Search Documents

By George Delorme

"AbstractThe basic intention of this paper is to present, from a practical viewpoint, a thorough outline of all the sound and accepted principles connected with attaining satisfactory rope performance from multi-rope friction winders.In order to emphasize the importance of some aspects of rope maintenance, a limited amount of hoist rope theory has been included, a s it is felt that without this, some of the more critical, but nevertheless practical, aspects would perhaps pass without full appreciation of their individual merit.It is very much appreciated that many of the maintenance topics and practices discussed herein are already being observed with a high degree of skill among those already involved in modern friction winding. The hope is expressed, however, that the paper will be of additional assistance, and of particular help in introducing sound maintenance principles to those who are moving into this field of operation for the first time.Hoist RopesWITH a multi-rope friction winder system, structural upset within the hoist rope's cross section can occur if the ropes slip in the drum treads. This upset will usually appear at either end of the rope at the tangent point of the drum or deflection sheave with the respective conveyance in the normal uppermost position. This slipping action on the drum causes the outer cover of a Full Locked Coil or the strands of a stranded rope to shift, leading to structural upset. The result very often means that the ropes have to be withdrawn from service before completing their maximum service potential.The cause of any rope slipping in its tread can be associated with a discrepancy in tension of that rope between one side of the drum and the other."

Jan 1, 1977

By Yang Shuxin, Guo Qiliang, He Ping, Lu Lizhi, Yao Rui

"We combined stepwise regression and constrained regression statistical method to obtain the best boundary conditions for the calculation of in-situ stress field in Wushaoling tunnel using finite element method. Our numerical results reveal that: the main geologic factors contributing to the initial background stress are gravity and tectonics; the principal stress values would drop in fault zones; the angle between the maximal horizontal stress and the axis of Wushaoling tunnel is acute; Wushaoling tunnel tends to become stable when this tunnel has 2:1 ratio of the height to its width; the possibility of rock-burst exists under high stress.INTRODUCTIONStress state of engineering region is an important factor affecting the stability of project. Geological disasters in the project area are closely related to their stress environment. Wushaoling tunnel which is 20,050 meters long, lying along Lanzhou-Wuwei segment of Lan-Xin Railway in China, is the key project of Lan-Wu double-track railway. The region surrounding this tunnel is under a high stress environment. Accurate identification of the stress environment of the engineering area and the interaction between geomaterials and geotechnical engineering construction holds significant scientific and practical value for engineering design, construction, and operation.Many scholars explored and discussed the present-day tectonic stress through investigations of tectonic evolution history (Ding, & Lu, 1986), crustal deformation (Zoback, 1992), focal mechanisms (Yang et al., 2003, Xie, Cui, & Zhao, 2004), and so forth. However, the above methods would only provide the approximate direction of the principal stress in a broad region, and could not give the absolute stress values. In-situ stress measurement is one of the primary means to directly gauge the current crustal stress. However, in-situ stress measurement can only be applied in small number limited by measurement conditions."

Jan 1, 2015

By Doug Smith, Gary Taylor, Paul Ogryzlo

"Uranium mining and processing typically requires large quantities of high-grade reactive quicklime for the neutralization and clean-up of contaminated mine water and mill process waste streams. Currently the Saskatchewan uranium industry’s lime requirements are being supplied from deposits located in Manitoba and Alberta, resulting in transportation costs, which equal or exceed the market value of the product. During the summer of 2001, the northern village of Pinehouse located 220 kilometers south of the Key Lake uranium mill, staked two previously discovered limestone deposits. The relatively shallow deposits, known as Missi Island and Sleeping Giant are located in close proximity to one another, approximately 35 km south of Pinehouse adjacent to highway 914. This paper describes the results of a scoping study carried out by AMEC for the development of the two deposits based on a seasonal limestone mine and a continuous 40,000 to 60,000 tpy wood fired calcining plant designed to supply all of the quicklime needs of the Saskatchewan based uranium industry. Also described are the results of calcining and customer acceptance testwork on samples of lime prepared from recent Pinehouse limestone drill core. The potential benefits of the project include a significant new source of revenue for the community of Pinehouse, lower lime costs for the Saskatchewan uranium industry and employment for northerners in the mining, processing and wood harvesting operations.IntroductionInterest in the Pinehouse/Massinahigan River area for limestone was precipitated by the results of a 1977 industrial minerals drill hole program by the Saskatchewan Department of Mineral Resources. These results led to the acquisition of land in the area by Missi Island Mines Ltd who carried out extensive exploration during the period 1978-1982. They discovered a deposit on the southwest side of the Massinihigan River thought to contain approximately seven million tonnes of limestone with an average grade of 94.5% CaCO3. Missi Island carried out preliminary feasibility studies and prepared an Environmental Overview Statement. However, in spite of positive recommendations, the project was dropped in the mid 1980’s."

Jan 1, 2003

By B. N. Church, J. J. Barakso, A. F. Bowman

"An evaluation of mineralization in the Goosly- Owen Lake area of central British Columbia is the result of a comprehensive geochemical study of rock samples obtained from a regional geological survey. The dispersion of metals in country rocks about a line of Tertiary intrusions suggests that these igneous bodies may be genetically related to known sulphide replacements, disseminations and vein deposits. The geochemical investigation is based on the determination of 12 elements from samples gathered from more than 800 scattered field stations. To assist processing and interpretation, the data are subjected to a variety of statistical procedures, including correlation of the elements, factor analysis, clustm• analysis and computer contouring of the elements. Some practical applications of rock geochemistry in regional exploration are indicated."

Jan 1, 1976

By L. D. Smith

"Those who submit competing proposals for projects seek to present senior management with complete and fully supported material that will not fail under questioning. Hopefully, misleading notions and omissions will have been minimized and there will have been testing of the assumptions regarding the economic, social and political environments. A capital project evaluation team can do management and itself a service by including a sound approach to the impact of inflation (and its twin problem, interest) on a project and a great disservice with an inappropriate approach to inflation.InflationHandled deftly, inflation can alter a project evaluation to show almost any result the handler desires. It must be a constant source of frustration for design people and cost estimators to spend weeks perfecting the technical aspects of a project in order to minimize costs, only to have all of their efforts set awash in a sea of financial and economic assumptions that submerge all of the detail. In all of this, inflation is perhaps the largest offender, with inflation criteria often being brought to bear at the last minute, almost as an afterthought. Perhaps this tardiness reflects the difficulty of the subject and the belief that senior management will take its own approach to the problems of inflation. Such a belief is unfair to senior management, for it is entitled to not being misled by omission. It is entitled to the full use of the skills of the evaluating team, including respectable assumptions of the impact of inflation.Working in a consulting context, one has the opportunity to participate in the evaluation of a large number of projects. Reflecting the observation of a wide range of views regarding the subject of inflation, this paper will-address the impact of five different approaches to inflation on the evaluation of a single Canadian mining project."

Jan 1, 1987

By E. Fritz

This paper reviews the history, developments and 10 milestones of the oxygen steelmaking processes, with a special focus on conventional autothermic converters, high-speed converters with a blowing rate up to 5 m3n/t min and allothermic converters with coal addition, post combustion and the possibility to increase the scrap rate up to 50%. Related operating results are introduced. A new process route, which is based on hot metal and chromium ore, is outlined. The cost advantage for the production of 304 stainless steel grade is higher than 100 USS/t. The synthesis of EAF and oxygen converter steelmaking, a comparison of decarburization rates, refining combustion burners for optimized oxygen-management in EAF and an example for a large advanced EAF are outlined. Possibilities of flexible steelmaking and the growth and outlook of worldwide oxygen steelmaking are described.

Jan 1, 2004

By Mafalda Arias

Most mining and mineral exploration companies? operate in remote locations, in Canada or internationally. Not knowing the cultural imprint of your team and the places where your company is active, may lead to problems. To set the foundation for a better world, it?s important to built trust and relationships inside your global team, within communities and together with stakeholders. Building the ?invisible asset? and developing intercultural awareness is an important part of leadership programs for geologists and engineers on your team, and should be a key component of your Corporate Social Responsibility initiatives. Why is culture important for mining and mineral corporations in their CSR initiatives? Because culture is the foundation of your organizational identity. Understanding the impact of identity, for an organization and for each individual, will provide a description of the experiences and values that affect every work placed interaction, with your clients, with colleagues, with suppliers, with the community of the host country. Each one of us sees and evaluates the world through our perceptions. Through these perceptions we give meaning; how we view and understand our reality which sets the tone for how relationships are built. This is what I call building the ?invisible asset?. Identity, experiences, values and beliefs are invisible commodities, locating them can be as difficult as finding a mine. But if they are not located, the commodity does not have value. Just like in the work we do in our industry. For example when you are working in an underground gold mine and the vein is lost, you keep on working and trying to find the vein; time passes, money is being used and no results. You decide to bring an expert on this type of deposits who gave you directions that allowed you to find the vein. To be a responsible citizen of the world and to set the foundation for a better world, it is imperative to go deep, as deep as your next drilling program, because only there and then, can you develop the cultural sensitivity and the ability to become an agent of change for responsible, sustainable and profitable businesses.

Oct 1, 2010

By Guy Chevalier, Jean-Guy Chartrand, Louis Barrette, Daniel Michaud, Michel Fortin

"COREM has developed, specifically for the mineral industry, a mobile laboratory using the Laser-Induced Breakdown Spectroscopy (LIBS) technique. It has been used to perform onstream analysis (OSA) of the chemical composition of slurries in both gold-ore and iron-ore processing plants. Industrial tests have been carried out respectively at La Mine Doyon (Cambior), a gold-ore processing plant near Rouyn-Noranda, Quebec, and at QCM's iron-ore pelletizing plant in Port-Cartier, Quebec. The aim was to demonstrate that the LIBS technique is capable of providing information that meets the needs for process control. C, Si, Ca, Mg, Mn and Al were the elements targeted on iron ore while Cu, Fe, Ag and Au were targeted for gold ore. The results obtained meet or exceed the requirements for process control and consequently clearly show that the LIBS technique is suitable for industrial applications.The feasibility of OSA, through in-plant validations using COREM’s LIBS mobile laboratory, has been demonstrated in four essential aspects: slurry sampling, LIBS chemical measurement, robustness for continuous operation, and functionality for industrial operators.INTRODUCTIONThere is a general need for optimization in the mineral industry. Process control is a favoured means to achieve this goal (McKee 1991). Real-time knowledge of process status is the key to effective control (Da Silva 1994). Only a few techniques, such as XRF, NMR and digital imaging, are currently amenable to chemically monitor industrial processes (Braden 2002). LIBS is an emerging technique with appealing characteristics for on-line and real-time measurement of bulk material (Lorenzen 1992, Palanco 2000). While our ultimate goal is to provide our industrial partners with performing monitoring tools, a shorter-viewed objective is to demonstrate the feasibility of developing a LIBS system for OSA. The LIBS technique has shown interesting capabilities for measuring solids, liquids, dusts and gases. Our work has focused on mineral slurries (Barrette 1999 and 2001, Turmel 1999). Special equipment is needed to perform in-plant validations. A mobile laboratory based on the LIBS technology has been assembled for this task."

Jan 1, 2004

By Raj Rajamani

In general, many past works examine mill load, mill power, shell lifter design etc with a view to improving the mill capacity. On the contrary, only a handful of papers have addressed the transport of fine slurry through the pulp lifters. We present the flow dynamics of pulp lifters via laboratory scale experiments, high speed photography and modeling with computational fluid dynamics. Next, the flow behaviour in ArcelorMittal?s Mont-Wright autogenous mill discharge flow is examined. In an effort to improve mill throughput, a comprehensive simulation and plant scale study of the mill was taken up with a focus on the shell and pulp lifter design. The shell lifter was found to be at its optimum limit for breakage of ore particles given the constraints of wear life and occupied volume. Next, the pulp lifter study was taken up with computational fluid flow code and discrete element code. The simulations directly showed that there was considerable carry-over of slurry. This effect was traced to the area restriction in the pulp lifter channels. Further, crash-stop studies confirmed slurry pooling within the mill. Thus it was readily apparent that mill throughput can be increased if the pulp-lifter could be redesigned. Consequently, the discharger section of the pulp-lifter was redesigned. First, this paper outlines the modeling in laboratory scale studies and plant scale studies leading up to the discharger design. Next, the discharge flow in seven different published mill surveys is predicted with computational fluid dynamics (CFD) methodology shown here. Finally, Mont-Wright mill circuit performance before and after the discharger redesign is described. The usefulness of fluid flow simulations in the design of pulp-lifters is emphasized.

Jan 1, 2012

By Jodi Roberts, Curtis Deredin, Jean-Guy Paulin

"Since the establishment of the Six Sigma quality improvement program in 2001, several projects have been successfully carried out in the copper-lead, zinc, copper separation, lead upgrading and bulk flotation circuits in the Brunswick Concentrator.This paper provides an update on the process improvement initiatives that have taken place since 2004 using the Six Sigma methodology:•,The recirculation of warm water to the flotation circuit (to save on energy costs)•,Installation of a heat recovery tower to recuperate the heat lost from the zinc dryers•,Installation of an extra row of cleaner-scavenger cells for the copper-lead circuit for extra capacity, and a new reagent scheme for the copper separation circuit that have increased copper and lead recoveries.INTRODUCTIONThe Brunswick Mine Concentrator (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The concentrator utilizes selective flotation to produce zinc, lead, copper, and bulk lead/zinc concentrates. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.Figures 1, 2, and 3 illustrate the historical annual average metallurgical performance and process improvements achieved at Brunswick Mine for the zinc, lead and copper concentrate products. The objective is to continuously direct metallurgical performance towards increasing grades and recoveries while minimizing operating costs."

Jan 1, 2008

By J. E. Nesset, J. A. Finch, Rosenblum. F., S. Somot

"In a previous presentation at the CMP, evidence was shown for the formation of hydrogen sulphide (H2S) in self-heating experiments on pyrrhotite-rich samples (Somot and Finch, 2006). Oxidation of H2S is strongly exothermic leading to the proposition that H2S is playing a key role in the self-heating process. Subsequently, tests in two weathering apparatus (I and II) were run under varying oxygen levels to further examine conditions leading to self-heating. To characterise their resulting self-heating capacity the samples from the weathering tests were subjected to a modified Stage B test using the self-heating apparatus developed by Rosenblum and co-workers (Rosenblum and Spira, 1995; Rosenblum et al., 2001). Results showed highest self-heating after weathering occurs under low oxygen conditions, supporting the H2S hypothesis. It was observed that highest heating rates are not directly related to highest weight gains of samples.INTRODUCTION“Sulphides” refer to several types of minerals containing sulphur in its lowest oxidation state of - 2. Self-heating is the spontaneous heating of a material without external heat input. It is well established that some sulphides will self-heat on exposure to moisture and oxygen (Farnsworth, 1977; Good, 1977; Rosenblum et al., 2001; Wu and Li, 2005). This process is highly exothermic and if the heat generated is not dissipated, combustion may occur when the temperature reaches the ignition point of the sulphide (typically 350-400 °C). The hazards of sulphide self-heating range from handling hot material, to sulphur dioxide release, to fires. The literature documents self-heating incidents underground, on ships and trucks transporting sulphide concentrates, and in mine waste (tailing) disposal areas (Stachulak, 1990; Lukaszewski, 1969; Headley et al., 1977). Lukaszewski (1969), Farnsworth (1977), and Good (1977) note that sulphide minerals can act as fuel to promote underground mine fires. Based on such findings, sulphide minerals could become classified as hazardous materials, making transport of concentrates and storage of mine waste subject to stricter and more costly regulation. The problem is one the industry is keen to avoid."

Jan 1, 2009

Mine Evaluation Engineering , Operational and Social evaluation. Focus is on what opportunities are available. Social ??History ??Past Management Practices ??Community / Available labor force Mining Method / Equipment ??Competent rock ?little support required, no backfill ??Shallow mining ?ramp mining, no shafts or hoisting ??Large scale mining potential ??Simple rock breaking and crushing on surfaceMill Process ??Straightforward gold liberation process Create a Plan / Create a Team Following the feasibility 44-101. Key people were hired and a full operational Business Plan was developed. Focus is on how to get the job done. ??Scoping Study / Pre-Feasibility / Feasibility ??Operational Business Plan ??Hire key people ??Purchase key equipment

May 1, 2006

By Y. F. Jiang, K. Fang, Q. Q. Jiang, Q. Wu

Inter formational sliding of bedding planes between two different rock types in Badong formation is an important reason that leads to the instability and fracture of rock mass in this stratum. There are no specific research achievements on bedding planes between two different rock types in Badong formation. In order to study the shear mechanical properties of bedding planes between two different rock types. This paper using the software of particle flow code (PFC) and JRC model to establish several typical structures of different roughness coefficient of surface morphology based on the laboratory tests on silty mudstone and marlite in Badong formation. A great deal of numerical shear tests were carried out by ball production, radius expansion and servo infliction. The research results are as follows: First, shear strength of Badong formation is found to vary between that of silty mudstone and marlite isotropic planes by analyzing shear strength of the homogenous bedding planes and inhomogeneous rock types, we can find that the shearing strength in Badong formation is between silty mudstone and marlite isotropic planes and which is closer to the shearing strength of silty mudstone isotropic planes. Second, the basical friction angle of bedding planes between two different rock types in Badong formation is between silty mudstone and marlite isotropic planes and which is closer to the basical friction angle of silty mudstone between isotropic planes. Third, based on the experimental results, an expression is obtained to describe the relationship of the ratio of shearing strength between bedding planes of two different rock types and isotropic planes in soft rock, the rock combination coefficient, and the roughness coefficient. This study has important significance for further research on the shear mechanical properties of bedding planes between two different rock types.

Jan 1, 2015

By Mark G. Lafontaine

Underground 802.11 wireless communications has become widely adopted for automation and communication purposes but maximizing the wireless signal presents many obstacles given the harsh environment as well as the presence of materials and conditions that can reduce signal propagation. Changes in elevations and curvatures in ramp to drift transitions also affect the wireless signal. Based on the requirements of wireless applications such as voice, data, or location tracking, the wireless site survey is the key tool for measuring and predicting signal strength and signal-to-noise ratio. These readings help determine the maximum distance between access points in order to sustain an overlapping wireless signal where required. This paper describes the methodology and tools used for measuring 802.11 wireless signal strength in an underground mine environment in Northern Ontario. The physical characteristics of the mine and the actual recorded wireless signal data will be presented in order for the audience to gain an understanding of the factors that affect signal throughput. Antenna selection used for the site survey will also be discussed as it played a key role in propagating the wireless signal.

May 1, 2013

By B. Goard

"IntroductionCemented backfill has been placed underground in slurry form in Inco Limited's Ontario Division mines since the early 196Os. The slurry was traditionally mixed on surface at between 65 and 70 wt% solids* and transported underground via gravity through a borehole-pipeline distribution system. This method of placement, while simple and dependable, has proven to be costly because of the large amounts of transport water involved.A significant quantity of the slimes buildup on mine levels is caused by the backfill water carrying cement and other fine material out of the stopes. The level cleanup and eventual pumping or hoisting of the slimes and water back to surface result in substantial indirect backfilling costs.The cement that remains in the stope is always overhydrated because of the high water cement ratios that exist. As a consequence, high concentrations of Portland cement must be added to the backfill to produce the fill strengths required for the different mining methods.Pouring backfill at these densities also demands extensive fill preparatory work in the stopes to withstand the hydraulic heads created by the slurried fill. This, along with the delays in pouring necessary to allow for water drainage, result in significant losses in productivity.These negative aspects of slurry placed fill has led Inco Limited to investigate several methods of transporting backfill underground via pipeline, at higher densities (i.e. 75 to 95 wt.% solids). Three separate transport methods are presently being experimented with by the Company's Mines Research Department. Each utilizes a different technique or form of flow transport, i.e. concrete pumping technology, high density slurry flow, and pneumatic conveying."

Jan 1, 1987

By I. H. Warren, Forward F. A

The reduction of aqueous slurries of uranyl carbonate at elevated temperature with compressed hydrogen m the presence of metal catalysts and certain organic promoters has been shown. to yield uranium dioxide. The reduction takes place in a sequence of steps. The purity and sintering properties of the dioxide make it of interest as a starting material for fuel element production. Simple control can be exercised over the surface area and oxygen/uranium ratio of the product during reduction. URANIUM dioxide for fueling atomic power reactors 1s conventionally produced as a powder by simultaneously decomposing and reducing ammonium diuranate with hydrogen in a furnace at high temperature. Fuel elements are then generally made from this powder by compacting and sintering ( 1). In order that elements approaching theoretical density may be obtained,

Jan 1, 1961

By S. L. Zekovic

This paper analysis the medium and long-term perspectives, framework and considered possibilities of sustainable development of RTB "Bor" (Copper mines in East Serbia) after consolidation in the period of transition. The copper mine was opened in 1903. and today is the best quality copper producer on Balcan. This paper are elaborates the problems of privatization, debt, investment, growth of copper production from own mines (and imported raw), opening of new mines, economical efficiency of production, markets, environmental problems and impacts of the recent industry consolidation. The RTB "Bor" is a serious hot spot in Serbia. Unsustainable trends and processes are identified, as follows: open-pit waste dumps, flotation tailings, mining and processing waste waters, air pollution; no efficiency (excessive) using nonrenewal resource in the copper production; inefficiency in the use of energy, water and other inputs in copper complex; transboundary character of emissions of dust; environmental degradation and quality of wide area and ecologically highly risk, etc. Analysing some trends and planning-developmental perspectives and development strategies of company, it might be assumed that in the forth coming period, in parts of the Serbia, the borders areas of Bulgaria and Romania, there is an anticipated increase of ecological risk.

Jan 1, 2007

"This paper presents results of ongoing research being carried out at the University of New South Wales into improved methods for estimating rock mass strength. In this paper the rock mass strength of Hawkesbury Sandstone is assessed. An estimate is first made based on an extensive database of intact rock strength data being collated by the author and the assumption that the rock mass strength can be determined following the GSI approach. The resulting strength envelope is then compared with nine documented case studies where stress induced failure has occurred in tunnels excavated within Hawkesbury Sandstone. The case studies cover a range of conditions:• construction dates from 1880s to 2006• spans from 3.2 to 12.5 m• depths from 17 to 124 m• excavation methods of drill & blast, roadheader and TBM.Finite element modelling is used to assess the likely magnitudes of the stresses present at the time of failure. The finite element models are interrogated to provide the values of major and minor principal stresses in and around the mapped failure zone. Failure and stable points are then compared to the rock mass strength envelope(s) of Hawkesbury Sandstone derived using the Hoek-Brown criterion and spalling criteria. The Hoek-Brown rock mass strength envelope differentiates between the ‘failed’ and ‘stable’ zones remarkably well.INTRODUCTIONStress induced failures of rock masses are fortunately rare in civil tunnelling. However, when they occur they provide an opportunity to calibrate an assumed rock mass strength criterion. This paper compares an estimate of rock mass strength for the Hawkesbury Sandstone with the following cases where stress induced failure occurred in tunnels excavated within Hawkesbury Sandstone.• Cataract & Devines Tunnels of the Upper Canal (Upper Nepean Scheme)• Malabar Outfall Tunnel• Sydney liquefied petroleum gas (LPG) Storage Cavern• Northside Storage Tunnel• Cross City Tunnel• Lane Cove TunnelTwo-dimensional finite element modelling is used to assess the likely magnitudes of the stresses present at the time of the failures. The principal stresses are then compared to the assessed rock mass strength envelope(s) of Hawkesbury Sandstone derived using the 2002 Hoek-Brown criterion (Hoek et al., 2002) and the spalling criterion suggested by Diederichs (2007)."

Jan 1, 2015

By K. Webb, M. Hohn

"This paper reviews the evolving Ontario mining regime for mining industry-Aboriginal engagement and its apparent alignment with court decisions, domestic law, emerging international norms, mining industry rules, and mining firm-Aboriginal agreements, drawing on publicly available commentary from government officials, the private sector, and Indigenous communities. This paper provides a preliminary analysis of the potential implications of the new regime, especially for the mining industry and Aboriginal communities and, on that basis, discusses possible future developments.RÉSUMÉ Le présent article analyse le régime minier de l’Ontario pour l’engagement entre l’industrie minière et les Autochtones et son harmonisation avec les décisions des tribunaux, le droit interne, les nouvelles normes internationales, les règles de l’industrie minière et les ententes compagnies minières- Autochtones en se basant sur des commentaires, disponibles publiquement, d’officiels gouvernementaux, du secteur privé et des communautés autochtones. Cet article fournit une analyse préliminaire des implications potentielles du nouveau régime, surtout pour l’industrie minière et les communautés autochtones et, en s’appuyant sur ces données, il traite des futurs développements possibles."

Jan 1, 2016

By J. A. Relf

The construction of refineries and gas conservation plants in the general Edmonton area in the early 1950's made available large quantities of by-product liquified petroleum gases (LPG). These gases, together with discovery of increasing reserves of natural gas in the Edmonton area, provided Canadian Chemical Company with two of the necessities for petrochemical production, namely, available and reasonably priced raw materials and fuel. This paper outlines the development of the $83 million Edmonton plant from its origin, together with a brief description of the processes and some of the interesting features involved. Several economic aspects of the petrochemical industry are high-lighted including its importance to the local community and the province. The paper reviews the relationship between the oil and gas industry and petrochemical manufacturing and indicates some of the factors that may affect the future growth of the petro-chemical industry in Wes tern Canada.

Jan 1, 1962