Search Documents

By H. H. Kellogg, T. R. Ingraham

Three anhydrous zinc sulfates have been identified. They are: ZnSO,(a), stable below 1007°K; ZnS04(/3), stable above 1007OK; and ZnO.ZZnSO,. The decomposition pressure of each sulfate has been measured and the following relations calculated from the results: The measured data have been combined with the known themzodynamic properties of ZnS, ZnO, Zn, SO,, and SO, to yield univariant and bivariant phase diagrams for the system Zn-S-0. The application of these diagrams to problems of roasting zinc concentrates is discussed. PRESENT knowledge of the equilibrium chemistry of the system Zn-S:O, so essential to scientific control of zinc-blende roasting, is deficient in several respects. A basic sulfate of zinc has been reported by many investigators, but its composition is in doubt and its thermodynamic properties have not been measured. Our scanty knowledge of the properties of the normal sulfate at roasting temperatures is based on old and inexact studies. A crystal transformation in the normal sulfate, involving a sizable heat effect, has been noted by several investigators but has never been quantified. The studies reported herein were designed to fill these gaps in knowledge and to make possible a reasonably complete thermodynamic description of the system Zn-S-0 at roasting temperatures. The results make possible a far more exact understanding of zinc roasting chemistry than was hitherto possible. EXPERIMENTAL The principal experimental technique employed was the measurement of the total gas pressure developed from decomposition of either ZnSO, or ZnO2ZnS0, in a closed system. The apparatus employed was essentially the same as that described by Warner and lngrahaml and Flengas and tngraham.' The unusual feature is a flexible Pyrex bellows used to separate the reaction gas mixture (S03, SOz, and 02) from the mercury in the manometer and thus prevent corrosion of the mercury by SO3. The bellows operates without evidence of hysteresis and, barring accidents, may be used for several months. The response of the bellows varies from manometer to manometer, but is generally of the order of 0.6-cm displacement for a l-cm change in pressure. The response for all manometers has been linear over the range 0 to 1 atm. To prevent condensation and polymerization of sulfur trioxide, the bellows-manometer was maintained at 100.0" * 0.5" by a circulating bath of silicone oil. The connecting tubing between the manometer and the furnace was maintained at 100.0" * 0.2"* also, with a stirred air bath. The open end of the manometer was connected with a chamber which was maintained at a known pressure. The pressure could be varied so that readings of the height of the mercury column, measured with a cathetometer, could be made with both rising and falling mercury column. By using the average of the readings, any error due to sticking of the mercury column was minimized. The sample was placed in a 2-in.-long platinum boat formed into the shape of a half-cylinder. The sample was prepared as a fine powder and pressed against the inner wall of the platinum boat. A silica thermocouple well, covered with a platinum sleeve, was placed lengthwise along the center of the boat. The temperature of the sample was read on a calibrated Pt-10 pct Rh theirnocouple. The temperature profile of the furnace was constant within ± 0.2 C over the length of furnace occupied by the sample. The horizontal furnace used to contain the sample and the quartz reaction tube was electrically heated, with the control thermocouple placed 1/4 in. from the windings. A Brown Pyro-O-Vane temperature controller with a 3-sec response time was used to maintain the furnace temperature. Before beginning a run, the apparatus, including the bellows manometer, was thoroughly washed in sib with acid and distilled water to remove any

Jan 1, 1963

By Mark R. Lamb

THE various methods of treating pulp in air-agitation tanks offer problems for experiment and study which are fascinating as well as practical. The usual method heretofore has been to fill each tank in turn, agitate the mixture the required period and then discharge the treated pulp into a storage-tank, from which it. is drawn to the filter as required. A later method is to run the pulp from the tube-mill, classifier, thickener, or settler into the first of a set of tanks, and thence continuously or in series through the remaining tanks, finally drawing off the pulp to a continuous filter, or to a pulp-storage tank if the filter is of the intermittent type. It is this method which I propose to discuss here in a preliminary way, with the idea of going exhaustively into the examination of the results of a series of experiments in a later paper. It may be of interest to note that the design of a cyanide-plant has recently been completed in which the estimated cost of the agitation-tanks, storage-tanks, and pumps was 30 per cent higher for the charge-agitation arrangement than for the series plan. The first question in studying the series method is, "What is the actual period of treatment undergone by the pulp?? One first supposes that by chance some of the pulp may get through with little or no treatment, while other portions may stay in the tanks a needlessly long period. The former is not probable or even possible, and the latter is, practically, true to only a limited extent. The greater the number of tanks the greater is the percentage of chance that all the pulp will be treated equally. Without going into the mathematical analysis of the problem (which is of little value, since it is based on problematical premises), its important terms may be clearly grasped by thinking of, or " visualizing," the conditions when,

Jan 1, 1910

By H. Linder, W. H. Dennen

The graphitic carbon content of soils may be used to detect and delimit subsurface graphitic zones. Spectrographic measurement of carbon in C horizon soils from several areas in the northeastern United States shows good correlation with known graphitic bodies. Bodies of graphite and sulfides are readily located by electromagnetic prospecting methods, but these methods cannot generally discriminate between them. Usual practice, therefore, requires follow-up work on electrically anomalous areas by trenching, drilling, or soil sampling in order to determine the mineralogical nature of the conductor. The efficiency and cost of such follow-up is consequently an important factor in prospecting. The presence of buried sulfide deposits is often reflected in concentrations of metals in the superincumbent soil. Simple chemical tests for such metal concentrations have been developed and applied with considerable success. Bodies of graphite or mixtures of graphite and sulfides are, however, very common and a means whereby buried graphite could be detected by soil testing should provide valuable additional information in the search for ore sulfide and graphite deposits. Graphite is a notably stable substance and should persist in soil above graphite-rich horizons. Microscopic examination of soil samples high in carbon, however, failed to reveal any recognizable graphite fragments indicating a grain size in the clay range. Presumably such small particles would have some mobility in a soil by a translocation mechanism similar to that proposed for the movement of clay particles in a soil profile. Experimental data supports this idea since the boundary between background and anomalous soils carbon values is quite sharp, but the anomalous zone is slightly broader than the graphitic source rock. A simple spectrochemical technique for the determination of carbon in geological materials has been described by Dennen,1 and may be directly applied to soils. A modification of this technique which employs an arcing chamber through which nitrogen is passed is recommended to decrease contributions from atmospheric carbon dioxide. Tests indicate that soils over graphitic zones may be strongly enriched in carbon. The spectrochemical determination of carbon depends upon the formation of the cyanogen molecule (CN) from carbon in a sample and atmospheric nitrogen, under the high temperatures associated with a dc arc. Samples for analysis are dried, lumps broken, and screened. A small portion of the -100 mesh fraction is packed into a copper electrode and excited as the cathode of a dc arc. The band spectra of cyanogen are recorded photographically and the density of the bandhead CN 3883A is measured. The limit of detection of the method is about 0.01 pct C and its coefficient of variation is about 15 pct. Soils, of course, contain carbon in other forms than graphite, and the amount of interference from such sources was examined. The C horizon of several soils from Massachusetts, Maine, and Pennsylvania were found to have a carbon content of 0.3 to 0.5 pct by weight. This content is chiefly due to the presence of carbonates and vegetable matter in the sample and may be readily eliminated, or at least

Jan 1, 1961

By A. L. Engel

IN the treatment of complex ores by flotation, one of the most important steps is conditioning the feed. Conditioning primarily consists of the addition, in the grinding circuit, of an alkaline reagent, for example sodium carbonate, which neutralizes any acidity of ore and mill water, counteracts the effect of 'harmful soluble salts, disperses colloids, and provides the necessary alkalinity for the best metallurgical results. The several minerals of the ore should be put in such condition that they may be floated or rejected as desired, through the action of further reagents thereafter used.

Jan 1, 1932

By L. E. Young

GERMANY'S recent collapse and the occupation by the Allies of the coal fields of the Ruhr, the Saar, Silesia, Poland, and Czechoslovakia have focused attention on the postwar coal problems of Europe. American coal operators are interested deeply in what is happening in Britain, particularly in the discussion of plans to rehabilitate and reorganize the entire British coal mining industry, as such reorganization will probably determine the place Britain will occupy in the European coal markets for the next few decades. The continuing decline of British out-ut per man-shift, particularly during wartime, has resulted in a most serious effort to determine whether this unfortunate trend is due to the physical condition of the coal seams, poor management, poor engineering and planning, inadequate use of power and machinery, or failure of labor to co-operate with management.

Jan 1, 1945

By G. F. Loughlin

Nearly 55 years have elapsed since the U. S. Geological Survey was organized. During this period the mineral industries have grown from infancy or early childhood to well developed maturity, and some mining industries appear to be declining. Decline in mining is even more conspicuous in certain districts, or even states, than in any mining industry as a whole, and discoveries or developments of important new districts have been very few in recent years. Our reserves of most metals and nonmetals are adequate for many years of normal production, subject to changes in rate of exploitation that may be caused by foreign competition and by changes in technology and market conditions; but the declining production of many districts and the scarcity of important new discoveries to compensate for them is cause for some apprehension. It is likely that future production will depend to a considerable extent on deep exploration and on the thorough examination of places in and adjoining existing districts where significant outcrops are lacking and only apparently insignificant geologic features offer encouraging clues—more so than on the discovery of entirely new districts. Even the possible discovery of new districts, which have escaped the intensive search by the nontechnical prospector, must be dependent on geologic information. There is therefore no need for argument as to the value of geology to the mining industry; and the need of continuing to advance the science. The U. S. Geological Survey's past contributions to mining geology, as expressed in its official reports and other publications, are recognized by Ransome in his historical review of mining geology in the Lindgren volume.' These contributions have helped to form the basis of modern mining geology, which has grown rapidly in the last 25 years. This growth has witnessed the organization and maintenance of geologic staffs by mining companies in several districts, and their detailed work, together with the fact that nearly all of the larger mining districts have

Jan 1, 1935

The General Electric Co., in cooperation with the Montana School of Mines and under a research grant from the Anaconda Co., is presently experimenting on a new non-explosive method of breaking rock with radio-frequency electrical power. The method is known as electrothermal forcing. It must be understood that present equipment has not been designed to perform primary blasting functions. Its conceived use will be restricted to small pieces of rock too large to pass through a chute or grizzly. However, even this use is still far in the future. Experiments to date have been limited mostly to rock smaller than 18 in.

Jan 11, 1961

By K. C. Mills, E. T. Turkdogan

A number of investigators1 6 have noted the presence of a liquid miscibility gap in the Fe-Sn binary system. However, the first attempt to measure the

Jan 1, 1964

By Grafton Thrasher

For the proper discussion of this subject it is necessary to incorporate in this paper the substance of part of an article published by rite in Metallurgical and Chemical Engineering for January, 1915. CAST-IRON TEST PLUG, SHOWING LOW MOTTLED AND MOTTLED FRACTURES. Several years ago, while I was thief chemist for a malleable-iron company, it occurred to me that the mere regulation of silicon was not sufficient to produce the desired degree of chill. But only after repeatedly encountering this fact in befit open-hearth and air-furnace, as well as cupola metal, was I led to regard variation in the total carbon as the principal cause of disturbance; and I resolved to determine the total carbon as well as the sill on ill every heat, and by a carefully prepared test piece to gauge the approximate degree of chill. The test piece selected was a round plug, 2 in. in diameter and 12 in. long, cast on end

Jan 10, 1915

By A. B. Kinzel

SILICON and its metallurgical uses have been the subject of speculation since the earliest days of modern civilization. The early philosophers, Theophrastus and Pliny, believed that silica was a special form of ice, an opinion that was not seriously challenged until the seventeenth century. The first comprehensive view of the nature of silica was advanced by Lavoisier in 1787. He assumed silica to be an oxide of an unknown metal. In 1808 Berzelius produced ferrosilicon by heating silica, iron and charcoal. Probably the first produc¬tion of crystallized silicon was in 1854 when H. St. C. Deville accidentally produced the material while electrolyzing a double chloride of aluminum and sodium containing siliceous impurities. It is not strange that the early investigators should have given so much attention to silica and silicon, because of the great natural abundance of the former. Although silicon does not exist in the elemental state in nature, it has been estimated that the lithosphere contains approximately 60 per cent silica; quartz and rock crystal are found in practically every part of the world.

Jan 1, 1933

By Arthur L. Hall

The purpose of this symposium is to challenge industry to better air classification, and as a first step toward fulfillment, to spotlight three fairly recent, aerodynamically designed, highly efficient air classifiers. This discussion does not intend to imply that present practice is bad. Actually, when present air separators are used for the jobs for which they were originally designed, they give high production and uniform operation, with a minimum of maintenance. The customers of nonmetallic mineral pigment producers, however, are making increasing demands for finer products, such as 99.9 pct -20µ, which appears to be beyond the economic capabilities of standard air separators industrially used over the last 10 to 30 years. Here is an actual example. A 10-ft diam pebble mill is in closed circuit with a conventional 12-ft diam centrifugal air separator, grinding 20-mesh wollastonite to a series of fine grades up to 99.97 pct - U.S. No. 325 mesh (44µ). Fig. 1 shows variations in fineness of mill discharge (or air separator feed), recycle for regrinding (or air separator tails), and product as measured by a wet rotating sieve test. For example, when the mill is turning out a product 80 pct -325, the mill discharge or separator feed is 30 pct -325, and the coarse tailings or recycle is only 5 pct -325. Hence 25 pct of the 30 pct available is accepted as product. This is efficient separation, and the ratio of recycle to feed is only about 2: 1. How- ever, to make a product testing 99.97 pct -325 the separator feed is 62 pct -325 and the coarse tailing 60 pct -325. In this case the recycle ratio is about 13: 1 and the economic limit to produce fineness has been substantially reached with this given equipment and process arrangement.

Jan 10, 1957

By Sadtler, C. B.

IT is generally assumed that in most metals and alloys a given tensile stress produces a given deformation irrespective of the length of time during which the stress is applied. This assumption is justified in most of the important engineering applications of metallic materials; however, in the case of some metals and alloys used or tested at temperatures over or slightly under that at which recrystallization can occur the assumption is not warranted.1 This paper deals with the variations of deformation produced by a constant tensile stress acting for varied lengths of time in the special case of thin aluminum alloy sheet of the duralumin type, which had been subjected to different thermal and mechanical treatments. The material investigated was in the form of a sheet approximately 0.002 in. thick, which had been cold-rolled from a thickness of 0.020 in. It has been found that at a sufficiently high constant tension such material deforms continuously with the elapse of time and that the rate at which this deformation occurs is greatly influenced by the previous thermal and mechanical treatments.

Jan 1, 1927

A discussion of the paper by Mr. Campbell, which was read by title at the Lake Superior meeting, but first presented at the New York meeting of the Iron and Steel Institute, October, 1904 (see p. 772). These papers are here published onder a mutual agreement between the Councils of the two Institutes, and will also be found in the Journal of the Iron and Steel Institute for the year 1901, vol. ii. Mr. William R. Webster, Philadelphia, Pa., said: We are under great obligation to Mr. Campbell for his exhaustive investigation, and the results he has put before us to-day. They are the most conlplete series of tests that have ever been made, where all the conditions of rolling, etc., were kept uniform. In discussing Mr. Campbell's first investigations, I claimed first, that the method of least squares, then used, would of necessity only gire the average value of any element, and that if the effect of any element was greater in the presence of high carbon than with low carbon this would not be shown by the method of least squares. Secondly, that the effect of manga nese should be considered on acid steel as well as on basic steel, instead of ignoring all the eff'ect of that element when it was below 0.60 per cent., as was then recommended by Mr. Campbell. I am pleased to note that the results of his present investigation confirm my views on these points. In presenting the results of his first investigation, Mr. Campbell referred to my investigation of 1893-94, and took exception to the value of phosphorus varying (depending on the amount of carbon present) from 800 to 1,500 lb. for each 0.01 per cent. He claimed that one might just as well consider the effect of phosphorus as being constant, and of carbon varying. I refer to this, as he now has introduced very similar conditions in his present tables, in that he gives variable values for manganese (depending on the amount of carbon present) for both acid and basic' steels. Can we now say, with more certainty than formerly, which element should be considered as haviup a constant effect ? There is one other point that I took up in my former discus-

Jan 1, 1905

By AIME AIME

THE fall meeting of the Petroleum Division, held at Tulsa, Okla., on Oct. 11 to 14, devoted two days to technical sessions and two to field excursions. A representative attendance of 250 to 300 engineers and operating officials engaged in oil production marked the sessions and paid close attention throughout to a notable series of highly technical papers. Restricted as the program was to consideration of production problems only, the time proved too short for discussion or even the presentation of the 20 papers submitted. Much informing and pertinent discussion none the less took place, and the sentiment was general to the effect that the meeting was one of the best ever held by the Division. The meetings were held in the auditorium of the Municipal building and local arrangements were well looked after by the Mid-Continent Section of the Institute and the Oil and Gas Association. The combination of the three organizations served to bring together engineers and operators most usefully. F. Julius Fohs, chairman of the Division, presided at the sessions on Monday. Tuesday morning John M. Lovejoy of the local section took over this responsibility in the absence of T. E. Swigart, who was detained in California. The afternoon session was presided over by A. G. Heggam of the Oil and Gas Association and the Tuesday evening banquet by W. C. Franklin of the same organization.

Jan 1, 1926

By H. J. LONGMORE

MORE improvements have probably been made in the diamond-drill field in the past decade than were accomplished in the entire prior period since diamond drilling was discovered in 1864 by a French engineer named Leschot. True, machines were improved, and new accessories were adopted from time to time up to 1929, but no radical changes were made. The basic principle instituted during the early years of the industry were still in use in 1929. At that time, practically the only diamonds used were "black diamonds" or "carbon." These came from Brazil through a rather round- about route, and by the time they got to the drilling trade their cost was excessive-$175 per carat and even higher at the peak. Perhaps because of this. or perhaps because of increased competition, the industry sought ways to reduce expenses even in the face of constantly increased labor costs due to higher wages and reduction in hours worked. The solution seemed to rest in two things-use of a cheaper cutting medium to replace the carbon diamond and the development of new machines to drill faster and thus produce more hole per shift of operation.

Jan 1, 1940

By D. Kuhlmann-Wilsdorf

A new theory of work hardening is developed which rests on only a few simple principles and is applicable to a wide variety of materials and dislocation structures. It explains, qualitatively, the general characteristics of the three-stage shear stress-shear strain curve of fcc metals, as well as the most important features connected with easy glide. The value of, the work-hardening coefficient in stage 11, is derived quantitatively, from first principles, and is shown to be insensitive to many changes in detailed dislocation behavior. The low rate at which energy is stored during mechanical working in stage 11, the dependence of slip line length on stress, and the so-called Cottrell-Stokes law are explained. Although the theory is primarily developed for fcc metals and alloys, it is largely applicable also to some other materiuls, and in particular apparently to poly crystalline simple steels in theh linear range of hardening. FOR pure fcc metals and alloys, after many different pretreatments and under a great variety of testing conditions, the well-known three-stage work-hardening curve is commonly observed. Moreover, the work-hardening coefficient in stage 11, 011, bears an almost constant relationship to G, the modulus of rigidity, such that K = G/Brr" = 300, within a factor of about 2 either way. The very fact that the three-stage curve and the value of K are so very persistent, can hardly be understood except on the assumption that some quite simple phenomena are responsible. In this light all available theories of work hardening must be judged unsatisfactory: Each of them is based on some quite specific dislocation model, while it is known that metals with similar values of K may have widely different dislocation structures, for example, dislocation tangles in the case of pure fcc metals, and piled-up groups of dislocations in a-brasstype alloys. Thus, while a particular theory might conceivably represent a special case with a reasonable degree of accuracy, it cannot possibly have illuminated the underlying principle. Another severe criticism applying to the presently most widely discussed theories is that they employ empirical or even quite unexplained parameters in order to arrive at a numerical value of K. This indicates that some vital aspect of the work-hardening process has remained unexplained. In the present paper, a new theory of work-hardening is developed which does not suffer from the above shortcomings. It is derived from first principles, and is founded on the realization that the underlying causes for the three-stage work-harden- ing curve and for the persistence of the numerical value of O,, must be few and simple. As a first step it is shown herein that the experimental oklservations on "easy glide" can be explained on the assumption that in this stage dislocations multiply, beginning in a number of restricted area:;, and from there penetrate into crystal regions still substantially free of glide dislocations until a quasi-uniform dislocation distribution has been established. During "easy glide", the resistance to the movement of the foremost dislocations, advancing into still largely a dislocation-free regions, is believed to control the flow stress. This resistance is determined by various factors, among them the reaction of the dislocations against bowing-out into loops, which is due to their line tension. Without such bowing-out no dislocation multiplication would occur, but the corresponding contribution to the flow stress stays practically constant all through stage I. According to the present theory, stage TI begins as soon as there are no more areas left into which newly formed dislocations have not yet penetrated, i.e., as soon :is a quasi-uniform dislocation density has been attaned. Regardless of how, in detail, the dislocations should happen to be arranged at the end of "easy glide", whether in pileups or tangles, on one glide system or on several, the stress necessary to overcome the line tension of the segments must now increase, because the dislocation density increiises while the average free dislocation length decreases. It is argued that all other contributions to the flow stress stay at about the same level as in stage I, and that the said increase in the stress necessary to bow out dislocation segments into loops is responsible for the major part of work hardening in stage 11. Stage TII of the stress-strain curve is explained by largely follouing the ideas of Seeger and his co-workers; however, it is pointed out that the start of stage m may on occasion indicate the onset of "conservative climb" instead of cross slip. Indirect evidence indicates that linear work hardening persists even under the profuse action of cross slip, but at a lower rate. Only when, in addition to cross slip, climb operates extensively, does the work-hardening rat,. drop sharply, ultimately down to zero. BRIEF SURVEY OF EXPERIMENTAL EVIDENCE The stress-strain curve of crystals of many different substances are qualitatively similar. No significant permanent plastic deformation takes place below the so-called "critical resolved shear stress". As the applied stress is raised beyond this level. yielding occurs with little or no work hardening and

Jan 1, 1962

By AIME AIME

THAT the copper industry is in serious straits is admitted. So are the lead and zinc industries, and both lead and zinc are tariff protected. Conditions in the Western lead, zinc and silver mining districts are desperate. These are illustrated by the present disastrously low prices of these metals compared with the levels of two and three years ago and by the comparative rates of metal production and the present activity of the western mining camps. The January production of copper was 32.2 per cent of the 1929 average rate, of steel was 32.3 per cent of the 1929 average, while January production of pig iron was only 27.6 per cent of the monthly average of 1929. The copper industry is only one of many industries that are suffering in this tragic depression. It has been exceedingly prosperous and will be prosperous again when business recovers. Its difficulties are not unique and it does not deserve the tariff equivalent of a dole. The burden of subsidizing through an effective tax or tariff the minority group of high-cost mines would be a heavy one on the consuming public of the United States. On the basis of 1929 consumption figures, an effective 5c. tariff would result in an increased copper bill to the country of over $109,000,000, of which the electric manufacturers would contribute $26,000,000, the telephone and telegraph companies $16,000,000, and the automobile manufacturers $14,000,000. And of this total bill, only $33,000,000 would go to those who are urging a tariff and the balance of $76,000,000 would be paid to those who do not admit either its necessity or usefulness under present conditions.

Jan 1, 1932

Institute of Metals Division Ferrous and Nonferrous Physical Metallurgy Established as a Division April 26, 1918 (Bylaws published In the 1944 TRANSACTIONS Volume of the Division) A A SMITH, JR, Chairman E A ANDERSON, Past-Chairman F N RHINES, Senior Vice-Chairman W A DEAN, Vice-Chairman H A MALONEY, Treasurer ERNEST KIRKENDALL, Secretary 29 West 39th Street, New York 18, N Y Executive Committee R M BRICK 2 W A JOHNSON 1 H I DIXON 2 E W PALMER 1 M GENSAMER 2 J H SCAFF 3 J D HANAWALT 1 J D SULLIVAN 3

Jan 1, 1952

THE Lehigh Valley Section is planning with a num-ber of other organizations a three-day conference, April 25, 26 and 27, with field visits to cement, slate and steel plants in the vicinity of Easton, Pa. W. B. Plank is chairman and D. Knickerbocker Boyd is sec-retary. Headquarters will be at Hotel Easton. Wednesday' will be cement day. In the forenoon A. S. T. M. Committee D-16 will meet and after luncheon the delegates will visit the Martin Creek plants of the Alpha Portland Cement Co. An evening dinner and general session on cement is being arranged. Thursday morning will be devoted to a technical ses-sion on slate, and the breaking of ground for the new John Markel mining building at Lafayette College. After luncheon various slate quarries will be inspected, the visitors being guests of the companies. In the eve-ning there will be a conference dinner at Hotel Easton with a number of distinguished visitors. Friday will be given over to steel and will include a visit to Lehigh University, an inspection of the plant of the Bethlehem Steel Corp., and a luncheon as guests of the latter.

Jan 3, 1928

By A. L. Holley

The members of the society are doubtless aware that the production of American Bessemer steel works is constantly increasing; that the same converters and machinery are doing more work every year. This enlarged output is due to various causes, chiefly the following: 1st. Better organization—better knowledge on the part of both managers and men, of the plant and the process; of the way to economize the more exhausting labor, and of the arrangement of the details of labor and operations so that they shall not conflict; also, more pluck—a greater willingness to take risks, or, more properly, such an intimate knowledge of the nature and capacities of the refractory linings in various stages of disrepair, and the probable be- . havior of the fluid metal at various stages of its treatment, that the precise nature of the risk may be better known, so that the works may be crowded to their full capacity. In the early practice, after getting four or five consecutive heats in a day, the men preferred to " let well enough alone," and to devote the remaining time to preparation for another turn. Now, thirty, and sometimes forty heats are regularly made during the twenty-four hours, day after day, without the frequent occurrence and without the fear of breakdowns or " messes," as the spilling of steel charges was graphically named in Sheffield. 2d. Although no new refractory materials have been developed, improved means of preparing such as we have, and of imbedding