Search Documents

By W. M. Rust, W. D. Mounce

The almost universal acceptance of electrical logging by the petroleum industry calls for a critical examination of the physical bases of the common methods. This is particularly needed for the natural potential log. The conventional explanations are based on the phenomena of electrofiltration and electro-osmosis. However, experimental data show that they fail to give a basis that is quantitatively sound. Moreover, they lead to interpretations of details of electrical logs that are erroneous. It was found experimenlally that when a plug of shale is placed in a chain of dissimilar electrolytes, a current flow results. Experiments on oil-well cores and fluids similar to those existing in wells show that potentials are set up which are in reasonable agreement with those encountered in electrical logging. Doubtless other sources of potential are important but this explanation not only accounts for much of the potential but also clarifies some fairly familiar examples of misinterpretations. Introduction The extraordinary value of electrical well logging as a tool for petroleum engineers and geologists is now so universally recognized that it is not necessary to point out the ways in which it can be useful. It is sufficient to mention only the saving that has resulted from the elimination of much coring that would have been necessary under former practices and the considerable additions to reserves resulting from the discovery of sands missed in coring. Paradoxically, the very remarkable success that has resulted from the application of electrical logging to correlation and completion problems has cost some of its most consistent users dearly.' The fact that some operators have placed unwarranted faith in erroneous interpretatioils of electrical logs does not reduce the value of the logs. It should, however, make one pause long enough to ask why experienced users should be misled. The answer to this question is not hard to find. In nearly every case, the fault has been oversimplification. This is illustrated very aptly by the familiar interpretation and theory of the natural potential log. Recording and Interpreting Logs The natural potential log is extremely simple to record precisely enough for all present-day uses. One needs only an electrode, a cable to lower the electrode through the drilling mud, a recording meter and a surface ground connection. The electrode can be elaborate but need not be. A simple brass rod 2 in. in diameter and 2 or 3 in. long is quite satisfactory. The cable need not be particularly well insulated, nor need it have a very low resist-

Jan 1, 1946

By W. M. Rust, W. D. Mounce

The almost universal acceptance of electrical logging by the petroleum industry calls for a critical examination of the physical bases of the common methods. This is particularly needed for the natural potential log. The conventional explanations are based on the phenomena of electrofiltration and electro-osmosis. However, experimental data show that they fail to give a basis that is quantitatively sound. Moreover, they lead to interpretations of details of electrical logs that are erroneous. It was found experimenlally that when a plug of shale is placed in a chain of dissimilar electrolytes, a current flow results. Experiments on oil-well cores and fluids similar to those existing in wells show that potentials are set up which are in reasonable agreement with those encountered in electrical logging. Doubtless other sources of potential are important but this explanation not only accounts for much of the potential but also clarifies some fairly familiar examples of misinterpretations. Introduction The extraordinary value of electrical well logging as a tool for petroleum engineers and geologists is now so universally recognized that it is not necessary to point out the ways in which it can be useful. It is sufficient to mention only the saving that has resulted from the elimination of much coring that would have been necessary under former practices and the considerable additions to reserves resulting from the discovery of sands missed in coring. Paradoxically, the very remarkable success that has resulted from the application of electrical logging to correlation and completion problems has cost some of its most consistent users dearly.' The fact that some operators have placed unwarranted faith in erroneous interpretatioils of electrical logs does not reduce the value of the logs. It should, however, make one pause long enough to ask why experienced users should be misled. The answer to this question is not hard to find. In nearly every case, the fault has been oversimplification. This is illustrated very aptly by the familiar interpretation and theory of the natural potential log. Recording and Interpreting Logs The natural potential log is extremely simple to record precisely enough for all present-day uses. One needs only an electrode, a cable to lower the electrode through the drilling mud, a recording meter and a surface ground connection. The electrode can be elaborate but need not be. A simple brass rod 2 in. in diameter and 2 or 3 in. long is quite satisfactory. The cable need not be particularly well insulated, nor need it have a very low resist-

Jan 1, 1946

By H. J. Beach, W. C. Goins

The laboratory development and field use of oil well cement compositions* with high resistance to drilling mud contamination are described. Resistance is obtained by adding a I-lb mixture composed of three parts paraformaldehyde to two parts sodium chromate tetra-hydrate for each sack of cement. This mixture neutralizes the cement-retarding properties of quebracho and other tannins, starch, sodium carboxymethylcellu-lose, Ignite, and monovalent salts of lignosulfonic acid. The retarding properties of calcium lignosulfonate are unaffected. The decontaminating mixture may be used in common cement (designated Type I by ASTM specifica-tions,' Class A by API Std. 10A2) or in a slow set slurry prepared from common cement by addition of calcium lignosulfonate. No changes in slurry viscosities or thickening times are caused by the protecting reagents. The method has been used in 185 field jobs where an improved success ratio has been obtained in plug setting. INTRODUCTION Field experience and laboratory investigations have established contamination by drilling mud as a major factor in oil well cement failures. During 1955, 12 attempts were required to set six open-hole cement plugs in the Timbalier Bay field, La. Eighteen to 30 hours elapsed between placing and testing the plugs in preparation for sidetracking operations. Considerations of rig time expense required immediate resetting where soft cement was drilled after a reasonable waiting period. Sea water drilling mud was used in each well and daily additions of thinners, usually lignites, had been required. Sodium carboxymethylcellulose had been added regularly to control fluid loss. The 50 per cent plug failures were attributed primarily to contamination by the mud. Similar experiences can be found in other fields along the Texas and Louisiana coasts where drilling muds normally contain large quantities of organic treating materials. Cement contamination was the subject of a survey by the Mid-Continent District Study Committee on Cementing Practices and Testing of Oil-Well Cements of the API.3 Data collected from member laboratories and released in Sept., 1951, reported the effects of a number of drilling mud treating chemicals on cement. The study revealed that many of the additives, notably the organic materials in relatively small quantities, had marked effects on the properties of cements tested. Severe losses in strength and erratic thickening time resulted from small additions of mud treating chemicals such as quebracho, starch, sodium carboxymethylcellulose, and lignite. The report included no recommendations of methods for overcoming the problem. One investigation of the contamination problem reported the successful use of activated charcoal in setting cement plugs after conventional slurries had failed.4,5 The investigation indicated that an optimum concentration of 5 per cent activated charcoal was effective in combating contamination from 16.7 volume per cent of treated mud. Laboratory and field muds were included in tests and contained varied quantities of ode or more of the following: quebracho, caustic, starch, lime, and calcium lignosulfonate. The function of the charcoal appears to be physical, removing the organic materials by adsorption. The method may be employed in API Class A or Class D (unretarded slow set) cements. The chemical approach presented here is based on

Jan 1, 1958

By A. J. Bowie

The discovery of the auriferous cement gravel deposits in and near Deadwood Gulch, Lawrence County, Dakota Territory, in 1876, created a mining excitement, and rush to the Black Hills. Numerous ten and twenty-stamp mills were built on Deadwood Gulch; Central City and the town of Deadwood sprang into existence, and became the centres of the mining industry of the Hills. Gold quartz deposits were subsequently discovered and located on a so-called mineral belt, extending from Whitewood Creek on the south, to Deadwood Gulch on the north. A northerly group of these quartz locations was purchased in December, 1877, by parties in San Francisco, who formed a company, incorporated under the name of the Father de Smet Consolidated Gold Mining Company. This company immediately commenced the work of exploration The deposits were proved to be extensive, and easily mined, but it was found that the ore, on an average, would not yield more than $10.00 per ton* of 2000 pounds. • At this trine the cost of supplies and materials in the Hills was high. Miners' wages were $3.50 per diem, and custom mills charged $6.00 per ton. The successful working of mines on "the belt" necessitated cheap milling. The ores being of so low grade,f this could be accomplished only with large and economically running mills. To insure the greatest possible economy, the Father de Smet mill

Jan 1, 1882

By A. H. Bromly

The small agricultural village of Santa Barbara, in the State of Guanajuato, has been the center of spasmodic tin-mining operations during recent years. The deposits, so far as I know, are unique, and a few brief notes may be of interest. Santa Barbara, about 12 miles west of San Felipe station on the Mexican National Railway, and at an elevation of 2,400 m. above sea-level, is situated in a flat valley extending east and west, and bounded north and south by broken rugged hills rising about 330 m. above the general level of the valley. Tin-mining operations have been conducted at the Queensland mine, near this village. A small concentrating-mill was erected and attempts were made to smelt the ore in reverbera-tory furnaces. The country-rock of the district for many miles is rhyolite of great thickness. There are some local variations due to differences in cooling, or subsequent alteration or impregnation; but throughout the whole district the principal constituents of the rocks remain the same, viz., free silica, orthoclase-feldspar and sanidine. The latter is especially marked. The crevices and joints of the rock are frequently filled with calcedonic and opalescent quartz. The ore-formation at the Queensland mine is of an unusual nature, consisting of cracks in the rhyolite which have been filled with clay. This phenomenon is largely developed over a width of from 80 to 100 m., in which the principal fissuring follows an approximate direction of north and south. The average dip ranges between 70 and 80 degrees. Some of the fissures hold sufficiently true for a time to afford the impression that they are due to dynamic causes, or earth-movement. This may be true of some of the north by south fissures; but considering

Jan 1, 1906

By R. A. Swalin

IN this paper, the results of an investigation concerning the diffusion of three elements, magnesium, silicon, and molybdenum, in nickel are presented. The work represents a continuation of a diffusion program relating to solute diffusion in nickel. The program has the dual aim of obtaining useful diffusion data and of yielding insight into the factors governing solute diffusion in close-packed metals. The first paper of this series has been published earlier? In both investigations, in agreement with recent results from other laboratories, the activation energies for solute diffusion were found to be close but not identical to that of self-diffusion in the pure solvent in question. In order to obtain valid diffusion data, certain experimental pitfalls recognized only in recent years had to be avoided. Chief among these were the necessity for minimizing short-circuiting diffusion paths such as grain boundaries and the necessity for using low solute concentration gradients. In this series of investigations the following precautions were taken in an attempt to minimize such errors. 1) Samples with large grain sizes, 0.5 to 10 mm, were prepared. 2) The diffusion coefficients were measured at relatively high temperatures, since imperfections such as dislocations play a less important role at such temperatures than at lower temperatures. 3) Alloys containing less than 1 atomic pct were chosen for study. Experimental Work Materials—A diffusion couple technique was employed in the experimental investigation. Briefly, this technique consisted of the following. A diffusion couple was fabricated by placing a flat face of a cylindrically shaped alloy disk against a similar face of a pure nickel disk, and a bond was formed at an intermediate temperature under pressure. The diffusion couple thus fabricated was subjected to a diffusion anneal at higher temperatures for a measured period of time and then sectioned perpendicular to the direction of diffusion. After analyzing the sections for solute concentration the diffusion coefficient was determined from a probability, plot of concentration vs distance from the diffusion interface. Vacuum melted Mond nickel was used in the experimental program. The chemical analysis of this nickel is listed in Table I. Alloys used were prepared

Jan 1, 1958

By A. M. Lovelace

Introduction One area of engineering utilization of materials in which the requirements are especially rigorous and demanding is that of aerospace systems, including aircraft, helicopters, missiles, and space satellites. Materials used in these systems must reliably perform many critical functions in a broad range of adverse environments. Some of the most critical functions are performed by polymeric nonmetallic materials such as elastomers (rubber), coatings, fibrous materials, and reinforced plastics. These types of polymeric materials have some common characteristics that make them attractive to aerospace system designers: light weight, corrosion resistance, and relative ease and low cost of processing and fabrication. Each type also has its own special characteristics that enable it to perform certain required functions better than other competing materials can (Table 1). The desirable properties of polymeric materials, which in some applications make them the only practical candidates, are partly offset by their principal limitation, which is degradation by exposure to high temperature. [ ]

Jan 1, 1971

By A. C. Fieldner

The usual analytical determinations made in analyzing coal are comprised in the proximate and ultimate analysis and the determination of calorific value. The proximate analysis includes determinations of moisture, volatile matter, fixed carbon and ash; the ultimate analysis determinations of carbon, hydrogen, oxygen, nitrogen, sulfur and ash. The proximate analysis is an empirical process, and the results, obtained, especially for volatile matter and fixed carbon, are materially influenced by the method of conducting the determinations. This fact must be kept in mind in comparing coal analyses from different laboratories for classification purposes. Unless these laboratories have followed the same standard methods, differences due to variations in the analytical methods may, in some cases, be large enough to change the classification of the coal. It is unfortunate that the determinations of volatile matter and fixed carbon, which are most used in coal classification, are the two that are subject to the greatest variations. Moisture comes next in the scale of variation. The ultimate analysis is less influenced by method, since it comprises the determination of definite chemical elements. However, even the ultimate analysis is subject to errors, due to inorganic carbon from carbonates and to inorganic hydrogen from water. For these reasons it is evident that the Committee on Coal Classification must be informed on the evolution of methods of coal analysis in America and the average differences in analytical results that may be expected from variations in methods. The committee should be informed also on which methods should be accepted as standard for classifying coal and on the magnitude of the differences in results that may be expected from duplicate samples of the same coal sent to different laboratories for analysis by the same standard methods. It is the purpose of the present paper to provide this information. The subject will be discussed under the following main heads:

Jan 1, 1930

By H. A. Wheeler

THAT lead and zinc deposits are the result of prolonged, slow deposition is the idea of most students of ore deposits, -and in many cases, where the ore-bearing solutions have been very weak or the precipitating conditions have been very feeble, the ore accumulations have undoubtedly taken a long period of time. As these two vital, conditions have been subject to great variations in the different mining camps, the following example is highly interesting in showing that deposition can be very rapid under favorable conditions, geologically speaking, and also extremely recent. In fact, the writer is inclined to regard most, if not all, of the Mississippi Valley deposits of lead and zinc as probably being very young, at least not older than Tertiary, if not Quarternary, in age. The extensive Joplin lead and zinc district, in southwestern Missouri, which is about 60 years old and has numerous mines that were abandoned from 1 to 50 years ago, shows that the lead and zinc today are in an active condition of solution and redeposition, although these two metals occur in the predominant form of sulfides. The mine waters from the older and more or less abandoned portions of the district are frequently so acid, mainly from the oxidation of associated pyrite, as to necessitate the use of wooden pipes and pumps. The first boom in the Oklahoma zinc fields, which is the southwestern extension of the Joplin district, occurred when ore was accidentally struck in drilling a water well. Among the mines then opened up was the Mission mine, at Lincolnville, Ottawa County, Okla. This mine was opened' in 1903 in lean "sheet ground," or a flat blanket formation of chert carrying disseminated zinc blende, or "jack," and galena. The ore-body was very free from iron pyrites and the concentrates were very high grade, the "mineral," or lead concentrates, assayed 80 to 85 per cent. lead and the jack, or sphalerite, assayed 60 to 65 per cent. zinc. The orebody was very shallow, occurring at a depth of 75 to 95 ft. (22 to- 28, in.) and very wet, requiring three or four pumps to handle the water. The

Jan 2, 1920

By T. A. Rickard

The province of Otago consists, roughly speaking, of the southern half of the South Island* of New Zealand. On three sides it is washed by the Pacific Ocean and on the north it abuts against Westland and Canterbury. It covers an area of over 20,000 square miles, and for the most part has an extremely broken surface; the narrow plains of the sea-board are bounded by the rounded foothills which in turn are overlooked by range after range of the snowy summits whose varied beauty has made the island known as the Switzerland of the southern hemisphere. The gold-fields are confined to the quartzose schists which, in a broad band, 70 to 75 miles wide, cross the district, extending in a northwesterly direction from the shore of the western ocean into the northern provinces. These quartzose schists are the characteristic rocks of Otago, and to their curious structure are due the interesting differences exhibited by the mining districts in the modes of occurrence of the gold. These rocks, which are almost unbroken over their full extent, have been divided by the Provincial Geologist, F. W. Hutton, into two series of beds, named respectively the Wanaka and Kakanui formations. The only reason given for this division is the desire " to divide such an enormous thickness of rocks in order that the map might display somewhat of the geological structure of the district." As Hutton and others have pointed out, there is in fact no dividing line. The changes noticeable in the ascending series of schists are very gradual, and are due to the slowly decreasing effects of metamorphism. Hutton estimates the thickness of the Wanaka series at as much as 50,000 feet, and the

Jan 1, 1893

By C. E. Agnew

THE Eastern district, composed of New Jersey and eastern Pennsylvania, with its native ores, was the cradle of the iron industry of the United States The district attained and held the leadership in production of pig iron for over 100 years, from pre-Revolutionary days to approximately 1875 The first shipment of Lake hematite ore was made in 1853 It was a small shipment, transported by a sailing vessel and a canal barge, but it was the beginning of the end of the supremacy of the Eastern district, although at that time the ore was supposed to be too rich to be successfully smelted with the block coal then in use at western furnaces The iron made from the first shipment of Lake ore was worked into nails by the Sharon Iron Co , at Sharon, Pa The writer's great-grandfather, David Agnew, and his brother, John P Agnew, owners and operators of the Sharpsville furnace, Sharpsville, Pa , worked the shipment through a furnace Because of this, the writer feels some satisfaction in having been one of a group that solved the problem of making profitable an operation using Eastern district ores exclusively With the development of Lake mines, and the production and use of coke, the Middle West district gradually assumed the position of leadership in production, because, even though the ores were transported 1000 miles by water and rail, its cost figure on pig iron was better than that of the eastern producer whose furnace was next to his mine Such a cost figure was possible because the ore was naturally rich in iron and reduced easily It was possible to carry a heavy burden on the furnace, which resulted in large tonnage and low coke per ton of iron This paper is in no sense a technical one The purpose is to show that with the proper physical preparation of the Eastern magnetites they will reduce as easily as the Lake hematites, and because of the high iron concentration give the Eastern producer just as much advantage as formally he was at a disadvantage in comparison with the Middle West producer

Jan 1, 1938

By AIME AIME

FOUR separate groups of conveyors are installed in the Morenci Reduction Works as follows: (1) Ore-handling conveyors from the primary crushing plant to the coarse ore bin, from the coarse-ore bin to the secondary crushing plant, and from the secondary crushing plant to the ore bin in the concentrator plant. (2) Conveyors in the mill section of the concentrator plant. (3) Conveyors handling concentrate from the filter plant to the bedding plant, and from this plant to the smelter. (4) Conveyors handling flux and custom ore in the smelter crushing plant and to the bin at the bedding plant.

Jan 1, 1942

By L. G. Carpenter, D. E. Garrett

Probably the largest single tungsten deposit in the U. S. is one that has yet to produce any tungsten; it is not even listed in tables showing U. S. reserves. This deposit is at Searles Lake, Calif., where the brine contains about 70 ppm WO,. Small though the concentration is, the amount of brine in the lake is so great that it is estimated at 170 million lb of WO3 (8.5 million units), equaling the total of all other known reserves in the U. S. This dry lake is located in the basin formed by the Argus and Slate ranges in the northeastern corner of the Mojave Desert (Fig. 1). It consists of a massive salt body some 35 sq miles in extent, varying in thickness from 0 to 120 ft and containing more than 3 billion tons of salt. A central section of about 8 sq miles is exposed salt; the remaining area is overlain by mud. Except for the exposed sodium chloride (10 to 15 ft thick) the body consists of a very complex and heterogenous mixture of soluble crystals, containing at least eight major phases. It is only about 53 pct solid, the voids being occupied by a dense brine which is the raw material for two chemical companies operating in the valley. The deposit is believed to be made up of salts present in the runoff waters from the last two ice stages. Searles Lakes was the third in a chain of five lakes that received waters from the Owens Valley drainage of the Sierra Nevada Mts. After leaving Owens Lake the waters could flood in succession into the Indian Wells, Searles, Panamint, and Death valleys (Fig. 2). During the first two ice stages of the Pleistocene Epoch most of the waters eventually arrived at Death Valley; consequently the lower 3300 ft of Searles Valley contain only mud

Jan 1, 1960

By Jay A. Carpenter

This paper deals with only one step in the treatment of ore at the West End mill; not because the other steps are repetitions of practice in other mills, but because in this particular step there is in use the Trent agitator: This device, although it has apparently failed in many mills, is here giving excellent service and has proved to be well adapted for making a thorough replacement of pregnant solution with a minimum amount of barren solution. The strong and weak points of this agitator, its present simple construction, and its use as a thickener for agitator or battery pulp are features of interest; but perhaps the point of greatest interest to the metallurgist in this day of continuous decantation is its use in a series of tanks for slime treatment by the replacement method. The agitating department of the West End mill consists of six redwood tanks, 24 ft. in diameter, 18 ft. high, each equipped with a Trent agitator, a centrifugal pump, and a motor. The pulp is transferred by a pump from the top of a flat-bottomed tank to a set of arms and nozzles in the bottom of the tank, at just sufficient pressure to cause the arms to revolve. The streams from the many nozzles keep the bottom of the tank clean, and these streams, coupled with the effect of the revolving mechanism and the ascending current, keep the pulp in constant motion and of constant gravity. These agitating tanks hold 90 tons of dry slime and 202 tons of solution with a 1.24 pulp, our ore having a specific gravity of 2.7. This capacity is about 10 per cent. in excess of the standard 15 by 45 ft. Pachuca tank. The tanks are connected in one series for continuous agitation, the pulp for each agitator being drawn by its pump through a branch suction from near the top of the preceding tank and delivered to the bottom of the tank by the agitator arms along with the regular pulp of that agitator. This method works automatically, since the flow through the branch suction varies directly with the difference in head of the two tanks. The chance for new pulp to pass out quickly is, therefore, much less than in many other systems of continuous agitation, since the new

Jan 1, 1916

By A. E. Belton

The individual projections for large mines in the Pittsburgh coal seam in northern West Virginia are discussed with emphasis on roof control and ventilation requirements. All four mines use continuous miners with panel belts and rail for main line haulage. Both development and retreat-type mining are covered. There are a variety of mining projections being used currently in northern West Virginia. To discuss each would be impossible, so an arbitrary cross section has been selected in an attempt to indicate a fair degree of representation. Four mines, hereinafter referred to as Mines A, B, C and Dl will be discussed separately. The greater part of northern West Virginia coal production is mined from the Pittsburgh seam. This is the seam worked by all the mines discussed here. Although the coal bed outcrops at the eastern and southernmost points, these mines are all working in a depth ranging from 400 to 1400 ft below the surface. Some steep gracles have been encountered but are only considered local in nature; the overall average dip of the seam is 1 1/2 % northwest. In each of the operations the particular mining scheme used has proved advantageous, since they have been designed to satisfy particular equipment and/or physical condition requirements. So regardless whether such projections utilize a partial or full recovery principle, the productivity performances appear better than average. MINE A Full retreat is the basic mining approach for mine A, although current mining is primarily in the entry-driving stages to expand territory in preparation for pillar work. Only one section unit now on retreat. The average clean coal production at this mine is 7000 tons per day. Initially, a ripper-type miner was used for development at this mine. But with a rather weak roof overlying the coal bed and the greater horizontal span left at the top by a ripper machine, roof control became a critical problem. Even though roof bolts were used concurrently in the mining cycle for initial support, the majority of the roof in these entries

Jan 1, 1962

By A. T. Peters

DURING an investigation concerning the use of large nozzles for pouring of low-carbon rimming steels, the practical details of which were reported elsewhere, it was noticed that increases of nozzle sizes were generally followed by improvements of slab surface quality. It is the purpose of this note to present the data available and some tentative opinions about this phenomenon. The problem of correlating pouring rates with the metallurgical performance of steels is complicated by several factors. The two most important are; 1) Variations of the steel pouring rate throughout a pour, these being due to the nozzle erosion, which enlarges the bore area, and the dropping ferrostatic pressure in the ladle. The pouring rate is lowest towards the end of a heat when the ladle is nearly empty. 2) Variations in the ingot pouring time due to the different ingot weights poured. Consequently, the use of the average pouring rate of a heat may not be exact, but in large-scale production it is not practical to treat ingots separately according to their pouring rates. The variations of ingot weights and sizes may be overcome by considering the rate of rise of steel in the mold. Hence, the average rate of filling of molds throughout the pour of a heat, inches per second, will be used in this note. Every ingot rolled at Inland is rated at the blooming mills prior to hot machine scarfing as being good, fair, or poor for cracks, scabs, and checking. The latter term refers to the network of breaks or lines associated with overheating or burning in the soaking pits. It is also known that thin-skinned steel is prone to show this defect if the subsurface blowholes are exposed during reheating or rolling. The experiences with the surface quality of slabs rolled from ingots poured at different rates are presented in Fig. 1. The data represent nearly 11,000 ingots. It appears that all three types of defects are in-

Jan 1, 1960

By Arthur Tauber, Horst Kedesdy

FERRITES are sintered metallic oxides of the spinel structure type1 and belong to the class of soft ferromagnetic materials. Similar to a ceramic, they can be formed and fired to a dense body, exhibiting a high electrical volume resistivity ranging from 102to 107 ohm-cm as compared with 10-6 ohm-cm for some of the metallic magnetic materials. This high resistivity, with resulting low eddy current losses, finds special application at high frequencies. The dispersive susceptibility of ferrites at microwave frequencies has also led to many applications in this field. Ferrites are used in low frequency applications where high resistivity with high permeability is desirable. During the last few years ferrites exhibiting rectangular hysteresis loops have been developed for computer and magnetic memory systems. The general formula for ferrites is MeFe2O4 where Me is a divalent metal ion such as Ni, Zn, Mg, Mn, Cu, Cd, and Fe. Only two of these ferrites are nonferromagnetic, namely, those with Zn and Cd. Solid solutions can be formed between different ferrites, and it is of interest to note that solid solutions of a ferromagnetic ferrite with a nonferromagnetic ferrite yield much better magnetic materials than the basic ferrite body. In general, it can be said that the solid solution formation between ferrites has widened the field of ferrite synthesis and has led to methods of preparing materials with a large variety of magnetic properties. During the last two decades the synthesis of ferromagnetic oxides has been the object of extensive research, but commercial production has been started only within the last ten years. Along with more fundamental studies, there remains the never- ending task of developing ways to realize the optimum characteristics of materials in large-scale production. Ordinarily, to produce a ferrite material it is necessary for the constituent oxides to be mixed intimately, pressed, and then fired at temperatures above 1000°C. Ferrite Synthesis: Formation of a basic ferrite by solid state reaction from Fe2O3 and a monoxide such as NiO, under normal atmospheric conditions, is governed by a progressive diffusion of cations between adjacent particles of the constituents. Firing temperature, furnace atmosphere, and cooling can vary the magnetic properties, however. If, for example, a dioxide, a sesquioxide, or an oxide of the Me3O4 type is substituted for the monoxide, the reaction mechanism becomes more complex and extremely dependent on atmospheric conditions and firing cycles. For this reason reproduction often

Jan 1, 1958

By E. A. Anderson

IN another paper1 the writer has shown that the low permissible maximum fiber stress in a loaded zinc sheet demands a much closer support spacing than is used for steel. The limiting fiber stress in 13-gage (0.032 in.) sheets having a 1-in. depth of corrugation was found to be about 5000 lb. per sq. in. on a 37-in. span under a load of 40 lb. per sq. ft. Corrugated steel sheets are commonly laid with spans varying from 48 to 60 in. In order to increase the span in 13-gage zinc to 54 in. (a common spacing) the metal must be capable of withstanding, under long-continued loading, a maximum fiber stress of about 10,000 lb. per sq. in. This is known to be impossible with unalloyed zinc. In this paper the writer describes a series of experiments leading up to the development of an alloy capable of safely sustaining this fiber stress. The effect of alloying on the slow creep of zinc was studied by means of static tensile tests, accurate determinations of apparent elastic limits and finally by means of loading tests on full-size roof sections. Two industrial buildings roofed with alloyed zinc sheets on spans involving fiber stresses in excess of 10,000 lb. per sq. in. have been under observation for over two years without signs of sagging.

Jan 1, 1929

By A. Y. Bethune, W. G. Woolf

THE hydrometallurgy of special high-grade zinc as practiced by the Sullivan Mining Co. at its electrolytic zinc plant, Kellogg, Idaho, involves an important filtration step immediately following the leaching process. By means of the filtration the heavy zinc sulphate solution is separated from the residual products which remain after the zinc calcine has been dissolved in the sulphuric acid electrolyte. Because this plant uses the so-called high-acid, high-density process' for the production of First, the strength of the electrolyte (270g H,SO, per liter) results in a saturated zinc sulphate solution, having a specific gravity of 1.510 to 1.540, which must be kept warm during filtration because of its property of "seeding out" small crystals if allowed to drop much below 60°C. Second, the action of the "high" acid on zinc calcine under the temperature conditions of the leach (80" to 102 "C), although favorable to good zinc extraction, causes a considerable quantity of iron to be dissolved (8 to 18. g per liter) along with variable quantities of alumina and silica, depending on the grade and type of original zinc concentrates roasted. These three, iron, alumina, and silica, are almost completely precipitated during the neutralization of the leach (only a few. milligrams per liter of each remain in solution), so that the resulting pulp, instead of being a granular, sand-like product having a particle-size distribution dependent on the fineness of the zinc calcines leached, is in reality a slimy, chemical precipitate whose filtration characteristics constantly change depending on the amounts of iron silica, and other impurities, which are dissolved and reprecipi-tated. Third, the combination of supersaturated solution of high specific gravity plus a dense, semi-gelatinous residue creates a difficult washing problem requiring a positive displacement wash to liberate the zinc sulphate entrapped in the pulp. In a closed-cycle hydrometallurgical operation, such as practiced in this plant, the extent of washing is determined by the volum,e limitations imposed on the intermediate wash waters by the amount of "fresh" (or process) water which may be added. The volume of fresh water used for makeup purposes is limited to the amount which is lost during the closed cycle by evaporation in the leach, sulphate content of the calcines leached, moisture content of the residue, and spillage. The Burt filter as modified and improved by the Sullivan Mining Co. has successfully met and overcome these difficulties under a variety of zinc plant operating conditions since 1928. It might have many interesting applications to metallurgical fields other than that of electrolytic zinc, and its possible usefulness to hydrometallurgists in general warrants its description and discussion. The Burt filter is so named from its inventor who originated it in Mexico for pulp filtration in the cyanide process for gold and silver ores. While retaining the basic principle of Burt's earlier revolving pressure-type filter with internal filtration media, a number of modifications and improvements have been made in Sullivan Mining Co.'s installation. The Burt filter may be classified as a batch-type pressure filter in contradistinction to either the conventional vacuum-type filter, which depends on atmospheric pressure to force solution through a cloth medium, or to the filter-press, which employs whatever pressure is imparted by the pump delivering the liquid being filtered. The Burt consists essentially of a hollow steel cylinder about 40 ft long, 5 ft in diameter, resting horizontally, and capable of rotation about its long axis. It is supported on one end by a hollow trunnion and near the other end by a riding-ring and roller combination. The cylinder is lined with filter units each fastened against the inside of the shell and parallel to the long axis so as to form a hollow cavity into which pulp may be charged. A specific amount of pulp is admitted to the filter and a unique valving arrangement prevents the loss of pulp while air pressure forces the solution through a canvas medium to the discharge port of each filter unit. The residue is left on the surface of the canvas inside the cavity. The remainder of the filter cycle is concerned with washing the residue free of zinc sulphate, discharging it from the Burt, and preparing the filter for the next charge. A more detailed description of Burt filter construction, a typical filter cycle, and its operating characteristics when employed on material encountered in this plant will be given in that order. Description of the Filter: Fig. 1 shows a side elevation view of a filter with riveted shell construction. Since this drawing was made shells have been fabricated by welding, instead of riveting, with complete success. Shells are lagged on the outside to retain heat. Fig. 1 shows a side elevation and plan view of a Burt filter in operating position. The 1/2-in. steel shells are lined with 3/16-in. copper sheet as protection against the corrosive action of the solution (containing about 500 mg Cu per liter) on iron, and the copper is given a thin protective coating of plastic-base paint. Fig. 2 is a view from the discharge end of the filter, with head removed, before filter units are fastened to the periphery. It shows

Jan 1, 1951

By W. G. Woolf, A. Y. Bethune

THE hydrometallurgy of special high-grade zinc as practiced by the Sullivan Mining Co. at its electrolytic zinc plant, Kellogg, Idaho, involves an important filtration step immediately following the leaching process. By means of the filtration the heavy zinc sulphate solution is separated from the residual products which remain after the zinc calcine has been dissolved in the sulphuric acid electrolyte. Because this plant uses the so-called high-acid, high-density process' for the production of First, the strength of the electrolyte (270g H,SO, per liter) results in a saturated zinc sulphate solution, having a specific gravity of 1.510 to 1.540, which must be kept warm during filtration because of its property of "seeding out" small crystals if allowed to drop much below 60°C. Second, the action of the "high" acid on zinc calcine under the temperature conditions of the leach (80" to 102 "C), although favorable to good zinc extraction, causes a considerable quantity of iron to be dissolved (8 to 18. g per liter) along with variable quantities of alumina and silica, depending on the grade and type of original zinc concentrates roasted. These three, iron, alumina, and silica, are almost completely precipitated during the neutralization of the leach (only a few. milligrams per liter of each remain in solution), so that the resulting pulp, instead of being a granular, sand-like product having a particle-size distribution dependent on the fineness of the zinc calcines leached, is in reality a slimy, chemical precipitate whose filtration characteristics constantly change depending on the amounts of iron silica, and other impurities, which are dissolved and reprecipi-tated. Third, the combination of supersaturated solution of high specific gravity plus a dense, semi-gelatinous residue creates a difficult washing problem requiring a positive displacement wash to liberate the zinc sulphate entrapped in the pulp. In a closed-cycle hydrometallurgical operation, such as practiced in this plant, the extent of washing is determined by the volum,e limitations imposed on the intermediate wash waters by the amount of "fresh" (or process) water which may be added. The volume of fresh water used for makeup purposes is limited to the amount which is lost during the closed cycle by evaporation in the leach, sulphate content of the calcines leached, moisture content of the residue, and spillage. The Burt filter as modified and improved by the Sullivan Mining Co. has successfully met and overcome these difficulties under a variety of zinc plant operating conditions since 1928. It might have many interesting applications to metallurgical fields other than that of electrolytic zinc, and its possible usefulness to hydrometallurgists in general warrants its description and discussion. The Burt filter is so named from its inventor who originated it in Mexico for pulp filtration in the cyanide process for gold and silver ores. While retaining the basic principle of Burt's earlier revolving pressure-type filter with internal filtration media, a number of modifications and improvements have been made in Sullivan Mining Co.'s installation. The Burt filter may be classified as a batch-type pressure filter in contradistinction to either the conventional vacuum-type filter, which depends on atmospheric pressure to force solution through a cloth medium, or to the filter-press, which employs whatever pressure is imparted by the pump delivering the liquid being filtered. The Burt consists essentially of a hollow steel cylinder about 40 ft long, 5 ft in diameter, resting horizontally, and capable of rotation about its long axis. It is supported on one end by a hollow trunnion and near the other end by a riding-ring and roller combination. The cylinder is lined with filter units each fastened against the inside of the shell and parallel to the long axis so as to form a hollow cavity into which pulp may be charged. A specific amount of pulp is admitted to the filter and a unique valving arrangement prevents the loss of pulp while air pressure forces the solution through a canvas medium to the discharge port of each filter unit. The residue is left on the surface of the canvas inside the cavity. The remainder of the filter cycle is concerned with washing the residue free of zinc sulphate, discharging it from the Burt, and preparing the filter for the next charge. A more detailed description of Burt filter construction, a typical filter cycle, and its operating characteristics when employed on material encountered in this plant will be given in that order. Description of the Filter: Fig. 1 shows a side elevation view of a filter with riveted shell construction. Since this drawing was made shells have been fabricated by welding, instead of riveting, with complete success. Shells are lagged on the outside to retain heat. Fig. 1 shows a side elevation and plan view of a Burt filter in operating position. The 1/2-in. steel shells are lined with 3/16-in. copper sheet as protection against the corrosive action of the solution (containing about 500 mg Cu per liter) on iron, and the copper is given a thin protective coating of plastic-base paint. Fig. 2 is a view from the discharge end of the filter, with head removed, before filter units are fastened to the periphery. It shows

Jan 1, 1951