d) Gas turbines.In addition to the above there is the possibility of wind power (as a supplementary source) and a number of technologies which may become feasible in the future (e.g. small nuclear plants, fuel cells). For obvious reasons, small isolated generating systems required for remote mines, tend to lean to conservative technology.Among the fossil fuel plants, the diesel enjoys advantage on over-all costs as summarized in Table 1."

Jan 1, 1986

By L. Zhu, S. Kaierle, M. Dahmen, C. Zimmermann, T. Haubold, I. Kelbassa, C. Mattern

Application of integrally bladed disks (blisks) is of increasing interest in compressors of aero engines. Blisks are preferred due to their potential for size and weight reduction, for increased performance and for reduced manufacturing costs compared to conventionally bladed disks. In case of a damage the blisk aerofoils cannot be simply replaced. If the damage is beyond acceptance or blending limits refurbishment is possible only by scrapping the whole blisk assembly, or more cost effective by the application of advanced weld repair methods. Weld repair of blisk aerofoils is challenging as it affects a critical part with specific requirements regarding its mechanical integrity, and as the accessibility is usually limited. The paper describes the ongoing development of advanced weld repair processes as part of a comprehensive repair strategy which have been developed for small-sized blisk assembly to give competitive maintenance cost.

Jan 1, 2006

By Atulya Verma, Samantha Espley, Nashel Kalaka

Numerical modelling simulations of proposed mining sequences are used to evaluate mining induced stress concentrations and their migration associated with the progress of mining. This analysis is a standard practice for most prospective mining projects at various levels of feasibility study. The studies are usually initiated at the beginning of the mining cycle, on a global scale, and are maintained and updated throughout the life of mine (LoM) to identify or address local issues and the required remedies as and when needed. Developments in numerical modeling techniques along with advancements in computing technology and data storage/management capacity have given rock engineers access to a huge volume of data that needs to be analyzed and assessed. The most common approach to numerically evaluate stress concentrations and migrations in underground mines is to select the points of interest in a given volume such as the back of an excavation or points within pillars around critical infrastructure, and plot the stresses or a derivative of stresses over time to represent life of mine concentrations and migrations of stresses. The problem with this approach is the sharp gradient of stresses close to excavation boundaries. Slight changes in the location of selected points can change the stress concentration and migration patterns substantially and all generalized statements about LoM risk can be challenged in one way or another. For global stresses, the most common current approach of data analysis is by viewing series of pictures representing stress contours. In this approach, it is easy to overlook some critical detail and/or be masked by personal preferences of contour/picture representation. To overcome the problem of representing and analyzing huge volume of stress simulation data, the authors, through their experience at different mining operations, developed a volume-based technique to reliably evaluate mining-induced stress concentrations and migrations. The volume-based approach is for risk-based assessments of adjacent regions in the rockmass, in and around planned stoping excavations. The volume of interest is the entire ore body that is planned to be mined, but it could be just a part of the ore body depending on the specific use case. The risk identifiers are the induced stresses as compared to the strength of the rockmass. Over the LoM, the risk identifiers are tracked versus the corresponding excavation ratio of the zone. This approach is very effective in identifying the stages of mining that are contributing the most to the mining induced stress risk and the results can be used for proactive planning and mitigations measures such as alternative mining sequences, or stope sizes, or extraction methods. The approach has also been very successful in application at mature mines, particularly in assessing the re-initiation of mining in zone that has been dormant for some time. The volume-based approach allows for an assessment of the current state of the rockmass and the identification of future risks when planning resumption of mining activities.

Jan 1, 2023

By Pierre Laliberté

L?utilisation de plusieurs nouvelles technologies et systèmes de contrôle visant des économies d?énergie dans une exploitation minière pourrait laisser croire qu?il suffit d?additionner les économies potentielles de chacune de ces technologies pour en évaluer l?économie totale. Une addition simpliste des pourcentages d?économie pourrait, dans certains cas, dépasser 100%, ce qui est évidemment totalement incohérent. Les LMSM-CANMET sont à réaliser une étude dont les résultats serviront à estimer l?influence de certaines technologies et systèmes de contrôle visant des économies d?énergie et à évaluer l?impact des unes sur les autres. En outre, un modèle de simulation est en cours de création afin d?évaluer les gains incrémentaux liés à l?application d?une série d?innovations dans une exploitation minière. La présentation fera le point sur l'état d'avancement du projet en plus de soumettre quelques exemples.

May 1, 2007

By B. R. Rakishev

Balanced development of mining works at all the benches of a working zone by use of the excavator-automobile complex is achieved by transition to the technology of the bench excavating with cross panels by the two-sub-bench scheme with the changing levels of the working platforms (is patented in Kazakhstan). In deep quarries realization of this technology will allow to reduce the current volumes of the stripping ore excavation by 10?15 % and more, to increase the opened reserves of minerals by 20?50 % to decrease volume of mining-capital works for construction of stripping excavations by 2?4 times and to provide efficient use of powerful excavator-automobile complexes.

Aug 1, 2013

By T. Yalcin, S. Brunet

The flocculant-assisted hydrocyclone involves the addition of a flocculant to the cyclone feed for the purpose of obtaining a clear cyclone overflow, and thereby eliminating or reducing thickener requirements in tailings disposal operations. This paper describes the testing of this concept on the iron ore tailings of Quebec Cartier Mining Company's Mount Wright Concentrator. The current practice at Mount Wright makes use of conventional hydrocyclones and thickeners for the disposal of their tailings, which are generated in a spiral gravity separation circuit. The test work was conducted primarily on their cyclone overflow product which becomes the feed to the thickeners. A detailed study was carried out to determine the sedimentation properties of these tailings in terms of their response to a variety of flocculating reagents, and to varying conditions of pH, pulp density and flocculant dosage. The tailings were then processed in a laboratory hydrocyclone with the aid of flocculants. The use of a shear resistant flocculant, in particular, was found to yield cyclone overflows with low solids contents. Based on the test results obtained, a conceptual flow sheet has been proposed for the treatment of the iron ore tailings at the Mount Wright Concentrator.

Jan 1, 2004

?It is not the strongest of the species that survives, nor the most intelligent. It is the one that is most adaptable to change.? Charles Darwin. Canada?s mining and exploration companies have evolved over the past century from essentially a pick-and-shovel industry to a high-tech industrial sector. This evolution has occurred in fits and starts, and has been driven by the shifting environment of economic, technical and social opportunities and pressures in Canada. As labour costs have gone up, and labour availability has gone down, the industry has evolved more efficient processes. As mineral prices have increased or fallen, the industry has evolved either by expanding or shrinking production, or by changing processes to adapt to the newly prevailing conditions. As stringent environmental protection legislation has been implemented, the industry has adapted accordingly, and has substantially changed its mindset to incorporate sustainability into its way of doing business. These changes have occurred over a number of decades, and have usually occurred as the industry?s reluctant response to pressures it couldn?t evade. This model mirrors the classical paradigm of natural selection where evolution is driven by pressures external to the organism (or organization) ? change occurs to the degree necessary for survival and prosperity, but generally no further. In recent years a new paradigm has started to come into play in Canadian mining and exploration. Rather than only a reactive response to the external economic, social and technical factors, groups within the mining community are becoming proactive in developing strategies for future adaptive change. Instead of each against the other, they are developing more sophisticated paradigms where they can both compete against (such as in marketing) and cooperate with (such as for tech development) their fellow organizations. Most importantly, they are seeing individual and national advantage in a collaborative Canadian approach to address the advantages of overseas competitors who often have lower labour costs, lesser environmental standards, or more accessible markets and transportation. This has translated into large-scale mining community support for the Canada Mining Innovation Council, and its programs in exploration, mining, processing, HR development, energy and environmental stewardship. This new paradigm is adaptive to the current environment but is substantially different from the older way of doing business in two major ways ? it is based on a collaborative approach to competitive advantage, and it is highly proactive rather than reactive. All the programs have their priorities determined principally by the mining and exploration companies, whose first obligation is to determine the long-term research priorities of the industry as a whole, rather than for their individual companies. Only after industry consensus on priorities does the research community become engaged in the implementation of specific projects to address those identified priorities. A goal of the program is to effectively create a virtual mining research laboratory, by engaging all the major research centres in the country. This approach is being actively adopted by much of the Canadian mining community, and argues well for the adaptability and long-term survival of mining in Canada.

Aug 1, 2013

By W. Keith Buck

This paper defines the discipline of mineral economics. By example, it describes the application of the tools of economic analysis to mineral problems - to problems in the areas of: mineral resource analysis and forecasting, mineral industry activity from exploration to distribution and marketing, mineral commodity analysis, and mineral policy analysis and policy formulation - all in a regional, national or international context.

Jan 1, 1972

By Alex McEachern

MINING LEADS WAY TO PROSPERITY THE year 1937 will stand out in the history of mining and metal products in Canada as one of which we shall always be proud. The combined contribution of these industries played a large part in leading Canada back to prosperous conditions after years of stress and strain that left their mark upon business the world over. A review of general industry shows a marked improvement over recent years. The upward trend continued un-abated most of the year and not a few of the industries had all they could do to supply the demands. A fact that should be appreciated in a year of wheat failure over an extensive area of the Prairie Provinces is the shifting of the basis of Canadian prosperity from agriculture to that of mining and the use of metals. To the great demand for minerals of all kinds, our mines have well responded and many new high levels were reached. This reflects great credit upon the men who direct the activities of the Canadian Mining Industry. Possessed by a spirit which refused to accept defeat in 1931-1932, they began to increase the efficiency of their departments, explored all channels hitherto untried, and won through to a crowning success. Who among them dreamed that their country's extremity would be their Alex. McEachern opportunity, and that through their united efforts our young nation would be enabled to hold that high position she has attained in world affairs?

Jan 1, 1938

By Yongquan Zhu, Zhengguo Zhu, Zhichun Liu, Chao Kong, Xinqiang Gao

"The aim of the study is to have a good understanding of the change in the seepage field during and after the tunnel excavation in weathering alteration rock. Field tests are used to monitor the changes of the water table and the numerical model is used to analysis the influence of the seepage filed with different operation conditions during and after the tunnel excavation. Results indicate that the depth, diameter and pumpage of precipitation well are the main factors that have a great influence on the drainage effect. Results also indicate that different operation conditions had various effects on the decrease in water yield during tunnel construction and the recovery in groundwater level after construction.INTRODUCTIONAs a potential disease during tunnel construction, Gushing water not only affected construction schedule, increased construction cost, as well as affected tunnel stability and safety during operation, but also decreased ground-water level. What’s more, the fall of water table caused by gushing water in tunnel would have influenced surrounding residents’ living water, agricultural water and ecological environment around tunnel. In recent years, enough emphasis has been paid to the influence on environment due to the construction of tunnel as a result of the reinforcement of people’s environmental protection awareness.As a result of water collection and drainage after excavation, groundwater was discharged into the tunnel, which caused a loss of water resources in the adjacent mountain mass. Furthermore, during tunnel operation, it was difficult for groundwater level to resume its original condition, which caused a bad ecological environment, because drainage system during tunnel construction destroyed its original hydrologic dynamic balance.In order to study whether decreased groundwater level resulting from tunnel construction could be restored during operation to its original condition, this paper gave a field monitoring on tunnel displacement during construction and simultaneously, generalized model of regional hydrogeology was created according to field hydrogeology to carry out a calculation of stable seepage flow and draw comparisons between recovery conditions of various water levels."

Jan 1, 2015

By L. G. Morrell

Introduction A Self-Dumping cage which combines the features of a small skip and a cage has been used in a vertical winze between the 2,000 and 2,500 levels at the Coniaurum mine for the past three years, during which time its success has been demonstrated by uninterrupted service and low maintenance charges. lt was designed by John Reddington, mine manager, and was built under his supervision in the Coniaurum mine shops. Being new in many of its operating features, a small-scale model was made and tried before the final construction was undertaken. The mechanical performance of the model suggested a few minor changes that were incorporated in the final drawings. During its three years of use, the automatic dumping device has saved the expense of deck-handling of the cars. This actually represents a gross economy of something over four times the cost of construction and installation, which totalled $1,325. The cage, empty, weighs 2,200 pounds, of which 500 pounds represents the weight of the dumping accessory and necessarily heavier construction. Besides a considerable financial saving, the time saved in unloading increases the daily hoisting capacity of the winze. In raising ore from the 2,500 level, five minutes are required for a complete trip. Allowing one minute for the alternative of decking, we believe that the automatic dumping has increased the capacity of the winze hoist nearly 20 percent.

Jan 1, 1933

By T. G. Joseph, M. Welz

ABSTRACT: Joseph (2002) introduced passive seismic monitoring to measure mining equipment performance. This paper evaluates the potential of passive seismic monitoring to correlate mining equipment operation with oil sands surface response, with a mining hauler as the seismic source. When applied to moving haulers, this action–reaction approach is complex. Vibrations from on-board equipment, such as pumps and tires, dirty the signal with noise. To facilitate any correlation, the signal must be cleaned up. Existing geophysical analytical techniques were manipulated to evaluate the noise problem and to filter sufficiently to permit an evaluation of whether a mining equipment action–ground response relationshipis in fact discernable.

Jan 1, 2011

By D. Janney

Kennecott's Utah Smelter commenced operations in June 1995 utilizing Outokumpu Flash Smelting (FSF) and Kennecott-Outokumpu Flash Converting (FCF) technology. After some initial teething and equipment problems the smelter achieved its design capacity in mid-1997 and now processes over 1.0 million tonnes of copper concentrate per year with exceptional environmental performance. The smelting furnace has operated for 11 years and the converting furnace for 5 years without major shutdowns. The first major smelter shutdown commenced in September 2006 after extensive planning. The FSF was completely re-bricked and the latest above and below bath containment systems installed. The FCF was inspected and re-bricked with some improvements made to the above bath containment system. The FCF life is now anticipated to be the same as the FSF. Numerous improvements and modifications were made to the rest of smelter facility including extensive upgrades to the dry electrostatic precipitators. Production ramp-up was smooth with the smelter now frequently operating at acid plant capacity.

Jan 1, 2007

By Arsalan Talebzadeh

Construction -Surface ?First two intake fans constructed in 2007; third fan added in 2008 to reduce resistance in the system. 450 HP fans. ?Excavation for exhaust fans started in 2008. ?In parallel with underground construction in preparation for the changeover. ?Bulkhead in place prior to completion/ commissioning of

Oct 1, 2010