Search Documents

By Leslie F. Sawatsky

Each potential oil sands developer deals with the question of optional sources of raw water to supply large water demands that range from 50 to 80 million cubic metres per year for each of six existing and planned developments. The Athabasca River currently supplies nearly all of the water to the existing mines via conventional bank intakes, which has resulted in some concern over the effects of reduced river flows. This paper describes the various water supply options, and the likely scenario for future oil sands water supply projects. Various water supply options have been suggested including Athabasca River water via infiltration galleries, groundwater, combined Athabasca River water and alluvial groundwater using wells (i.e. bank filtration systems), diversion of tributary rivers, utilization of large lakes in the region and pumping from other large rivers in the region. Investigations show that the size of river catchment needed to support raw water usage by a typical oil sands mines exceeds 5,000 km2 eliminating all tributary rivers that are located in the oil sands region except those rivers with large drainage areas like Firebag and MacKay Rivers. Lakes cannot be used as a source of supply due to large water deficits for smaller lakes and the large cost of sourcing water from a lake as large as Lake Athabasca. A groundwater source alone would not likely meet the large water demands. River intakes on the Athabasca River will likely continue to be the most practical water supply option for oil sands mines north of Fort McMurray, although various types of Athabasca River intakes are possible. Existing intake systems include screened riverbank intakes, forebay intakes, and river bottom intakes. Infiltration galleries are not feasible for most sites, though some bank-filtration-type systems using high capacity wells may be an option if there is sufficient thickness of high-permeability alluvium at a suitable location in the Athabasca River valley.

May 1, 2004

By A. J. Faulds, K. C. Westaway, Z. Waszczylo

"PAH compounds have been found in the exhaust from all types of engines burning hydrocarbon fuels . They have also been found in the air over cities and in water. The authors report on a study to assess the concentrations of twelve different PAH compounds in several different environments in dieselized underground mines. In addition, the differences in the PAH levels and distributions in different mines will be demonstrated. Finally, the influence of blasting and the type of diesel engine used as well as the effect of catalytic converters in the exhaust system on the PAH concentration in the mine will be discussed.IntroductionMining methods have been altered significantly in the last 25 years; i.e ., the tools and machinery used underground have changed from electrically operated trains and other equipment to diesel-powered equipment. This has been done for several reasons: 1) economics, 2) convenience and 3) safety. Today, most mines are heavily committed to using diesel equipment.Although the introduction of diesel equipment has revolutionized mining methods and has been a tremendous boon to the mining industry, it has also created new problems. These problems arise because the exhaust from diesel engines contains several pollutants which can be hazardous to the health of the miners. These pollutants are CO2, CO, NO., SO2, oxygenated hydrocarbons produced during the buring process and unburned hydrocarbons. There are two classes of hydrocarbons, of which polynuclear aromatic hydrocarbons (PAHs or PNAs) are a part."

Jan 1, 1981

By E. T. W. Bailey

A HISTOR Y of the development and application of instruments, from the simplest U gauge to a modern indicating recording controller, would contain many interesting accounts of difficulties experienced and over-come. Important as is the history of development to any branch of science, this phase will, of necessity, have to be omitted from this paper and remarks confined to the results from the use of instruments in their present form. The steel industry bas, in the past decade, become increasingly instrument minded. More than ever, economy and adherence to doser specifications are demanded, and any tool that will aid in attaining these objectives by intelligent application and use finds a ready acceptance. The open-hearth furnace bas offered a field for instruments which is different from almost any other and one in which even a small percentage saved in operating costs may represent a considerable sum. Nevertheless, this department of the steel industry has been more cautions than most others in accepting the benefits which automatic control bas given on many other types of industrial furnaces, and one is puzzled why open hearths have not more generally benefited by the application of controlling instruments. The furnace operator bas to adjust the same three main valves that control fuel, combustion air, and stack draft as on most other furnaces, with the additional regulation of reversing the furnace. He is just as aware of the importance of proper draft control and correct air volume to burn most economically the applied fuel as any good boiler-plant engineer. What, then, are the special conditions that pertain to the open-hearth furnace?

Jan 1, 1939

By Paul L. Broughton

"IntroductionThe coal deposits, all of lignite rank, of economic interest in Saskatchewan are associated with the Ravenscrag Formation (Paleocene). Several Cretaceous formations have less significant lignite accumulations (Broughton, Irvine and W'hitaker, 1974). The Swan River Group (lower Cretaceous) and Judith River Formation (upper Cretaceous) have the only coalbearing strata in the shallow subsurface of central Saskatchewan. The Swan River Group coalfield is relatively small and underlies only 15 sq km of the surface approximately 40 km south of La Ronge, Saskatchewan. An estimated 36 billion short tons are within 45 m of the surface. No reserve estimates are known to have been calculated for the coal-bearing Judith River Formation exposed at the surface in the vicinity of the South Saskatchewan River valley in west-central Saskatchewan. Although no coalfields have been delineated, lignite beds up to 1.8 m thick have been intersected in test holes. The coal-bearing upper Cretaceous and lower Tertiary strata of the northern Williston Basin extends the full width of southern Saskatchewan for 650 km, and from the United States border 120 km north to 50° latitude (Fig. 1). Only the coalfields of the Ravenscrag Formation, because of their economic interest, will be considered further. There are four major coalfields. They are, from east to west: Estevan, Willow Bunch, Wood Mountain and Shaunavon (Cypress) coalfields. Cumulative lignite seam thickness for each basin is 10 -15 m (Figs. 2 and 3). The origin of each coal basin, resource calculations, seam stratigraphy, and mining activity are discussed. Regional Setting The Williston Basin is an ellipsoidal depression in the Precambrian basement, centered in western North Dakota and marginal to the exposed craton of northern Saskatchewan and central Manitoba (Fig. 1). The sediments of the basin range from Cambrian to Pleistocene in age and have a maximum known thickness of 4614 min western North Dakota. A maximum of 3200 m is recorded in southern Saskatchewan. Most structural deformation is late Cretaceous to early Tertiary (Paleocene) in age, coinciding with the Laramide Orogeny. The pre-Laramide Williston Basin, with a depocenter near Williston, North Dakota, began developing during the middle Ordovician, or possibly earlier."

Jan 1, 1985

By Karim El-Ouassiti, Marc Minville, Stéphane Chabot, Claude Bazin, Valérie Ouellet

"Alumina is the main source of aluminium and it is extracted almost exclusively from bauxite ores found in the Southern hemisphere. Clays are abundant minerals that contain from 15 to 40% w/w of alumina from which it can be extracted by various processes. This paper reviews the processes used for the extraction of alumina from clays and discusses results obtained with a clay sample from the Murdochville area in the Quebec Province. The application of a conventional process to this clay did not yield an acceptable recovery although smelter grade alumina was produced. A modification to the process allows increasing alumina recovery from 85% to more than 92%. The application of the improved flow sheet to other alumina carriers failed to yield comparable recovery, showing that an optimum processing path for the recovery of alumina should be found for individual clay materials.INTRODUCTIONMost of the aluminium smelters are fed with alumina extracted from bauxite found in the Southern hemisphere. Bauxite is processed by the Bayer process that uses a caustic leach of the ore. In the middle of the century, the US Bureau of mines, motivated by the fear of an alumina delivery disruption, conducted several research projects aiming at producing alumina from non bauxitic ores. These projects led to the development of various acid leaching processes (Habashi, 1993). The sulphuric and hydrochloric acid leaching processes were brought to pilot plant evaluation (Bengtson, 1979), while nitric and other leach liquors were tested in the laboratory (Phillips and Wills, 1982; Habashi, 1983). Although clays are abundant and inexpensive minerals, the studied processes remained uncompetitive with the alumina extraction from bauxite (Hudson, 1987 page 42; Peters et al., 1962) for which reserves are estimated to support alumina production for the next 50 years (Oye et al., 1999). On the other hand, the local extraction of alumina from clays could significantly reduce the transportation costs of alumina to smelters and provide an alternative source of alumina supply from the Southern hemisphere countries. Also, the extraction of secondary products for some types of clay (Nasyrov et al., 1999) containing significant amounts of potassium and sodium could provide an additional return that may improve the economics of alumina production from clays."

Jan 1, 2005

By S P. Giambra

The 50,000-ton-per-day Concentrator and Crushing Plant, complete with its related water supply, tailings disposal and concentrate handling systems, was started up in a five-month period, with the entire plant obtaining its design capacity six months after the first mill became operational. Individual mill lines, with their spiral circuits, achieved design capacities within a week after the first treatment of ore through each mill. Construction and start-up proceeded together in many areas of the plant, and considerable organization and cooperation between the Owner, the Engineer and the Contractors permitted a smooth transition from construction to operation. PLANT DESCRIPTION THE Carol Lake Plant of the Iron Ore Company of Canada l1as been well described in various technical magazines. The purpose of this paper is to present a brief outline of the start-up of the con-centration complex. This start-up was accomplished in a period of five months, with the plant producing one million tons of concentrate and achieving its design-rated tonnage less than six months after the first ore was treated.

Jan 1, 1963

By R. Laplante, P. Radziszewski, P. De Ciccio

"Predicting the effect of wear can lead to improved control strategies that can possibly minimize the risk of catastrophic failure due to wear while maximizing useable life. In the field of geological exploration, diamond drill rod wear illustrates just such a case. Wear conditions vary with geological formations and compositions. The objective of this paper is to determine a general relationship, based in theory and practice, that will approximate drill rod wear and therefore predict remaining drill rod life in the context of Canadian, Australian and South American drilling campaigns. Simulation results allow the definition of simple graphical tools that permit the estimation of the potential drill depth remaining on a given drill rod string. IntroductionWear, in many industrial processes, is an undesired phenomenon for which enormous efforts are made to control, if not eliminate. However, wear, in many other cases, is an intrinsic phenomenon of the given process. In such cases, predicting the effect of wear can lead to improved control strategies that can possibly minimize the risk of catastrophic failure due to wear while maximizing useable life. In the field of geological exploration, diamond drill rod wear illustrates just such a case where abrasive conditions vary with geological formations and compositions.A number of studies have been published on drill rod wear especially with regards to the petroleum industry over the last thirty years (Lewis, 1968; Rollins, 1968; Smith, 1978; White 1978; Rowe and Wilson, 1981; Cheng, 1982; Eustes, 1986; Dudman et al., 1989; Besaisow et al., 1990). Of these, most studies covered management techniques (Rollins, 1968; Smith, 1978; White, 1978; Rowe and Wilson, 1981; Besaisow et al., 1990) and some described case histories (Cheng, 1982; Eustes, 1986; Dudman et al., 1989). However, little (Lewis, 1968) was presented that could aid in predicting wear in the particular case of diamond drilling in the metal mining industry.The objective of this paper is to determine a general relationship, based in theory and practice, that will approximate diamond drill rod wear and therefore predict remaining drill rod life in the context of Canadian, Australian and South American diamond drilling campaigns."

Jan 1, 2002

By Nordau R. Goodman

"IntroductionTHE HISTORY of Nova Scotia's gypsum industry goes back about two hundred years. The extensive deposits found in the Windsor formation, which is Lower Carboniferous, were the first discovered in North America and were known to the earliest .settlers. There has been a steady increase in production from these beds, except for minor setbacks in years of wars and depressions, but at the same time there has been a decrease in the number of operating quarries. This decrease reflects the change from the days of horse-and-cart recovery to the modern, large-scale, highly mechanized operations. In the beginning, almost any outcrop could •supply the tonnage requirements and the most •convenient were selected, but the millions of tons needed to meet present-day needs are not easily found.Despite the size and importance of the Nova Scotian deposits there has been little detailed geological work. Sir Charles Lyell, in 1843 ( 10), established that the beds are Lower Carboniferous and this was confirmed by Sir William Dawson (3) a .few years later. Both Lyell and Dawson agreed the calcium sulphate beds were an original part of a bedded series .but did not consider they resulted from a concentration of sea water. Lyell reached the conclusion that the gypsum was related to volcanic action in the form of heated vapours or hot springs. Dawson believed it was formed by the action •of sulphuric acid on calcium carbonate. The acid, derived from the oxidation •of iron pyrites which was abundant in the older formations, was carried by rivers into basins which were rich in shells."

Jan 1, 1954

By M. Choy, A. Kadiayi, E. Magdzinski

"Design of engineering controls to limit occupational noise exposure rely on accurate calculation inputs. Sound in mines can carry considerable distances. Mine ventilation engineers rely on noise propagation calculations to estimate silencer performance criteria for key mine fan installations that are often in proximity to occupied areas of a mine and can remain in service for decades. The blasted and rockbolted walls of hard rock mining tunnels have unique acoustical properties. Underground testing in an operating metal mine in Sudbury, Canada was performed and results processed to characterize noise propagation in mines, with the goal of improving the accuracy of noise calculations.INTRODUCTIONAs mine operators continue to improve and promote workplace safety, addressing noise at fixed infrastructure locations is observed as increasingly common. Underground fans are important to consider in this context, as they are typically loud, in proximity to occupied and sensitive workplaces, and operate nearly continuously. Predicting noise propagation from ventilation fans within underground mines has long been a challenge, with few available resources documenting acoustical properties as calculation inputs. Other factors in addition to rock face absorption properties include tunnel geometry and distance from the fan, which play critical roles in characterizing the noise level at any given point away from the fan. By understanding and establishing methods to better predict noise dissipation along underground mining tunnels, engineers can design noise controls with a greater degree of precision and confidence to effectively protect workers from over exposure to noise.This paper investigates classical methods of predicting reverberant room and direct field noise propagation. These prediction methods are then compared to noise measurements taken within the Fraser Mine of Glencore’s Sudbury Integrated Nickel Operations (Sudbury INO) Measurements were taken at a depth of ~881 m (2,889 ft), along an ~300 m (984 ft) long blasted hard rock mining tunnel. The noise along the mine tunnel resulted from the intakes of two 900 kW (1,200 hp) ventilation fans with a combined exhaust capacity of 300 m3/s (630,000 cfm)."

Jan 1, 2019

By R. E. Molnar, P. A. Riveros, V. M. McNamara

"This paper describes some recent research done at CANMET in the areas of ion exchange and A VR (Acidification- Volatilization Reneutralization), as applied to the recovery of gold and cyanide, respectively. It also discusses the ways in which these two technologies may be combined in order to minimize the environmental impact of gold milling operations and optimize reagent usage. IntroductionGold milling operations can essentially be divided into those that carry out a liquid/solid separation after leaching and those that recover gold directly from a leach pulp. The former produce a barren solution which may contain considerable amounts of cyanide, either free or cornplexed with metals. The latter produce a similar solution but this is now part of a slurry rather than a clear stream. Due to its toxicity, any excess cyanide must be destroyed before the effluent is discharged into the environment. Ideally, this should be (and sometimes is) accomplished by natural degradation. However, in many cases natural degradation alone cannot remove the last traces of rnetallocyanide compounds from the effluent and , as a result, most Canadian gold producers utilize a supplementary chemical oxidation system. This not only increases the operating costs, but concerns have also arisen in recent years about the formation of ammonia as a result of the chemical oxidation of cyanide (via CN--CNO--HCNO-NH3) ·"

Jan 1, 1993

By J. J. Quinn

Several mineral flotation plants utilize process water with high soluble salt content. The processing of semi-soluble minerals, the use of recycle streams, sea or well water give rise to this situation. It is unclear as to the overall effect on flotation response though there does seem to be evidence of bubble size reduction, increased froth stability and reduced reagent dosage. The present work aims to quantify the effects of salts present in process water on gas dispersion (bubble size and gas holdup) and froth properties. The salts examined were NaCI, CaCl2, Na2SO4, Na2S2O3 and Al2(SO4)3. Tests were conducted to determine the effects of salt type and concentration on gas holdup and bubble size distribution. The salts containing multivalent ions had a greater impact than the monovalent ions, in keeping with the literature. A relationship between gas holdup and ionic strength was established. The concentration of frother (methyl isobutyl carbinol, MIBC) giving equivalent gas holdup was determined. The effect of salt and frother combinations was also explored.Proposed mechanisms for coalescence inhibition in salt solutions are briefly reviewed in light of the current findings.

Jan 1, 2006

By SangHyeok Han

Selecting the best possible cranes and identifying spatial conflict-free locations on sites can result in productivity and safety improvements for large-scale industrial construction projects. In the current practice, experienced lift engineers select cranes based on the heaviest lift and/or the largest lifting radius of the identified crane. This practice is relatively time-consuming, and optimization of the crane?s use and location is also difficult. There are many factors which need to be considered during the crane selection process, a reality which further complicates the process. This paper presents a framework which aims at developing a decision support system to enhance the crane selection process and collision-free path planning for large-scale construction projects. This paper utilizes an innovative crane selection matrix in order to establish a process for optimized crane selection for construction projects. The study considers more than 40 different factors in order to reduce time and improve safety for crane operations. Following finalization of crane type (mobile crane versus tower crane), a visualization model to simulate crane operation and identify collision-free crane operation paths is proposed. This process can assist project managers to plan the lifting process more effectively and efficiently. A case study-based approach was utilized to demonstrate the proposed methodology. The methodology was tested in the planning and construction process for boiler house structures in Mannheim, Germany. The project entailed numerous challenges: one of the major tasks was to lift a 102-ton load on the top of the boiler structure through crane collaboration; space limitations on site also presented several challenges related to crane selection, location, and operation processes. Based on the project constraints, the proposed crane selection framework, and the visualization models, two tower cranes were selected and successfully implemented in the case study.

Aug 1, 2013

By Celine Y. Zhang, Chloe J. Feng, Charles Q. Jia, Donald W. Kirk

Oil sands petroleum coke (OSPC) is a by-product of coking - a high-temperature process that converts the mined bitumen to the synthetic crude oil (SCO). For every barrel of the SCO produced, about 20 kg of OSPC are generated. Over 70 million metric tons of OSPC have been produced and stockpiled as a result of the development of oil sands industry in the past few decades. Unlike conventional petroleum coke, OSPC has uniquely high impurity contents, particularly sulphur (~ 7 wt%) and metals (e.g. vanadium at ~0.15 wt%), which has hindered its large-scale applications as a solid fuel. Vanadium is a valuable metal that is widely used as an alloy for strengthening steels. The stockpiled OSPC contains about 100,000 tons of vanadium, while the world’s production in 2013 was only 75,600 tons. At the current price of $25US/kg, the OSPC-bound vanadium represents a total value of $2.5 billion US dollars. In this work, we investigate the technical feasibility of extracting vanadium from OSPC. The work focuses on the characterization of vanadium in OSPC and the conditions for effective extraction of vanadium from the OSPC.

Jan 1, 2015

By D. H. Flather, J. W. Hendry, K. Drover

Black Hawk Mining Inc. has completed a comprehensive program on the prediction and management of acid rock drainage (ARD) at their Keystone Gold Mine (Keystone) near Lynn Lake, Manitoba. The program, initiated in 1994, followed a phased approach utilizing initial acid-base accounting (ABA) results and subsequent laboratory kinetic testwork to define site-specific sulphide oxidation and neutralization consumption rates in waste rock. Net acid generating waste rock at Keystone was defined through the kinetic testwork as waste rock yielding a net potential ratio (NPR) of less than two. A preliminary waste rock management program based on blending of potentially acid generating and acid neutralizing waste rock was advanced. Subsequent refinement of the management program followed the analysis of over 1580 ABA samples collected from individual blast holes during the initial bench development phase of the Keystone pit. Uncertainties in actually achieving adequate blending within the dumps at a mining- scale resulted in the development of a revised waste rock management program based on segregation. Recognizing that any successful management plan requires that the ARD characteristics of the waste rock be identified prior to in-pit blasting, the extensive ABA database was utilized to develop a rapid characterization scheme. By implementing a characterization scheme based on total sulphur concentrations and fizz rating, waste rock could be quickly segregated without delaying the natural flow of ore from the pit. Interestingly, it also became apparent that gold values were strongly correlated with total sulphur, such that traditional fire assays were supplanted with a simple and more cost-effective total sulphur determination. The program highlights the importance and benefits of collecting and exploiting data beyond that necessary to acquire appropriate development permits.

Jan 1, 2000

By Balmer Neilly

To one with so little experience in matters pertaining to currency, international finance, and foreign trade, this is surely an ambitions venture on my part. However, this is a subject of prime importance to all seriously minded Canadians and, if we are to obtain any clear understanding of the factors involved, we must study the facts and debate such points as may remain at issue. During the last few years, the world' s better known economists have described the gold standard in all its ramifications and in such detail as to leave many of us even more confused than before. If we, then, are to acquire any real conception of its meaning and use, I think we must reduce it to its fundamentals and start from there. To my way of thinking, gold in ? trade and commerce is the symbol of honesty. When you seek to discharge a debt by tendering paper you hand the recipient an I.O.U. which may or may not be good, for the purchase of goods or services to the extent of its face value. When, however, you discharge a debt by the payment of gold, it constitutes a complete and final discharge. There are no reservations - no ifs and ands - and the transaction is definitely closed to the satisfaction of all concerned. Gold, then, is evidence of accumulated and transferable wealth that is immediately acceptable in practically every part of the world. However, there is not nearly enough gold to meet the demands of world trade, and. many years ago this deficiency gave rise to what we now describe as our banking system.

Jan 1, 1949

By Ashu Garg, Anirban Bhattacharya

"Friction stir spot welding of aluminum alloy AA6061-T6 sheets was performed with circular (plunge depths 0.4 and 0.6 mm), square and triangular tool pin (plunge depth 0.4 mm) with constant 0.2 mm shoulder penetration to characterize various zones of weld nugget. It was observed that the depth of the stir zone formed below the tool pin is comparatively similar for different tool pins but wider for circular tool pin. The size of another stir zone formed at the interface of tool pin and a tool shoulder is observed to be larger for triangular and square tool pin due to the higher swept rate. Predicted strain from finite element analysis, calculated strain rate using Zener-Hollomon relationship and experimentally measured grain size distribution indicates severe amount of plastic deformation in-and-around the nugget/spot region. Finer grains in various stir zones were observed than thermo-mechanically and heat affected zones. Grain size (at distribution peaks) in stir zones varied around 2.54 µm to 3.69 µm for different tool pin profiles as compared to base metal grain size of 20 µm. Microhardness results indicate that the welded region is quite softened than base metal and maximum hardness is mostly observed around the thermo-mechanically affected zone.INTRODUCTION Friction stir spot welding (FSSW) is widely used for joining the sheets of materials like aluminum, copper, magnesium, etc. The process begins by plunging a rotating tool (generally having a pin and a shoulder) into the sheets to be welded. Continuous stirring of the tool and downward plunging force generates localized heat due to friction at the tool-sheet interface and plastic deformation of the sheet metal. The material gets softened and the plasticized material adjacent to the tool pin starts flowing due to the action of tool rotation and tool plunge thereby causing intermixing and bonding between the overlapped sheets. The tool stirring also promotes grain refinement in the weld nugget associated with high strain, strain rate and thermal cycle. The formation of new microstructure also affects the mechanical properties and efficiency of FSSW joints. Studies also showed that the tool pin design and tool shoulder feature exerts a noteworthy influence on the material flow and intermixing during the FSSW process (Reilly et al., 2015; Hirasawa et al., 2010). Sarkar et al. (2016) studied the material flow and intermixing during FSSW using tracer material method and reported that the size and width of flow zone increases with tool penetration depth. The influence of tool rotational speed on microstructure and stir zone temperature was investigated during FSSW of dissimilar AA6061-AA5754 alloys (Gerlich et al., 2007). They reported that the average grain size in stir zone of AA6061 weld increases with increase in tool rotational speed. In another work, Gerlich et al. (2008) studied the local melting and tool slippage during FSSW of Al alloys. Tool slippage was investigated by calculating the strain rate using Zener-Hollomon relation. Garg and Bhattacharya (2017a) studied the effect of dwell time, tool pin profiles and tool rotational speed on shear strength, microstructure, temperature and strain distribution during FSSW of AA6061. In another work, Garg and Bhattacharya (2017b) analyzed the effect of different tool pins and pinless tools on the shear strength and microstructure during similar and dissimilar FSSW of AA6061-T6 and pure Cu. Chang et al. (2004) proposed mathematical relationship between the average grain size and Zener-Hollomon parameter during friction stir processing of Mg alloy. Solhjoo (2010) presented a mathematical approach to determine the critical strain as a function of peak strain required for initiation of dynamic recrystallization in austenitic stainless steel. Fratini and Buffa (2005) also proposed the numerical model to determine the grain size during continuous dynamic recrystallization phenomenon."

Jan 1, 2018

By P. C. Parsons, G. C. Milligan

"IN FIELD WORK in the Cape Breton Highlands, which are heavily covered with vegetation, it is necessary to run traverses along the valleys of small brooks. We encountered difficulty in closing such traverses, and the following technique was developed to solve this problem. It has been tested in the field for four seasons by several people, and found to be simple, efficient and more accurate than any other compass-and-pace system of which we are aware. So far as we can find, the technique has not been described previously. It may be of use to others.The Cape Breton Highlands of Nova Scotia consist of hills of old intrusive and metamorphosed sedimentary rocks protruding up to 1,000 feet above the general level of the younger sediments which underlie the valleys. The flat hill-tops are the remnants of a plateau; drainage off the edge of this plateau has produced many small steep brooks. They occupy valleys which are up to 800 feet deep, and V-shaped in cross section, with steep sides covered by mixed conifers and hardwoods. The stream at the bottom is rarely more than a few feet wide, with a negligible meander belt, but with many bends, rapids and falls. Visibility along the stream, in consequence, is rarely more than a few hundred feet, and in many places much less.It was found impractical to map the streams by the method of meander lines, as described in many standard surveying texts and hand-books. The limited visibility, and the numerous bends of the brooks, necessitated many corners. Every corner introduces errors. To 'close' a survey with 40 or 50 such corners proved either very time-consuming or impossible. In most cases, however, the general direction of a valley may be obtained from an aerial photograph, or by direct observation, and this became the basis of the method adopted."

Jan 1, 1971

By P. Kordi, L. Egorova, R. J. Bowell, D. Gurevich, V. Sedov, A. Mikhailov, D. A. Holwell

ABSTRACT Reconnaissance exploration in the Kuene region Namibia has included geological mapping, soil and stream sediment geochemistry, and ground geophysical methods. Copper mineralization occurs within a well-defined belt with north-northwest to south-southeast trend, parallel to the regional strike of the sedimentary rocks. The occurrences vary in size but are generally stratabound. The mineralization is centred on the transition from calcareous shale and interbedded limestone, through carbonate rocks, to quartzite. Geochemical anomalies have been identified correlating to induced polarization (IP) and magnetic anomalies. The anomalies identify one potential metallogenic zone more than 17 km in strike length.

Jan 1, 2012

By Michel Aubertin

Les digues de retenue de résidus miniers devraient être conçues de façon à supporter les charges les plus défavorables qui puissent être anticipées. Les nombreux incidents survenus au cours des dernières années à travers le monde montrent toutefois que la stabilité de ces ouvrages reste encore problématique. Les cas de rupture les plus courants sont reliés aux glissements le long des pentes, à la liquéfaction des rejets, au débordement des bassins, ainsi qu?à l'érosion régressive et de surface. Après avoir rappelé la nature et l?importance des certains incidents récents, l?origine de ces problèmes est brièvement présentée. On aborde ensuite le lien entre les critères à adopter pour la conception des ouvrages et les risques associés à leur rupture. De nouvelles avenues pour aider à contrôler certains problèmes sont enfin discutées, en mettant l?emphase sur la codisposition des roches stériles dans le parc à résidus miniers.

Nov 1, 2002

By Lauri Gregg

Key Message Energy focused Change Management Process that engages operations managers is the missing tool needed to build capacity for energy/GHG management

May 1, 2007