Search Documents

By R. W. Lawrence, J. B. Austin, P. B. Marchant, J. T. Chapman

"Biohydrometallurgy is the use of microbiological reactions to assist in the extraction of metals. Bioleaching offers an innovative alternative for the treatment of refractory gold-bearing sulphides (1). One particular cost advantage of bioleaching is the potential to enhance gold extraction after only partial sulphide oxidation. The apparent selective sulphide oxidation is more prevalent where the refractory gold is associated with arsenic and antimony (2). Oxidation of the pyrite minerals and arsenopyrite at different oxidation rates can result in high gold extractions at relatively low levels of sulphide oxidation due to preferential, or selective, oxidation of the arsenic mineral. Arsenic extraction rates in a bioleach process typically exceed the iron extraction rate. Therefore, in concentrates in which the precious metals are principally associated with arsenic minerals, liberation of the precious metals may be possible with high recoveries and less than complete sulphide oxidation. The capital and operating cost advantages of partial sulphide oxidation are inherently obvious and are briefly illustrated herein.Ultra fine milling (UFM) is another alternative for enhancing gold extraction from refractory sulphides. Some refractory gold is simply particle size sensitive and UFM can improve gold extraction without the need for costly sulphide oxidation (3). Fine grinding technology for enhanced gold recovery developed by Metprotech, South Africa, is currently producing 2 - 4 micron ground product using a single pass, stirred ball mill. Proper application engineering has ensured that plug flow occurs through the mill. Plug flow from the feed inlet at the bottom of the reactor ensures that short circuiting of feed does not occur and as a result, the mill product does not require classification.A combination of UFM as a pretreatment for bioleaching could provide a mechanism for enhanced selective sulphide biooxidation and/or increased overall gold extraction following biooxidation due to improved particle liberation ( 4). The effect of UFM on biooxidation costs will be discussed. Only sulphide concentrates are considered herein for application of UFM in combination with biooxidation."

Jan 1, 1990

By Brian Raymond

This paper will outline the problems and solutions of the new generation washeries, as well as the recent technological advances which are being considered for future coal preparation plants. The subjects to be covered will include: - reasons for considering coal preparation plants; - raw coal crushing and handling systems; - types of coal cleaning equipment being used versus new equipment being considered; - fine coal circuit sizing; - clean coal centrifuging and dewatering; - thermal dryer problems and changes; - fine refuse dewatering systems; - clean coal storage problems and changes; - materials handling within the plants; and - control systems for preparation plants. The design and integration of the various circuits that form a modern coal preparation plant have led to the creation of an exciting new field of industrial research. As the need for energy sources increases, efficient methods of preparing coals for specific markets will become more important.

Jan 1, 1979

By A. Manohar Rao

Underground mining in general and more so the coal mining is a hazardous venture as it is a struggle against nature and natural forces. The stability of roadways has a direct impact on production and productivity. The roadway stability can be strongly influenced by the direction of the drivage. The stress studies are useful to provide a frame work for understanding the influence of drivage direction on roadway conditions, and to illustrate how mapping techniques can enhance this understanding. The act of mining can concentrate and re-orient the original stresses. Whenever coal is removed, the overburden weight that it carried is transferred. Vertical stresses are similarly affected when the roof is deformed or failed. The Singareni Collieries Company Ltd., a joint Public sector undertaking of the Government of Andhra Pradesh and India is conducting coalmining operations in the Godavari Valley Coalfield and is catering to the needs of a large part of South India. With the technology update, it is looking for safe mining and to achieve higher production. As a part of this, an attempt is made to understand the stress conditions prevailing on the mine blocks by different ways and means in terms of geology, structure and tectonics of the Godavari Valley coalfield, satellite imagery studies, cleat pattern, stress measurement studies conducted in different mine blocks, and stress mapping technique.

Aug 1, 2013

By Wayne N. McKee, Scott A. Lewis

"Introduction to the Syncrude OperationSyncrude Canada Ltd., located 42 km north of the city of Fort McMurray, Alberta, (Fig. I) is an integrated operation that has produced synthetic crude oil from the Athabasca oil sand deposit since 1978.The operation, consisting of a surface mine, an extraction plant, a bitumen upgrader, and a utilities plant, is currently capable of producing over 60 million barrels of crude oil per year. Production is expected to increase to 70 million barrels of crude oil per year over the next five-year period with no major changes to equipment or process planned.The Syncrude surface mine, producing a total of 675 000 tonnes of ore and waste per day, rates as one of the largest mines in the world. A strip mining method is utilized, with two or three operating benches necessary to excavate a total depth varying between 60 m and 70 m. The 20 m to 30 m of overburden is removed by electric and hydraulic shovels and 200-ton haul trucks, and dumped in the mined-out pit for final storage. The overburden operation creates a flat bench near the top of the ore zone on which the four 60 m3 draglines operate. The draglines excavate interbanded ore and waste in the highwall, with ore placed on the operating bench in windrows, and waste returned to the mined-out pit. The windrowed ore is reclaimed by four bucketwheel reclaimers, and discharged onto a conveyor system for transfer to the extraction plant."

Jan 1, 1993

By Balakrishnan Nanthakumar, Marek Pawlik, Dennis Grimm

"The anionic flotation of a high-iron phosphate ore from Agrium - Kapuskasing Phosphate Operations was investigated through batch flotation tests in the presence of soda ash. The flotation data were supplemented by titration of the flotation pulp with soda ash, analysis of process water chemistry, and determination of the mineralogical composition of the ore. The results of lab tests were applied to the flotation circuit design allowing the flotation plant to efficiently process problematic ores. Process control measures (pH, conductivity) were also developed.Calcium cations and sulfate anions were identified as the dominant ions present in the process water when the difficult-to-process ores are beneficiated in the flotation plant. The concentrations of calcium and sulfate ions were consistent with the presence of a small amount of a calcium sulfate mineral in the ore although an oxidation/weathering process of iron sulfide minerals present in the ore could also be responsible for the observed water chemistry and subsequent flotation problems with the ores. The latter possibility suggests that the long-term stockpiling of such ores may have a highly negative impact on the flotation process.The role of soda ash in the flotation circuit is to precipitate metal cations from the pulp thus allowing the tall oil-based collector to selectively interact with the phosphate components.INTRODUCTIONPhosphorus minerals are the main source of this element for the production of fertilizers, and the froth flotation process is the most important technology for beneficiating phosphate ores. The flotation concentrate from Agrium-Kapuskasing Phosphate Operations (KPO) is transported to Redwater Fertilizer Operations in Alberta (also operated by Agrium) where the phosphate concentrate is converted into a phosphate fertilizer and other important chemical products. The KPO phosphate ores differ widely in mineralogy and phosphate grades, and are broadly divided on-site into three classes. The easy-to-float A-type ores do not pose any major flotation problems, but the B-type and “marginal” ores, which are quite common in the KPO igneous phosphate deposit, are not always readily-floatable using the current reagent suites and process parameters (pulp density, feed particle size, pH). In fact, marginal ores are presently considered impossible to process by flotation. A-type ores contain normally more than 15% P2O5 and less than 8% ferric oxide equivalent (Fe2O3). B-type ores are approximately of the same P2O5 grades as A-type ores but their iron content may reach 30% Fe2O3. Any material containing less than 15% P2O5 is rejected as waste rock."

Jan 1, 2008

By F. E. Goodwin

Since the last CIM Zinc and Lead Conference ten years ago, significant technical and market forces have influenced how these metals are used, and the geographic distribution of their uses. Unprecedented price fluctuations have opened competitiveness issues, while the rapid growth of the Chinese market has created challenges both inside and outside China. Recent technical developments in battery energy storage, coatings, castings and chemical applications of lead and zinc will be reviewed together with the influence of these trends on end use markets.

Jan 1, 2008

By M. Lahtinen

Traditionally, there have been three main methods for iron removal in the hydrometallurgical production of zinc. These methods are atmospheric precipitation of jarosite or goethite and pressurised precipitation of hematite. Jarosite precipitation is without doubt the leading and the most commonly used technology for iron removal. However, jarosite precipitation has some drawbacks, such as a low iron content (and, thus, high residue volume), high moisture content after filtration and often a high zinc content. These features make any environmentally acceptable way of using or disposing of jarosite more expensive, as compared to hematite and goethite. The importance of environmental regulations has grown in the zinc industry during the last decade, which will have an increasing effect on new investments. Hematite has several advantages over jarosite, such as a high iron content, low moisture and low zinc content. An important advantage of hematite is that it is suited for further use in the cement industry. However, until now the need for autoclave equipment has limited the spread and implementation of hematite precipitation in the zinc industry. Outokumpu Technology Oy has recently developed an alternative method for iron removal, which is the atmospheric precipitation of hematite. A patented method for precipitating hematite at atmospheric pressure is presented and compared with conventional methods for iron removal. The process conditions, the quality of the hematite precipitate and the environmental aspects are also discussed.

Jan 1, 2006

By Brad Gunn

Our program has been dictated by the necessity of broadening our markets through converting potash chemicals to fertilizers more in demand than potassium chloride. To this end, we have undertaken studies on methods of preparing potassium sulphate or potassium magnesium sulphate by rather simple conversion. When mixtures of sodium and magnesium sulphates are reacted with potassium chloride, the ratio of sodium to magnesium is quite pertinent. A range of ratios has been selected and the conversions of potassium chloride to sulphate have been assessed by cyclic operations. Results from experimental procedures for producing potassium nitrate are also avail-able. The influence on recovery for systems including organic solvents is assessed for a variety of situations.

Jan 1, 1971

By A. L. Valdivieso

"The correlation obtained by plotting pH of maximum adsorption of dextrin versus the isoelectric point of involved metal hydroxides can be used to predict the depressing effect of dextrin on flotation in ""pure"" sulfide mineral systems. Sulfides are strongly depressed by dextrin whenever their surfaces are coated by the corresponding metal hydroxide. The efficiency of dextrin as a depressant is affected by the adsorption of the sulfhydryl collector. Hydrolyzable cations modify this relationship in flotation of sulfide ores. This type of deviation of the real-life systems from the predictions based on the behavior of the pure systems shows the possible ways that could be followed to further improve the obtained correlations. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by"

Jan 1, 2009

By C. Patel, George H. Hope

"INTRODUCTIONThe Hemlo area is located in Northern Ontario, some 350 km east of Thunder Bay along highway 17. Hemlo is Canada's largest, recent discovery of gold ore. Three companies, Lac, Noranda, and Teck are currently developing mines and processing facilities in the area. A combined milling capacity of approximately 10,000 tonnes per day will ultimately be available in the area. The gold yield will be between 750,000 to 1,000,000 ozs. per year. This will slightly more than double Ontario's gold production but only represents 2.5% of the total world gold production.Lac Minerals Ltd. is substantially committed to the gold mining business. Lac currently operates four (4) gold mines and mills and produces 300,000 ozs. per year. Lac's Hemlo development will put the company in the position of number one gold producer in Canada.The Lac Hemlo ore body has an estimated reserve of 37 million tonnes at 6.2 g/t. The mining will take place at an initial rate of 3,000 t/d commencing in the first quarter of 1986. The mine and plant will be expanded to 6,000 t/d in 1988. At this capacity, Lac will be the largest producer in the Hemlo area.1. GEOLOGYThe orebody is divided into two (2) zones for mining purposes. The 'A' Zone is to the east and dips to the Northeast from surface to 300 m below surface. This zone has a strike length of 250 m to 300 m at an average width of 20 m. The upperpart of the zone will be mined by open pit and the remainder from underground. The 'B' Zone, to the north west of the 'A' Zone, although lined up is not necessarily an extension of 'A' Zone. 'B' Zone has a known strike length of 600 m and is open to depth and along the strike. It is over 70 m wide in the core. This zone holds most of the property's known reserves. 'C' Zone with narrow gold zones is under exploration in the south west portion of the property."

Jan 1, 1985

By H. J. Ni, M. Y. Huang, S. W. Chen

The effects of several fluxes on purification, microstructures and properties of A00 aluminium have been studied. The experimental results and analyses indicate that many cracks and large porosities exist in the surface film above the melt purified by C2Cl6 and that the film is floe and mostly composed of AhO3 and pure aluminum, which carries many carbon particles and AlCh not fully volatilized. And then over 50% of the all-melting residue is pure aluminum, which is one of the major reasons for high melting loss. Moreover, because of a mass of gas bubbles and a state of seethe, there exist many inclusions which size is under l0µm in the microstructure of A00 aluminum purified with C2Cl6 or fluxes containing C2Cl6- With this purifying method, the aluminum crystal grains are extended along the radius that was observed firstly and the average crystal size of A00 aluminum are about 100µm~150µm. In addition, small size inclusions have little affected on tensile strength and micro inclusions under l0µm have little affected on elongation.

Jan 1, 2006

By Kenneth G. Thomas

Since approximately 2003 we have witnessed the unprecedented escalation in commodity prices. Coupled with economic chaos following the 2008 economic downturn this has caused difficulties in controlling schedule, capital costs and operating costs for mining projects. Once again escalation has returned to commodity prices fuelled by growth in the BRIC countries especially China and Brazil. This is further exasperated by the missing generation of skilled technical personnel not graduating from universities in the 1980s and 1990s owing to depressed commodity prices. This paper examines the six tenets for successful project implementation.

Jan 1, 2011

By W. Standifird

"Cohesive fracture is a mechanical model widely used for modeling quasi-brittle fracture in rocklike materials. This work discusses use of this model to simulate quasi-brittle fractures generated by injection stimulation during the process of cuttings reinjection in West Africa. Cuttings reinjection is an engineering practice used for disposal of drilling waste. During this process, hydraulic fractures are created at the target formation and milled cuttings are injected with fluid. In practice, this process must remain in compliance with environmental regulations and zero-discharge policies. The purpose of this study is to determine the following factors of injection design for a field in West Africa: (1) pumping pressure capacity required to successfully perform the injection and (2) the injection rate for injection performance and the value of fracture width under injection.A simplified three-dimensional (3D) finite element model (FEM) was built. A poroelastic plastic damage model was used for simulation of the cohesive crack prorogation within the target formation. For simplicity, fracture development in both horizontal and vertical directions was simulated separately. In this way, the computational burden for one calculation was reduced to a reasonably low level, without losing accuracy of the model. Loads of the model include fluid injection and gravity, which balances the initial geostress field. Various values of injection rate were used in these calculations to determine the most reasonable value of injection pressure. The capacity of pressure of a pumping device was determined using this optimized value of injection pressure.Results in values of width and length of fractures created by the injection are presented. Injection pressures at bottom-hole (BHP) corresponding to each value of injection rate are also given. Numerical results for fracture generation and propagation in a horizontal direction were visualized. The pumping pressure capacity required to fulfill the cuttings reinjection work was determined based on the numerical results of optimized injection rates and pressure. The fracture width was determined using the given pumping pressure. The length and height of the fractures was determined using pumping pressure along with the required volume of cuttings waste to be disposed of into the formation.This work presents a case study of 3D finite element modeling of hydraulic fracturing generated by cuttings reinjection. The results of the optimized injection rate and pressure provide a best practice and a useful reference for cuttings reinjection analyses in this region."

Jan 1, 2015

By D. M. Ramsey

HIGH-INTENSITY magnetic separation as now practised in the commercial treatment of a large variety of industrial minerals is a com-paratively recent development, having had its practical beginning about ten years ago when it became necessary to devise more effective methods for the purification of the electric furnace abrasives and refractories-silicon carbide and fused aluminium oxide. The fundamentals of magnetic separation are, of course, very well under-stood; bur while very, very old in principle, the process has, in recent years, been developed to a point of far greater usefulness than heretofore. In fact, until the development of the high-intensity process,. magnetic separation was limited largely to the removal of tramp iron? with magnetic pulleys and the removal of the very highly magnetic portions of industrial minerals by means of horizontal conveyor-belt-type separators. All magnetic separation processes depend for their success on the fact that various materials are kinetically influenced to a greater or lesser degree by the force that we speak of as 'magnetism'. We have now come to regard 'magnetic separation' and 'high-intensity magnetic separation' as two different and distinct methods. However, both depend upon the reaction of a particle when placed in a magnetic field. The common types of magnetic separators quite generally operate on the principle that a magnetic particle can be lifted by a powerful magnetic force from a stream of material moving on a belt or other type of conveyor. The application of the force removing magnetic material by this scheme is directly opposed to the force of gravity and is, therefore, limited to sub-stances of a relatively high order of magnetic susceptibility, such as metallic iron and magnetite. Until a few years ago, one very important principle was almost entirely overlooked. Practically every substance is susceptible to some extent, at least, to magnetic attraction, and by the application of a magnetic force great enough, and properly applied, separations of materials heretofore considered 'non-magnetic' can be accomplished.

Jan 1, 1937

By Harry Siewert, Tom Milner, Jack Stickney

"LocationThe Gibraltar mine is located in central British Columbia (NTS 93B/9W), 362 km north of Vancouver. Access is provided by 20 km of paved road from McLeese Lake, which lies 45 km north of Williams Lake on Highway 97. Latitude and longitude of the mine are 52° 30' and 122° 16', respectively.The total area of the McLeese Lake site is approximately 1700 ha (4200 acres). This includes the orebodies, dumps, surface drainage collection system, plant site, roads and tailings ponds.Brief Description of OperationOre is mined by open pit methods and is concentrated using conventional crushing, grinding and flotation processes. Copper and molybdenum flotation occurs at an average rate of 40 000 tons per day. Tailing is discharged to an impoundment area and the water recycled as process water. Additional copper is extracted from the waste dumps using sulphuric acid as a leach solution followed by solvent extraction and electrowinning.HistoryExploration by Gibraltar began in 1964, continuing until late 1970, at which time it was announced that the property would go into production. Construction started in early 1971, with initial production in March 1972. Target capacity of 30 000 tons per day was achieved by the end of March and is currently at 40 000 tons per day.Ore reserves as of January 1, 1998 were 184 384 000 tons grading 0.31% Cu and 0.010% MoS2."

Jan 1, 2000

By N. E. Nelson

"The Hidden Creek mine is about l~ miles north of the north end of Granby bay; a nearly landlocked body of water on the west side of Observatory inlet; 90 miles north of Prince Rupert; British Columbia.The main haulage way of the mine at 385 feet above sea-level has been driven north into the somewhat precipitous end of a north-south ridge that rises from the tide flats between the east and west forks of Hidden creek. The outcrops of the principal orebodies, two prominent bluffs of stained rocks and sulphides, were higher on the face of the ridge and extended from about 530 to 850 feet elevation. North from the bluff tops, the ridge comb rose gradually to about 1,200 feet elevation. The name of the discoverer and the date of discovery of the Hidden Creek orebodies are probably unknown, but the discoverer is believed to have been an Indian from one of the reservations along Observatory inlet. The deposit was brought to the attention of John Flewin, Government Agent at Post Simpson, near the beginning of the present century. Mr. M. K. Rodgers, developer of the Nickel Plate mine at Hedley, did the first organized work on the deposits. Next the Hidden Creek Copper Company prospected the property. Rodgers acquired the prospect a second time, did more work, and finally in 1910 optioned the property to the Granby Consolidated Mining, Smelting and Power Company, Limited, at that time operating at Phoenix and Grand Forks in the Boundary district of British Columbia. The optionees stepped up the development work and brought the property to production in 1914. The ores were direct smelted until 1924. In that year a mill was built. From 1930 until the end of the productive life of the properties in 1935, all of the ore was milled and the concentrate smelted. From March 17, 1914, until July 31, 1935, the production from the Hidden Creek mine was, in round numbers, 18,000,000 tons of 1.70 per cent copper ore and 6,000,000 tons of low grade dilution rock. The Hidden Creek mine ""died with its boots on"". During 1934 the average monthly production was 146,377 tons of 1.06 per cent copper ore. For 7 months of 1935 the average was 161,750 tons of 1.03 per cent ore, and for the final month, July 1935, the production was 156,950 tons."

Jan 1, 1954

By Mary A. Wells, Amir Hadadzadeh, Mark A. Whitney, Stephen F. Corbin

In an effort to produce less expensive titanium sheet via roll compaction, the room temperature compaction behavior of titanium sponge granules (99.9% pure, Alfa Aesar) was studied under uniaxial die compaction. The titanium sponge granules were irregularly shaped, with a high degree of porosity, having a maximum particle size of 3mm. Manual die compaction was conducted using a Carver hand press, in a hardened tool steel die with 12.61 mm inner diameter. Uniaxial die compaction in a hardened tool steel die with 9.50 mm inner diameter was also performed using a Gleeble® 3500 thermal-mechanical simulation testing system which allowed for controlled deformation rates. Compaction behavior of the titanium sponge was studied using well-established compaction equations (Heckel, Panelli-Filho and Ge), and it was observed that compaction rate influences the room temperature compaction behavior of this material. The Heckel analysis of the titanium sponge showed that the behavior of the material could be analyzed in two compaction pressure regimes. In the low pressure regime (<100 MPa) the granules exhibited high compressibility, while; in the high pressure regime (>100 MPa) lower compressibility of the titanium sponge was observed.

Jan 1, 2015

By Michael Samis

Conventional project valuation techniques, such as discounted cash flow (DCF) method, are more frequently being criticised for the manner in which they consider the interacting effects of uncertainty and project structure (including management flexibility) on project value. Modern asset pricing (MAP; often called ?real options valuation? when applied to the analysis of flexibility) is a more general valuation framework that corrects many of the shortcomings of common valuation methods. Previous mining applications of MAP have tended to treat the ore deposit as a homogenous entity. While useful for demonstration purposes, this is inadequate for practical application in industry. This paper presents a MAP valuation example that allows for the heterogeneous nature of an ore deposit. It shows that deposit structure may increase the complexity of the mine planner?s decision so that results of a standard DCF analysis, or a simple MAP analysis that ignores the details of deposit structure, are misleading. In the example, a management is considering the development of an adjacent low-grade zone while mining operations in a high-grade zone are ongoing. If the low-grade zone is developed before high-grade reserves are exhausted, the proposed development will include both low-grade zone development and a capacity expansion to handle additional low-grade reserve production. If development of these reserves is delayed until the high-grade reserves are depleted, then the low-grade reserves can be developed without a capacity expansion. A typical DCF analysis would reduce the management?s decision problem to three alternatives: 1) continue mining only in the highgrade reserves, 2) immediately develop the low-grade reserves and expand capacity, and 3) delay low-grade zone development until the high-grade reserves are exhausted. The model presented here allows the management to reconsider the development and capacity expansion decision on a discrete half-year basis. It delineates price regions, for given levels of high-grade zone reserves, in which it is optimal to develop the low-grade zone, defer low-grade zone development and abandon the mine irrevocably. The model presented here extends the ability of mine planners to describe actual project structure while using the MAP valuation framework that is already noted for its capacity to combine project uncertainty and risk insights with a dynamic project description.

May 1, 2001

"At a current mining rate of 3,750 tons per day, La Mine Doyon is currently the largest gold mine in Canada. La Mine Doyon is an open pit gold mine located in the Abitibi area of Northwestern Quebec. The project is a joint venture between Soquem, a Quebec Crown Corporation in the resource development field and Lac Minerals Ltd., a publicly-held, resource development company. Lac Minerals is the managing company and operator of the project.Doyon went into production in 1980 on a very limited basis at 600 tons/day, and has seen a step wise increase to the current rate of 3,750 tons/day. Initially, all the ore was processed at Noranda Mines, Horne Division as flux for the copper smelter. The East Malartic Mill in Malartic was then upgraded and began processing Doyon ore. The third step in the progressive increase of throughput was the commissioning of the Doyon mill in November of 1982. Doyon ore is currently being processed at all three locations.During 1983, an exploration ramp was driven to explore the ore below the ultimate pit depth. Current plans indicate the sinking of a shaft and the commencement of underground mining during the next 2 or 3 years.Since its humble beginning, La Mine Doyon has always been a success; ore reserves have been extended to the east and the west and will soon be confirmed at depth, the mining and processing rates have been increased 6 fold, and the recovery has been increased from a designed recovery of 85% to over 95%. The intent of this paper is to trace the history and reasons for these rather dramatic improvements."

Jan 1, 1984

By R. Grau

"After commissioning and start-up of the first 500m3 TankCell® flotation cell in 2014, the over 300m3 mechanical flotation cells have earned their place in large-scale flotation operations. These 500 to 630m3 cells, designed for projects with large throughputs, are proven to provide savings in project capital and operational expenditure through savings in foot print, energy consumption, and less equipment to install and maintain. Addition to savings in different phases of a project, these cells provides operational flexibility and has shown improvements in metallurgical performance. In this paper a case study from Kevitsa TankCell® e500 installation and Buenavista del Cobre TankCell® e630 installations will be given.INTRODUCTION After development (Grönstrand and Bourke, 2008), characterization (Morales et al. 2009; Yanez et al. 2009; Grönstrand at al. 2009), validation (Elgueta et al. 2009; Coleman and Dixon, 2010), and more than 350 industrial installations of the Outotec TankCell® e300 flotation cell, the well proven energy efficient TankCell® product family introduced the TankCell® e500 forced-air flotation cell late June 2012 (Outotec.com, 2012). The introduction of the 500 m3 flotation cell followed by introduction of a 630 m3 flotation cell, TankCell® e630, in October 2014 (Outotec.com, 2014). These large flotation cells are designed for projects with high throughputs where the number of cells needed for operation with smaller equipment would become large. The benefits of this size of flotation cells comes from the lower capital expenditures due to lower equipment costs, savings in plant footprint, less installation work with less auxiliary equipment, lower energy consumption, and less units per installation resulting in less components, spare parts and maintenance.The first TankCell® e500 was commissioned and taken into operation in October 2014 at FQML Kevitsa Cu-Ni-PGE concentrator, nowadays owned by New Boliden. The first TankCell e630 was taken into operation in January 2018 at GrupoMexico’s Buenavista del Cobre Cu-Mo concentrator. The start-ups of the first TankCell® e500 and TankCell® e630 followed with test work where the hydrodynamic performances of the cells were characterized and metallurgical performance studied. The results of the TankCell® e500 test work were presented in detail by Mattsson et al (2015a; 2015b) and TankCell® e630 by Grau et al. 2018. In this paper the metallurgical improvements achieved with the large cell installations will be presented."

Jan 1, 2019