Search Documents

By S. D. Dahlgren

The plasticity of unalloyed P plutonium was studied by evaluating the strain-rate-hardening exponent, m, in the equation Values of m up to 0.33 and tensile elongations up to 680 pct were obtained for ß plutonium formed directly from the a phase. Casl bars that were cycled and tested had lower flow stresses and higher values for than uncycled bars , hut their total plastic elongations were not as great as expected because of premature failure at voids formed during cycling. Flow stresses were higher and m was lower (m = 0.15) for 9 plutonzutn formed from the y phase. ThE strain-rate-hardening exponent for plastic flow of p plutonium was determined as a function of strain rate, test temperature, and heat-treating history, and it was related to the rather large plastic elongation found previously for some plutonium tensile samples. Gardner and ~ann' obtained tensile elongations of up to 620 pct for P plutonium samples which had been completely transformed from the low-temperature a phase to the P phase before testing. Such a large percentage elongation is unusual for unalloyed metals or single-phase alloys.' The a phase is stable below approximately 112°C and (3 is stable between approximately 112" and 190"c.~ Both phases have mono-clinic structures. A temperature of 160°C is 0.58 of the effective absolute melting point, 475°C) of the p phase. The effective melting point is obtained by considering the enthalpy and entropy changes associated with the higher-temperature phase transformations and it is not the same as the experimental melting point of the highest-temperature allotrope of unalloyed plutonium. Nelson, Bowman, and Bierlein observed a striking difference between the ductility, as well as other mechanical properties, of p plutonium formed from the next higher-temperature phase (y) and the ductility of /3 plutonium formed from the a phase. The total elongation of /3 plutonium formed from the y phase was less than 5 pct. Earlier, the creep rate of 13 plutonium formed from the a phase was shown to be 200 to 500 times faster than the rate for 0 formed from y for the same test temperature and stress.

Jan 1, 1969

By Wilder D. Bancroft

It is eight years since I have been connected actively with metallography, but in this time I have been learning something about colloid chemistry, which may be considered as the chemistry of bubbles, drops, grains, filaments, and films, all things in which at least one dimension is very small or in which the surface is large relatively to the mass. Films, of course, suggest to the metallographist Beilby's amorphous film theory, about which I am going to speak for a while, though probably not in the way you expect. I come to bury Beilby, not to praise him. So far as I can judge from looking over the literature hastily, there are two schools in the United States, those who accept Beilby's theory willingly and those who accept it unwillingly. Hoytl says that: At present there seem to be two schools in metallography, one which has adopted the amorphous-phase theory for the explanation of the effect of cold work, mechanical deformation, etc., and one which is not ready at present to adopt this theory. It seems to me that this theory can at least be used as a convenient means of explaining various facts that are demonstrable in the laboratory but the presence of this amorphous material, through our lack of experimental means, we are unable to prove. That we have failed in this direction should not necessarily hinder us from using a theory as workable as this. Mathewson2 says: I have come reluctantly to believe in the amorphous theory, or some theory admitting a modification of the ordinary crystalline phase so as to permit differential properties with temperature, etc. If Mathewson represents one extreme, with Hoyt perhaps occupying a middle ground, H. M. Howe3 may be cited as one of the enthusiastic supporters of Beilby's amorphous theory. It is, says Howe:

Jan 1, 1923

By Wilder D. Bancroft

It is eight years since I have been connected actively with metallography, but in this time I have been learning something about colloid chemistry, which may be considered as the chemistry of bubbles, drops, grains, filaments, and films, all things in which at least one dimension is very small or in which the surface is large relatively to the mass. Films, of course, suggest to the metallographist Beilby's amorphous film theory, about which I am going to speak for a while, though probably not in the way you expect. I come to bury Beilby, not to praise him. So far as I can judge from looking over the literature hastily, there are two schools in the United States, those who accept Beilby's theory willingly and those who accept it unwillingly. Hoytl says that: At present there seem to be two schools in metallography, one which has adopted the amorphous-phase theory for the explanation of the effect of cold work, mechanical deformation, etc., and one which is not ready at present to adopt this theory. It seems to me that this theory can at least be used as a convenient means of explaining various facts that are demonstrable in the laboratory but the presence of this amorphous material, through our lack of experimental means, we are unable to prove. That we have failed in this direction should not necessarily hinder us from using a theory as workable as this. Mathewson2 says: I have come reluctantly to believe in the amorphous theory, or some theory admitting a modification of the ordinary crystalline phase so as to permit differential properties with temperature, etc. If Mathewson represents one extreme, with Hoyt perhaps occupying a middle ground, H. M. Howe3 may be cited as one of the enthusiastic supporters of Beilby's amorphous theory. It is, says Howe:

Jan 1, 1923

By H. S. Gieser

THE flotation of oxidized silver, ores offers an interesting problem to the operating metallurgist, who has to treat this material. The advances made in the art of selective flotation by the use of newer collectors with accelerating and inhibiting reagents suggests that there should be something to help to decrease tailing losses. For many years there was no working hypothesis, so the subject was approached more or less in the dark, but with the publication of a paper by Taggart, Taylor and Ince1 giving results of flotation tests with many organic compounds and presenting a tentative theory, a better foundation has been laid and henceforth progress should be more rapid. Over a period of one and one-half years there was much experimentation with flotation of oxidized silver ores at El Tigre, Sonora, Mexico. The material coming to the mill was straight sulfide ore in a silicified rhyolite gangue, the ore minerals being sphalerite, galena, pyrite and tetrahedrite. This came largely from the lower levels of the mine. With the approaching exhaustion of these orebodies, attention was turned to oxidized ores left behind during higher prices of silver. Of late oxidized ore has been at times 25 per cent. of mill tonnage. Aerofloat 25, in considerable quantity, together with ethyl xanthate, has been used in the mill. The former raises large quantities of "insoluble" or gangue, which is difficult to reject when the density of the tailing pulp approaches 33 per cent. solids, as it did during periods of water scarcity. The mill tailing at times contained as much as 5 oz. of silver on a 32-oz. mill head.

Jan 1, 1931

By H. S. Bell

IT SEEMS unnecessary to dwell upon the advantages of the modern pipe still as compared with the older type of distillation equipment used by oil refiners. The relatively low installation cost, coupled with remarkable operating efficiencies of pipe stills, precludes the consideration of other types except in rare instances where some peculiarity of product or plant may have an influence. The question of the actual heat required to distil petroleum is quite involved. We have extensive data on the latent heats of the various hydrocarbons under different conditions of pressure. We also have information regarding the specific heats of various oils and the effect of temperature thereon. Because of the complexity of petroleum and of each fraction, it seems impossible to theoretically analyze the partial-pressure effect of the great number of hydrocarbons upon one another during distillation. If a distillation curve and percentage analysis of any crude or product are available, it is possible to construct a curve with ordinates representing per cent. distilled and B. t. u. per pound or per gallon, or other desired unit. To do so the crude is split into fractions, of 5 or 10 per cent. The boiling point and gravity of each fraction being determined, it is possible to evaluate the heat required. As each fraction is removed, the residue must be raised to a higher temperature and latent heat supplied for the successive fraction. As the calculations progress, the latent heats decrease while the specific heats increase. Such a curve is illustrated by Fig. 1 for a typical 39.9 B° North Texas crude.

Jan 1, 1928

By J. Vakili

The objective of this paper is to present a practical method for calculating minimum safety factors of rock slopes with a horizontal layer of weak material. It is demonstrated that the most critical failure surface, in this case, is a bilinear surface composed of a horizontal failure surface inside the weak layer and an inclined surface inside the rock. The model presented in this paper shows that with a good approximation, the change in slope for the bilinear failure surface may occur directly below the slope crest. This assumption simplifies the calculation of safety factors considerably, because the most critical failure surface is located directly, and the trial computations for a number of failure surfaces are not necessary. Special parameters involved in slope stability analyses of highwalls in open-pit mines are discussed and, by an example calculation, the applicability of this method is demonstrated.

Jan 1, 1985

Would you give us a short biographical sketch including your birthplace, education and current activities? I was born Jan. 16, 1920 in Minneapolis, Minnesota, and lived there the first 22 years of my life. I also spent quite a bit of time on a farm about fifty miles north of Minneapolis owned by relatives. During the Depression, we lived off of ten cows and about fifty chickens. I'm a full-blooded Swede all along the line, and I'll be the last one in my family since my wife is not of Swedish descent. I attended Macalester College, a small school in St. Paul, to study for the ministry originally. However I soon realized that I really didn't have the talents for the ministry and I could probably do as much or more in a field where I did have some talent.

Jan 3, 1974

The following discussion occurred on the afternoon of Sept,. 22, 1930, as part of the fall meeting of the Iron and Steel Division at Chicago. About seventy-five men attended this session. C. B. Murray opened the meeting, as follows: C. B. Murray, Cleveland, Ohio.—It is very encouraging to see so many here this afternoon to discuss this important matter of beneficiation. The producers of ore, I am sure, are anxious to furnish the grade of ore that the consumer wants. The consumer sometimes wants that which cannot be economically produced and often the producer cannot understand why the consumer wants certain things. It was to bring together these two interested parties that this meeting was proposed. I was appointed the chairman of the meeting, chiefly because I happened to be the chairman of the Iron Ore Committee of the Institute. I know a little about iron ore but have not perhaps kept up with the times in blast-furnace practice. I am asking Mr. Sweetser, who is well informed from both sides, to take over the meeting and carry on the discussion. R. H. Sweetser, Columbus, Ohio.—We want to have a free discussion between the iron-ore men and the blast-furnace men as to just what we are trying to reach in the beneficiation of iron ores. Many of those present have had a great deal of experience. There are men here from the ranges who have been passing through the experimental stage of beneficiation of iron ores, and there are some who have already gone on to commercial production. We have reached the point where the beneficiation of iron ore is important to the whole iron and steel industry. The connection between iron-ore beneficiation and the cleaning of coal is so close that I think we can profit by working very close to the coal people. Some Aspects of the Iron-ore Situation W. G. Swart, Babbitt, Minn.—I was very much interested in Mr. Richards'* paper on tonnages and the 20-year life. There is one interesting thing about the ore reserves; that is, the irregular distribution of that tonnage. On the Mesabi Range, for example, the United States Steel Corpn. owns between 70 and 75 per cent. of the reserve tonnage. They ship bctween 40 and 50 per cent. of the annual Lake Superior

Jan 1, 1930

By S. C. Robinson

International interest in storage and retrieval of geological data stems from a desire to tap this large and potentially valuable, but little-used resource. The data will be used primarily for development and testing of geological concepts and theory; secondarily as a basis for assessing mineral potential and even individual mineral deposits; thirdly for establishment of world-wide norms averages and standards; and fourthly as a search tool leading to sources of specific data and to repositories of specimens etc. International committee activities are designed to establish acceptable general standards for reference numbering, geographic location, geological terminology, coding etc. ; and to develop progressively the types of data (parameters) that should be recorded in specialized archival files in such fields of world-wide interest as palaeontology, mineral deposits, petrochemistry, stratigraphy, mineralogy, palaeomagnetism, physical geochronology etc. Establishment of world data banks analogous to those in oceanography may come later; for the present we hope to achieve some degree of agreed consistency in national and local data banks throughout the world, and to establish an international index to these banks as first steps in facilitating international exchange. For purposes of this paper, data are defined as facts, reproducibly measured or objectively described.

Jan 1, 1969

By Eugene S. Meieran

The effects of methods of crystal growing, wafer sawing, polishing, routine handling, diffusion, and epitaxial growth on the defects in GaAs are reviewed and studied using reflection and transmission X-ray topographic techniques. In general, it was found that boat-grown crystals exhibited fewer defects than Czochralski crystals, although all crystals showed large numbers of precipitates visible when examined in the electron microscope. Mechanical surface treatments such as sawing and mechanical polishing introduce damage to a depth of about 5 µ, most of which can be removed by suitable chemical or chem-mechanical polishing. In addition, defects can be introduced through routine handling of wafers, for example with metallic tweezers. These defects can be quite severe, and have been observed 20 µ below the wafer surface. Defects can also be introduced through diffusion and epitaxial growth. These defects, which include precipitates, growth pyramids, stacking faults, dislocations, and so forth, can be detrimental to device fabrication. It is shown that wafers or films which appear defect-free optically can contain defects visible in the X-ray topographs. WHILE the use of GaAs in the semiconductor industry has increased very rapidly in the last few years, due mainly to the recent development of many important GaAs devices,1,2 the major limit to the production of commercial quantities of many GaAs devices remains a severe lack of suitable materials technology. This lack is apparent in two critical areas. First, production quantities of high-quality GaAs crystals, reproducibly doped and precipitate-free, simply are not available commercially, although some reasonable quality material is available on a limited first-come, first-serve basis. Second, in comparison to silicon technology, little is known about the effects of processing variables on the defects either present in as-grown GaAs or introduced through processing and handling of wafers. These areas are now receiving some attention from semiconductor device manufacturers, who are studying defects in GaAs in order to better understand how either to prevent their occurrence or to cope with their existence. Most investigations of the defects in GaAs have been made by optical microscopy3-5 or transmission electron microscopy techniques.'-' Recently, however, the imaging techniques of X-ray topography, electron mi-croprobe analysis, and scanning electron microscopy are being applied to the study of GaAs.9-14 In the case of X-ray topography, a one-to-one image is obtained that must be photographically enlarged. In compensa- tion, the defects within entire wafers may be imaged by simple scanning (Lang technique15) if the wafer is reasonably perfect, or by using the scan oscillation technique developed by Schwuttke16 if the wafer is warped or distorted. The purpose of this paper is to both review and extend the general application of X-ray topographic techniques to GaAs. Emphasis will be placed on the effects of growth and process variables on the quality and perfection of both bulk and epitaxial GaAs. Reference to optical or electron microscopy results will be made when useful. Since the effects on defects of a wide variety of processing variables such as crystal growing, sawing, polishing, diffusion, and epitaxial growth will be somewhat superficially reviewed, a fairly extensive bibliography of the most important recent results in these areas is included. However, for completeness, important defects will be illustrated here, although such defects have been previously shown by others. While this paper is concerned with defects rather than with the physics of X-ray scattering, the mechanisms of contrast formation in the topographs will of necessity be briefly mentioned. EXPERIMENTAL GaAs crystals, both boat-grown18 and Czochralski-grown,'8 containing a variety of dopants of various concentrations, were purchased from outside vendors. Wafers were sliced from the crystals using a Hamco ID saw and were mechanically polished using 1 µ diamond paste. Chem-mechanical polishing was done in bromine-methanol as described by Sullivan and Kolb.18 Chemical polishing was done using a modified sulfuric-peroxide solution, 11 parts H2SO4, 1 part 30 pct H2O2, 1 part DI water.5 Zinc diffusion was carried out in a closed tube, using a 10 pct Zn-In source at 825°C for 1 hr. Oxide masking techniques were used to select the area to be diffused. Epitaxial wafers were either purchased or prepared here. All epitaxial runs prepared here were carried out using a Ga-GaAs-AsC13 source in a closed tube at a substrate temperature of 750°C. Wafers were chem-mechanically polished and gas-etched prior to deposition. The X-ray topographs were taken on a Krystallos Lang camera, operating in the transmission scanning geometry (Lang technique15) or in the reflection scanning geometry (modified Berg-Barrett technique20,21). MoKa, radiation was used for all transmission topographs using a Jarrell-Ash 100-µ spot focus. CuKal radiation was used for all reflection topographs using a General Electric CA-7 1-mm spot focus X- ray tube. Topographs were printed from an intermediate contrast inversion film, so the contrast shown in all figures here is the same as that of the original 50-µ-thick emulsion L4 Iiford nuclear plate used to record the topograph.

Jan 1, 1969

By F. S. McNicholas

IN the writer's opinion the term "block caving" has been rather loosely applied to a general principle of mining, and therefore detailed classification of caving methods and draw, together with the characteristics required for each method, will fill a desired need. Selection of caving method should be made only after a study of all governing conditions, such as size of orebody, lateral and vertical extent of ore-body, attitude, treatment demands, possible resultant pressures, and cost and profit comparison of methods. Successful caving methods can be classified under six main headings: (1) Full-protected block caving, (2) semi-protected block caving, (3) unprotected block caving, (4) full-panel caving, (5) half block-panel caving, (6) block-panel caving. The methods and factors governing choice of method are shown in Table I. Full-protected Block Caving Full-protected block caving consists of develop-ing, undercutting, and drawing to exhaustion a block of ore of predetermined size without coordination of mining or draw with adjoining areas. The block is mined and drawn as an independent unit (Fig. 1). Full-protected block caving demands that mining and draw cannot be done against unconsolidated capping in adjoining caved and exhausted blocks. Two sides of block are against solid. Caved capping must be allowed to consolidate for a suitable period, usually not less than one year. Pillars may be left in lieu of consolidated capping (Fig. 2). The advantages of full-protected block, caving are: (1) A definite area is developed, mined, and drawn as a unit so that all work may be completed, the block drawn to exhaustion in the minimum length of time, and the area then abandoned. (? Production is not restrained because of coordina1, on with adjoining areas. (3) Records of draw and caved reserve of ore are good. Upon abanwnment of the block, accountability for production is closed out with no carry-over to adjoining areas. The disadvantages of full-protected block caving are: (1) Side dilution from the draw adjacent to the consolidated capping may be serious, particularly where capping does not consolidate sufficiently in the allotted time. (2) Boundary weakening is needed on the solid sides of the block except in weak rocks. (3) Maximum cantilever and compression effect to aid caving and fragmentation may not be secured since the draw should proceed from the solid to the consolidated capping to minimize side dilution. However, undercutting from the loose (caved capping) to the solid with a slight initial draw in the same manner will develop cantilever effect. (4) A period of at least one year, more is usually desirable, must be allowed for caved capping ,to consolidate before mining the adjoining block, depending upon the characteristics of the capping. (5) Capping may not consolidate sufficiently in the time that can be allowed. Full-protected block caving is indicated where: (1) The ground is weak and heavy and workings

Jan 1, 1952

By Francis H. Brownell

During the 1920's lead consumption in the United States reached the highest average total ever known. For the ten-year period 1921-'30, it was slightly over 600,000 tons per year, or say 50,000 tons per month, and the price averaged 6.81 per lb. But the I930's witnessed a severe drop in the consumption of lead is in other business activities. The average U.S. consumption for the ten-year period 1930-'40 was slightly less than 380,000 tons per year, or under 32,000 per month, with the average price dropping to 1.191c. per lb. The outlook in early 1939 was for a continuation of this average consumption and price a demand of 35,000 to 40,000 tons per month, and a price level of 4 1/2 to 5c. in the United States.

Jan 1, 1941

By C. S. Barrett

The torsional after-effect in polycrystalline cadmium is interrupted by an abnormal twisting when the film is removed by etching. This is accounted for by the pile-up of dislocations beneath anodic or other oxide films during the original twisting, and the relief of the residual stresses from these by elastic and plastic processes during etching. WHEN an iron or zinc wire coated with oxide is plastically twisted and then released, it untwists according to a law of equal increments in equal intervals of log time, but if the oxide is suddenly removed by etching this normal after-effect is interrupted by a transient, and thereafter the untwisting is slower.' Etching may even reverse the strain temporarily. Related effects caused by hydrated oxide films on cadmium in creep tests have been observed by Phillips and Thompson:' definite transient strains caused by the removal of the film from single crystals of cadmium were observed; however, negligible effects were obtained with polycrystalline wires. Pronounced effects of both transient and steady nature were observed by Phillips and Thompson when anodic films 10-4 cm thick were etched off, and weak effects, transient only, occurred with hydrated oxide films 3x10 cm thick such as were formed by standing in water for 10 min. It was estimated that 10.' cm films, formed in water in 1 or 2 min, could be detected in the apparatus of Phillips and Thompson. Since abnormal after-effects were observed by the torsion method equally well with polycrystalline and monocrystalline iron and zinc wires,' it was anticipated that the torsion method would also disclose them in polycrystalline cadmium, in spite of the fact that analogous effects had not been observed in tensile creep tests on polycrystalline zinc by Pickus and Parker3 r on polycrystalline cadmium in tensile studies by Andrade and Randall." Because of its high sensitivity, particularly its sensitivity to surface conditions, the torsion method was thought to merit further study as a method of investigating thin films of various types and the action of various reagents on these films. Materials and Methods Cadmium wires were cold-drawn to a diameter of 0.039 in. from a stock that was determined spectro-scopically to contain 0.05 pct Bi, 0.005 pct Cu, 0.008 pct Pb, and 0.007 pct Si. The wires were cut to about 17/8 in. lengths and were annealed 1 hr in air at 290°C, after which the grain size was such that there were 5 to 7 grains across a diameter. The wires were then mounted as indicated in the insert in Fig. 1, one end being fastened with laboratory wax into a small diameter brass tube and the other end being waxed to a thin glass fiber which supported, on its upper end, a small galvanometer mirror. The wires were waxed with care to avoid straining or annealing, for it was found that the after-effect rate was sensitive to prior cold work in a wire. The assembly was then clamped above a beaker into which the reagent could be poured. The lower end of the wire was held in the hand while the wire was twisted 180"; it was then released immediately. Since precision timing of these manipulations was not attempted, the different wires cannot be compared as to exact rates of untwisting. The length subjected to plastic strain was 15/8 in. The surface coatings studied were those produced by the annealing in air, by anodic treatment of

Jan 1, 1954

By Hugh S. Spence

In the winter of 1941-42, muscovite mica was discovered by a young prospector, Justin Purdy, in the township of Mat-tawan, Nipissing District, Ontario, a few miles north of the small settlement of Eau Claire, which lies on the main Transcontinental Highway (No. 17) between Mattawa and North Bay. Muscovite had been known for many years to occur in the general Mattawa region, and various small efforts at production had previously been made by individuals working scattered deposits in the area. These minor activities, however, had never led to production of any consequence or the discovery of any important mica bodies. The Purdy finds were made in a heavily timbered, mountainous area lying about three miles north of the low-lying settled land along the highway, and in a section not hitherto prospected. The mica taken by Purdy and two partners from surface outcrops proved so remarkable in point of size of trimmed sheets that the find attracted considerable attention, and the area surrounding the three claims taken up by the prospectors was quickly blanket-staked by various interests. Though a number of other mica-bearing pegmatite dikes were found later on these stakings, none proved as rich as those on the original Purdy ground; very little commercial mica was obtained from them and attempts to develop them were short-lived. Purdy and his partners sold their initial production to dealers in Ottawa and Hull, where the Canadian mica industry long has centered. Young Purdy, unfortunately was killed in a motor accident in the early summer of 1942. His father continued mining operations for a few months and produced and sold a considerable amount of mica. In October 1942 the Purdy holdings were acquired by lnspiration Mining and Development Co. of Amos, Quebec, which had been active in staking in the area. This company formed a subsidiary, Purdy Mica Mines, Limited, to develop the property. Under the energetic management of Joseph R. Norrie, rapid progress was made, and production soon attained important proportions. Realizing from the outset the unusual character and potential value in the war effort of the Purdy discovery, the Metals Controller, Department of Munitions and Supply, at once arranged with the Department of Mines and Resources for an official geological report on the area, and also drew the attention of the War Production Board in Washington to what seemed likely to prove a highly important source of strategic-quality mica. Officials of WPB were sent up in the Summer of 1942 to inspect the property, and so impressed were they with the possibility that it might become of high

Jan 1, 1948

By Hugh S. Spence

In the winter of 1941-42, muscovite mica was discovered by a young prospector, Justin Purdy, in the township of Mat-tawan, Nipissing District, Ontario, a few miles north of the small settlement of Eau Claire, which lies on the main Transcontinental Highway (No. 17) between Mattawa and North Bay. Muscovite had been known for many years to occur in the general Mattawa region, and various small efforts at production had previously been made by individuals working scattered deposits in the area. These minor activities, however, had never led to production of any consequence or the discovery of any important mica bodies. The Purdy finds were made in a heavily timbered, mountainous area lying about three miles north of the low-lying settled land along the highway, and in a section not hitherto prospected. The mica taken by Purdy and two partners from surface outcrops proved so remarkable in point of size of trimmed sheets that the find attracted considerable attention, and the area surrounding the three claims taken up by the prospectors was quickly blanket-staked by various interests. Though a number of other mica-bearing pegmatite dikes were found later on these stakings, none proved as rich as those on the original Purdy ground; very little commercial mica was obtained from them and attempts to develop them were short-lived. Purdy and his partners sold their initial production to dealers in Ottawa and Hull, where the Canadian mica industry long has centered. Young Purdy, unfortunately was killed in a motor accident in the early summer of 1942. His father continued mining operations for a few months and produced and sold a considerable amount of mica. In October 1942 the Purdy holdings were acquired by lnspiration Mining and Development Co. of Amos, Quebec, which had been active in staking in the area. This company formed a subsidiary, Purdy Mica Mines, Limited, to develop the property. Under the energetic management of Joseph R. Norrie, rapid progress was made, and production soon attained important proportions. Realizing from the outset the unusual character and potential value in the war effort of the Purdy discovery, the Metals Controller, Department of Munitions and Supply, at once arranged with the Department of Mines and Resources for an official geological report on the area, and also drew the attention of the War Production Board in Washington to what seemed likely to prove a highly important source of strategic-quality mica. Officials of WPB were sent up in the Summer of 1942 to inspect the property, and so impressed were they with the possibility that it might become of high

Jan 1, 1948

By S. G. Lasky

Editorial writers and convention speakers are inclined to lean hard on certain perennial topics which need a better degree of definition. One of those topics is mineral self-sufficiency. Everyone interested in it ought to adhere to the definitions and absorb the background data set forth here by Mr. Lasky which nails down the subject to talkable dimensions once and for all! Mineral self-sufficiency is a flexible concept-one which changes with both economic and political vicissitudes.

Jan 8, 1961

By C. S. Brooks

Several of the commonly used methods for deter-mination of effective grain densities of minerals have been evaluated for accuracy and precision, and their applicability to various types of petroleum reservoir minerals tested. Consideration was given to the effect of consolidation, swelling clay, and wettability on these grain-density determinations. Procedures with helium displacement, a modified low-pressure Boyle's law porosimeter, and liquid displacement (water, n-decane, and n-octanol) were tested. The helium-displacement procedure was used primarily as an independent reference for which the effects of fluid-solid interaction, e.g., adsorption and wettability, were negligible. The procedures with the Boyle's law porosimeter and with liquid displacement are the methods in common use. Minerals investigated included calcite, West Texas limestone core samples, California sandstone core samples, and Wyoming bentonite. The number of samples tested, while not large, was adequate to permit application of statistical methods. Grain-density measurements on calcite (Iceland spar) provided a basis of comparison for the accuracy and precision of the procedures under investigation for a material with a high degree of chemical and physical homogeneity and for which fluid-solid interactions were at a minimum. Liquid-displacement procedures (water or n-decane) provided the greatest reliability and precision for measurement of the grain densities of the limestone tested. Gas-displacement procedures (helium or Boyle's law porosimeter) provided the greatest reliability and experimental convenience, if not the greatest precision, for the measurement of the grain densities of the swell- ing clay, Wyoming bentonite, and the shah sandstones which -contained appreciable amounts of swelling, in-terstitial clays. These experiments were designed to evaluate the applicability of the grain-density procedures in common we to some of the less tractable minerals—tight limestones, shaly sandstones, and swelling clays. The results should provide a useful basis for a selection of the method most suitable for application to the various petroleum reservoir minerals encountered and especially for use in the estimation of formation porosity. INTRODUCTION These experiments were undertaken to evaluate the accuracy and precision of several commonly used methods for determination of effective grain densities of minerals, and to test their applicability to various types of petroleum reservoir minerals. Consideration was also given to the effect of consolidation, clay, and wettability on these grain-density determinations. Procedures used included measurements with helium displacement, with a modified low-pressure Boyle's law porosimeter, and with liquid displacement (water, n-decane, and n-octanol). The minerals investigated included calcite, West Texas limestone core samples, California sandstone core samples, and Wyoming bentonite. The accurate determination of the porosity of petroleum reservoir formations, in particular those of low porosity, has received much attention. Both bulk-volume and grain-volume measurements necessary in the evaluation of porosity have been examined by many investigators with the objectives of improving both the accuracy and the precision of these determinations. In this investigation statistical criteria for selection of the most reliable and suitable procedure for use with a given type of mineral are demonstrated. The grain-volume measurement procedures appear to be the most susceptible to improvement.

Jan 1, 1958

By Alfred James

Some months since, in the Johannesburg gold-fields of South Africa, the attention of the author was directed to certain statements to the effect that the gold-contents of foul or extremely dilute cyanide-solutions could not be effectively precipitated in practice by the usual zinc-method. Such statements caused all the greater surprise, because it is well known that this difficulty is not encountered in other wellknown districts, as, for example, in New Zealand, where solutions containing less than 0.05 per cent. of KCy are regularly reduced in practice to below 1 grain of gold per ton, while in Mexico and the United States almost equally satisfactory precipitations are not uncommon. As a result of these representations, however, the author visited several plants at work in the Transvaal, and noted that while at some few mines the precipitation was really excellent, at others the effluent, after treatment, was much too high in bullion-contents. An investigation into the causes of these unsatisfactory results disclosed the fact that more attention to the close packing of the zinc-shavings in the extractor-compartments tended to improve the results, even with the most dilute solutions. The function of the zinc being one of surface, it stands to reason that a compartment well filled with zinc would be more effective than a half-filled one. Moreover, the quality of the zinc was inferior. This should be in long, tough, thin, light threads; light enough to ignite readily, and tough enough not to disintegrate easily into a slime. The coarse shavings too frequently employed appear to give the reverse of the best practice ; they are brittle, contain less surface, and take up more room. It is almost impossible to pack a compartment properly

Jan 1, 1898

By John Hower, Frank J. Markewicz, William Lodding

Greensand, greensand marl, and green earth are names given to sediments rich in the bluish green to greenish black mineral known as glauconite by the mineralogist. The word glauconite is from the Greek word glaukos, meaning bluish green. The term "greensand" as a rock name for a glauconite-bearing sediment is more appropriate than "greensand marl," a term that has been doggedly perpetuated in the literature. Because of its potash and phosphate content, greensand was dug and marketed as a fertilizer and soil conditioner for more than 100 years. The advent of prepared fertilizers with adjustable nutrient ratios led to the decline of greensand for agricultural application. The material has since been recognized for use in water treatment. Unfortunately, in spite of large reserves and worldwide distribution, the mineral has not been utilized to any significant commercial extent because no major application has been found for a substance with its chemical composition and properties. This lack is probably due to a paucity of research on its potential commercial application. Extraction of potash received considerable attention during and just after World War I. Because of relatively high extraction costs and generally low potash content (up to 8% ), glauconite lost its appeal as a source of this commodity. Historical Background Greensand was used as a fertilizer in New Jersey in the latter part of the 1700s. During the early 1800s its use became more common; applications of up to 100 tons per acre were sometimes made, although recommendations for agricultural use suggested 20 to 50 tons per acre (Tedrow, 1957). Many crops, especially the forage type, were said to improve with greensand application; however, because of, slow release of potash, large quantities were required. Certain greensands that contain sulfur and sulfide minerals are harmful to plant growth, and these were classified as "poison," "burning," or "black marls." The availability of higher-grade potash salts from other mineral sources, and the manufacture of prepared fertilizers, displaced the agricultural use of greensand during the later 1800s. During the mid-1800s the domestic greensand industry, centered in a small section of the eastern United States, grossed more than $500,000 per year. Toward the end of the century, annual production had dwindled to less than $100,000. By 1910 there were only six or eight greensand producers, grossing less than $5000 (Tyler, 1934). There was a small revival in the industry during World War I because of the curtailment of foreign potash, especially from Germany. During the later 1940s and early 1950s greensand was again recommended as a food nutrient for plants and farm crops. Agronomic studies discussed its potential as a soil additive that gradually releases potash and many trace-element nutrients essential for plant growth (Tedrow, 1957). Greensand was sold with the idea that it would condition soil and absorb and hold water while its base-exchange properties would release trace elements. For a short time glauconite was utilized in certain parts of New Jersey as a binding additive in the brick industry, and in the 1800s for making green glass (Cook, 1868). In the early 1900s the base-exchange property of glauconite was recognized for water treatment, and the mineral gained acceptance as a water softener. Mansfield (1922) does not mention base-exchange; however, the base ex-

Jan 1, 1983

By Paul D. Merica, O. B. J. Fraser

PROBABLY the first metallic objects used by man were nickel alloys. In search for flints suitable for the fashioning of their rude tools, our paleolithic ancestors, some 25,000 years ago, quite likely may have come upon some of those heavy, metallic fragments that we now know as meteorites, which consist of an alloy of nickel and iron containing usually from 5 to 15 pct of nickel. Whether paleolithic man ever did discover and use meteoritic fragments, his sketchy records do not actually disclose. We do know, however, that such fragments have been found and used by peoples, particularly the North American Eskimos, for weapons and implements in just the same manner as stones, and prior to any knowledge by those peoples of the reduction of metals from ores. Meteoritic showers were recorded frequently in earliest times and the meteorites often were found and fashioned into useful objects. The ancient Arabic and other myths of "invincible swords fallen from heaven" seem thus to have had a very definite basis in fact, and such weapons, of meteoritic material, have actually been re- covered from archeological excavations. It thus seems probable that meteoric nickel-iron was found and used long before iron was recovered by smelting iron ores (perhaps about 1200 B.C.) and probably even before there was knowledge and use of bronze and gold. Although many centuries were to pass before nickel was first isolated, in 1751, from Swedish ores and recognized as an elemental

Jan 1, 1953