Search Documents

By M. W. Dumais, E. P. Abrahamson

In a paper by Abrahamson and Alexander concerning a series of correlations between electronic structure and property changes, it was hypothesized that each solute atom in a dilute solution had a characteristic volume of solvent atoms over which some form of electronic interaction occurred. From this description it is possible to picture the solute atoms as occurring in an ordered array for the most efficient arrangement. A recent review article2 has shown that some form of anomaly exists for a whole series of properties when dilute additions of tungsten are made to iron, of. Fig. 1. Any mechanism to fit one property must also be amenable to mechanisms for the other properties. The possibility of some structural change in this region appears to offer the best hope. The system chosen for investigation was the iron tungsten system. Zone-refined iron with zone-leveled tungsten additions were supplied by Materials Research Corp. as 3/8-in.-diam bars. Transmission electron microscopy was used to study the structure. One-quarter inch specimens of each alloy were cold-rolled to 10-mil sheets, cleaned, punched to electron-microscope specimen-holder size, and annealed in vacuum for 2 hr at 800°C and 2 hr at 700°C followed by a furnace cool. The specimens were attached to a platinum wire and the specimen edge and wire were painted prior to thinning in a solution of 10 pct perchloric acid in glacial acetic acid. It was believed that if ordering were present due to electronic interactions the polishing procedure chosen would provide a simultaneous combination of chemical attack and electropolishing to exhibit the ordered structure. The chemical attack would be expected to penetrate those areas equidistant from the tungsten atoms, while the electropolishing would serve to "plane off" the volumes where the chemical attack had taken place. If one of the ordered tungsten planes were parallel to the specimen face at the edge of the thinned hole, a plate or micalike structure would be expected. A typical result of this polishing is shown in Fig. 2. Here a series of plates can be seen lying one upon the other. In several other specimens the plates parallel to the electron beam have been observed, behaving like slices of bread in a loaf. These edge views coupled with moire patterns indicate that the minimum plate thickness is 37 to 42A. This is equivalent to a concentration of 455 at. ppm of W if a simple cubic superlat-tice exists, or one tungsten atom every twelve iron atoms on the ordered plane. It was further noted that the base iron exhibited no signs of platelike structure. As the concentrations increased above 100 at. ppm W the amount of plate material increased. Among the specimens investigated was that shown

Jan 1, 1967

By Gary E. Parish

TABLE OF CONTENTS Contents I. Introduction II. Purpose of the Paper III. Historical Perspective A. Existing Sources B. New Sources (NSPS) C. Hazardous Pollutants (NESHAPS) D. Enforcement/Judicial Review 1. Title I Enforcement 2. Title III Enforcement 3. Information Gathering E. Summary IV. The Clean Air Act Amendments of 1977 (1977 Act) A. SIP-Related Provisions 1. Section 107(d) - Geographic Boundaries 2. Section 108 - Air Quality Criteria 3. Section 109 – NAAQS 4. Section 110 – SIPs 5. Section 122 and Sections 402 and 403 of P.L 95-95 – Unregulated Pollutants 6. Emission Offsets – Interpretive Ruling (I.R.) B. PSD Provisions - Part C. 1. Regulations Under the 1970 Act 2. The 1977 Act 3. Regulations Under the 1977 Act C. Visibility Protection - Part C, Subpart 2 D. Non-Attainment Provisions - Part D E. Monitoring and Modeling F. NSPS G. NESHAPS H. Enforcement/Judicial Review 1. Title I 2. Economic Enforcement 3. Title III Enforcement/Judicial Review (a) Section 304 (b) Section 307 4. Summary V. Special Problems and Opportunities for the Uranium Industry A. End Use B. Transportation C. Milling/Processing D. Extraction E. Exploration/Discovery F. General VI. Conclusions Appendix A Footnotes

Jan 1, 1979

By Henry N. McCarl, John J. Dran

The academic community and the larger and more sophisticated mining companies have largely rejected the older mineral valuation methods such as the Hoskold and Morkill concepts and replaced them with "discounted cash flow" (DCF) techniques. The relevancy and usefulness of the older methods have been questioned primarily on the basis of their underlying assumptions that mining companies do not have numerous alternative investments and must use sinking funds deposited at market or "safe" rates of return to recover the purchase price of mineral reserves. The ability to reinvest in numerous (often nonmining) alternative business ventures, the changing purchasing power of the dollar, corporate income and other taxes, depreciation and depletion allowances, and modern financial management practice all militate against the continued use of the older valuation methods, especially for the larger mining companies. Small mining companies and individuals still use these methods largely out of habit and familiarity. The Hoskold Mineral Reserve Valuation Method The Hoskold method was developed prior to the evolution of modern accounting practices and before the days of the corporate income tax. At the time of its development, annual earnings of the firm were represented by the difference between cash revenues and cash expenses and were not subject to taxation by the government. Thus, earnings at that time were equivalent to what is today known as cash flow.

Jan 7, 1974

By A. C. Rand

The invention to be described in this paper is the work of Frederic A. Halsey, Engineer for the Rand Drill Company, of New York, and its use mill abridge the notable wastefulness of power of the striking rock-drill, and, at the same time, increase its capacity for work. That the older type of rock-drill is wasteful in power, is generally admitted; the cause being the use of steam* without expansion, arid the "cushion" of the blow, by the incoming steam upon the lower † end of the piston before the cutting tool strikes the rock.

Jan 1, 1885

By E. S. Wheeler

THE rapid increase in the use of monel metal and malleable nickel in the form of sheet, rod and tube has resulted in a similar increase in the demand for these metals in the form of castings. These castings range in size from small valves and pipe fittings weighing a few ounces to large centrifugal pumps, gate valves and marine propellers, some of the latter weighing as much as 24,000 lb. A group of such castings is shown in Fig. 1. A large nickel agitator is shown in Fig. 2. FIG. 1.-A GROUP OF MONEL METAL AND NICKEL CASTINGS. Monel metal castings are widely used in accessories for steam power plants and in a variety of chemical plant. equipment where the corrosion resistance, high strength and toughness characteristic of this metal render it particularly valuable. Nickel castings find extensive use in the construction of corrosion resistant apparatus, and are often used in conjunction with wrought nickel sheet and tube in the fabrication of equipment for handling a variety of chemical and food products, particularly dairy products. In response to this demand for castings, numerous foundries have undertaken the production of castings of these metals and have met with varying degrees of success.

Jan 1, 1930

By Edward S. Cook

For several years past, dating particularly from the days of serious "ore-dirt" complications at the Warwick furnace, I have been desirous of providing some safe, quick and easy method of relieving the tuyeres of slag, when the cinder- and iron-notches are chilled through loss of heat in the clucible or when, from dropping or jumping of stock, the molten slag is forcibly driven into the bellyand leg-pipes. Various methods were proposed, but objections of one kind or another always presented themselves, and the subject was postponed to a more convenient season. In the summer of 1887, while running on anthracite alone, 1 found the various expedients in use to be so utterly valueless, that the importance of a practicable tuyere slagging-valve impressed me more forcibly than ever. The holes left in the cast-iron jacket at one side of the bottom of the water-blocks were found to be of no value whatever. The swinging or hinged cap on the elbow of the belly-pipe, while convenient to permit the removal of lag after the belly-pipe was partially or wholly filled, could not be adapted to discharge the slag before solidifying, except at great risk to the men and loss of time just when the constant running of the engine and the keeping of blast on the furnace was of the utmost importance. By removing keys from the caps and holding them in place with props, the slag could be discharged through the tuyeres and belly-pipes, with the engine running, by knocking the props away at a given signal. This method is extremely hazardous to life and limb, and I have always hesitated to make use of it. When the furnace is in such condition as to require the adoption of some method of the kind, the stoppage of the engine, cooling the blast and the contents of the crucible, always aggravates the trouble. When the caps are blown open and the slag is discharged by removal of the props, it is necessary to stop the engine to replace them. An hour or more will elapse before this can be done, as the slag must be partly removed before the tuyeres can be approached by ordinary mortals, and the caps handled and fastened in place again. Any movement of the stock is liable to burn the workman, as he stands, securing the cap in front or at one side of the open belly-pipe.

Jan 1, 1889

By M. D. Everell

A study has been made of the relationships between grinding selection functions and physical properties of rocks, particularly the failure loads of irregular particles and the compressive and tensile strengths of large regular specimens. The rocks used were limestones of various structures and impurity contents, a carbonatite, and a high-purity crystallized calcite. The selection functions were obtained from carefully performed grinding experiments on selected narrow size ranges in various grinding machines-a laboratory batch ball mill, a Hard grove grindability machine, and a mill of the type suggested by Yang, Mempel, and Fuerstenau. The specific rates of breakage during milling and the failure loads of irregular specimens correlated well for the rocks studied. The testing of irregular particles is suggested as a means of predicting the behavior of commercial mills.

Jan 1, 1973

By Eugene S. Perry

The only outstanding development in Montana oil or gas fields during 1935 was the extension of the Cut Bank oil and gas field 7 miles southward. This field is now about 20 miles long and 3 to 8 miles wide, with 218 producing oil wells and 39 producing gas wells. Average daily production of the oil field during December, 1935, was about 6700 bbl.; total production for the year 1935 was approximately 2,020,770 barrels. The Cut Bank field in northern Montana is in a flat to rolling glaciated area used mainly for grazing purposes. Oil and gas occurs in sandstones and shaly sandstones in the Kootenai (Dakota) formation of Lower Cretaceous age at depths ranging from 2700 to 3000 ft. Prominent anticlinal or domal structure is not present, but small plunging anticlines occur locally. Strata dip westward from 75 to 200 ft. per mile. The field lies on the western flank of the Sweetgrass arch, a broad gentle upwarp over 150 miles long. Localization of oil and gas appears to be due either to pinching or lensing out of the sandstone beds, or else silting of the sandstones with clay minerals so that porosity becomes low. Within the field offset wells show marked variation in initial production, which suggests that differences in porosity of sandstone is the controlling factor. The gas-producing portion of the field is entirely updip (east) from the oil-producing portion, and the producing horizons are the same. Initial production of oil wells ranged from about 50 to about 200 bbl. per day, and initial open flow of gas wells ranged from about one million to about 37 million cubic feet per day, with an average of 11 million cubic feet. Initial gas pressures were slightly greater than 700 lb. per sq. in. Oil is brought to the surface by pumping. Both rotary and standard churn-drilling equipment are used. In the remaining 14 oil and gas fields but little new activity took place other than the drilling of offset wells and wells in proven territory. Continuation of "acid treatment" of wells in the Kevin and Pondera oil fields led to reconditioning of many old wells and the drilling of a number of new wells within these fields. Acid treatment of the oil-bearing horizon, which is the dolomitized and silicified Madison limestone of Mississippian age, has proved quite satisfactory, and some "bone dry"

Jan 1, 1936

By Eugene S. Perry

The only outstanding development in Montana oil or gas fields during 1935 was the extension of the Cut Bank oil and gas field 7 miles southward. This field is now about 20 miles long and 3 to 8 miles wide, with 218 producing oil wells and 39 producing gas wells. Average daily production of the oil field during December, 1935, was about 6700 bbl.; total production for the year 1935 was approximately 2,020,770 barrels. The Cut Bank field in northern Montana is in a flat to rolling glaciated area used mainly for grazing purposes. Oil and gas occurs in sandstones and shaly sandstones in the Kootenai (Dakota) formation of Lower Cretaceous age at depths ranging from 2700 to 3000 ft. Prominent anticlinal or domal structure is not present, but small plunging anticlines occur locally. Strata dip westward from 75 to 200 ft. per mile. The field lies on the western flank of the Sweetgrass arch, a broad gentle upwarp over 150 miles long. Localization of oil and gas appears to be due either to pinching or lensing out of the sandstone beds, or else silting of the sandstones with clay minerals so that porosity becomes low. Within the field offset wells show marked variation in initial production, which suggests that differences in porosity of sandstone is the controlling factor. The gas-producing portion of the field is entirely updip (east) from the oil-producing portion, and the producing horizons are the same. Initial production of oil wells ranged from about 50 to about 200 bbl. per day, and initial open flow of gas wells ranged from about one million to about 37 million cubic feet per day, with an average of 11 million cubic feet. Initial gas pressures were slightly greater than 700 lb. per sq. in. Oil is brought to the surface by pumping. Both rotary and standard churn-drilling equipment are used. In the remaining 14 oil and gas fields but little new activity took place other than the drilling of offset wells and wells in proven territory. Continuation of "acid treatment" of wells in the Kevin and Pondera oil fields led to reconditioning of many old wells and the drilling of a number of new wells within these fields. Acid treatment of the oil-bearing horizon, which is the dolomitized and silicified Madison limestone of Mississippian age, has proved quite satisfactory, and some "bone dry"

Jan 1, 1936

By V. Miller

Highly variable milling procedures within a geologically complex porphyry copper deposit owned by Kennecott Corp. in Nevada made it necessary to estimate copper recovery and concentrate grade in areas where actual test data was lacking. Estimation was made by first determining the relationships between desired metallurgical properties and the ore's petrology-copper mineral type, rock type, and copper grade. This relationship was then combined with previously estimated rock type, mineral type, and copper grade data in the mineral block model to predict milling properties.

Jan 1, 1985

By R. P. Marshall, L. P. Costas

The solid solubility of lithium in aluminum was determined by two independent techniques, electrical resistivity and microhardness, and the results are in close agreement. The solubility limits X-ray diffraction studies of the intermetallic compound LiAl indicate that its composition is nearly independent of temperature when in equilibrium with the terminal solid solution of aluminum. THE investigation of the aluminum-rich portion of the aluminum-lithium system at the Savannah River Laboratory was prompted by the observation that over-aged alloys consistently differed from the equilibrium states predicted by the latest published diagrams. Chemical analyses of these alloys showed their impurity contents to be quite low; therefore, the results obtained should have very nearly coincided with true equilibrium. A survey of the literature disclosed that previous studies had been made with metallographicig or electrical resistivity methods,4'5 but that agreement between results and technique was poor as evidenced in Fig. 1, which also includes the present results for comparison. The discrepancies have been attributed to impurities,3 and this is undoubtedly true in the early work.1'4'5 The latest Studies,''~ conducted with starting materials of higher purity, employed metallographic analysis, a technique that is quite sensitive to local homogeneity and depends strongly on subjective interpretation. In the present work the problem of defining solubility limits was approached in two ways. The first measured a physical property, electrical resistivity, at the equilibrium temperature. The second, a micro-hardness characterization of a diffusion zone, is a room temperature evaluation of a mechanical property under conditions removed from equilibrium. A close correlation between two such basically different approaches would strongly justify confidence in the results. I) MEASUREMENT OF SOLUBILITY OF LITHIUM IN ALUMINUM BY ELECTRICAL RESISTIVITY Experimental Procedure. Alloys for electrical resistivity measurements were made by melting and

Jan 1, 1962

By Albert S. Trube

Increasing emphasis is being placed on the necessity for obtaining reasonably accurate estimates of the physical properties of reservoir fluids well in advance of more accurate laboratory data. One such factor is the isothermal coefficient of expansion of an undersaturated hydrocarbon liquid which may be contained in a particular reservoir. This coefficient, or liquid "compressibility", has often been assumed to be relatively insensitive and nearly constant. Although this assumption may be nearly correct in the case of high specific gravity liquids, it cannot apply in the case of medium to low specific gravity liquids. Any treatment of the nature of liquid compressibilities must give consideration to the variable nature of the isothermal expansion coefficient and the fact that it can be both pressure sensitive and temperature sensitive. The isothermal coefficient of expansion, or compressibility, of a substance is defined as -c = 1/V (?V/?p)T......(1) The value of Eq. 1 may be approximated for a finite pressure change by using the well-known relation, c = V1 - V1/Ve (p2-p1), ........(2) in which p1 > p1 and V2 > V2 and V1 + V2/2. The instantaneous compressibility may also be estimated from the slope of a curve on which log V is plotted vs pa. In this instance, it has been shown that c = In V1/V2/p2-p1 ...........(3) Eq. 3 may be used for variable compressibilities by plot-ting V vs p on semi-log paper. In this case, the instan-taneous or point compressibility is c = 2.303 m.......... . (4) in which m is the slope of the curve at a point in log cycles per psi. ISOTHERMAL COMPRESSIBILITY OF UNDERSATURATED LIQUID In the case of gases, the compressibility has been defined by Muskat' and others as Co = 1/p - ?z/z?p ..........(5) This was later generalized through application of the theorem of corresponding states' to co = 1/pr - (?z/z?pr) T8 ........(6) in which c, is defined as the pseudo-reduced compres-sibility and is numerically equal to (c.p,) and the sign is arbitrarily changed for mathematical convenience. Eq. 6 is general and applies to gases and liquids. In the case of liquids, c. = c1,pe, but if Eq. 6 is used, values of z and ?z/?p, must be determined for the liquid in question. The difficulty of obtaining accurate values of ?z/?p,, particularly in the region where T, is approaching 1.00, was pointed out in the previous paper'. This method of approach is unreliable for extension into computations of liquid compressibilities. On the other hand, c, can also be defined as follows: - Cr = 1/Vr (?Vr/?pr) Tr ......(7) and from which, Cr = 1/pr (?pr/?pr) Tr .....(8) In accordance with the theorem of corresponding states, Vr = V/Vr, p, = p/pr and pr = p/pr. Ref. 2 pro-vides an excellent source of reduced density, reduced pressure and reduced temperature data for a wide variety of fluids. For the purpose of this investigation, the set of fluids2 having ze = 0.27 was chosen because it in-cludes most of the heavier hydrocarbons usually found in those complex mixtures loosely defined as "reservoir oils". Data on undersaturated liquids in Ref. 2 were rearranged to conform with Eq. 8. To simplify the computation of cr, the isothermal p, data were plotted vs the log of pr, in which case for any straight line or tangent cr = 1/M pr pr .....(9)

Jan 1, 1958

By E. Luttgen

The substance referred to in the title is the artificially prepared basic carbonate of magnesia, a compound of the carbonate with the hydroxide. It is the "block-magnesia " of commerce, the magnesia alba of the pharmacist. Its composition, though somewhat indefinite, may usually be expressed by the formula : 4MgCO3,Mg(OH)2, 5H2O; it is found to vary slightly with the details of the method of preparation. This substance has been employed recently with much reported success, as a non-conductor of heat. It is moulded to form coverings suitable for steam-pipes and their fittings and sectional jackets for boilers and cylinders; it is furnished also in forms suitable for lining refrigerators, walls and roofs of buildings, fire-proof safes, etc. It was with a view of ascertaining the efficiency of this material as a non-conductor, or, rather, its relative efficiency among the various non-conducting materials in use, that the writer made the experiments about to be described. A block of magnesium carbonate or magnesia alba exhibits some interesting physical qualities. It is a smooth, white, close-grained solid, in outward appearance resembling a block of Paris plaster. It possesses the lightness of cork, the porosity of sponge, and withal a degree of firmness and strength that, in view of its levity, is quite remarkable. To examine more closely the properties of this substance, a number of 1-inch cubes were sawed from the commercial block-carbonate, also some bricks, that is, blocks measuring accurately 2 x 4 x 8 inches, the dimensions of an ordinary brick. The cubes weighed from 2.2 to 2.7 grammes, the bricks weighed 140 to 175 grammes (5 to 6 ounces). The bricks were carefully measured and weighed, and placed in vessels containing distilled water, in which they became gradually submerged, owing to the displacement by water of the air inclosed in the structure of the magnesium carbonate. After twenty-four hours the blocks were removed from the water, dried superficially by contact with filter-paper and weighed. From the increase in weight, the volume of the water absorbed, and consequently that of the air displaced by it, were obtained. For example: a block which when dry weighed 155

Jan 1, 1887

By C. C. Koch, M. L. Picklesimer

PHYSICAL metallurgists interested in the alloying behavior and phase transformations in rare-earth metals and alloys require a strain-free polished and etched surface for both metallographic and X-ray examination. However, the rare earths have presented a problem in this respect since they are difficult to polish free from strain and are very reactive to the atmosphere. Their tendency to oxidize readily even at room temperature necessitates careful preparation and rather elaborate protection if their surface is to be examined for any length of time. The "light" lan-thanides (i .e., atomic numbers less than 63), especially lanthanum and cerium, are particularly bad in this regard; they oxidize very rapidly at room temperature. To eliminate the problem of plastic deformation remaining on the surface after mechanical polishing, electropolishingl and chemical polishing techniques2 have been developed. The electropolishing technique requires the specimen to be immersed in an electrolyte at -77°C and thus obviates a metallographic study of, for example, the fcc —double-hexagonal close-packed (dhcp) transformation in cerium which begins at -10°C. The chemical polishing solution has been used only on several of the "heavy" rare-earth metals. However, a convenient method for protecting the polished and etched surfaces from atmospheric corrosion has not been available. Our interest in the superconducting properties of lanthanum, and in the phase transformations in lanthanum and cerium, has led us to develop a technique for the metallographic preparation of lanthanum and cerium which clearly reveals the microstructure and preserves the etched surface for days. The specimens are chemically polished and anodized. The chemical polishing is performed at room temperature, the anodic oxide film provides the required protection from the atmosphere, and colors produced in the film provide a simple positive technique for phase identification. Lanthanum and cerium metal ingots obtained from Johnson Matthey and Co., Ltd., were remelted to suitable shapes and heat-treated to produce various microstructures. The samples were placed in epoxy mounts and, after a small hole was drilled in the back of the mount for electrical contact, were ground on silicon carbide

Jan 1, 1968

By B. F. Buie

For over 200 years meerschaum has been a significant item of trade between the Near East and countries to the west. Best-known for its use in making smoking pipes and cigar and cigarette holders, it is also used in making a variety of decorative and ornamental items. It is easily carved, and is given an attractive, lustrous finish by rubbing. No published specifications are known, but compact form, purity, uniform whiteness or light color, and uniform, porous texture appear to be requisites. Fig. la shows the appearance of a piece of crude meerschaum from Turkey; [Fig. lb a carved item; and Fig. lc, d, and e] show the fibrous and porous texture as revealed by the scanning electron microscope. Neither a major industrial mineral nor a precious stone, meerschaum nevertheless holds a record of long-and continuing-association with art and personal affairs of man. It is also a mineral to which modern methods of exploration and production probably could be profitably applied. An interesting account of the preparation and use of meerschaum in the early part of this century is given by Sterrett (1907). Geology and Mining Mineralogy Meerschaum is recognized now to be the compact variety of sepiolite, the claylike variety of which is one of the minerals included in the chapter on clays. The word "meerschaum," from the German meaning "sea foam," was in earlier times used synonymously with "sepiolite," a word of Greek origin suggestive of the resemblance of the compact variety-then the only variety known-to cuttlefish bone. At one time "meerschaum" was used as the commercial name, and "sepiolite" for the scientific name. However, to think of meerschaum as the name by which sepiolite is known commercially is no longer valid, in view of the recent emergence of the earthy variety as a competitor of bentonite and other clay materials. Present tendency is to restrict the term "meerschaum" to the compact variety, and to use the term "sepiolite" as a more general name to include both the compact and earthy varieties. This is the terminology followed in this publication.

Jan 1, 1975

By C. S. Barrett

IT has been observed that deformation in iron takes place by slip on {110} + {112} + {123} planes1,2 but in silicon ferrite with low deforma-tion temperatures or high silicon contents (exceeding 4 per cent) the authors have found that slip is confined wholly to {110} planes, at least with small amounts of deformation. The purpose of the present inves-tigation was to determine the effect of this alteration of slip mechanism on preferred orientations in cold-rolled and recrystallized strips. Inci-dental observations on the effect of the recrystallization temperature were also made. The numerous determinations of the texture of cold-rolled iron and steel have been in satisfactory agreement as to the principal features of the texture. (with the exception of a few conclusions that apparently have been based on insufficient data). The texture is chiefly one in which [110] directions of the grains lie along tile direction of rolling, with a deviation of a few degrees, and in which the (100) planes lie in the plane of the rolled sheet, with a deviation from this position chiefly about the rolling direc-tion as all axis 3-9. This deviation about the rolling direction as an axis has been measured by different observers and lies between about 45° and 50° or 60° for iron5,6,9 and is usually in the neighborhood of 50° for mild steel6,7,8. The range of this deviation is a function of the percentage of total reduction 8, 10. Post' reported that it decreases with increasing percentage reduction, but apparently he .studied only the surface material, which Gensamer and Mehl7 found to be somewhat differently oriented from the material in the inside of the sheet. McLachlan and Davey10 found that the deviation also decreases with increasing percentage of total reduction for the material in the interior of the sheet and is independent of the percentage of reduction per pass.

Jan 1, 1937

By C. S. Barrett

It has been observed that deformation in iron takes place by slip on (110) + {112) + (123) planesl, 2, but in silicon ferrite with low deformation temperatures or high silicon contents (exceeding 4 per cent) the authors have found that slip is confined wholly to (110) planes, at least with small amounts of deformation. The purpose of the present investigation was to determine the effect of this alteration of slip mechanism on preferred orientations in cold-rolled and recrystallized strips. Incidental observations on the effect of the recrystallization temperature were also made. The numerous determinations of the texture of cold-rolled iron and steel have been in satisfactory agreement as to the principal features of the texture (with the exception of a few conclusions that apparently have been based on insufficient data). The texture is chiefly one in which 11101 directions of the grains lie along the direction of rolling, with a deviation of a few degrees, and in which the (100) planes lie in the plane of the rolled sheet, with a deviation from this position chiefly about the rolling direction as an axis. This deviation about the rolling direction as an axis has been measured by different observers and lies between about 45" and 50" or 60" for iron5, 6, 9 and is usually in the neighborhood of 50" for mild stee16, 7, 8. The range of this deviation is a function of the percentage of total reduction8, 10. Post8 reported that it decreases with increasing percentage reduction, but apparently he studied only the surface material, which Gensamer and Meh17 found to be somewhat differently oriented from the material in the inside of the sheet. McLachlan and Davey10 found that the deviation also decreases with increasing percentage of total reduction for the material in the interior of the sheet and is independent of the percentage of reduction per pass. The deviation about the cross direction as an axis (the direction in the

Jan 1, 1937

Abbey, Robert Graham, District Mgr.. The W. W. Sly Mfg. Co., 50 Church St.. New York, N. Y. '21 Abbott, A. N., Mines Supt., Mazapil Copper Co., Ltd Concepcion del Oro, Zac., Mexico. '28 Abbott, Argyle Campbell, Dev. Dept., E. I. du Pont de Nemours & Co., Wilmington, Del. '29 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg.. Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Elkhorn Div., Consolidation Coal Co., Jenkins, Ky. '16 Abeel, George H., Jr., Cons. Min. Engr Box 427, Santa Monica, Cal. '18 Abel, Albert E., Asst. to Pres., Valley Mould & Iron Corp Hubbard, Ohio. '19 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh. Pa. '28 Abeel, Leo M., Research Engr., Sullivan Concentrator Chapman Camp, B. C., Canada. '31

Jan 1, 1932

By Orville R. Lyons

This paper presents a method whereby the amount of misplaced material and the difficulty of the separation can be used to compare coal cleaning equipment of all types, from effectiveness and capacity standpoints. The correlations presented do not include all types of equipment currently available, but the method can be used to evaluate any make or type of coal cleaning equipment, both old and new. THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,' but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."' Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."' It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913," by the United States Bureau of Mines in 1938,' by Hancock in 1947," and by the national French research agency Cerchar in recent years.' In 1950 Andersone proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or k0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1953

By Orville R. Lyons

This paper presents a method whereby the amount of misplaced material and the difficulty of the separation can be used to compare coal cleaning equipment of all types, from effectiveness and capacity standpoints. The correlations presented do not include all types of equipment currently available, but the method can be used to evaluate any make or type of coal cleaning equipment, both old and new. THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,' but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."' Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."' It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913," by the United States Bureau of Mines in 1938,' by Hancock in 1947," and by the national French research agency Cerchar in recent years.' In 1950 Andersone proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or k0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1953