Search Documents

By K Ellis, B Lumsden

A full-scale statistically-based on/off plant trial of a new flotation conditioning technology designed to improve fine mineral recovery was undertaken to determine whether the recovery of selected fine sulfide minerals can be increased. The technology is selective for certain sulfide minerals only, including chalcopyrite and sphalerite. The technology has been shown to selectively aggregate the fine chalcopyrite and sphalerite minerals giving increased flotation recovery. The plant trials have shown an increase in the mineral recovery, without decreasing selectivity. Size by size recovery shows a significant increase in the fine (

Jan 1, 2005

By Aziz NI

There are a number of methods available for the determination of the fracture toughness of rock. Some of the most recognised methods include the hollow pressured cylinder, the short-rod, the chevron - edge-notched round bar in bending and the disc-shaped compact specimen. Most of these tests are difficult and expensive to conduct. In this paper the simple Brazilian testing of discs for tensile strength has been used to determine their fracture toughness. Tests were conducted on six different rock types and the values of the fracture toughness obtained for each type are in close agreement with the results of the well recognised the chevron edged types. Details of the tests, and analytical validation of the technique, are presented

Jan 1, 1992

By P Cleary, G K. Robinson, J Hilton, P Wilson

Concern has been expressed that Vezins can be biased when used for sampling fine materials if the cutter speed is as high as the 0.6 m/s which is often used. Using modelling techniques that consider airflow as well as particles, we have endeavoured to investigate sampling bias as a function of the size of fine particles, cutter aperture, cutter speed, shape of cutter blades, and the size of the gap between the inlet pipe and the cutter blades. Using crude estimates of the rate of airflow and a simple model of a single particle moving through air led to an approximate rule that bias will not occur due to mechanisms related to airflow for particles larger than about 200 microns; and bias will always occur for particles smaller than about 40 microns. For particles between these size limits, the extent of bias depends on particle density, cutter speed and cutter geometry as well as particle size.CITATION:Robinson, G K, Wilson, P, Hilton, J and Cleary, P, 2012. Avoiding bias when using vezins for sampling dusty materials, in Proceedings Sampling 2012 , pp 109-114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By J F. Costa, A Grigorieff

Coal mining reclamation is a worldwide concern. This paper presents a Brazilian example where the economic aspects of reclamation are considered. The basic goal of the study is to transform the reclamation procedures into an economic process by integrating the use of land after reclamation and developing profitable post operations. Some of the activities considered in this case study include: using of the coal pit as a landfill, considering appropriate landfill design and construction; using the area for forest development; and developing grassland, forests of native species and the construction of ponds for fishery. This study will conclude that the mined area is: capable of storing large quantities of waste at a competitive cost and at a low environmental risk; commercial forest development is economically feasible; and the lakes and other reclaimed areas can be integrated into the landscape creating a fresh water supply and an area to raise cattle.

Jan 1, 2005

By E Jamieson

For a number of years, Alcoa World Alumina Australia (Alcoa) has been investigating opportunities to produce economically viable products from bauxite residues. Three of these potential products are described here, being Red Sand, ALKALOAM« and REDLIMETM.Red Sand has a nominal particle size of +100 micron and is physically little different to crushed bauxite from which it is derived. In AlcoaÆs Western Australian refineries, Red Sand constitutes up to half of the residue going to impoundment areas. Initial testing indicates that this sand could be processed to provide an acceptable general landfill material, a construction back fill or a material suitable for road base construction. ALKALOAM« is the fine-grained residue often referred to as red mud. A great deal of work has been done to show the benefits of adding this material to sandy soils, which are common in coastal regions of WA. ALKALOAM« has properties that can elevate the pH of the acidic soils and also retain phosphorous, reducing overall fertiliser use and protecting sensitive waterways. REDLIMETM is a by-product of the refining process. This material has a high acid neutralising value. REDLIMETM could be more effective at pH control than most available products because of the fine particle size and sodium carbonate that remains with the product.

Jan 1, 2004

By M Norbert, D O’Connor

The mainline running tunnels for Legacy Way comprise two tunnel boring machine (TBM) driven tunnels. Both TBM drives commenced at the Launch Portal adjacent the Mt Coot-tha Road. Excessive surface settlement arising from tunnelling would have had a significant impact to the road infrastructure. The geological structure above the tunnel springline is a mixture of fill, residual soil and weak rock. Given the combination of low ground cover and weak ground materials, along with the use of an open face TBM, an oversize pipe umbrella system has been installed above the tunnels. This pipe umbrella system is similar to that commonly adopted in conventional mined excavation support in soft ground except that the steel pipes are substantially larger in geometry and filled with concrete. It is acknowledged that similar systems with oversize pipe umbrella have been adopted elsewhere in the world in other projects. These systems often comprise of a full arch formed by conjoining oversize steel pipes (in contact only). By aligning the pipes in contact, the arching behaviour of the steel pipe would have been enhanced. However, this poses a degree of construction difficulty due to excavation and installation method of the pipes. The Legacy Way pipe umbrella system only consists of a partial arch at the tunnel crown and each pipe is spaced approximately 1200 mm apart with 900 mm diameter pipe, leaving a gap of approximately 300 mm between pipes. A reinforced concrete portal block was used to support the exposed ends of the pipes.This paper reviews the design analysis, the recorded deflections from the pipe umbrellas and surface monitoring during TBM launch and revisits the analysis using the newly available RS3 program, from Rocscience for 3D analysis of geotechnical structures.CITATION:Norbert, M and O’Connor, D, 2014. Starting the journey – launching of the Legacy Way open face tunnel boring machines in mixed face ground conditions, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By C Robertson, J Campos

The South African mining industry first experienced en-masse use of electronic detonators in the Narrow Reef environment using AELÆs ElectrodetÖ pre-set delay system. In recent years, programmable systems such as AELÆs SmartdetÖ have also established their position, and within both AEL and the mines there has been important learning around the strengths and weaknesses of these systems. In general, the fixed delay systems tend to be more easily appreciated by less-skilled work teams, and are very well suited to simple layouts, especially long, narrow blasts. However, development of programmable row controllers and series delay inserts has greatly expanded the field of usefulness of these systems while retaining most of the simplicity of use. The programmable systems are immensely flexible and therefore able to function under any condition, but require a higher level of discipline and knowledge. Much has been done to address this issue and make the systems user friendly, so the systems have converged to some extent. These systems are both valuable tools for achieving control over blasting in underground and surface applications. The choice of system is very dependent on the prevailing conditions. Accurate timing with electronic enhancements continues to show an increasing range of benefits to mining operations. There is a strong parallel with non electronic initiation systems which helps to understand the appropriate use of the systems.

Jan 1, 2001

By J B. Pateiro-Fernßndez, M Fuchsschwanz, G Deissmann, S Ahmad

Quang Ninh province is the most significant coal producing region in the north of Vietnam. The Nui Beo Coal Company (NBCC) operates open pit mines in Quang Ninh province and the waste overburden produced is dumped as sidehill fill in the Chinh Bac waste dump site. In the past, no special consideration has been given to the environmental impacts during the dumping operations. The mine waste is transported in trucks from the mine site to the dumping site and the loading, hauling and dumping operations are the main sources of dust emission. Rain events, especially during the rainy season, cause the generation of contaminated surface water as well as seepage of water through the dump at a number of locations. The existence of cracks at the top of the dump can pose serious stability problems with heavy rain events leading to failure of slopes which can potentially disturb vast areas of land currently used for agricultural purposes and human settlement. For sustainable development at the Chinh Bac waste dump site in the future, apart from the social and economic considerations to be assessed, there is an absolute necessity for environmental protection measures to be in place both during and after the dumping of the mine waste overburden. Research Association Mining and Environment in Vietnam (RAME) is working to develop and implement concepts for the mitigation of environmental problems emerging from dust, contaminated water and lacking slope stability to ensure successful rehabilitation of the coal mine waste dumps in the north of Vietnam. Within the framework of RAME, the Institute of Mining Engineering I (RWTH Aachen University) is managing and working to develop the stabilisation concepts for the solid mine waste dump in collaboration with the Chair of Geotechnical Engineering (RWTH Aachen University), Brenk Systemplanung and the Vietnamese group of companies VINACOMIN (Vietnam National Coal-Mineral Industries Group). The most economical and environmentally sound operations, as well as locally adaptable environmental protection measures, are essential for the sustainable development of the dumping operations at Chinh Bac dump. This paper describes the dump site and the sustainable development possibilities with an emphasis on the environmental protection and stability problems at the Chinh Bac waste dump.

Jan 1, 2009

By G W. Swana

Elastoplastic parameter is a parameter that describe how much materials behave elastically up to certain stress states and plastically thereafter (Hudson and Harrison, 1997). In the continuum analysis, two main parameters of the elastoplastic parameter are modulus elasticity and Poisson’s ratio. In the slope, elastoplastic parameter holds the main role for stability related to deformation in ductile type of rock. There’s a limitation to determine elastic or plastic deformation at the field for ductile rock type. Field manifestation commonly showed that there was no accumulation zone during and after the sliding failure mechanism, in other hand, at the research area, manifestation of deformation at the toe of slope only indicated by bulging shape. This paper will focus at the sliding failure occurred at Coal mining Pit Y owned by Arutmin Indonesia, which according to failure investigation report similar with the condition described above. This paper also will be based on two hypotheses, first hypothesis is claystone rock mass has not been reached plastic deformation yet and the second hypothesis is there is a chance that elastoplastic parameter of the rock mass has been changed during the deformation/sliding failure process. Research method of this paper are back analysis using probabilistic analysis in Finite Element Method (FEM), which conducted before and after failure. Then, the result of the displacement or deformation of the analysis will be checked with the actual deformation shape. Meanwhile, the change of the elastoplastic parameter will be analysed and interpreted. This paper hopefully able to be developed to study about elastoplastic behaviour of rock mass in actual condition and the influence of another uncertainty factor which determine the slope stability.

Nov 29, 2022

By G Stephenson, G MacDonald, A Yeomans, S Sinclair, V Knott

Rio Tinto has actively committed to progressive reclamation, concurrent with commercial operations, at its Diavik Diamond Mine. The most significant piece of progressive reclamation undertaken at Diavik to date has been the construction of an engineered thermal rock cover for the mine’s largest waste rock storage area. This 80-metre-tall and 2000-metre-long area is known as the Waste Rock Storage Area – North Country Rock Pile (WRSA-NCRP) and contains the operationally segregated potentially acid-generating waste rock mined over the last 20 years. As part of the mine plan, an opportunity was recognised where a limited 1.5 per cent of the WRSANCRP surface area was required for storage of the balance of life-of-mine generated waste rock and a decision was made to advance the closure design almost a decade ahead of final closure. With over 12 860 000 tonnes of material placed and 57 443 dozer hours logged since cover construction, progressive reclamation on the WRSA-NCRP is scheduled to be complete in mid-2023, three years before planned cessation of commercial operations in 2026. The progressive closure of the WRSA-NCRP demonstrates Rio Tinto’s commitment to not only closure, but modern best practices with integrated mine closure. Over the past seven years, Diavik has overcome multiple implementation hurdles for this project including the psychology of operational standby, the financial mechanisms required to support closure, working within the constraints of a mine plan and the associated operational organisational structures. This paper outlines the lessons learned to provide an example of successful integrated mine planning for closure. The North Country Rock Pile project had three major learnings which resulted in an effective organisational structure that allowed for the execution of an integrated planning model for progressive closure. The initial hurdle the project faced was adapting the psychology of an operational open pit mining team. The team was an experienced mining group who came in with the perspective to target the shortest haul possible resulting in the initial perception that the longer haul of material to the NCRP was an un-necessary task impacting operational performance metrics. After the installation of an improved dispatch tracking system and performance metrics, it was possible to demonstrate that the mine was shovel constrained. This showcased the short haul was generating an increase in queue time not production. With updated performance metrics, the team was aligned to target a decrease standby through haulage to the NCRP. These performance metrics had to be reinforced by financial mechanisms. The operations team was able to offset costs by charging time to the capital project set-up for the closure of the NCRP. This allowed the operations team to receive credit for time that would have otherwise likely been standby. As well, the progressive closure project was able to receive the benefit of not having to incur costs for the drill, blast and load as that was done as part of the operation. This was a significant benefit to the project and one of the primary drivers for the early approvals of the work as the project costs were limited to the incremental haulage distance and placement of the material. Life of Mine Conference 2023 | Brisbane, Australia | 2–4 August 2023 114 While the combined operational and progressive closure approach provided financial advantages, it did result in the project being constrained by the operational activities. A traditional capital project is managed through a linear execution plan where the deliverables within a project are within the realm of control of the project execution team. However, the NCRP project had to be continuously adapted to the outcomes of the pit operations. This included geotechnical constraints, ore delivery, and other operational delays. To adapt, the planning module had to be dynamic but not reactive to allow for adjustments on a shift-by-shift basis. Based on this requirement the Diavik Closure Projects structure adopted a mine planning format. The team executed a similar planning timeline and reporting structure as the mine operations team, allowing planning to be integrated into the operational planning structures on a daily, weekly, monthly and quarterly basis. This resulted in the Projects team as a core pillar of the mine planning team. The process of continuous improvement spanned six years and has resulted in the project being ahead of schedule and under budget for the project’s scheduled progressive closure completion date of June 2023. The North Country Rock Pile project supports the argument that bulk earthworks progressive closure projects should be integrated into the operational mine plan. If the project is aligned the mine plan it allows for dynamic adjustments which capitalise on evolving opportunities inevitable in an operating mine. These cultural and organisational alignments should be supported by appropriate performance metrics and financial mechanisms to ensure united priorities. The result of this alignment provides long-term financial savings for the business as well as delivery of closure objectives.

Aug 2, 2023

By J G Bastias

It is sometimes necessary to resort to extremes in order to call attention to something that is pertinent to safety in mining. When some of the experts in occupational safety talk about this topic, they usually refer to a 'regulation' established by the Romans which stated that, due to the health hazards, usually death, no Romans but only slaves should work in mining. Since the time of the Roman Empire, a lot of ground has been covered in the field of mine safety. Nowadays, it can be said that occupational safety is being seriously addressed, with the result that the number of mining accidents has reduced dramatically, fatalities in this industry are less frequent, and the rate of accidents compared with other activities, such as construction or fanning, is low. This achievement has been possible initially through government legislation and by procedures established by the mining companies themselves. However, the dilemma for government is whether to regulate and if so, how much. It is pleasing to observe that most companies are establishing working procedures which conform with new government legislation, placing strong emphasis on the duty of care for mine employees. There will always be some regulatory aspects of legislation, and perhaps the best example of this is in the use of mine hoists where there are no international or Australian standards, and the regulations applied are of an empirical nature that err on the side of safety.

Jan 1, 1994

By T Craske, J Sykes, T C. McCuaig, M Jessell, A Trench

The prevalent strategic approach in the mining industry is one of planning. However, it is widely recognised that planning does not work in complex and uncertain situations (Mintzberg, 1994), such as those associated with ‘above ground’ non-technical orebody complexity (Trench, Packey and Sykes, 2014). Mintzberg, Ahlstrand and Lampel (2009) suggest the focus instead should be on strategic ‘thinking and doing’ and using the many ways to think about strategy to make sense of complex, uncertain, and unique situations. They therefore place great value in cognitive flexibility. Scenarios development utilizes several different thinking styles and thus assists with this type of flexible strategic thinking (Figure 1). The ‘Centre for Exploration Targeting (CET) Scenarios’ were developed with the ‘Oxford Scenario Planning Approach’ (OSPA) (Ramírez and Wilkinson, 2016). The OSPA aims more to improve the thinking skills of decision makers, rather than forecasting per se (Wack, 1985a, 1985b). As such, this paper focuses less on the content of the scenarios and instead on the practical value of scenarios in strategizing. CITATION: Sykes, J, Trench, A, McCuaig, T C, Jessell, M and Craske, T, 2018. Strategic thinking about long-term ‘above ground’ orebody complexity using scenarios, in Proceedings Complex Orebodies Conference 2018, pp 60–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By L R. Sousa, M He

Rock burst is common in deep underground excavations and is characterised by a violent ejection of block rocks from excavation walls. It is critical to understand the phenomenon of rock burst and particularly the failure mechanism. Laboratory experiments are one of the ways. For that purpose, a rock burst laboratory test system was developed at the State Key Laboratory for Geomechanics and Deep Underground Engineering at the China University of Mining and Technology, Beijing. A true triaxial test system, designated the Deep Underground Rock Burst Analogue Test Machine, was developed, which can transfer a stress state from three-direction-compression on six surfaces to the compression on five surfaces with one set free. The rock burst experimental system comprises an acquisition of acoustic emission signals, a high-speed recording in order to accurately record the kinetic characteristics of rock fragments ejected during a rock burst event and the possibility of infrared thermography showing the surface temperature of the samples. In this paper, analyses of typical results from rock burst tests are presented with a description of the obtained results. The mechanisms of rock burst are illustrated, and a rock burst classification is proposed based on these laboratory tests. For the control of rock burst, the constant resistance, large deformation (CRLD) bolt or anchor is presented for accommodating the large displacement of surrounding rock masses and absorbing the impact of the sudden release of rock burst while outputting a constant resistant force in response to the external load. The CRLD bolt or anchor has had practical applications in underground mines. Finally, in situ tests performed in a tunnel at Qingshui coalmine, China, are analysed in detail.CITATION:He, M and Sousa, L R, 2014. Experiments on rock burst and its control, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 19–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By DV Boger

Rheology is the science which deals with the deformation and flow of matter. Thus nccology is concerned with the flow of any material. The mining industry is concerned with digging things out of the ground, extracting the good stuff and throwing away the had stuff. In the upgrading processes associated with mining, is mineral processing, wet techniques are used where the primary material being handled is a particulate fluid, ie a suspension. After the processing operation, with the concentrates extracted, what is left behind generally is a wet material in suspension form, which may or may not contain reagents harmful to the environment. The amount of waste generated in any of the mining processes is large, in fact, the mining industry is the largest generator of solid waste in Australia. In order to minimise the waste generated within the industry it has become of interest to handle the particulate fluid wastes, or suspensions, at high concentrations, thus removing water and some of the reagents which may be harmful to the environment. The resultant highly concentrated suspension is a non-Newtonian hold Rheology deals with the flow of non-Newtonian fluids; therefore i combination of rheological understanding of high density suspensions. ill conjunction with an understanding of the environmental problems hero' faced by the mining industry, can and has led to improved methods of waste disposal in the industry, ie waste minimisation. This paper describes the progress that has been made in the development of dry disposal technology in the mining and minerals industry in Australia.

Jan 1, 1998

By Y Peng, D Wannas

In the fine particle flotation technologies being developed today the fine hydrophilic (gangue) particles are usually well dispersed. These highly dispersed fine particles can be recovered into the flotation froth product by mechanical entrainment. Flocculation of hydrophilic particles caused by polymer depressants could potentially reduce the mechanical entrainment of these particles. This paper reports testwork completed on fine particles of several solids, iron oxide, hydroxylapatite, galena and sphalerite, as well as on a relatively coarse quartz sample (-75+38 ¦m). Dodecylamine was used as a collector for the quartz, and several dispersants and polymer depressants, including sodium silicate, sodium metaphosphate, zinc sulfate, potassium dichromate, corn starch, corn dextrin and carboxymethyl celluloses (with molecular weights of both 700 000 and 80 000) were used as flotation modifiers. The major part of the testwork involved flotation tests in a 200 ml flotation column. Both water and solid recoveries were recorded. The degree of flocculation and dispersion was determined by settling tests in 250 ml graduated cylinders. It was observed that flocculation of the fine hydrophilic particles significantly reduced their mechanical entrainment, while dispersion severely aggravated it. Thus, in the flotation separation of artificial mixtures of the -75+38 ¦m quartz and fine iron oxide or hydroxylapatite, polymer depressants that caused flocculation were found to perform better than the ones that did not cause flocculation.

Jan 1, 2005

By S A. Ravishankar

An overview of flotation reagents used in sulfide and non-sulfide separations, from an industrial perspective, is given in this presentation to highlight the current applications knowledge. The historical and theoretical aspects, which are well documented in numerous books and reviews, will only be highlighted, when necessary, to support the theme of this paper, viz critical analysis of reagent research, design, selection and optimisation with an emphasis on relevance to plant needs and practice. The three types of flotation reagents; viz collectors, frothers and modifiers, used currently in the industry are briefly reviewed; pitfalls and gaps, arising from somewhat arbitrary and reductionistic practice in reagent applications, are identified; and the impact of environmental regulations on current and future reagent development is discussed. The importance of frothers and modifiers, which have received less overall attention than collectors, is highlighted. The need for a rational, holistic (or ætotal systemÆ, ætop-downÆ) approach for reagent design, selection and optimisation is discussed with a view to provide remedies for pitfalls and a platform for filling gaps in reagent chemistry and applications, and to develop reagent technology that can deliver robust solutions to plant needs. Flotation Matrix 100TM, a comprehensive package designed at Cytec to incorporate all the elements of the holistic approach û viz definition of mineralogy and plant needs, rule-based expert system rational reagent selection, and laboratory and plant best practices û will also be described.No paper available for this abstract

Jan 1, 2005

By J Ortiz

In almost all copper mining companies, mine planning is done considering different time frames, leading to long-term (life-of-mine) (LOM), medium-term (first three years) and short-term (first year, monthly, weekly, and up to daily plans). Shorter term plans are usually associated with more abundant information, hence models with lower uncertainty. However, they capture more of the variability found on the geological attributes. In long-term models, usually estimation methods tend to hide this variability, providing smoothed interpretations.Medium and long-term plans consider average values for the parameters and optimisation techniques are applied aimed at maximising the economic profit. Short-term plans, on the other hand, are made to comply with the medium-term promises, maximising the use of the available resources (equipment and processing capacities) and dealing with the variability not characterised in the previous planning stages. This generates an important gap between the short-term and the medium and long-term plans. A case study was made using an important oxide copper mine, where the variability found in the short-term plan has a large impact in the productive process, thus reducing the daily ore grade variability is an important goal. In this paper, this planning issue is addressed by creating medium-term mine plans using mixed integer programming which are compared using the output of a simulation of the daily extraction that is aimed at satisfying the daily constraints of the processing plant, the availability of mining equipment and the variability of ore grade. The result shows the expected gap between these mine planning processes, which suggests correcting some of the parameters used in future medium and long-term plans.

Sep 26, 2011

By D Reid

The engineering properties of soils and tailings often exhibit significant anisotropy. One area where this has been well documents is undrained shear strength. Materials sheared in directions close to the principal stress direction in situ, i.e. triaxial compression, typically exhibit higher undrained strengths than those sheared in other directions such as simple shear. Importantly, along the most common critical failure surfaces relevant to tailings stability, whether primarily through tailings or a critical foundation layer, saturated materials are generally much closer to the simple shear loading direction than triaxial compression. Therefore, testing undrained shear strength of tailings or foundation soils in triaxial compression is likely to result in overestimation of the relevant strengths for design. Although these issues have repeatedly documented in the geotechnical literature for over three decades, they are not appreciated sufficiently across our industry. In an attempt to address and highlight these issues, a review is carried out of historical reference to the importance of simple shear loading. Attention is then drawn to the techniques applied in three recent post-failure investigations, where simple shear testing was applied. Finally, some relevant laboratory test results from a recent project in which the author was involved are outlined.CITATION:Reid, D, 2018. Importance of the simple shear loading direction to the stability of tailings storage facilities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 274–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By S Kakara, A Kamaraj, S S. Varanasi, B V. R Mandalika, M B. Shaik

The properties of top slags play a very important role in secondary steelmaking. Fluxes should be chosen based on the ladle furnace (LF) slag requirements like viscosity, melting temperature, sulfide capacity, etc. CaF2 and CaO-Al2O3-based synthetic slags are the most used fluxes in secondary steelmaking to improve slag fluidity and interfacial chemical reactions. CaF2 is obsolete due to fluorine pollution and CaO-Al2O3 based slags have 40–50 wt per cent Al2O3 and 30–40 per cent CaO which is not beneficial for desulfurisation. Yet another drawback is that LF slag disintegrates into fine powder during cooling due to phase transformation C2S (2CaO.SiO2). Hence, there is a need for the development of low melting fluxes with high CaO content and the capability to prevent slag disintegration. The current work studied the effect of 0–9 wt per cent B2O3 on physico-chemical properties and characterisation of LF slags. X-ray diffraction (XRD) analyses were carried out to identify mineralogical phases present in slag and Fourier-transform infrared spectroscopy (FT-IR) analysis was done to understand the changes in bonds of B2O3 added LF slag. The characteristic temperature of slag was determined by a hemispherical method using high-temperature microscopy. Empirical models were used to calculate viscosity, break temperature, and sulfide capacity. FactSage™, ver 8.2 (by GTT-Technologies) simulations were carried out to find the equilibrium phase fractions and percentage of liquid slag at different temperatures. New phases such as Ca11B2Si4O22 and Ca2B3O5 were formed in LF slag with B2O3 addition. Based on the results, 0.5–1.0 wt per cent B2O3 was found to be sufficient to prevent C2S-driven disintegration of LF slag. Also, the melting temperature and viscosity of LF slag were reduced by adding 3–8 wt per cent B2O3 due to the formation of BO3 planar triangular structure and low melting eutectics in slag. Liquid slag started forming at a temperature as low as 800°C when B2O3 is >6 wt per cent. It was found that the sulfide capacity, viscosity, and break temperature of the slag decreased with increasing wt per cent B2O3. Based on the analysis carried out, B2O3 can be a promising fluxing material in secondary steelmaking, for improving the desulfurisation kinetics and valourisation potential of LF slag.

Aug 21, 2024

By A Hughes, S G. Rosin

This paper presents the design and construction approach adopted for the widening and stabilisation of the existing decline tunnel forming part of the Scenic Railway Upgrade project at Katoomba in the Blue Mountains of New South Wales (NSW), Australia. The overall upgrade project included new trains and track, rebuilding of the top and bottom station and installation of a new winch and control system. All the works were undertaken over an eight-month period between August 2012 and April 2013 as part of a $30 M upgrade of the railway.The railway is the steepest cable-driven line in the world at a maximum of 52° extending over 350 m and descending from the escarpment into the Jamison Valley. The track was built in the 1880s for coal haulage and is recognised as a remarkable engineering achievement for its time. The tunnel section extends for about 120 m at the start of the decline and is about 3.5 m wide and 3.5 m high. The tunnel was excavated principally within medium to high strength Banks Wall sandstone and given that the widening only involved about 200 mm of trimming of the crown and sidewall this aspect of the work was not a critical support issue, except at the upslope portal. The tunnel crown however is entirely intersected by a major near vertical shear zone which presented significant challenges for the tunnel stabilisation works.Three-dimensional laser survey scanning was used for definition of the tunnel clearance envelope for the widening, and also to subdivide the tunnel into various geotechnical sections to assist in support design. Specifically oriented rock bolts extending beyond the shear zone into stable rock were used together with mesh, shotcrete and extensive strip drains and flushing points for drainage of the shear zone.Unique aspects of this project were included into the specifications and work methods. This included construction of a mobile working platform for tunnel works, the use of dry shotcrete application, difficult access for rock bolting and limiting vibration during the tunnel trimming works due to the risks associated with crown instability. The works also took into consideration particular safety constraints/work exclusion areas to address the risk of detachment of rock which could mobilise downslope to the track area below. This was required because other works were in progress such as micro-piling and bottom platform works which were being undertaken concurrently with the tunnel work.CITATION:Rosin, S G and Hughes, A, 2014. Scenic Railway Tunnel upgrade in the Blue Mountains, New South Wales – an approach to design and construction, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 607–618 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014