Search Documents

By A. J. Goodman

Introduction The position of Turner Valley in the foothills of Alberta, some thirty-five miles southwest of Calgary, is too well known to need further description. This attempt to interpret in detail the nature of the structure, and its relationship to neighbouring structures, together with general observations on the foothills belt, is based on work carried out in the office of the Supervisory Mining Engineer, at Calgary. The object in view was the correlation of the mass of evidence which had accumulated from the detailed examination of drill cuttings, and to discover, if possible, its structural significance. Unfortunately it is not possible to publish most of this detail owing to its confidential nature, and in consequence the reader is asked to accept certain statements, which under other circumstances would not be made without supporting evidence. The main argument for the general structural interpretation rests on evidence which has already been made public, and it is possible to proceed to logical conclusions on the main points. The evolution of ideas concerning the structure of Turner Valley is somewhat difficult to follow, as, compared with all that has been said on the subject, there is not a great deal on record.

Jan 1, 1930

By M. J. Slater

Ion exchange using resins is one of the few processes capable of reducing ionic contaminants in effluents to very low levels. Continuous fluidized-bed ion exchange is an advantageous technique for processing dirty effluents and thin slurries. It also reduces resin inventory and equipment cost compared to fixed packed beds. A simple continuous fluidized-bed unit has been investigated for treating effluents and its performance is described. Breakthrough curves were first obtained from static fluidized fixed beds; these data were then used to determine the required operating conditions for a periodic-flow, countercurrent fluidized-bed ion exchange system. A waste stream, containing about 56 ppm copper, was treated in the continuous system using an extraction fluidized bed depth of 203 cm and a flow rate of 1.22 cm3/ cm2s (900 gph / sq.ft) to yield an effluent containing less than 0.02 ppm copper. A generalized design method is proposed for similar chemical systems.

Jan 1, 1978

By A. Boehm

"For recycling LD slag into the steel making process, the phosphorous containing calcium silcate phases have to be removed from iron oxide phases. One possible technical solution could be magnetic separation in a wide range of susceptibilities from ferromagnetic to paramagnetic. To check the feasibility of magnetic separation the distribution of the magnetic susceptibility in size classes as well as the liberation of the phosphorous containing phase were evaluated by a new method combining two dimensional physical property analysis with QEMSCAN analysis. The particle size classes of energy controlled comminution products were subdivided into fractions of defined magnetic susceptibility using a hand magnet of well known field properties (pick up method). On the one hand the susceptibility classes were wet assayed on the other hand analyzed by QEMSCAN followed by data evaluation using iDiscover 5.3.1(FEI), which was adapted to the data structure of two physical properties (size and magnetic mass susceptibility). The results allow the comparison of mass based (3D) cumulative distribution of grades from the wet assays with the area based (2D) distribution from QEMSCAN analysis, in order to control a systematic (size dependent) stereological error for this special type of material. As the physical separation property forms a crucial parameter the results from the liberation analysis by QEMSCAN can be interpreted more profound with respect to an expectable separation result. Once the various mineral compositions of the particles are assigned to the physical properties the Henry Reinhardt chart serves to predict the best possible separation result and thus the feasibility of a separation technique.INTRODUCTIONThe two Austrian steel plants operated by voestalpine AG produce about 650,000 t (voestalpine 2014) of LD slag in the course of steel production from pig iron according to the basic oxygen process blowing oxygen in the converter by an oxygen lance. The process is also known as the Linz Donawitz (LD) steelmaking process. By the addition of lime (CaO), carbon, phosphorus, silica, manganese and sulfur, which are present in the molten pig iron, shall be oxidized and bound in the slag either as oxide or silicate phases, or leave the slag in the gaseous phase (CO). The average chemical composition of the investigated LD slag is given in table 1."

Jan 1, 2016

By Lloyd W. Trevoy

Syncrude Canada Limited is presently studying commercial production of heavy minerals from plant tailings of the openpit A lhabasca tar sands operation. When tar sands are processed and upgraded to synthetic crude oil, heavy minerals can be removed f rom the extraction circuit and beneficiated to provide concentrates of zircon and titanium minerals. Calculated recovery rates indicate that crude oil production capabilities of 105,000 barrels per day would provide 26,000 tonnes of zircon and 114,000 tonnes of titanium minerals annually. The titanium minerals concentrate is a mixture of ilmenite, leucoxene and rutile; it could be used as recovered or upgraded to synthetic rutile. With the consrruction of further synthetic crude oil plants in Western Canada, a large reserve of heavy minerals will become available.

Jan 1, 1984

By M. van de Vijfeijken

This paper will first give a short overview of the Copper Mountain project in British Columbia, which just has started commercial operation earlier this year. The grinding process with one 34' x 20' SAG mill and two 24' x 39.5' ball mills will be briefly discussed. All three mills are gear driven by a ring gear, dual pinion and two low speed synchronous motors. Copper Mountain has installed on all three mills, the new state-of-the art dual pinion mill drives. All the inherent operation and maintenance features of this drive technology will be discussed, as well as the advantage of having variable speed control also on the ball mills. The installation and commissioning of the mills and drives at Copper Mountain will be briefly reviewed. Finally the first field measurements on these low speed mill drives will be presented, with the main focus on the low mechanical stress impact of these mill drives on the pinion and ring gear, as well as the accuracy of the load sharing between the two motors.

Jan 1, 2012

Several inorganic reagents and organic polymers were tested as depressants in the single mineral flotation of ultrafine iron oxide and hydroxylapatite with Dowfroth 250 as a frother. It was observed that the inorganic reagents and the low molecular weight polymers generally caused dispersion of the ultrafine particles, and consequently their recovery into froth products more or less equaled the recovery of water. On the other hand, the high molecular weight polymers caused different degrees of flocculation of the ultrafine particles, and their recoveries were much lower than the recovery of water. These observations pointed to a need to re-define flotation depressants in fine particle flotation. The traditional definition of a flotation depressant, i.e., to make particle surfaces hydrophilic by forming a hydrophilic film and/or by removing collector and activator coatings, is sufficient for relatively coarse particles. However, to prevent fine and ultrafine particles from floating, a successful depressant should not only make the particles hydrophilic, but also enlarge the particle sizes so that they do not enter the froth product by mechanical entrainment. Polymeric depressants are ideal for these purposes. The different schemes to use polymeric depressants in the selective flotation of fine and ultrafine particles were discussed These schemes involve the integration of the polymeric depressants into other size enlargement processes such as shear flocculation, oil agglomeration, etc., for hydrophobic particles.

Jan 1, 2004

By C. B. Webber, W. A. Grell

"Sherritt Gordon's Ruttan Mine is a copper-zinc operation located approximately 600 miles north-west of Winnipeg. Open pit mining began in 1973 at 10,000 Tpd., with a change over to underground mining in 1981 producing 7,500 Tpd. Ore is crushed to -3/4"" followed by rod and ball mill grinding (two ball mills in series), differential copper-zinc flotation, and dewatering. The copper and zinc concentrates are trucked 75 miles to Lynn Lake, where they are shipped by rail to the HBM&S smelter at Flin Flon.This paper describes a method used to predict the effect of grind particle size on metallurgical performance, as well as details on the copper and zinc metallurgical performance due to fine grinding in actual plant operation.Initial statistical studies on historical data (including ore source, head gr3de, grind, etc.) indicated that copper and zinc recoveries increased with fineness of grind, in the range of 50 to 65% -200 mesh.In order to extrapolate beyond 65% -200 mesh, and to develop expected nonlinear relations between grind, Cu concentrate grade, and recovery, the assays of screen fractions of copper concentrate and tailing were used to determin8 the relation between net smelter return (a function of grade and recovery) and grinding cost. The optimum economic grind would be that grind at which the net smelter return less grinding cost reached a maximum."

Jan 1, 1982

By A. R. Miller, M. C. Bétournay, D. L. Barnes

"A number of successful proof-of-concept projects have been carried out to replace conventional power application, such as diesel and rechargeable batteries, in underground mine vehicles. This has led to the development and testing of the world’s first fuel cell production vehicle, a mine locomotive. A fuel cell loader is being built and tested.This paper provides an insight into other projects that are being carried out. Some are related to further underground applications, and some to further research, such as refueling options, power plant durability, and vehicle automation.Also outlined is an evaluation of the overall mining applications and advantages this technology can bring to underground mining, including the facilitation of automation and tele-remote operation."

Jan 1, 2003

By B. M. Coombes

The McCracken and Stacey (1989) method of assessing geotechnical risk for largediameter raisebored shafts has been the basis for most Australian pre-construction raisebore investigations for the past 20 years. At the time of its publication, the McCracken and Stacey (M&S) Method did not include a database of raisebore diameter and rock mass conditions versus actual performance. It did, however, provide a chart that quantified geotechnical risk in terms of proposed shaft diameter and the raisebore rock quality index, QR. Two parameters, RQD/Jn and Jr/Ja were identified as being critical to raisebore stability, but the contribution of these to overall raisebore stability was not quantified. Peck and Lee (2008) published a database of raisebore performance from Australian case histories. Raisebore diameter and ground conditions, in terms of a Lower Bound QR value, were presented for 50 cases versus raisebore performance. This paper updates the database with further case histories and corrected SRF values. This paper further evaluates the reasons for the variable raisebore performance for similar RSR values. For all case histories, three parameters, RQD/Jn, Jr/Ja and Jw/SRF are investigated to assess their influence on raisebore performance.

May 1, 2011

By J. C. Keenan

Company-community agreements are widely considered to be a practical mechanism for recognising the rights, needs and priorities of peoples impacted by mining, for managing impacts and ensuring that miningderived benefits are shared. The use and application of company?community agreements is increasing globally. Notwithstanding the utility of agreements, the gender dimensions of agreement processes in mining have rarely been studied. Prior research on women and mining, however, does show that women are often more adversely impacted by mining than men, and face greater challenges in accessing development opportunities that mining can bring, however there is currently little to no guidance for companies, government or communities in terms of bringing a gender perspective to the fore in mining and agreement processes. While it is undisputed in human development literature that investment in women and sensitivity to gender delivers long-term health, education and local development outcomes, a number of key factors remain unexplored in debates about mining and development. These include: women?s participation in agreement processes, the gendered distribution of agreement benefits, and the extent to which impacts and benefits influence (either positively or negatively) women?s development and economic inclusion. This paper presents the results of an applied research project undertaken by the Centre for Social Responsibility in Mining (CSRM) at The University of Queensland and funded by a partnership between the Minerals Council of Australia (MCA) and the Australian Agency for International Development (AusAID). The project sought to connect with practitioners who had been directly involved in agreement processes to hear grounded perspectives on the interaction of gender dynamics and agreements, and connect those experiences with the broader literature. Findings from this study have implications for the role of companies and governments in promoting gender equality and empowerment as part of their commitments to sustainable development. A key challenge for companies will be navigating the territory of cultural norms and gender equality. The authors argue that without consideration of the gender perspective, and appropriate responses, mining agreements may not be inclusive or representative and may exacerbate gender inequalities and fail to contribute to long-term sustainable development.

Aug 1, 2013

By D. K. Matlock, D. J. Hamre, J. G. Speer

Ultrafine ferrite (UFF) grains may be produced in surface layers of plate steels using controlled intermediate cooling followed by deformation. Experiments were conducted using a 0.12 C - 1.26 Mn steel on a Gleeble 1500 hot deformation simulator. Taguchi designed experiments were used to evaluate prior austenite grain size, intermediate cooling rate, intermediate cooling temperature, intermediate hold time and amount of reduction in order to observe the effects of variables and their interactions on the final microstructure while minimizing the number of required test runs. Evaluation of resulting microstructures and mechanical properties revealed a preferred thermal and mechanical history for developing ultrafine microstructures in surface layers of plate steels. Application of the fundamental concepts of phase transformations to industrial plate rolling is considered.

Jan 1, 2004

By T. Patching

"A GLANCE BACK AT what has happened in the past is often a useful guide to the future, although it should be used mainly to provide a sense of direction rather than a map that must be followed. As a preamble to discussing some of the questions posed by the organizing committee it may be appropriate to briefly review the distribution and careers of the graduates of our Department since the first degree in mining engineering was awarded in 1916. An attempt has been made to keep a record of the locations and careers of the Department's 540 graduates in mining and metallurgical engineering. Almost all of those who graduated before 1930 have now retired, but a very large proportion held positions as senior executives prior to retirement. A major proportion of those who graduated before 1950 are now in what might be considered senior management positions. Those who have 10 to 20 years of experience are generally in work of senior engineering responsibility or in supervisory or junior management ranks, while those who graduated in the last ten years appear to be generally in staff engineering or junior supervisory positions. This classification is admittedly imprecise because it is difficult to determine from a job description whether duties should be considered of an engineering or management nature - a distinction between the two terms is often over-emphasized. Nevertheless, the trend from technical engineering to management responsibilities with seniority and years of experience is clear in the careers that we have been able to follow."

Jan 1, 1972

By Reno Pressacco

Abstract- Agrium Inc. is a world leader in the production, distribution, and marketing of agricultural products and services in both North America and Argentina. The new phosphate mine and mill complex located southwest of Kapuskasing, Ontario, was constructed to replace an offshore supply of phosphate rock, and produces a high-grade phosphate concentrate. The Cargill Township Carbonatite Complex is one of a series of carbonatite complexes in the region that are hosted by the 1.9 Ga aged Kapuskasing Structural Zone. The carbonatites in the mine area have intruded Archean gneissic granodiorite rocks of the Wawa Subprovince, and metasedimentary rocks of the Quetico Subprovince. The Cargill Carbonatite Complex displays a typical concentric zonation pattern from an outer ring of alkalic pyroxenites, through an inner ring of sövite-carbonatite, to a central core of rauhaugite-carbonatite. The initial carbonatite intrusion and subsequent residual orebody have been modified by faulting such that the northwestern third of the complex has been displaced approximately 2.5 km northeast. The phosphate ores are composed principally of residual apatite sands that were formed by the weathering and dissolution of the soluble minerals of the carbonatite protolith. These ores are subdivided by their iron content into high grade (A ores) and lower grade (B1 and B2) ores. They are separated from the primary unweathered carbonatite by a layer of saprolite, whose thickness varies depending upon the composition of the underlying carbonatite. Cretaceous waste materials consisting of well-sorted silica/kaolinite sand and peat deposits are typically found to stratigraphically overlie the ores. A minor amount of the ore feed comes from cemented phosphate ores. All rock types are covered by Pleistocene glacial tills and clays.

Jan 1, 2001

By M. Drozd, M. Somppi, Z. Yamak

"Granular activated carbon is widely used in the gold mining industry for gold extraction from aurocyanide-containing slurry. The extraction process can employ carbon as part of the gold recovery operation for various circuit designs including carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) circuits. However, various qualities of activated carbon exist and the durability of the material can change significantly from source to source. Handling this expensive reagent can pose challenges when fine carbon losses occur in the CIP, CIC, and CIL circuits. Additionally, any gold that is adsorbed to these carbon fines can also be lost by various mechanisms including carbon attrition and fracturing, inefficient coarse-fine separation, and poor carbon fines capture. With the above in mind, a series of tests were conducted to investigate standardizing simple laboratory methods for testing carbon quality. A standard procedure beyond or enhancing ASTM methods can serve as additional starting points for evaluating carbon specific to the gold industry. The investigation focused on size distribution, flatness, wet attrition resistance, surface area, gold kinetics, and gold loading. The final results provided information to generate an equation for ranking carbon samples to plant performance.IntroductionActivated carbon for use in gold extraction is amongst the most commonly found processes in modern gold-milling plants. Although gold losses are inevitable in the milling process, operators often focus on the importance of maximizing gold recovery. One focus area that is important in gold recovery is optimizing the use of activated carbon and examining potential changes to realize improved economics for carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) processes."

Jan 1, 2017

ABSTRACT The inevitable uncertainty in modelling spatial variables decreases as more data become available. This reduction depends on the properties of the variable being modelled. Spatially continuous variables show less uncertainty for a given spacing than erratic variables. A geostatistical simulation based approach is developed to quantify the relationship between uncertainty and data spacing. Reference realizations are sampled to condition additional realizations and quantify uncertainty. The procedure is automated, making it straightforward to consider sensitivity and different geological domains. A case study of the relationship between uncertainty and data spacing for net oil sands thickness data from northern Alberta is presented. _ KEYWORDS Simulation, Sampling,

Jan 1, 2013

By R. E. Barbosa

Seepage forces generated during tunnel excavation affect the ground response and may cause severe instability problems, including total ground collapse and flooding into the tunnel. This paper presents a new closed-form analytical solution, for stresses and displacements around a cylindrical tunnel excavated in a porous water-bearing elasto-plastic material, which includes the effects of seepage forces. The analysis is carried out in terms of effective stresses and pore water pressures. The solution shows that seepage forces may have a major effect on the effective stresses around the tunnel, on the extent of the plastic zone, on the radial displacements, and on the tunnel support requirements. The conditions for development of a ?flowing ground? condition at the tunnel face have been identified. The paper presents a procedure for the hydromechanical ground-support interaction analysis, to determine the excavation induced inflow and the pressures acting on the lining, throughout the progressive driving of the tunnel, including the effective pressures exerted by the ground and the pressures generated by the water.

May 1, 2009

By Jaime Meléndez Martínez

Recent interest in unconventional reservoirs motivates our work in laboratory measurements of seismic anisotropy. Seismic anisotropy is the variation in speed of a wave as a function of its direction of propagation. Analyzing anisotropy in unconventional reservoirs is important since anisotropy leads, for example, to differential stresses upon loading and could affect hydraulic stimulation (Reinicke et al., 2010, Zimmermann and Reinicke, 2009); in this sense, laboratory measurements are an important tool to study seismic anisotropy at small scales which can aid in the characterization of larger formations. The purpose of this work is to describe the laboratory methodology used to simultaneously measure ultrasonic P and S-waves in three different directions from a single core sample. Elastic anisotropy of a Proterozoic sedimentary rock from south-west Alberta is investigated. In metamorphic rocks seismic anisotropy is caused by preferred mineralogical alignment or foliation. Assuming a transversally isotropic medium, arrays of compressional and shear piezoelectric ceramic transducers were mounted on a sample trimmed from a core to measure travel times of ultrasonic P-waves and S-waves as a function of confining pressure at directions perpendicular, parallel, and oblique to the plane of foliation (bedding). Results show strong anisotropy agreeing with the assumption of a transversely isotropic medium. Dependence of travel times and hysteresis effects can be observed when pressurizing and depressurizing.

Jun 1, 2012

By A. A. Tytko, T. S. Golosinski

"The paper discusses the accuracy of magnetic inspections of corroded hoist ropes. It quantifies the error of measured LMA (loss of metallic area) caused by presence in the rope of ferromagnetic products of corrosion. The paper concludes that in mining practice this error is not significant. Hoist Rope Corrosion and its AssessmentCorrosion is one of the most common forms of wire rope wear. For ropes working in wet mine shafts, ropes used by the fishing industry and, in general, ropes working in humid and chemically active environments, corrosion wear is usually the prime reason for rope discard. In most mining applications, rope corrosion is accompanied by fatigue cracking of wires, abrasion of external wires, internal nicking and other forms of wear.Quantification of corrosion damage in ropes using standard inspection procedures and examination methods is very difficult. Qualitative comparisons are sometimes used to describe the degree of rope corrosion to compensate for the lack of quantitative measures (SABS 0293, 1996). If available, the results of magnetic examinations of ropes may be of help in assessing their corrosion weakening.Magnetic rope examination requires that the rope first be magnetized. After that, the rope magnetic flux and the leakage flux along the rope are measured. The first is assumed to be directly proportional to rope metallic area (LMA) and its changes are indicative of the rope’s loss of breaking strength (LBS). Existence of the second indicates existence of local faults (LF) in the inspected rope. As the corrosion of rope results in development of corrosion cracks and in loss of rope metallic area, both the LF and the LMA should be used to quantify the level of rope corrosion. More specifically, the changes to the amplitude of the LF signal are considered to provide qualitative information on rope corrosion (Hansel et al., 1990), while those of the LMA signal are believed to provide quantitative information (Geller and Rousseau, 1990; Golosinski, 1996)."

Jan 1, 1999

By H. Bouzahzah

Sulfidic tailings, subjected to atmospheric water and oxygen action, can generate acid mine drainage (AMD); which is the most important environmental problem facing the mining industry. AMD generating potential can be assessed by the static tests which consist of a screening method where the neutralization potential (NP) and the acid-generating potential (AP) of a given rock sample are determined. The AP and NP are determined separately in the different static test existing procedures which can be divided into two distinct classes: chemical and the mineralogical methods. For some chemical method, the AP is calculated on the basis of total sulfide sulfur content in the sample which may overestimate its AP if significant quantities of non-sulfide sulfur species are present (e.g. organic S in coals, some sulfate as gypsum, barite, etc.). However, the mineralogical method evaluates the AP by the sum of the individual sulfides participation on acid generation based on their concentration within the sample and can be more accurate than the chemical method. For AP calculation, the Paktunc (1999a) mineralogical static test takes into consideration all sulfide minerals occurring in the sample. However, it does not take into account the rates of acidity production of these sulfides submitted to weathering conditions. So, the present study focusses on the modification of Paktunc AP calculation by considering the acidity production rates of these minerals. To reach this objective, five base-metal sulfides (pyrite as reference, chalcopyrite, sphalerite, arsenopyrite, galena), diluted within quartz (25?75 wt.%) simulating mill tailings were subjected to a kinetic test to evaluate their AP. The results show that all the studied sulfides minerals generate acidity at different rates, so the Paktunc?s equation for AP calculation has been adapted accordingly.

Aug 1, 2013

By B. K. Gorain, A. W. Stradling

"The traditional metallurgical scale-up techniques for flotation plants are based on lumped flotation rate constants, dimensionless hydrodynamic numbers and the use of safety factors. Once the plant has been designed, the flotation principles that govern scale-up play almost no role in the optimization of the circuit to meet its metallurgical targets. This deficiency can potentially lead to a plant design incapable of meeting its targets, especially when circuits incorporate large flotation cells. This paper demonstrates the application of the k = PSbRf model in providing a suitable framework for flotation modelling, scale-up and circuit optimization, thus presenting an integrated approach to the problem. Studies were conducted at Teck Cominco’s Red Dog concentrator to characterize cell hydrodynamics, gas dispersion properties, froth flow behaviour, entrainment and ore floatability to obtain the key data necessary to develop a model for the flotation circuit. The findings of these studies are presented in this paper, which provide valuable insights into the modelling and optimization of the Red Dog flotation circuit. IntroductionThe traditional methodology for flotation scale-up and plant design is based on the ruleof- thumb with safety factors and dimensionless hydrodynamic group similitude considerations. With the recent trend toward larger flotation cells with volumes of 150 m3 and greater in concentrators, the problem of scale-up has become even more acute. The scale-up factors that may have been tolerated on smaller cells are not applicable to larger cells. The transportation of froth in these large cells adds further complexity to the problem. Arbiter et al. (1980) foresaw this problem and pointed out that if scale-up were attempted by rule-ofthumb and trial-and-error, the probability of failure would then increase with scale. This problem is confounded by the fact that the design and scale-up considerations used for a new flotation circuit play almost no role in optimization of the circuit to meet its metallurgical target. This results in a plant design, which may be incapable of meeting its metallurgical targets. There have been several instances where new concentrators have required significant circuit modifications and additional capacity to achieve design targets."

Jan 1, 2003