Search Documents

By P. P. Andrieux

The recovery of the Zone G crown pillar, located between the bottom of the open pit and the top of the underground workings at the Raglan Katinniq Mine in Nunavik, started in the summer of 2008 and should be completed by the end of 2009. This article describes the rock mechanics-based approach implemented to design the recovery of this valuable block of ore. The stereophotography-based ShapeMetriX3D technique was first used to provide a comprehensive assessment of the various joint sets that comprised the pillar. Then, the statistical distributions obtained for the dip, dip direction, spacing and persistence of these sets were used in conjunction with the geometry of the large-scale faults present in the area to build and run a series of explicit rigid numerical models. Each of these models had a slightly different jointing geometry, randomly constructed from these statistical distributions. Incorporating in a properly formulated numerical model the variability of some of the input parameters has allowed the engineering team to assess in a rational and reliable manner the likelihood of success of the proposed mining method and sequence.

May 1, 2009

By Ross Byron, Ken Roberts

"During the fall of 2001 a program was initiated to determine the feasibility of improving the metallurgy in the flotation circuit at the Penhorwood Talc Concentrator located near Timmins, Ontario. Bench scale testwork led Plant staff to believe that opportunities existed to improve the flotation performance. Pilot scale testing was then conducted using two vendors and their respective cylindrical type flotation cells to indicate where these opportunities existed.The results of the test program determined that the replacement of the existing flotation circuit (roughers, scavengers and cleaners) with new flotation cells could be economically viable. Justification was due to a reduction in installed horsepower, maintenance costs and a subsequent increase in recovery and throughput while maintaining product quality. Unforeseen benefits included reagent and air reduction, accurate level control as well as improved working conditions due to the removal of the antiquated equipment and ancillaries.This paper will detail the justification, installation and implementation of the new flotation circuit. A special emphasis will explain the hurdles encountered while trying to install and commission the circuit in an operating Concentrator with minimal interruptions to production.INTRODUCTIONThe Penhorwood mine and Concentrator is 28 yrs old and has gone through many ups and downs with different owners, Johns Manville, Steetley Talc and now Luzenac. It has also been expanded twice, with flotation and grinding capacity being added in recent years.All of the concentration is completed at the mine site while the fine grinding takes place in the Timmins micronizing plant.Luzenac’s Philosophy is to be the world leader in Talc production, technology and sales, having about 70% of the current world High Grade talc market."

Jan 1, 2004

By R. C. A. Thurston

"The lack of notch ductility in structural steel in general, and in ship plate in particular, has been the object of widespread attention in the metallurgical world since the spectacular collapse of the ill-fated S.S. Schenectady in 1943. Numerous investigations have been carried out, many new tests have been developed, and a vast amount of useful data has been published, with the result that our knowledge is now far more advanced than it was at the time of this disaster. Interest has focused largely on the medium strength steels, and the various factors which cause a normally ductile steel to behave in a brittle manner in the presence of a notch and at relatively .low temperatures have been thoroughly studied.The literature available on high-tensile steels, however, is less extensive and the present paper is intended to supplement this information. Notch toughness tests have been carried out, at the request of the R.C.N., on a high-tensile manganese steel in the form of commercial ship plate. One of the newer tests, the tear test, and the Charpy V-notch impact test, were used to examine the characteristics of plate for the construction of an ice-breaker. About 250 plates, mainly in the thickness range from 11,4 in. to 1 % in., were tested. An an-alysis of the results obtained is presented, certain aspects of the tear test are discussed, and the correlation between the two types of test is studied. On the basis of information available from casualty ships, the plates, with few exceptions, were considered to be satisfactory."

Jan 1, 1959

By B. R. Johnston, K. D. Streeter

"ABSTRACTCoal Mountain Operations is the newest of Fording Coal’s operations although it is the oldest in terms of its historical production. In October, 1994, Fording purchased the former Corbin Creek/Byron Creek Mine. The mine is located in southeastern British Columbia, approximately 150 air kilometers from Calgary, Alberta. It was first developed in 1905 and has gone through a variety of owners in its 90-year history.This paper will deal with the remobilization strategy and the mining plans for the operation which are being implemented to make this operation competitive in the world export coal market. IntroductionIn October 1994, following a due diligence process, Fording Coal Limited purchased Coal Mountain Operations from Corbin Creek Resources, an employee group which had previously owned the mine. The purchase awarded Fording Coal Limited with 100% of the assets, and control of all the coal leases at Coal Mountain.The mine is located in southeastern British Columbia, southeast of Sparwood at the hamlet of Corbin, (Fig. 1).Rehiring of laid-off employees started in November 1994, with mining activities also recommencing in November. The coal preparation plant was restarted in December with one shift, went to two shifts in January 1995, and had four-shift, full-time operation in April 1996."

Jan 1, 1997

By Victor Dolmage

Introduction Although gold production in British Columbia began in 1859, lode gold was not produced till 1893. Since 1900, the annual production of lode gold has fluctuated between $3,000,000 and $6,000,000. About twenty per cent of this production may be regarded as by-product gold from base metal mining. The remainder comes from a few isolated but important mines, such as the Rossland mines, Nickel Plate, Surf Inlet, Premier, Pioneer, Bralorne, Reno, and Cariboo Gold Quartz, and from several less important mines. All of the above, except Pioneer, Bralorne, Reno, and Cariboo, are approaching or have reached the point of exhaustion, but all are now receiving, under the stimulus of the. present gold-mining boom, drastic resuscitative treatment, with, in some cases, signs of resurrection. Notwithstanding this, however, the main interest at the present time is focussed on the Bridge River and Cariboo fields. Both these fields were discovered in the early 'sixties' and, apart from the Cariboo placer production, both have from time to time contributed small amounts of lode gold; but it is only during the last two years that the real possibilities of these areas were discovered. and that they began to assume the appearance of goldfields of major importance. The two fields are sorme three hundred miles distant from one another and contain deposits of distinctly different types, so that the only reason for including them in one article is the fact that they came into prominence more or less simultaneously and at a time coinciding with, but not otherwise related to, the present gold-mining boom.

Jan 1, 1934

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 45 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonnes of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in the US and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Nov 1, 2011

By B. Yu, Y. O. Oyediran, M. Robart

"This paper presents the latest flotation development testwork conducted in 2015 on the ‘B Zone’ samples from the Strange Lake Alkalic Complex (SLAC). Since the discovery by Iron Ore Company of Canada (IOC), metallurgical development has been under taken by a number of mining companies targeting various value metals, including yttrium, zirconium, niobium, and rare earths.Most recent, Quest Rare Minerals Ltd. (Quest) completed a Pre-Feasibility Study (PFS) in 2013 where the flowsheet was relatively complex and led Quest to explore alternative options. In 2014, the PFS flowsheet was simplified and one of the features introduced was pre-concentration by rougher flotation. The combined rougher flotation concentrate and slimes successfully recovered >90% TREE in 60% mass thus reducing capital cost and technical risks of the downstream hydrometallurgical processes. The latest flotation development testwork focused on achieving a pre-concentrate in which >80% TREE are recovered in 20% mass. Two separate reagent schemes, based on an ester phosphate collector (Clariant 1682) and a benzoylhydroxamic acid collector (Florrea 7510), were developed. Parameters evaluated in the development testwork included desliming, secondary yttrium and zircon collectors, depressants, temperature, conditioning temperature, time, and density, pH, sodium silicate type, cleaning, and flowsheet configuration. Both developed reagent schemes achieved the targeted metallurgy.INTRODUCTIONThe Strange Lake Alkalic Complex (SLAC) was discovered after geological survey and mapping studies by Geological Survey of Canada and Newfoundland and Labrador Department of Natural Resources between 1967 and 1980. Subsequent exploratory drilling programs by Iron Ore Company (IOC) in the 1980s found that the REE and high field strength element (HFSE) mineralization were within the central region of the SLAC which was named A Zone by IOC and later renamed Main Zone by Quest Rare Minerals Ltd. (Quest). Additional exploratory drilling outside the Main Zone by IOC and later by Quest, led to the discovery of B Zone, which was recognized as the most significant deposit of rare earth elements, yttrium, and zirconium in the SLAC. The B Zone Indicated Resources are estimated at 278.13 Mt at 0.93% total rare earth oxide (TREO) and Inferred Mineral Resources are estimated at 214.35 Mt at 0.85% TREO (Oyediran et al., 2014)."

Jan 1, 2016

By F. Halverson

"The theory of flocculation usually is in a state of flux, involves many diverse phenomena, and is complex and sometimes contradictory in details. Instead of attempting a general discourse, I shall discuss selected observations made at our Stamford Laboratories, which impinge on theoretical aspects in two somewhat distinct areas of flocculation. Since some of you many not be familiar with flocculation, and :.n order that we all attach the same meaning to the jargon used, I first would like to review briefly a generalized picture of what goes on.Assume we have a suspension of particles in water, with a distribution in the sizes of particles. The surfaces of the particles interact to some extent with the water--· tending to alter the extent of hydration, may generate some ion exchange, all being somewhat variable with time--developing a surface condition which is very complex in details. We refer to this suspension as the ""substrate.""In the usual situation, if the suspension is allowed to stand quietly, the large particles settle out first, with somewhat smaller particles settling more slowly, and then there is a portion of very fine material which takes a long time or doesn't settle out at all. This resistance to settling t~ the very fine particles results from many factors, but all relate back to the size and density of the particles, to their surface properties, and to the other components in the aqueous suspending medium."

Jan 1, 1978

By J. G. A. Stevenson

GENERAL Location of Property THE Stirling zinc-lead-copper deposit is in Richmond county, Cape Breton, about a quarter of a mile southwest from Stirling P.O., and some 45 miles southwest from Sydney. The property is accessible by road for at least nine months of the year, and during the navigation period coastal boats maintain a service touching at the port of Fourchu, eleven miles from the mine. When flying conditions permit, the Cape Breton Flying Club, of Sydney, will carry passengers to or from the property, a service which has been particularly advantageous on two occasions when hospitalization was urgently required. The Company has mining rights on leases Nos. 73-74, 78-80, and 101-104, inclusive, and owns 166 acres at Stirling and one acre at Fourchu. The ore deposit is in lease No. 73. History The Stirling deposit was discovered in the &apos;nineties&apos;, probably about 1895. The original discovery is said to have been made in the bed of Copper creek, which traverses the ore-zone. For a number of years, indifferent development work was carried on with a view to copper production only, and it was not until1915-16 that attention was directed to the possible production of zinc. Previously, the ore had been considered too complex for metallurgical treatment. During the period 1916-24 several operators attempted to develop the property, among them being the Stirling Exploration Company, Stirling Mining & Smelting Company, New Jersey Zinc Company of New York, Hayden & Stone Company of Boston, and The Eastern Mining & Milling Company. Up to 1924, the work was limited mainly to trenching, stripping, ? diamond drilling, and shot drilling.

Jan 1, 1937

By M. C. Bétournay

Under the requirement to define the economic advantages of using hydrogen fuel cell vehicles, a broad-scoped project was initiated to quantify the costs associated with operating fuel cell vehicles and diesel vehicles. While ventilation savings are clearly an advantage for the former, a complete and detailed analysis of this and other operational and capital cost elements was undertaken in order to provide the mining industry with factual information in considering the changeover from one technology to another. This paper outlines the results of the investigations to date defining the costs/benefits associated with capital purchases, operations (electrical/diesel, mine air heating fuel, ventilation, openings, surface and underground infrastructure, maintenance, labour, etc.), delivery of energy, regulatory obligations, and mine production. Considerations are given to the type and size of a mining operation, the depth, and location in North America. Significant ventilation power, equipment, and infrastructure savings are possible with the application of fuel cells for shallower mine applications. At depth, where heat is an issue, there is a reduction in benefit. Specific qualifiers such as minimum air velocities, dust dilution, shaft, and heating system velocity limits must be considered on an individual mine basis. While the capital cost for fuel cell mining equipment is currently higher than diesel versions, the high cost of fuel cells is anticipated to be reduced significantly in the near future with the intensification of manufacturing. In either case, the operational savings would probably be sufficient to balance the supplementary capitalization costs. Comprehensive reports have been issued.

May 1, 2005

By M. Veiga

"Mining is an energy and water intensive activity. Increasing energy efficiency and reducing water consumption are two of the key requirements in moving toward a more sustainable mining industry. Water reduction, reuse and recycle options are reviewed, identifying cases where these options have been implemented. Then a novel mine water network design method is described, which analyzes a mine/mill water system in order to identify areas where water requirements and water system energy requirements can be reduced. First, a site water balance is determined and major water consumers and sources are specified. Next, multiple possible combinations of supplying water to mine and mill consumers are compared. Finally, low energy and water combinations are identified.INTRODUCTIONMining consumes vast quantities of energy: The whole mining and metals sector consumes over 12% of the world’s energy (DOE, 2009). Mining also requires large quantities of water, although mining water consumption is a relatively small portion of the overall world water use. Even in relatively dry, mining-intensive countries like Australia and South Africa, mine water consumption is only 2-3% of national water demand (Brown, 2003). However, at the local level, when mining takes place in areas where water is scarce, mine water consumption can severely impact local supplies. In addition, acid rock drainage, leaks from waste impoundments, or direct disposal of tailing into waterways can contaminate surface and groundwater (MMSD, 2002). Mine water systems can be large energy consumers, but better mine water systems can reduce both water and energy consumption. Improving water system design and practice are key strategic requirements in moving toward a more sustainable mining industry.This paper addresses conventional base-metal or precious-metal mine sites, which consist of an underground or open pit mine and a mineral processing plant, or mill. Ore is extracted and processed through the plant to produce a saleable product. Tailing, or waste material, is then deposited in a tailing storage facility (TSF). Any rock removed from the mine with no economic value, or waste rock, is stored without being processed."

Jan 1, 2010

By A. G. Lylie

Introduction At the Britannia Mining and Smelting Company&apos;s mill, the equivalent of 2,500 to 2,800 pounds of copper sulphate crystals per day is made from copper which is precipitated from the mine-water. This copper sulphate is used in the mill for the recovery of sphalerite by2 flotation. From 1932 until 1936 it was produced by exposing the precipitate to air for thirty days and then dissolving the oxidized copper with dilute sulphuric acid. In 1936, the flotation of sphalerite was discontinued and, when it was resumed in 1947, steps were taken to try to improve the former method. The present paper outlines the way in which this was done, and describes the plant and procedure by which copper sulphate is now being made, and by means of which an appreciable saving is being effected. Aboratory Tests The previous work had established that the precipitate, which consists mainly of metallic copper, must be oxidized before the copper would dissolve in dilute sulphuric acid. Various methods for oxidizing it were tried but in the early laboratory work the only suitable one found was to heat the precipitate to 600°C. and hold it at this temperature for two hours. When this was done, approximately 90 per cent of the copper became soluble in .acid. This percentage was considered satisfactory for practical purposes, but the cost of roasting was prohibitive because only a small amount of roasted precipitate was required each day.

Jan 1, 1951

By Stopford Brunton

For many years it has been accepted as axiomatic that the greater number of &apos;veins&apos; or &apos;leads&apos; in the gold districts of Nova Scotia are of the &apos;interbedded&apos; type. The corollary to this hypothesis is that the vein or lead will have a continuous hanging-wall of one kind of rock, and a continuous footwall of the same or another kind of rock; but the essential point is that the foot and hanging walls are, according to this theory, both continuous and of uniform composition throughout; and that the vein or lead conforms to the bedding of the adjacent strata. With regard to the deposition of the gold in the rocks, the probability is that the key of the problem is contained in a statement by E. R. Faribault, of the Geological Survey of Canada: "The combined effect of cleavage, jointing, and stratification is to cause the rocks, especially the quartzites, to break into rhombohedral blocks". It is essential to comprehend that the rocks of the Province are no doubt folded into anticlines and synclines; but also it must be fully realized that the gold deposits and pay-shoots do not depend so much upon these as upon the fractures resulting from the disturbance caused by the intrusion of granite masses, and controlled by the combined effect of cleavage, jointing, and stratification. These fractures would form the channels through which the ore-bearing vapours and solutions would rise, and at the junctions of these fractures, where the fracturing was greatest, the easiest passages would be afforded to the ore carriers, with the result that the ore-shoots would be found at or near the intersections of fractures. It is a significant fact that in at least thirteen different districts throughout the Province, operators have at various times remarked upon the occurrence of rich ore at the intersection of &apos;leads,&apos; &apos;veins,&apos; &apos;beds,&apos; etc.

Jan 1, 1928

By C. W. Drury

It is practically fifteen years since stellite was first introduced into industry, and since then the progress made in its manufacture has been so rapid and the number of successful applications so varied that it was considered a review of the more important phases would be of general interest. Stellite is a cobalt-chromium-tungsten alloy, containing approximately 2. 75 per cent carbon. The high percentage of carbon is necessary for the requisite hardness and resistance to wear at ordinary temperatures, whereas the tungsten is essential to impart hardness at a red heat. Chromium imparts hardness and strength, and cobalt renders the alloys more resistant to oxidation. The metals cobalt and chromium are completely soluble in all proportions, both in the liquid and solid state, the equilibrium diagram showing a minimum in the solubility curve at approximately 50 per cent cobalt and l,340°C. Cobalt and tungsten are completely soluble up to 40 per cent tungsten, which is beyond the limit of the; tungsten content of stellite alloys. In the presence of carbon, carbides are formed, which are essential in stellite possessing good cutting or wearing properties.

Jan 1, 1930

By Damian Connelly

The metallurgical heart of the majority of copper oxide processes is the heap leaching operation. Fresh low grade sulfide ores is a far greater challenge.The success of this unit operation is so important that operators need to understand the ramifications of their decisions or non-decisions and how they could affect the downstream processing. Heap leaching is an operation that can be described as a scientific art whereby principles of science can be used to guide experienced personnel in attaining their goals. Recent advances have been made based on better understanding the ore characteristics. The success of a heap leach operation, or otherwise, is dependent upon a number of factors, notably: The type of ore to be treated The extent of testwork completed to define the process The interpretation of the testwork results Ore preparation prior to stacking Agglomeration and curing requirements Other issues are: Compliance with the ’smaller’ requirements of environmental authorities Adequate and timely drainage of solution from the base of a leaching lift The degree of saturation in the pads Heap porosity – coarser or finer ore, which is better? Higher or lower irrigation rates – which would produce a better result? Laying out irrigation pipework for ease of operation and maintenance The addition of water, raffinate during agglomeration where needed The heap leaching of sulfide ores, including chalcopyrite, via enhanced bacterial leaching is discussed. INTRODUCTION Over the last twenty years, production of extremely pure copper from solvent extraction and electrowinning (SX/EW) has become more common in a market of real declining prices for copper metal. This paper touches on a number of heap leach operations and experiences. These projects were subjected to extensive engineering design and resulted in low capital cost, efficient operations with a number of lessons learned. The key to these operations was the performance of the heaps and associated fluid collection systems rather than the plants themselves.

Jan 1, 2019

By Tim Hughes, Steve Gannon, Jennifer Abols

"In the past year, two very innovative gold ore processing plants have been designed, built and commissioned by Gekko Systems Pty Ltd. The first plant in Vietnam utilizes conventional crushing and ball milling followed by gravity concentration (Inline Pressure Jig (IPJ) and Falcon concentrator), flotation, intensive leaching (GFIL), the first industrial scale use of AuRIX®1001 ion exchange resin and a cyanide destruction circuit. The second plant, in Australia, uses a 3 stage crushing circuit to crush the gold ore to minus 1mm, followed by gravity concentration utilising a rougher, scavenger, cleaner circuit of IPJ’s and a Falcon concentrator. A direct smeltable gold concentrate is produced as well as a lower grade concentrate for future intensive leaching or sale. Both plants were designed and built within very tight time frames and budgetary constraints. The experience gained during the plants’ design, commissioning and operation are discussed.INTRODUCTIONGekko Systems (Gekko) is a leader in the development of innovative technology for gravity recovery and intensive cyanidation. It provides low cost and metallurgically optimal solutions for its customers. It has also led the trend away from whole ore cyanidation (CIP/CIL) towards gravity/intensive cyanidation (GIL) and gravity/flotation/intensive cyanidation (GFIL) plants. These types of plants offer low capital costs, low environmental impact and maximum return to investors (Rob J Longley et al, 2002). Key to this type of flowsheet is the application of a continuous concentrate unit, such as the InLine Pressure Jig (IPJ), which is designed to produce high gold gravity recoveries at a coarse grind (Sandy Gray, 2003). When combined with other gravity devices, and/or flotation, and intensive cyanidation, using the Gekko InLine Leach Reactor (ILR), very high overall recoveries can be achieved.In 2004, Gekko launched a new range of products called Gekko Modular Systems. The idea was to provide off the shelf, complete solutions for the separation and recovery of complex and free gold as well as the pre-concentration of diamonds. A series of modules were designed that incorporated Gekko manufactured as well as outsourced equipment. Gekko now offers modules ranging from feeding and conveying to crushing, gravity recovery, flotation, intensive cyanidation, refining and detox (see Figure 1)."

Jan 1, 2007

By J. Andrew Cornier, Mike Cooper

"Upon successful completion of the AG/SAG Mill project (Cooper et al., 2001) the Brunswick Mine concentrator was configured with single line processing through the AG/SAG mill, followed by two parallel ball mill and flotation circuits. The Stage Grinding project was undertaken to utilize a pre-flotation stage on the AG/SAG mill primary cyclone overflow and simplify the flowsheet by consolidating the two ball mill and flotation circuits, resulting in single line processing fi-om AG/SAG mill to final concentrate. Concurrently, the reclaim water supply capacity was increased to enable flotation cleaning at lower percent solids.Benefits from the Stage Grinding project include revenue enhancement from increased zinc grade and recovery combined with additional lead recovery. Further benefits included a reduction in the number of process pumps, reduction in loss associated with spillage to sumps and process simplification through efficient use of equipment layout.The Stage Grinding project was implemented in six phases over a period of seven months in 2000. Each phase was commissioned during scheduled concentrator shopdays with minimal additional downtime required. One year after project approval the Stage Grinding project was completed at a total cost of $1 1.8 million.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is one of the world’s largest leadzinc mines. Milling of ore began in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore fkom the No. 6 open pit located several kilometers away. In 1980 the pit was exhausted and the concentrator rationalized to accept a design feed rate of 10,500 tomes per day from the No. 12 mine. In excess of 100 million tomes have been milled to date, representing over three-quarters of the known reserve. The concentrator employs differential froth flotation to produce lead, zinc, copper and leauzinc bulk concentrates. The ore is massive sulphide, with approximately 20% valuable minerals, 60% pyrite and 20% silicates."

Jan 1, 2002

By E. C. Morton

The Western Australian School of Mines (WASM) has developed a facility for the static testing of large scale ground support elements. The samples are loaded using a mechanical screw feed jack. Instruments measure the displacement and the load being applied. Methods have been developed for testing of mesh, shotcrete and membranes. Mesh samples are restrained on all sides and loaded centrally. A new large scale punch test method has been developed to evaluate shotcrete and membranes. These products are sprayed on to a sandstone substrate containing a centrally located isolated disc. The sprayed product is loaded by displacing the disk. The different test methods are described in detail. The test program involved two types of mesh, several shotcrete mix designs with different curing times and one membrane product. The force-displacement responses are used to directly compare the products. The implications for implementation of the different ground support products are discussed.

May 1, 2009

By Olanrewaju A. Ojo, Xu Wang, Jian Xin Dong, Lina Zhang, Jerzy A. Szpunar

"The influence of crystallographic orientation on the pitting corrosion behavior of Ni-Fe-Cr alloy 028 was studied by a combination of X-ray diffraction (XRD), electron backscatter diffraction (EBSD), potentiodynamic polarization technique and atomic force microscopy (AFM). The results show that there is anisotropy of pitting corrosion that strongly depends on crystallographic orientation of surface planes. The distribution of pits frequency in standard stereographic triangle shows that the crystallographic planes close to {100} are more prone to pitting corrosion compared to planes of {110} and {111}. The calculation of surface energy (001) and (111) shows that the planes of high packing density of atoms have low surface energy with concomitant strong resistance to pitting corrosion. A correlation function between crystallographic orientation and pitting corrosion susceptibility suggests a method not only to predict the pitting resistance of a known textured materials, but also to improve corrosion resistance by controlling materials texture.INTRODUCTIONNickel-iron-chromium(Ni-Fe-Cr) alloys are widely used in various industries and engineering sectors due to their combination of good mechanical properties and high corrosion resistance(Hibner, 2001; Thomas, 2006; Ghosh, 2005).Ni-Fe-Cr alloy 028 (alloy 028)has such important characteristics worth mentioning. Alloy 028 contains high amounts of nickel, copper and molybdenum which improve its resistant to corrosion attack in reducing medium, and presence of high level of chromium makes it more resistant to oxidizing species. Moreover, alloy 028 is less expensive because of higher amount of iron compared to other similar alloys. Currently, alloy 028 is manufactured as evaporator tubes applied in the phosphoric acid production; production tubing and casing used in deep and sour gas wells; heat exchangers employed in nuclear power plants, and seawater-carrying piping and seawater-cooled heat exchangers (Bankiewicz, 2012; Kivisäkk, 2003; Gómez, 2003; Xian, 2012; Bellezze, 2004)"

Jan 1, 2017

By Mike Sapiro

"Heath Steele Mines is a base metal producer situated near Newcastle, N.B. presently treating 3500 TPD of complex Cu-Pb-Zn ore. The ore consists of massive fine grained sulfides averaging I. 1% Cu, 1.6% Pb and 4.5% Zn.The original mill started in 1956 at 750 TPD and was successively expanded through 1500 to 3000 TPD in 1969. In 1972 an expansion to 4000 TPD was initiated. It was planned to obtain the maximum benefit from equipment and manpower by adding some process equipment, instrumentation, an on stream analyser, and a process control system. The benefits from this approach could be greater than normally expected, because of the complex metallurgy of this ore.IntroductionThe crushing plant is of conventional design with two 5 ½ ft, Symons cone crushers with the crushed ore screened to -7/8 inch on a 61 x 16 1 Al I is Chalmers vibrating screen and stored in four 1000 Ion bins. There are two para I lei grinding circuits, each one consisting of the following: one Rod Mill in open circuit, one Ball Mill in closed circuit with two 20"" Krebs cyclones, and one Ball Mill in closed circuit with three 15"" Krebs cyclones, Al I the Mills are 9' x 121 Al I is Chalmers Mills. The secondary cyclone overflow from each grinding circuit is thickened and combined to form flotation feed. The final product is 65% - 400 Mesh. Two regrind mills have been installed as part of the expansion."

Jan 1, 1977