Search Documents

By Xaykhamphoune, Ward B

Draglines have been used exclusively for primary overburden stripping at the German Creek Mine complex in central Queensland, where coal has been extracted from a series of ten open cut pits working seams of the German Creek Coal Measures. Due to the dip of the seams, most of the pits have now reached the limit of current economic viability and the emphasis has switched to underground extraction using longwall methods and to a new area of open cut reserves in the nearby Rangal Coal Measures at German Creek East. This area is characterised by weak Tertiary overburden, relatively steep dips and low strength intraformational shear planes at the top and bottom of the coal.The first pit, with a maximum depth to coal of 15 m at the low wall, avoided any major slope failure through use of scrapers to excavate the boxcut and dump the spoil away from the low wall. However, this method was not considered economically viable for the second pit where low wall depths reached 44 m. Following geotechnical investigations the boxcut was divided into a number of zones depending on depth of cover, dip and thickness of Tertiary clay. Slope stability was assessed for each zone using several analytical techniques to ensure that dragline mining would be acceptable. Slope design parameters incorporating various stabilisation techniques, notably an updip trench backfilled with competent spoil to form a low wall buttress prior to excavation of the boxcut panel, were successfully integrated into the mine plan after careful consideration of the complex scheduling to minimise rehandle.

Jan 1, 1992

The relative contents of Au in a series of groundwaters from water bores and exploration drillholes, located near Au mineralisation at Stawell, Ararat, Clunes and Ballarat in central Victoria, were found to be clear indicators of relative proximity to mineralisation in each region. In the same series, waters with anomalous concentrations of As distinguished Au mineralisation in bedrock from secondary palaeochannel or deep lead Au. In some groundwaters, acid pH values, high sulphate relative to other anions and detectable concentrations of reduced Fe reflected sulphide minerals associated with bedrock Au deposits. Close to some ore zones, locally anomalous groundwater concentrations of Mn reflected the Fe carbonates that accompany Au in these zones. In addition, elevated concentrations of other elements provided geochemical signatures for the aquifer lithologies associated with Au mineralisation. Of the lithological indicators Co and Ni, U and F, Rb and Cs, Mo and Li respectively reflected the mafic, felsic, potassic rich and quartz zones, principally in the Stawell mine area and to a lesser extent those at Clunes and Ballarat. Mineral stability diagrams, based on groundwater activities of K', Mgt and H`, demonstrated that a series of ore-zone groundwaters follow a trend that conforms with a biotite to sericite to kaolinite alteration sequence in aquifer mineralogy. This is a good illustration of how present day groundwaters under surface conditions can reflect the underlying mineral sequences that accompany these Au deposits. These observations around mine areas suggested that groundwater chemistry could provide a rapid and cost effective method of assessing prospectivity for An of extensive areas in central Victoria. To test this, regional sampling and analysis of 355 bore waters was carried out in a region where potential An bearing rocks are covered by Mesozoic and Cainozoic sediments and volcanics. Contoured elemental abundances and distribution from this program indicated five zones in which groundwaters had elevated Au and despite the cover, appeared to reflect variations in the underlying Palaeozoic rocks. Three of the Au zones could be in terrain affected by extensions or intersections of faults, a feature in common with the established Au deposits in central Victoria. Reflections of concealed Palaeozoic rocks included a possible zone of concealed Cambrian greenstones that coincides with three of the Au zones. It was concluded that each of the An zones represents a groundwater Au focus that warrants follow-up exploration.

Jan 1, 1997

By Waladan M, Elliot B, Rankin W. J

A survey was undertaken on the Kalgoorlie Nickel Smelter in which samples of slag and matte were taken along the length of the integrated flash smelting furnace and analysed to determine the variation of nickel and iron concentration. At the same time the oxygen potential of the slag and matte was measured using disposable tip solid-state oxygen probes. The results show that the oxygen potential of the slag is higher than that of the matte and that both decrease from the reaction shaft end to the slag tap hole end of the furnace. The slag and matte are not at equilibrium except towards the tap hole end. Reduction of nickel and magnetite from the slag occurs before the slag enters the slag-cleaning appendage by reaction with iron in the matte. Thermodynamic modelling and laboratory experiments showed that the equilibrium nickel and magnetite contents of the slag in the absence of a carbonaceous reducing agent are about 0.4 per cent and 7.5 per cent, respectively. A carbonaceous reductant is required to obtain a lower nickel content in the slag.

Jan 1, 1991

By Carthew J

For more than 30 years shearer loaders have been the most important winning machines for,longwall mining. While the machines of the first generation had a driving power of only 100 or so kW, the present day shearer loaders may be powered by more than 1000 kW. Daily outputs of 24000 tonnes have now been reached, but this still does not set a limit. If the deposit conditions allow, further increases are possible. This requires the optimum coordination of all system components. For this paper the use of coal plows has been of little import as plows have found no favour, and nor are they likely to do so in today's economics in Australian coal mining.

Jan 1, 1988

This paper discusses the use of tapered roller bearings in conveyor idlers. It shows that in medium and high capacity systems, tapered roller bearings can offer significant cost and performance advantages. In the next ten years, conventional conveyors will face increased competition from unconventional belt conveyors, pneumatic systems, pipeline "slurry" systems, unit trains and so on. The conveyor industry must meet these challenges by innova- tive use of technology. Conventional belt conveyors must continue to show the lowest cost per tonne-km or lose their position in the market. Tapered roller bearings can contribute to the achievement of this goal. The concurrent resources boom and liquid fuel crises may well see a decline in the use of heavy trucks for bulk material handling over moderate distances 10 to 50 km. There appears to be a trend in the conveyor industry to go to higher speeds with improved belting in conven- tional widths. The transmission of more material over a given period of time will place more demands on conveyor idler bearings. Australia has in general followed the European practice of using deep groove ball bearings in conveyor idlers.

Jan 1, 1978

The Oregon-Idaho graben evolved after widespread Uwleiitic flood basalt volcanism associated with the arrival of the plume head of the Yellowstone hotspot beneath southeastern Oregon approximately 17-16 Ma. The north- to north- northeast-trending, 50 km-wide graben evolved between 15.5 and 10.5 Ma during east-west extension. The graben is part of a middle Miocene back-arc rift (1,100 km long) that includes the northern Nevada rift, the Baker and LaGrande grabens, and the Chief Joseph dike swarm of the Columbia River Basalt Group. The graben ceased to be a volcano- tectonic depression as the cross-cutting western Snake River plain began to evolve at approximately 10.5 Ma.

Jan 1, 1995

Digital computers, by virtue of their capacity for high speed repetitive calculation at low cost, are finding increasing application to routine calcula- tions in the mining industry. In this paper techniques are shown whereby the use of computers can be extended to more complex tasks. The regular calculation of grades and tonnages of material to be extracted from specified areas of an operating open pit is a necessary part of production planning. In this paper it is shown how these calculations can be carried out by computer. thereby freeing planning staff from manual calculation. An operating open-pit mine can be described in terms of drill logs, geological ore boundaries and pit perimeters at various levels. These form the data base which must be suitable for frequent updating to incorporate new information. A suite of computer programmes is described which operates on this data base to calculate tonnages and grades of ore within extensions to the perimeters as indicated to the system by planning staff. Possible future extensions are discussed.

Jan 1, 1971

The Vertical Crater Retreat (VCR) mining method was used to mine two rib pillars at New Broken Hill Consolidated Limited (NEHC) mine at Broken Hill. Experience gained in a trial VCR pillar stope was applied to the design of Panel 3CN pillar (P3CN). Restricted access and a central sandfilled plug in this pillar necessitated the use of angled blastholes and blasting of the stope in two sections. Borehole surveys and close charging supervision were necessary to block, charge and stem the spherical charges in the correct position. The laver sections of the VCR stope with rock walls attained an average slice advance of 2.2 m whereas the higher section of the st.ope between cemented fill walls attained an average slice advance of 3.4 m. Achieved fragmentation was extremely fine. External dilution was assessed at less than 10 per cent. A cement consolidated sandfill exposure of approximately 1300 m2 stood vertically with no significant slumping.

Jan 1, 1983

By L Terrusi

The Bungaroo Valley hosts a concealed Tertiary channel iron deposit (CID) along a 17 km stretch of its length. Bungaroo Valley is approximately 0.5 km wide upstream at its easternmost extent, and 3.5 km wide downstream where it joins the Jimmawarrada Creek. The valley follows the axial trace of an anticline that plunges gently to the southeast, and the CID infills the valley. Mineralisation extends to a depth of 230 m below the surface, and almost the entire deposit occurs below the water table. Bungaroo Valley cuts through the Buckland Hills and is bounded to the north and south by steep scarps capped with the resistant Dales Gorge Member of the Brockman Iron Formation. Basement rocks are believed to be mostly Wittenoom Formation shales and dolomites, with Mount McRae Shale and Mount Sylvia Formation also present. Deep, localised depressions appear at the base of the CID sequence towards the north edge of the upstream section of the valley, while downstream the basal CID contact is relatively flat and shallow. In both cases the profile of the CID surface closely mirrors that of the basal contact. The localised depressions seen in the upstream basal CID contact produce significant variations in CID thickness of up to 100 m over short strike distances. This uneven palaeotopography is most likely due to eddying and waterfalls forming within the riverbed prior to CID deposition during a time when the water table was much lower than at present. It may also be associated with possible karsting in an underlying dolomite unit and subsequent syn- or post-depositional collapse of the overlying CID. The irregular basal contact of the Bungaroo CID sequence has implications for mining in terms of pit design and resource accessibility.

Jan 1, 2007

Rheology is the science which deals with the deformation and flow of matter. Thus rheology is concerned with the flow of any material. The mining industry is concerned with digging things out of the ground, extracting the good stuff and throwing away the bad stuff. In the upgrading processes associated with mining, ie mineral processing, wet techniques are used where the primary material being handled is a particulate fluid, ie a suspension. After the processing operation, with the concentrates extracted, what is left behind generally is a wet material in suspension form, which may or may not contain reagents harmful to the environment. The amount of waste generated in any of the mining processes is large, in fact, the mining industry is the largest generator of solid waste in Australia. In order to minimise the waste generated within the industry it has become of interest to handle the particulate fluid wastes, or suspensions, at high concentrations, thus removing water and some of the reagents which may be harmful to the environment. The resultant highly concentrated suspension is a non-Newtonian fluid. Rheology deals with the flow of non-Newtonian fluids; therefore a combination of rheological understanding of high density suspensions, in conjunction with an understanding of the environmental problems being faced by the mining industry, can and has led to improved methods of waste disposal in the industry, ie waste minimisation. This paper describes the progress that has been made in the development of dry disposal technology in the mining and minerals industry in Australia.

Jan 1, 1998

By Carter J. P

A two year study into the effects of coal mining induced subsidence on cliff lines was undertaken by the Department of Mineral Resources with the support of a grant under the National Energy Research, Development and Demonstration Program. A new monitoring technique, using an Electronic Distance Meter and acrylic reflectors attached to the cliffs, provided safety for the surveyors and extensive and accurate three dimensional displacement data on the movement of the cliffs as they were being undermined. The study report included many graphs showing the measured vertical and horizontal displacements, differential subsidence, tilts and strains and included analysis of these movements with various parameters, such as, seam thickness, depth of cover and distances between the reflectors, longwall face and the edge of the chain pillar. Some of these graphs are presented in this paper and could be used, with caution, to predict subsidence movements around other cliff lines, after allowing for differences in geology and mining layout. A mechanism is suggested as an explanation for the observed high horizontal movements around the cliff lines. Sixteen percent of the overall lengths of cliffs that were undermined during the monitoring study fell and the contributions of various factors that appeared to influence the cliff falls are discussed. It is concluded that no single factor dominated as the major cause of the cliff falls and, often, many factors combined to cause cliff face instability.

Jan 1, 1992

Extraction under very mild conditions - a few minutes at room temperature with poor solvents - yields results characteristic of surface properties for a variety of coals. Such superficial extractions preferentially remove long-chain aliphatic compounds. As coal becomes more oxidized, less of these yellow- colored compounds is extracted, forming the basis for a simple colorimetric test for coal surface quality. The fact that these aliphatic compounds are responsible for surface hydrophobicity is supported by good correlation between extraction results and floatability, which decreases with decreasing extractability. This extraction test is very sensitive to oxi dationb even the effect of heating for an hour at 100 C can be detected. A second extraction test using mild alkali conditions has shown good correlation with plant dewatering Operations.

Jan 1, 1986

By Hoskings AD

Bolting forms a prestressed elastic layer of rock which is capable of supporting loads at right angles to the bolted surface. Investigations on rock bolting made with a number of different models give rise to empirical and theoretical prin- ciples for the formation and action of the layer. In the models, flat and arched layers of many materials were used simulating rock conditions ranging from closely interlocked blocks to fragments of various shapes. Results of observations made in the underground works of the Snowy Mountains Scheme are related to the mode of action of bolted surface layers of rock. There is abundant experimental, theoretical and practical explanation for the well-demonstrated capability of bolting as a means of rock support.

Jan 1, 1971

The Charters Towers goldfield in northeastern Queensland produced over 206 tonnes of gold from gold-quartz veins hosted by Mid-Palaeozoic granodiorite, tonalite, diorite and to a lesser extent amphibolite-grade meta-sedimentary schist and meta-igneous rock. Mineralisation occurs in grouped, moderately dipping shear zones with altered wallrock rafts and a complex network of quartz veins.Over 75 per cent of the production came from three main vein systems in the central goldfield: the Brilliant, Day Dawn and Towers Hill vein systems.The Brilliant vein system is hosted by undeformed tonalite and contains north-plunging oreshoots on a north-dipping main fissure and on shorter east-dripping hangingwall fissures. The Day Dawn vein system is localised along a north-dipping dyke at the contact of two deformed granitoids in a brittly reactivated mylonite, where horizontal oreshoot plunges may be related to the original megascopic undulations in that structure. The Towers Hill vein system is hosted in two granodiorite types and has multiple ore controls.Structural analysis indicates that the distribution of the oreshoots within the vein systems is variously controlled by the primary fabric and igneous contacts of the granitoid host rocks. Splaying, changes in dip, and fissure intersections are the main controls. The largest vein systems are both in reactivated shallow-dipping mylonite, or in fissures in younger undeformed granitoids. Each vein system lies in a separate structural domain, usually where older east-striking structures are preserved.

Jan 1, 1990

Mineral resource and ore reserve classification defines the risk associated with quoted resource tonnes and grades, allowing the interested party to make a judgement as to the `worth' of the resource statement. The JORC Code and Guidelines (1992) are now well entrenched as the foundation upon which gold and base metal deposits in particular are publicly reported. There are three categories of resource, namely Measured, Indicated or Inferred reflecting decreasing levels of confidence. The ore reserve, that is the economically mineable part of the resource, is classified as Proven or Probable and can only be drawn from the Measured and Indicated resource categories. As summarised by Stephenson (1995), resource/reserve classification has been an issue ever since the earliest days of mining in Australasia where, like elsewhere in the world, the industry, for a long time, lacked firm reporting guidelines. Those currently adopted in Australasia as the minimum standards for companies reporting to the Australian Stock Exchange (ASX) have been developed and revised since 1972 by The Australasian Institute of Mining and Metallurgy (The AusIMM), the Australian Institute of Geoscientists (AIG) and Australian Mining Industry Council (AMIC). Debate is now underway in terms of adopting an international code. The Code specifically does not attempt to regulate either the classification technique nor the method of estimation of the resource/ore reserve, but rather places the responsibility for this task on a `Competent Person' whose experience will decide the appropriate approach for a given commodity/orebody. The Competent Person must be a Corporate member of either The AusIMM or AIG with five years experience `relevant to the style of mineralisation' under consideration.

Jan 1, 1996

By Shoobridge PH, Firkin GR

The Imperial Smelting Process blast furnace (ISF) of the Sulphide Corporation Pty Limited zinc/lead smelter at Cockle Creek, New South wales, has in recent years greatly increased its consumption of low grade feed materials, and as a consequence has experienced periods of unstable furnace operation. Routine examination of production sinter, including softening characteristics and micro- examination, showed that the problems had been caused by an increasing silica content in sinter. The silica entered a low melting point glass phase containing calcium and lead oxides. The relative volume of this phase increased until it formed a continuous matrix in the sinter structure and this made the sinter more likely to soften at lower temperatures. Premature softening caused loss of operating stability in both the shaft and hearth of the ISr. The required sinter structure for ISF smelting was found to consist of a network of intermeshing, refractory crystals which provided skeletal strength for sinter lumps even after the glass phases had begun to soften and melt. With an understanding of the importance of microstructure and softening temperature of zinc/lead sinter and the progressive identification of those factors in sinter production which affect the microstructure, a significant improvement in stability of operations has been possible.

Jan 1, 1980

By Morley C

The Mount Charlotte gold mine is located 0.75 km east of the General Post Office in Hannan Street, Kalgoorlie WA and about 3.5 km north of the Fimiston Operations on the famous Golden Mile.Mechanised underground bulk-mining at Mount Charlotte has been in continuous operation since 1963. For the 30-year period ending December 1992, the mine produced 22 million tonnes (Mt) of ore for a recovery of 2.73 million ounces. During 1991/92, the mine produced 1.53 Mt of ore at a head grade of 3.15 gramshonne (g/t) for a recovery of 135 822 ounces.The principal ore source at Mount Charlotte has been the Charlotte Orebody which is now largely mined out. Since 1990, approximately 75 per cent of production has been sourced from the Reward Orebodies. The Charlotte Orebody was a relatively homogeneous quartz stockwork with simple geometry and average bulked grades in the range of 4.0 to 5.5 g/t. This is in contrast to the Reward Orebodies and the more recently defined Charlotte Deeps and Maritana Stockworks, which have complex grade distribution and geometry with lower average bulked grades (2 to 4 g/t). The lower grades are principally due to the decreased density and volume of stockwork venation and related vein halo alteration. Typically, these stockworks comprise a patchy mosaic of quartz veins and vein swarms, with irregular distribution and geometry within the quartz gabbro host rock.

Jan 1, 1993

Daily geological mapping of the Panguna porphyry copper/gold system since mining began in 1971 has provided a good basis for resource estimation and mine planning as the mine and estimation methods have advanced. Geology defined during evaluation and early mining has been substantiated and many smaller features have been better defined or identified. Breccias, pebble dykes, major structures and location of lithology contacts important to short term planning and long term pit slope stability have been defined. Correlation of copper and gold with breccia zones is quite striking and was not fully appre- ciated at the end of evaluation. Pit mapping geology, and diamond drill geology and assays, are now routinely added to a Geological Data base on computer, which forms the major geological data base for modelling the deposit. Geology from diamond drill logging, updated by pit mapping, and assays from diamond drilling updated by blast hole assays have been incorporated in a 45 bench deep 486 000 block computer based block model which forms the basis for long and short term planning. The introduction of pre-concentration scre- ening, based on the distribution of mineralisat- ion and fracturing, puts more emphasis on the definition of grade distribution at low concent- ration and on structures in the rock. Geostatistics is now used for resource estimation and has produced acceptable estim- ates. but these need to be refined, particularly in peripheral, low grade areas of the deposit.

Jan 1, 1987

Gold and copper mineralization in the Parkes area is hosted by a meridional sequence of Late Ordovician to Early Silurian igneous and sedimentary rocks on the central northern edge of the exposed Lachlan Fold Belt. The mineralized area straddles two zones separated in part by the Parkes Thrust and exhibiting different styles of deformation and mineralization (Figure 1). The western zone is characterized by gently folded rocks, with shallow dips and weak to non-existent axial plane cleavage. Faulting is restricted to directions oblique to bedding. Numerous occurrences of minor copper mineralization are known, but of recent national importance is the discovery of the Coradgery- Goonumbla porphyry copper-gold deposits by Geopeko Ltd. A resource in excess of 250 million tonnes has been delineated (Jones, 1985), and this represents the first porphyry deposit of sufficient grade and tonnage to be potentially mineable in New South Wales. The eastern zone is much more strongly deformed. Folding is tight with strongly developed axial plane cleavage. Faulting is abundant both parallel and oblique to bedding. Quartz veining is also abundant, and a narrow belt of gold mineralization adjacent to the Parkes Thrust stretches from Forbes in the south, through Parkes and Peak Hill, to Tomingley in the north. Over 31 tonnes of gold have been produced from this gold belt, mostly before 1914, and now three deposits show good potential for redevelopment - Peak Hill, and the London-Victoria and Lachlan lines of lode.

Jan 1, 1987

By Will D

This presentation is to outline the current practice of mechanised stoping a one-metre wide, gold bearing ore body to optimise fragmentation, minimise dilution and reduce stoping costs.Coolgardie underground operations have historically been mined using traditional shrink stope methods, but in this recent economic environment (with falling gold prices and high costs of traditional methods) it was necessary to look for alternative methods in order to reduce costs and increase productivity.Although still in a learning and refinement phase, CGNL is satisfied that it is feasible, practical and more economic to use mechanised long up-hole stope and long-hole rising methods to significantly reduce the mining cost, reduce dilution, increase safety and increase productivity three-fold compared to traditional airleg methods used throughout the Fasten Goldfields.

Jan 1, 1993