Search Documents

By C. O. Stee

Introduction The property of Siscoe Gold Mines, Limited, is located on an island of three hundred and forty acres in lake Kienawisik, about fifty-two miles east of Noranda and forty-three miles south of Amos, Quebec. Lake Kienawisik is a part of the Harricanaw drainage system and is crossed by the main line of the Canadian National railway at Amos. This waterway is navigable for boats with a draught of six to eight feet. Diesel engines have been the source of power at the property since milling operations were commenced in January, 1929. The power plant as first designed and built was for a milling capacity of 100 tons. Two Polar-Atlas units, each of 200 h. p., comprised the original installation. With the growth of the 'mine, more engines were added until, at the present time, there is installed at the Siscoe what is rated the largest Diesel plant at any mining property in Canada. Definition of a Diesel 'The Diesel engine is an internal combustion engine which works with liquid fuel introduced after, and independently of, the air charge at a time when communication between the cylinder and the outside atmosphere is cut off, and which ignites the fuel by compression-beat and stored combustion-heat unassisted by heat sources outside the cylinder itself while the engine is in stable operating condition"(1).

Jan 1, 1934

By George R. Elliott

Introduction The pages that follow present a brief chronological survey of views which have been held, and of legislation enacted, for the regulation of the natural gas and oil industry in the Turner Valley field, especially as regards conservation of the natural gas. To provide a necessary background for an adequate understanding of the progress of events in western Canada, there is included also a compilation, from technical and legal authorities, of some of the more important measures which have been adopted for the regulation of the oil and gas fields of the United States, where these measures have had, or are likely to have, a bearing on the course of our domestic industry. Owing to exigencies of space, it has been possible to refer only to the most outstanding proposals and legislation, and to these in the briefest possible form. Although, so far as Canada is concerned, the data presented are restricted almost entirely to the Turner Valley field, it is the hope of the writer that the paper may prove of value for purposes of reference: for any similar gas and oil fields discovered in western Canada will certainly revive and intensify the problem of the proper steps to be taken for the conservation of the gas. Definition of 'Conservation The term conservation has been so misunderstood and misrepresented that, to many persons in Alberta, it means little more than closing-in wells. In the light of the definition of Charles E. Hughes, that 'True conservation of a raw material is its economical use', the subject of natural gas conservation is inseparably involved with the study of the function of the -gas and with the development of the principles of unit operation.

Jan 1, 1934

By G. E. Agar

This paper deals with the prediction of locked cycle flotation results from data developed from individual batch tests. A postulate is made that the distribution of material in a separation stage is determined by the chemical conditions and the flotation time and that this distribution can be characterized by split factors which are constants for a fixed set of conditions. With this premise, it is demonstrated that a steady-state balance can be calculated for a circuit. Although the necessary equations can be solved algebraically, a computer program was written that uses an iterative technique to arrive at the steady-state balance. The program is written so that a variety of circuits can readily be simulated. A number of examples are examined to demonstrate the validity of this simulation procedure. The sensitivity of the material balance to changes in the split factors was examined. Data developed from different flowsheets are presented on sulphide ores, on copper-nickel separation and on silver flotation.

Jan 1, 1978

By J. I. Mathis

"The failure that was utilized for developing this model was a double bench-scale failure, approximately 20 m in height, in the Misery pit at BHP Billiton’s EKATI mine site. The bench that failed was excavated in biotite schist. Due to previous problems with bench-scale toppling failures, this bench was excavated with a 70° inclined, 30 m deep preshear. Upon exposure, the wall was very clean with half-barrels commonly observed from the pre-shear operation.In August 2003, a bench failure of about 1000 t occurred in this pre-sheared biotite schist (Fig. 1). Upon examination it was noted that the foliation that paralleled and dipped at 70° into the face when excavated was approximately horizontal at the top of the failure (Fig. 2). While the failure mode itself appears complex, the failure was apparently driven by three factors:• a low-angle, low-frictional strength fault or discontinuity at the base of the failure area;• water either contributed meteorically from precipitation and/or from permafrost melt; and• foliation planes providing a viable toppling geometry once toe block motion began to occur.The above details are illustrated in Figure 3.After considerable thought and analysis, a model was postulated for the failure.It is thought that the entire failure had been triggered by displacement of a toe block (Fig. 4). This toe block is bounded on the back by foliation, the bottom by a low-angle, lowstrength fault, and the front by the bench face. Water pressures behind the bench face developed forces on the block as can be seen in Figure 5. These forces were sufficient to induce block motion. As can be seen in the relative shear strength diagram in Figure 6, only a small amount of water is necessary in the face to initiate block displacement. Note that in this figure, a simplistic piezometric pressure distribution was assumed."

Jan 1, 2004

By A. P. Sasmito

It is well known that underground miners are exposed to one of the most dangerous working environments on earth. As mine delve deeper, the geological factor, mine position and climate condition as well as heat generation from mining machine give rise to the mine operating temperature. This, in turn, has an adverse effect on the environment and thus leads to higher operating costs. Careful estimation and design of air flow rate, spray system, cooling load and additional ventilation auxiliary equipment are of importance to ensure safety, comfort and productivity whilst maintaining low operating cost. A computational fluid dynamics simulation approach is employed to examine underground mine ventilation in a 36 m cul-de-sac of tunnel of coal mine. The model predictions in the turbulent range were validated by comparison with published data. Different turbulence models were tested to select one that yields adequate accuracy and is computationally efficient. Effects of the following parameters are evaluated: tunnel geometry, air flow rate and inlet air temperature. The objective of the simulation is to arrive at an optimal strategy for ventilation and thermal comfort at low cost.

Aug 1, 2013

By R. England

"This paper describes the objectives and design parameters for the operation of a computerized In-The-Hole (I. T.H.) Drill. The principal objective is to add computer control to an Inco 00-60 I. T.H. (CMS-CD-90) drill in order to drill holes with greater accuracy. The computer provides control of the angle of the hole by maintaining the orientation of the drill head, and optimizes the straightness of the hole by maintaining a constant force on the drill bit.The second objective is to provide the greatest degree of operational automation, so the objective outlined above can be accomplished with a minimum of operator intervention.In order to provide full operational automation it was necessary to also provide the capability for the computer to add and remove drill rods. To accomplish this, a rod-handling mechanism consisting of a rod storage rack and rod manipulator arms was used.IntroductionMining machinery that lacks automatic control has been found to show a high degree of variation in work output and performance quality when operated by different personnel. Differences in operator attitude, judgment, and skill are reflected directly by production statistics. The addition of automated control has the potential for considerable improvement in machine life and performance. Even with a more acceptable mine environment and much safer conditions than ever before, situations still exist where it is preferable to remove personnel for reasons of safety as well as productivity. Typical advantages of such situations are automated skip loading and hoisting, and the use of remote control load-haul-dump units exposed to open stopes.Other cases arise where heavy work is required under conditions where lighting is poor, floors are slippery, noise levels are high and dust and oil mist exist in the atmosphere. I.T.H. drilling is carried out under such conditions and is one operation where automation can easily be justified."

Jan 1, 1987

By F. R. Archibald

A STATEMENT on this subject by A. D. Turnbull, presented and discussed at the Annual Business Conference of the Metallurgy Division, C.I.M., held in Ottawa on April 22nd 1957, led to creation of a committee "too see if the Metallurgy Division of the C.I.M. can improve this situation". Without discounting the general problems of education and short-ages in other fields, the committee is primarily concerned with deficiencies related to metallurgy. The committee members are: F. R. Archibald, Chairman, A. D. Turnbull, L. E. Djingheuzian, J. U. Mac-Ewan, and L. M. Pidgeon. Following exchange of views among the committee members a general attitude of approach was established and a background of reference material assembled. It is the purpose of this review to acquaint those interested with the reference material, to offer an appraisal of the situation, and to suggest a programme for action by the Metallurgy Division of the C.I.M. Before proceeding with the ?presentation it is fitting to point out that, notwithstanding some rather important developments in public concern for educational matters, as well as changes in the level of activity in the metallurgical industry, the statement (April 1957) by Mr. Turnbull still stands as a sound article of reference.

Jan 1, 1958

By Gerald Blackmore

"This paper suggests that with the settlement of long-term contracts of fifteen years' duration, with prospects of extension, the coal mining industry has, for the first time, a complete commercial justification for large-scale planning.The labour costs of coal production over past years are analyzed and, with the acceptance of the premise that the basic shift rates are certain to rise in the years to come, the paper suggests that forward planning should provide &r capital investment to make a traditionally labour-dense industry into a capital-dense industry.Automated methods of manpower deployment and timekeeping and the monitoring of all equipment back to a central control point are discussed as ail-important means of obtaining maximum utilization of high-cost capital investment.Principles of payment of the work-force, and the utilization of equipment 24 hours a day, seven days a week and the maximum number of days a year, are dealt with as means of achieving maximum capital utilization. Some of the new technical underground and coal preparation problems which will undoubtedly result from the concentration of workings and maximum machine utilization are discussed, and the author makes suggestions as to how these might be solved.In short, the author predicts that if the coal mining industry is prepared to recognize the problems and invest in modern equipment backed by highly trained staff. then the outcome will justify the high capital investment involved. He stresses the importance of human communications in achieving this end."

Jan 1, 1970

By A. Desbiens, R. del Villar

"This two-part paper summarizes the design and implementation of a distributed PIbased control strategy installed at the B grinding circuit, at the Kidd Creek Division of Falconbridge Ltd. Part I details the design of the control strategy using a grinding circuit dynamic simulator (DYNAFRAG). The first step consisted of sampling campaigns and data processing to calibrate DYNAFRAG. Then, several control alternatives were designed and tested with the simulator. The main feature of these strategies is their ability to regulate or keep within an upper and lower limit five output variables (circulating load, rod mill density, cyclone feed and overflow densities and pump box level) with only three manipulated variables (rod mill water, pump box water and rod mill tonnage). By simulation on DYNAFRAG, it was possible to discriminate among several control structures. The preferred control strategy uses a saturation algorithm, which allows the adequate regulation of two measured variables with only one actuator. Controllers located in interacting loops are appropriately tuned, taking into account the existing process coupling. Part II will present the implementation of the selected control strategy.IntroductionSteady state simulators are used to predict the stationary state of a given process under specific operating conditions. Tradi - tionally, steady state simulation has been applied for process flowsheet design, for evaluating process modification benefits or for determining key operating parameters in process operation optimization. Dynamic simulators add a new dimension to process simulation since they allow the prediction of the process transient behaviour, resulting from the application of a different set of operating conditions and/or from natural disturbances or equipment failure. Dynamic simulators can also be used for the training of new operators or for the design of control strategies."

Jan 1, 1997

By V. J. Southey

"This paper reviews the history of Wabana Mines from 1892 to 1966, inclusive, in order to clarify the essential factors involved in the achievement of maximum mining efficiency and in the search for an acceptable product to satisfy changing market requirements. It outlines the progressive steps taken to mechanize both surface and underground operations, and forecasts anticipated performance, assuming certain major plans could have been implemented. Results of extensive research in the treatment of the complex ore are discussed. Selected processing alternatives are compared as to feasibility in a summary incorporating estimated capital and operating costs."

Jan 1, 1969

By E. T. C. Spooner, Ioannou S. E.

"Abstract- The Dixie Zone Au-Ag deposit is a low sulfidation (adularia-sericite) epithermal system located 1.4 km from the producing Ken Snyder mine (7.0 M oz Au equivalent reserve/resource), Midas Mining District, north-central Nevada. This WNW striking, steep south dipping, fault system is hosted by mid-Miocene (17 Ma to 14 Ma) felsic volcanic rocks that were erupted from a vent(s) to the northeast. The system was mineralized by approximately 250 ± 20°C (n = 86), near-neutral pH, ascending fluids of predominantly meteoric origin [volatile corrected salinity = 0.52 ± 0.35 eq.wt% NaCl (n = 86)]. Bulk analytical fluid inclusion gas chromatography identified a mineralizing fluid volatile composition of 99.68 ± 0.18 mole % H2O, 0.16 ± 0.09 mole % CO2, 0.11 ± 0.05 mole percent N2, 0.05 ± 0.04 mole % CH4, and 0.01 ± 0.01 mole % CnHn+i (n = 7). Sulfur species were not analyzed due to absorption within the chromatography system; however, a H2S concentration of 16 ppm to 160 ppm molar is estimated. The volatile content contributes approximately 50% of the microthermometrically measured freezing point depression. Cl- concentrations up to approximately 9000 ppm suggest an additional, probably magmatic, fluid component.Ascending fluids were channelled along approximately NW striking faults related to the same primary extension (17 Ma to 14 Ma) responsible for Nevada basin and range physiography. Boiling induced by CO2 effervescence led to precipitation of Au and Ag over a 150 m vertical interval. At the time, this interval was about 460 m below the water table (approximately 38 bars), but because of erosion, it is now within 90 m of the surface. A Ag:Au ratio of 25:1 has been calculated for the Dixie Zone."

Jan 1, 2000

By R. Lowery

TODAY, man uses, at will, the land, the water, and the air to transport himself and his goods everywhere across the face of the world. He no longer thinks with wonder of the magic of conquering these elements - he takes his mastery of them for granted. He is, however, constantly striving to squeeze more and more efficiency from each mode of transport. Man's first method of transporting himself and his goods was, obviously, himself; then he acquired his first beast of burden - woman. Most other two-legged female animals carried their young around clinging to their fur. Human mothers were, generally speaking, furless and their offspring less 'Prehensile, and so slings and other trappings were invented to carry young children. Man's inventive genius soon adopted these devices for carrying other burdens, and for countless centuries woman carried all in order that man could walk unencumbered except by his weapons. Later other ?beasts of burden were trained and used, including dogs, horses, oxen, camels, etc. Man also discovered quite early that he could drag along the ground more than he could carry on his back.

Jan 1, 1956

By J. van Huyssteen, M. Cantor

Newmont Ghana Gold Limited's Ahafo Operation has matured from its project ramp up stage into steady state operations after three years of operation. Management focus has shifted from addressing construction and commissioning problems to optimization and improvement. This focus change has coincided with the introduction by Newmont of a Continuous Improvement (CI) program across the company which provided a project management methodology that can be used in the execution of smaller scale projects. This paper focuses on the application of CI principles at the Ahafo Plant through the discussion of several case studies that demonstrate how these principles are applied.

Jan 1, 2011

By Paul W. Billwiller

Introduction In 1937, the Britannia Mining and Smelting Company, Limited, was carrying on an extensive exploratory diamond-drilling programme. Most of this drilling was done on the 4100 level, the lowest working level in the mine. One of the exploratory diamond-drill holes, at approximately 12,500 feet from the portal of the tunnel, encountered heavily mineralized stringers of chalcopyrite and sphalerite in silicified grey schist. The mineralization was encountered just to the hanging-wall of the green mottled schist at a point 350 feet south of the 4100 tunnel. To delimit this new orebody, drifts and cross-cuts were driven on 3500, 3800, and 4100 levels to the hanging-wall in the area of the projected mineralization. On the 3500 level, the top of the mineralized zone was encountered. The zone was thoroughly explored by drifting and diamond drilling. The mineralization, however, was not sufficiently concentrated to be of commercial grade. On the 3800 level, the zone was found to consist of disconnected stringers of chalcopyrite and pyrite. Drifting was continued to the west and a long lens-shaped area of grey schist containing fairly heavy stringers of chalcopyrite was delimited. This lens later proved to be very close to the top of the commercial mineralization of the No. 8 orebody. On the 4100 level, a diagonal cross-cut was driven to the footwall of the downward projection of the mineralized zone. Diamond-drill holes from this cross-cut indicated a zone of heavy mineralization. A drift was driven off the cross-cut parallel to the zone and some distance to the footwall of it. Further diamond drilling disclosed a mineralized zone approximately 300 feet long and 35 feet wide containing sphalerite, chalcopyrite, and pyrite. The foregoing development work indicated a fairly large lens of mineralization of sufficient concentration to be classed as ore between the 4100 and 3800 levels. To explore this mineralization at depth, long diamond drill holes, dipping at minus 57° and minus 80°, were planned from some point to the hanging-wall of the orebody. The 4100 level was not suitable for small development headings, due to wider gauge track and larger cars than on the levels above. Therefore, a raise was driven from the diagonal cross-cut on the 4100 level to a point some 70 feet above and just inside the footwall of the orebody. From the top of the raise, drifts were expanded east and west to delimit the ore zone. In addition, a long cross-cut was driven 350 feet to the hanging-wall, and drifts were opened east and west from the end of the cross-cut to provide diamond-drill stations for the exploration of the orebody at depth.

Jan 1, 1946

By J. B. De Hart

This paper has been confined to the consideration of the working of thick seams, from six feet to sixteen feet, which are pitching at about thirty degrees to the horizontal. The discussion has been limited to these set conditions because they are the ones of commonest occurrence in the Southern Alberta bituminous coal district, because, from the point of view of safety, thin seams are more easily worked, and because a discussion of all the possible combinations of thick and thin seams pitching at angles varying from zero to ninety degrees with the horizontal would involve a task impossible in the time available. It has been assumed that the mine makes gas freely and that the coal is friable and tends to make inflammable dust which is highly explosive. Since the problem requires the taking into account means of maintaining a high proportion of lump coal, it is further assumed that lump coal commands a price considerably higher than the price which can be obtained for run-of-mine or for slack coal. Figure 1, tabulating the various factors which must be considered and their relation to each other, indicates diagrammatically the complexity of the problem. Any method of working becomes divided into two distinct components, the active workings of the mine and the old abandoned workings. While these are in a measure distinct, they are nevertheless inter-related, as shown in the diagram.

Jan 1, 1930

By K. Muehlenbachs, J. U. Stemler

"Abstract - The Boston deposit is a recently discovered Archean lode-gold deposit located approximately 700 km northeast of Yellowknife, in the southern portion of the Hope Bay volcanic belt. Primary H2O-CO2-NaCl fluid inclusions associated with gold mineralization at Boston are of low salinity (4.6 ± 1.4 eq. wt.% NaCl, n = 182) and contain pure CO2. Homogenization temperatures of liquid-phase inclusions average 270° ± 33°C (n = 141), but some fluid inclusion assemblages contain coexisting liquid- and vapor-phase inclusions that homogenize near critical conditions, suggesting phase separation. In these groups, liquid-phase inclusions homogenized at 299° ± 25°C (n = 24), and vapor-phase inclusions homogenized at 338° ± 28°C (n = 18). These temperatures overlap within error, and a median temperature of ~320°C is taken as representative of trapping conditions within the veins. An approximate pressure of 2-3 kbar was estimated from fluid inclusion isochores at this temperature. Stable isotopic compositions of carbonate minerals from the mineralized zones range from -4.7‰ to -3.1‰ in d13C, and from 11.2‰ to 12.8‰ in d18O; quartz ranges from d18O = 12.8‰ to 14.9‰; and pyrite ranges from d34S = 2.1‰ to 3.5‰. The d18OH2O, d13CCO2, and d34SH2S values of the fluid calculated from these minerals at 320°C are 6‰-9‰, -2.4‰ ± 0.6‰, and 1.5‰ ± 0.5‰, respectively, and are intermediate between metamorphic and magmatic compositions. A unique source for the fluids cannot, therefore, be constrained from these data. Petrographic and geochemical data for the Boston deposit are consistent with data from other Archean lode-gold deposits worldwide, implying that the Boston deposit formed in a similar environment and from similar types of fluids. These results suggest that the Hope Bay volcanic belt may represent a major new mesothermal gold belt in this part of Nunavut. Sommaire - Le gîte Boston a été récemment découvert à environ 700 km au nord-est de Yellowknife dans la partie sud de la ceinture volcanique de Hope Bay, il s’agit d’un gîte d’or filonien d’âge Archéen. Les inclusions fluides primaires de H2O-CO2-NaCl associées à la minéralisation aurifère du gîte Boston présentent une faible salinité (4.6 ± 1.4 eq. pds.% NaCl, n = 182) et contiennent du CO2 pur. La température d’homogénéisation des inclusions à phase liquide est en moyenne de 270° ± 33°C (n = 141), mais certains assemblages d’inclusions contiennent des phases liquides et gazeuses coexistantes qui s’homogénéisent dans des conditions quasi critiques, suggérant qu’elles résultent d’une séparation de phase. Dans ces groupes, les inclusions de phase liquide s’homogénéisent à 299° ± 25°C (n = 24) et les inclusions de phase gazeuse s’homogénéisent à 338° ± 28°C (n = 18). Ces températures se recoupent à l’intérieur des limites de l'erreur de mesure, et nous considérons qu’une température médiane de ~320°C est représentative des conditions de piégeage dans ces veines. Les isochores permettent d’estimer une pression d’environ 2-3 kbar à cette température. La composition des isotopes stables des carbonates dans les zones minéralisées s’étend de -4.7‰ to -3.1‰ pour d13C et pour de 11.2‰ à 12.8‰ pour d18O; les valeurs de d18O pour le quartz varient de 12.8‰ à 14.9; et les valeurs de d34S dans la pyrite vont de 2.1‰ à 3.5‰. Les valeurs de d18OH2O, d13CCO2, et d34SH2S du fluide calculé à partir de ces minéraux à une température de 320°C est de 6-9‰, -2.4‰ ± 0.6‰, et 1.5‰ ± 0.5‰ respectivement, reflétant des conditions intermédiaires entre des compositions métamorphiques et magmatiques. Il n’est donc pas possible d’identifier une source unique pour ces fluides à partir de ces données. Les données pétrographiques et géochimiques du gîte Boston sont similaires à celles d’autres gîtes d’or filoniens ailleurs dans le monde, ce qui implique que le gîte Boston s’est formé dans un environnement similaire à partir des mêmes types de fluides. Ces résultats suggèrent que la ceinture volcanique de Hope"

Jan 1, 2006

By A. Mitrašinovic, A. Wolf

"The aim of this investigation was to determine the most suitable additive for recovering metals from converter slags generated during Ni extraction. Fluxes analyzed were silica and lime and reductants included pig iron, ferrosilicon and copper-silicon compound. Slag was settled at 1300°C for one hour to simulate the smelting environment. The newly formed matte and slag were characterized by chemical composition and morphology. Microstructural studies showed that slag formed after adding reductants consisted of primarily fayalite, with traces of magnetite. Entrained matte was present in the slag mostly as prills of Ni3S2-FeS matrix and a Cu2S-FeS secondary phase below 10µm in diameter. Kinetic parameters of matte formation, valuable metal recovery rates and partition coefficients were deduced. Silica additions generated higher partition coefficients for copper and nickel than the addition of lime. Additives used as reducing agents had higher valuable metal recovery rates and partition coefficients. Silica additions favoured the formation a higher grade matte while lime additions will hinder metal recovery. Pig iron, ferrosilicon and Cu30Si were the most effective reductants for valuable metals recovery. Cu10Si and coke additions had little to no effect on valuable metals recovery."

Jan 1, 2015

By Evelynn Stirling

Agenda ? Emissions legislation ? Cummins Tier 4 Technology ? Cummins Experience with Technology ? Operation and Maintenance Impact The Emissions Challenge ? The 2014/5 emissions regulations present the most significant challenge to our customer?s diesel powered equipment design and operation in recent history? ? ?and Cummins has the solution.

Aug 1, 2013

By W. P. Campbell

Foreword At the outset, it should be stated that this paper does not pretend to present a panacea for the ills that 'frozen' wells are heir to, but rather is an attempt to bring to the attention of those whose special concern it is, a little theory and some facts, which have been brought to light recently, in connection with the problem of 'freezing' as it applies to naphtha-producing wells in the Turner Valley field, and to draw some conclusions that follow from the facts discovered. It should also be stated that the investigation is not to be regarded as in any sense complete, but in progress. Doubtless new facts will be brought to light from time to time which may modify present ideas on the subject, but whether favourable or contrary, these will be welcomed, as the purpose of the Department is to secure as complete information as possible of the factors contributing to 'freezing', since this must be the first step to an intelligent attempt to remedy or prevent its occurrence, if such can be done. It is possible, too, that the cause or causes of freezing may not be the same in all cases, but whether this be so or not will have to be determined later as new information comes to hand. Introduction One of the worries which must constantly confront the operators of gas-naphtha producing wells in Turner Valley-although all, fortunately, have not met with it-is the possibility of the occurrence of what is commonly called 'freezing' (going off production).

Jan 1, 1930

By T. L. McCall

A short description of mining practice in the Sydney coal field in general is followed by a discussion of the operations in the No. 12 colliery of the Dominion Coal Company, Limited, as being typical of the trend in operating methods obtaining throughout the field. Development of longwall mining to the present system of three walls in line is outlined, together with a summary of the cycle of operations involved in systematic operation.

Jan 1, 1944