Search Documents

By J. L. Bruce, G. W. Nicolson

THE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydrothermally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CEMENT AND CONCRETE LININGS During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, however, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 1 ½ pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with I2 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concrete and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1947

By John L. Boardman

BECAUSE of the attention that has recently been given to the health and safety of miners by various organizations such as the A.I.M.E., The American Congress, Mining Section, National Safety Council, as well as the Bureau of Mines and various state mining departments, your committee on health and safety deemed it best to call attention this year to the mine-accident cause that is by far the most important; namely, injuries due to falls of ground, rock, roof and coal. Each of several members of the committee contributed a brief outline of the importance of this accident cause in his district. While these papers were brief, it would require too much time and space to give them in full, therefore we present an outline of each and summation of all. REPORT OF M. D. COOPER, HILLMAN COAL AND COKE CO. M. D. Cooper, Division superintendent, Hillman Coal and Coke Co., Pittsburgh, Pa., contributed the following: During the period from 1930 to 1939. accidents from falls of roof in bituminous mines average 54.3 per cent of all accidents. In mechanized mining, there is a tendency toward reduction in this class of accidents because the operator of the machine is usually at a distance of 10 to 20 ft. from the face, whereas in hand loading the miner is close to the face during most of the shift. No doubt the use of aluminum and light steel beams supported at regular intervals by jacks, a common practice in mechanical mining, has contributed to the favorable record so far developed. REPORT OF M. H. FIES, DE BARDELEBEN COAL CORPORATION Milton H. Fies, Vice-President, DeBardeleben Coal Corporation, Birmingham, Ala., says: With reference to the types of mining, it is suggested that a clear understanding be had as to the character and thickness of the directly overlying strata, with especial consideration to the strength and in some cases an analysis of it. In coal mining, generally speaking, overlying strata higher in silica than others is stronger. In changing from narrow to wide places, the procedure should be experimental, both as to the width and depth of places and as to the nature of the necessary timbering. Since most of the accidents in coal mining particularly are due to falls of roof and coal, this phase of mining should be attacked with vigor There is no substitute for discipline and, in this connection, under present conditions it is important that cooperation by the labor organizations be sought and that a spirit of fairness prevail. Frequent and thorough inspection of all active working places should be made.

Jan 1, 1941

By Robert Lindsay

A NUMBER of detailed investigations of the physical changes accom-panying age-hardening have raised the question as to the possibility of some phenomenon preceding the actual process of precipitation. There is considerable evidence to indicate that in the first stages of the aging process there is a pronounced distortion of the crystal lattice. This is particularly marked in duralumin. It would be of considerable theo-retical interest to know the nature of this distortion as compared with that produced in other ways and to find out whether, in supersaturated alloys, it is a necessary antecedent to the formation of a second phase by precipitation. It was believed that a study of the age-hardening char-acteristics of a normally aged alloy compared with one that had been mechanically distorted might supply some useful information on these points. In addition, information would be obtained regarding the effect of a mechanical distortion on any subsequent stage in the aging process. Duralumin was chosen as the material for this investigation because the various aspects of its aging behavior can be shown in detail by suit-able variations of the aging temperature. Also, probably more work has been done on this class of alloys than on any other. In spite of the many published results, it was felt that the experiments would be significant only if all of the work were done on samples from the same source and if they were examined under identical experimental conditions.

Jan 1, 1939

The following is an incomplete list of members and guests who called at Institute headquarters during the period July 10, 1919, to Aug. 10, 1919. Howard C. Arnold, Washington, Pa. J. S. Lane, New York City, N. Y. L. M. Banks, Denver, Colo. H. W. Lawrie, Washington, D. C. George S. Blair, Pittsburgh, Pa. J. L. McAllen, Latouche, Alaska. Richard H. Catlett, Newark, N. J. David F. McFarland, Urbana, Ill. George L. Clark, Council Bluffs, Iowa. James F. Magee, Lancaster, Pa. Capt. Frederick S. Cook, Portland, Ore. A. G. McGregor, Warren, Ariz. John J. Croston, Atlanta, Ga. Emory M. Marshall, Santa Fe, N. M. Thomas Davis, Seattle, Wash. Benjamin L. Miller, Bethlehem, Pa. J. C. Dick, Salt Lake Cite, Utah. 2d Lieut. C. 0. Noble, U. S. Army. Chris. G. Dobson, Vancouver, B. C. Irving Perrine, Hutchinson, Kans. H. S. Emlaw, Grand Rapids, Mich. Fred S. Porter, Seattle, Washington. F. A. Fahrenwald, Cleveland, Ohio. Capt. H. R. Robbins, Peking, China Lieut. James L. Head, St. Louis, Mo. Joseph P. Ruth, Jr., Denver, Colo. A. A. Holland, Napanu, Canada. William A. Simkins, San Francisco, Calif. W. E. Hopper, Washington, D. C. T .V. Smirnoff, Siberia. Harry Hotchkin, Chicago, Ill. Harrison Souder, Cornwall, Pa. L. L. Hutchison, Tulsa., Okla. F. J. Sur, Denver, Colo. Paul S. King, Wilmington, Del. Harry Wolf, Denver, Colo. George K. Anderson, Jr., lies accepted a position as manager for Wight & Co., producers of air-cooled blast-furnace slag, at Longdale, Va. J. M. Armstrong, with the Caribbean Petroleum Co., has been transferred from Philadelphia to Maracaibo, Venezuela. Fred Sherman Baker, who has been with the Oriental Consolidated Mining Co., at Unsankinko, Chosen, Korea, is now at Columbia City, Ind. Ray J. Barber has removed from Roxbury, Mass., to New York City, and is now consulting engineer for the Roxbury Cold Mines, Inc.

Jan 9, 1919

By James P. Kimball

THE object of the present memoir is to put on record some practical experiments by the writer in smelting a silicious native magnetite with no other flux than the silicates of its own gangue: This work was undertaken in the spring of 1878 for Messrs. Naylor & Co., of Boston, to whom I am indebted for the privilege of here communicating its results, these having hitherto only been simply announced.* So far as I am aware these are the first instances of the kind in this country that non-calcareous; or rather non-carbonated, magnetites have successfully been used strictly alone as self-fluxing ores in the blast furnace; that is, without the addition of calcareous flux in the form either of limestone, quicklime, calcareous ore, or basic (calcareous). slag. Previous to the spring of 1878, when the Chateaugay magnetic ore was first brought to my notice, its use had been limited to Catalan forges, after "separation" at the ore bed. The blooms and billets made from it in the several forges of Messrs. Weed & Williams, and of Mr. Williams, were well known in the trade as among the best in the market. The Chateaugay ore beds proving of great magnitude, and the ore exceptionally low in phosphoric acid, it commended itself for blast-furnace purposes to Messrs. Naylor & Co., who employed nee to blow-in the charcoal furnace at Pittsford, Vt., on this ore in the spring of 1878., a previous trial of this ore in the same furnace in the fall of 1877 having proved abortive. This was therefore the first time that Chateaugay ore was successfully smelted in a blast furnace, although since well known as a blast-furnace ore possessing superior and exceptional qualities. The Pittsford furnace, although rebuilt in 1844, and subsequently improved by the former owner, the late J. Prichard, is one of the few furnaces of the old type with open breast (Sumpfofen) still active in this country. Its improvements on furnaces of the period, * Bulletin American Iron and Steel Association, XII, 1878, 132, 156.

Jan 1, 1881

By Chester Washburne

RECENTLY, Messrs. Mills and Wells1 published a thorough chemical study of the waters associated with oil in parts of the Pennsylvania, Ohio, and West Virginia region. Many of their conclusions are of general application and the writer wishes to discuss some of these: Messrs. Mills and Wells show that the composition of the deep brines of the Appalachian fields is such as would be produced by the evaporation of sea water and the precipitation of sodium chloride, combined with reactions with hydrocarbons and other substances. The brines are altered, also, by considerable mixing with meteoric water. They give good reasons for believing that the concentration of the brines was produced by evaporation in the rock pores induced by migrating gas, much of which probably escaped to the surface of the ground. This hypothesis was considered by the writer in a former paper,2 in which main stress was laid on a second hypothesis, that the excess of chlorine in the deep brines may have been due to the entrance of solutions rich in magnesium and calcium chloride which ascended .from a deep, possibly intratelluric, source. Messrs: Mills and Wells present good arguments for the first hypothesis. Underground evaporation by ascending gases probably will be accepted as the best available explanation of the concentration and composition of deep well waters. They have not considered the possibility that, salt waters in deep sands may be concentrated by the diffusion of water vapor through gas into shale. The writer has given reasons3-for believing that capillary forces concentrate gas and oil in the larger openings of rock, such as the pores of sandstones embedded in shale. The gas underground must be nearly saturated with water vapor at; all times, because it always is in contact with the interstitial water of enclosing shales and of the sand-

Jan 9, 1920

By D. C. Hilty

C. E. SIMS*—This is a most interesting and important paper. It is important from two standpoints. First, it has as-spects of being highly accurate and therefore extremely useful to the operating man in showing how far he can go in oxidizing carbon from a steel bath while retaining chromium and the effect of temperature on this limit. Fig 5 is undoubtedly the highlight of the paper, and in checking it against available data, it seems capable of predicting actual results. The other important aspect is the apparently significant fact that reactions within a steel bath, such as between carbon and an oxide, are homogeneous reactions which do not require equilibrium with an external phase. In this case, it seems obvious that the reaction and the equilibrium established were between dissolved carbon (or carbide) and dissolved CrO. The classic reaction which requires equilibrium with solid Cr2O3, did not fit the data. It was recognition of this principle that made Fig 5 possible. G. R. FITTERER*—It might be in assuming the CrO is dissolved in the metal that you are actually approaching the correct factor for activity. If that is true and if the percentages that were used represent an equilibrium constant, this would mean, in effect, that the minimum temperature at which chromium would be reduced by an equivalent percentage of carbon would be about 2400°F from your equation. I believe that is in line with my experience particularly if you deal only with low percentages. J. CHIPMAN†—The author in discussing the equilibrium of the reaction offers two choices of explanation. One postulates an effect of chromium on the activity coefficient of carbon; it would require perhaps more data than are available to us at the present time to test this thoroughly. The other postulate which he offers is a reaction with CrO. This explanation is consistent with physical and chemical principles provided that a solid phase CrO is present, and that is essentially what he is postulating. If that oxide were present one would expect and, I think, almost require the kind of results that he obtained. The weakness of that postulate lies in the lack of confirmatory evidence regarding the presence of solid CrO as such. This should offer an interesting subject for further study. It seems a pity that the theoretical arguments revolving around CrO should have obscured for a moment the very real excellence of this paper. E. CARTER*—I think there is a problem that presents itself in practical application where the metal temperature is from 3200 to 3300 and the temperature desired in pouring is considerably less. B. M. LARSEN†—I get the impression from some of the work that was done earlier that there is probably a localized zone of high temperature at the slag metal interface which effects the removal of the carbon. Without that I wonder if the effect is possible to have a localized superheat and an equilibrium there favorable to low carbon content and

Jan 1, 1950

By L. W. Bahney

FREQUENTLY in using a thermo-electric pyrometer for measuring the temperature of a furnace, a hole is drilled at the back or side of the furnace, through which is introduced the tube containing the thermo-couple. At times the couple is left almost where it drops, for the reason that it soon becomes too hot to be handled easily, and the space at the back or side of the furnace may be so small and uncomfortably hot that an easy and accurate adjustment is nearly impossible. In order to overcome this clumsy and unscientific method of using the thermo-electric pyrometer, I designed an adjustable stand, to hold the clay or quartz tube unclosing the platinum and plati-num-rhodium leads that constitute the couple of the Le Chatelier thermo-electric pyrometer. This stand also allows an easy and rapid adjustment of position to varying heights and angles, as may be desired for special reading. This stand is illustrated in Fig. 1. The couple in the tube might be of better service if the tube were held a little higher above the charge in a roasting-dish, changing the height and angle if desired. The stand, made of 1.5-in, water-pipe and mounted on casters, is heavy enough so it cannot be tipped over easily. It is adjusted to any position, and has a universal clamp which holds the clay or quartz protecting-tube. To avoid disturbing the wires of the couple at the cold junction each time the tube is moved, the cooling-bottle sets in a wire basket so placed that it moves forward or back with the couple. To overcome the necessity of leveling and adjusting a galvanometer at each furnace, a switch-board is used to connect

Jan 1, 1910

By E. W. Newman

During 1943 and 1944, there was an urgent need for certain grades of optical calcite (Iceland spar) for instruments for ' military uses. To find a supply of this material, prospecting was carried out in Montana, California and Colorado. Although some production was obtained by the work in California, the best results were from prospecting the large calcite veins of south central Montana. The bulk of the optical calcite mind during World War II has come from that area. The Bureau of Mines took an active part in the search for optical calcite in Montana. It examined most of the known calcite veins in the 70-mile distance between Wilsall, on the Shields River: and Absarokee, on the Still water River, and conducted exploration on several of the deposits. The Geological Survey also took an active part by mapping many of the veins. Actual mining of the calcite was performed at first by Calcite Operators, Inc., and later by the Metals Reserve Co., through an agent. A sorting plant was established at Clyde Park, where custom material could be sold. These activities stimulated mining by private operators. To be suitable for military uses, the calcite mined had to meet rigid specificstions as to both size and quality. Individual crystals had to be clear and transparent and if in the form of rhombs had to measure at least 7/8 in. on each edge. Some color and a few inclusions in the calcite were allowable, but material with incipient or developed cleavages, or showing twinning other than parallel to the base, was unacceptable. History of Deposits The existence of large veins of calcite in south central Montana has long been known, and for many years the farmers of this region have used the common vein calcite for producing grit for chicken feed. According to reports, the fist optical calcite produced from Montana came from the Cartwright deposit near Grey-cliff,' but until recently the mining of optical calcite in Montana has been limited to spasmodic searching for small crystals suitable for making nicol prisms for saccharimeters and microscopes, or for mineral specimens. The possible need of substantial amounts of optical calcite for military uses began to appear late in 1942 and early in 1943, therefore the Polaroid company began searching for a source of supply in Montana and California. Work on the Wade property near Clyde Park was started on a small scale in the fall of 1942, by .4. H. Hansen, of Clyde Park. During the winter and spring of 1943, a modest quantity of optical calcite was mined and shipped to the Polaroid Corporation, Cambridge, Mass. Most of this was produced from the "Hansen vug," which was found close to the surface. Early in the summer of 1943, mining on the Wade property was undertaken by Calcite Operators, Inc., a company organized for mining optical calcite from the

Jan 1, 1948

By E. W. Newman

During 1943 and 1944, there was an urgent need for certain grades of optical calcite (Iceland spar) for instruments for ' military uses. To find a supply of this material, prospecting was carried out in Montana, California and Colorado. Although some production was obtained by the work in California, the best results were from prospecting the large calcite veins of south central Montana. The bulk of the optical calcite mind during World War II has come from that area. The Bureau of Mines took an active part in the search for optical calcite in Montana. It examined most of the known calcite veins in the 70-mile distance between Wilsall, on the Shields River: and Absarokee, on the Still water River, and conducted exploration on several of the deposits. The Geological Survey also took an active part by mapping many of the veins. Actual mining of the calcite was performed at first by Calcite Operators, Inc., and later by the Metals Reserve Co., through an agent. A sorting plant was established at Clyde Park, where custom material could be sold. These activities stimulated mining by private operators. To be suitable for military uses, the calcite mined had to meet rigid specificstions as to both size and quality. Individual crystals had to be clear and transparent and if in the form of rhombs had to measure at least 7/8 in. on each edge. Some color and a few inclusions in the calcite were allowable, but material with incipient or developed cleavages, or showing twinning other than parallel to the base, was unacceptable. History of Deposits The existence of large veins of calcite in south central Montana has long been known, and for many years the farmers of this region have used the common vein calcite for producing grit for chicken feed. According to reports, the fist optical calcite produced from Montana came from the Cartwright deposit near Grey-cliff,' but until recently the mining of optical calcite in Montana has been limited to spasmodic searching for small crystals suitable for making nicol prisms for saccharimeters and microscopes, or for mineral specimens. The possible need of substantial amounts of optical calcite for military uses began to appear late in 1942 and early in 1943, therefore the Polaroid company began searching for a source of supply in Montana and California. Work on the Wade property near Clyde Park was started on a small scale in the fall of 1942, by .4. H. Hansen, of Clyde Park. During the winter and spring of 1943, a modest quantity of optical calcite was mined and shipped to the Polaroid Corporation, Cambridge, Mass. Most of this was produced from the "Hansen vug," which was found close to the surface. Early in the summer of 1943, mining on the Wade property was undertaken by Calcite Operators, Inc., a company organized for mining optical calcite from the

Jan 1, 1948

By John T. Norton

FoR many years the copper-bearing steels have been of considerable interest to the metallurgist because of their corrosion-resistant properties. More recently the discovery of their definite age-hardening characteristics has focused attention on them again. In a recent paper, Smith and Palmer(l)† have given an admirable description of the behavior of a considerable number of steels of this type and a study of their results suggests two questions of a more or less fundamental sort. In the first place, it has been plainly shown that the hardening effect of added copper does not increase up to the maximum solubility of copper in iron as given by earlier investigators, but reaches its greatest value considerably below this point. This fact suggests that either the solubility is not so great as previous investigators have stated, or that the age-hardening mechanism is not the simple precipitation phenomenon that has been postulated. In the second place, the nature of the aging mechanism in this particular system should be determined. Recent developments in the study of age-hardening processes have shown that the increase of hardness is often, but not always, accompanied by precipitation and the action of a particular system is not predictable on the basis of its components or type of phase diagram. It would be of considerable interest to study the aging of the iron-rich iron-copper alloys in detail. One would like to know whether the aging mechanism is different at high and low aging temperatures, and whether the extreme sluggishness of the system may perhaps represent some new type of aging process. The experiments to be described were carried out in an endeavor to answer these questions. Obviously, in such experiments it is important to confine the hardening effect to the single element, copper, so that iron and copper of high purity must be used in the preparation of specimens. An observation of lattice changes during the aging process, correlated with the hardness changes, seems to be the best available method of

Jan 1, 1935

By John T. Norton

FoR many years the copper-bearing steels have been of considerable interest to the metallurgist because of their corrosion-resistant properties. More recently the discovery of their definite age-hardening characteristics has focused attention on them again. In a recent paper, Smith and Palmer(l)† have given an admirable description of the behavior of a considerable number of steels of this type and a study of their results suggests two questions of a more or less fundamental sort. In the first place, it has been plainly shown that the hardening effect of added copper does not increase up to the maximum solubility of copper in iron as given by earlier investigators, but reaches its greatest value considerably below this point. This fact suggests that either the solubility is not so great as previous investigators have stated, or that the age-hardening mechanism is not the simple precipitation phenomenon that has been postulated. In the second place, the nature of the aging mechanism in this particular system should be determined. Recent developments in the study of age-hardening processes have shown that the increase of hardness is often, but not always, accompanied by precipitation and the action of a particular system is not predictable on the basis of its components or type of phase diagram. It would be of considerable interest to study the aging of the iron-rich iron-copper alloys in detail. One would like to know whether the aging mechanism is different at high and low aging temperatures, and whether the extreme sluggishness of the system may perhaps represent some new type of aging process. The experiments to be described were carried out in an endeavor to answer these questions. Obviously, in such experiments it is important to confine the hardening effect to the single element, copper, so that iron and copper of high purity must be used in the preparation of specimens. An observation of lattice changes during the aging process, correlated with the hardness changes, seems to be the best available method of

Jan 1, 1935

By W. E. Coxe

In 1857 the Philadelphia and Reading Railroad Company, whose main line extended from Philadelphia to Pottsville, Pennsylvania, with branches into the coal regions of Schuylliill County, made a contract with the Fairmount Rolling Mill, at Philadelphia, for the rerolling of some four thousand tons of iron rails. The essential features of the agreement were that the old rails should be piled with puddled iron and rolled into flats for the rail pile, which latter was • to be of a section seven inches square, and after being heated, and reduced, by rolling, to a bloom of a section about fire inches by six inches, was to be reheated, before being finished into the rail of the T pattern, four inches high, weighing sixty-four pounds per yard. Great care was exercised in the execution of this contract, and the rails being distributed over all parts of the road, gave general satisfaction by their excellent wear. Five years afterward, the principal proprietor and manager of the Fairmount Rolling Mill was elected President of the Reading Railroad, and very many of the rails made under his supervision were still in use in the tracks of the company, of which he had just assumed the management. His first efforts were, therefore, directed to the procuring of more rails of the same quality wherewith to replace those worn out. Here he encountered some trouble, makers refusing to bid because of the details in the specification, the required reheating being the objectionable feature, for which it was generally intimated they would not be sufficiently remunerated for the increased labor, extra coal consumed, and the changes necessary from the established methods of working. Most of the new rails were, therefore, bought, and the old rails rerolled without regard to any particulars as to the manner of piling, heating, etc., each manufacturer furnishing what he deemed the best article possible for the money. As a consequence, rails of all imaginable grades were placed in the tracks, some giving out in six

By W. E. C. Coxe

IN 1857 the Philadelphia and Reading Railroad Company, whose main line extended from Philadelphia to Pottsville, Pennsylvania, with branches into the coal regions of Schuylkill County, made a contract with the Fairmount Rolling Mill, at Philadelphia, for the rerolling of some four thousand tons of iron rails. The essential features of the agreement were that the old rails should be piled with puddled iron and rolled into flats for the rail pile, which latter was to be of a section seven inches square, and after being heated, and reduced, by rolling, to a bloom of a section about five inches by six inches, was to be reheated, before being finished into the rail of the T pattern, four inches high, weighing sixty-four pounds per yard. Great care was exercised in the execution of this contract, and the rails being distributed over all parts of the road, gave general satis¬faction by their excellent wear. Five years afterward, the principal proprietor and manager of the Fairmount Rolling Mill was elected President of the Reading Railroad, and very many of the rails made under his supervision were still in use in the tracks of the company, of which he had just assumed the management. His first efforts were, therefore, directed to the procuring of more rails of the same quality wherewith to replace those worn out. Here he encountered some trouble, makers refusing to bid because of the details in the specification, the required reheating being the objectionable feature, for which it was generally intimated they would not be sufficiently remunerated for the increased labor, extra coal consumed, and the changes necessary from the established methods of working. Most of the new rails were, therefore, bought, and the old rails rerolled without regard to any particulars as to the manner of piling, heating, etc., each manufacturer furnishing what he deemed the best article possible for the money. As a consequence, rails of all imaginable grades were placed in the tracks, some giving out in six

Jan 1, 1877

By R. D. Hagni

The following is a case study illustrating the use of thin sections and polished sections of crude ore to predict metallurgical response. By examining polished sections of the metallurgical products, the textural and mineralogical reasons for unsatisfactory separation can be explained. An area of oxidized Negaunee Iron-Formation located south of Negaunee, Michigan, in the Marquette Iron Range, has been considered for roast reduction-magnetic separation. Preliminary metallurgical studies and subsequent pilot plant testing produced varied results. These results prompted this microscopic study which began with an examination of 126 thin sections and 82 polished sections prepared from 126

Jan 1, 1967

By E. J. Roberts, E. B. Fitch

Most classifiers in use today are, in function, settling pools. A fluid suspension of particles is passed through a pool at such a rate that only a fraction of the particles-the coarser fraction-has time to settle out of suspension. The rest are carried on out of the pool as overflow. The most fundamental way in which such classifiers differ is in the mechanism used to remove the settled particles from the pool. The particles may gravitate from the pool, as in the various sand cones, or they may be conveyed mechanically from the pool by drags, spirals, or reciprocating rakes. The mechanism of settling pool classification and its limitations are discussed. A method for calculating countercurrent classifications is presented. The practical validity of the calculation method has been confirmed through 20 years of use within The Dorr Co. During this time it has been used on diverse feeds and has been checked against many types of settling pool classifiers, with close agreement in nearly every case. Excellent elimination of third critical mesh particles and finer ones may be obtained in a countercurrent classifications series where all stages separate at the same mesh, but elimination of first and second criticals is inherently limited. Spectacular elimination of all criticals may be obtained by arranging successive stages to classify at successively coarser mesh. Improvement in elimination is obtained at the cost of an increased internal recirculation, but this may be tolerable in many cases.

Nov 1, 1956

THERE have been two important accomplishments of the Truman administration; the Hoover Commission report on inefficiency and waste in government and the report of the Paley Commission on the natural resources of the United States. Both reports are in the interest of the American people and should transcend the boundaries of political parties. Both reports are starting points for the formulation of policies which must be continuously revised to meet changing conditions. Regardless of the outcome of the election the principles embodied in these two great documents must be kept alive. The Paley report is right in our own bailiwick of mineral raw materials and it behooves us to study it carefully as our responsibility to posterity. To those in the mining industry who have limited their field of observation to moving rock or to metal prices it may come as a surprise that our production of such staples as copper, lead, and zinc has fallen behind increased requirements to the point that substantial tonnages must be imported. Iron ore is next on the list and everybody knows that such metals as tin, tungsten, chromium, manganese, nickel, and cobalt are imported almost exclusively. The crisis in raw materials pointed up by the Paley report has been reported annually by Elmer Pehrson and others to small gatherings at the Mineral Economics Division sessions at the Annual Meeting for as long as we can remember. In September 1949, the United Nations Economic and Social Council held an international resource conference at Lake Success which disclosed these same grave conclusions: - Consumption of raw materials is multiplying at an alarming rate, faster than discoveries or replacements are being made. - Production has been wasteful and utilization lavishly beyond enginee¬ing and practical requirements. - Industrialized nations are depleted and many raw materials consumed by industry are not found in the industrialized countries. - Nations formerly exporters of raw materials are increasingly building their own consuming industries. - Political forces in the world are limiting access to raw materials. The Paley Commission selecting the quarter century, 1950 to 1975, to project raw material requirements for the United States, pointed out obstacles to meeting these requirements, and made recommendations for procurement. It is not important that we disagree that cobalt consumption will reach 344 pct of present, or fluorspar 187 pct when iron and ferroalloys are only expected to increase 75 pct. What is important it that the fabulous appetite of the United States for mineral raw materials has consumed more since World War I than was consumed by the entire world in all recorded history prior to 1914. And, unless the people of the United States are satisfied to remain at their present standard of living (which is unthinkable) this consumption is correctly plotted by the Paley Commission as continuing to expand. If the U. S. is to continue on a course of progress, it must procure raw materials wherever it can at the lowest possible cost. Natural resources are clearly an area in which the broadest cooperation between industry and government must exist to achieve efficient exploitation, economic consumption, and expansion of sources of supply. The message of the Paley report requires action comparable to that of the North Atlantic Pact. Its implication is as significant as military preparedness. It is a world problem. It is a mining engineering problem. Don't let it die!

Jan 1, 1952

By Orson Shepard

TEXTBOOKS on fire assaying list the following standard methods of assaying sulphide ores: (1) scorification, (2) litharge-niter, (3) soda-iron, (4) roasting, (5) combination wet and fire. The litharge-niter method has proved the most satisfactory, and is the usual method for assaying sulphide ores and concentrates. It gives good results when suitably conducted and when lead buttons of uniform size are produced so that the cupellation temperature can be properly controlled. The main objection to the method is the inconvenience of determining the amount of niter to add to each assay charge to produce lead buttons of suitable size from a set of fusions. For the assay of different materials, the niter requirement varies with the particular sulphide minerals present, the amount of sulphide minerals present, the slag composition, and the rate of heating the charge in the furnace. Except for some materials, so uniform in composition that the same amount of niter can be used in assaying all samples, the amount of niter must be determined for each sample to be assayed. This is done by either: (1) calculation from an estimate of the kind and amount of sul-phide minerals present in the sample, or (2) a preliminary fusion. Some assayers use one method and some the other. The estimation method takes the least time; but much experience is required to obtain close estimates on a wide variety of materials. At best, the sizes of the lead buttons obtained vary considerably. The preliminary fusion method usually gives lead buttons of fairly uniform size, although sometimes there is a variation because the oxidizing power of niter varies a little with the charge. This variation can be eliminated by two preliminary fusions: one to determine the reducing power of the ore, and the other to determine the oxidizing power of niter in the charge. The objection to the prelimi-nary fusion is the extra time and expense involved.

Jan 1, 1939

By Pol Duwez, Spencer R. Baen

A LTHOUGH the practical importance of Fe-Cr--iV Mo alloys has long been recognized, constitution studies have been limited to a few alloys within rather narrow ranges of composition. The purpose of the present study was to establish the phase boundaries in the ternary diagram at a temperature of 1200°F (650°C).* The identification of phases and the determination of phase boundaries were based primarily on X-ray diffraction measurements and occasionally on microscopic observation. The methods used for locating the phase boundaries were essentially those described in detail by Andersen and Jette,' and by others.', The compositions of 180 alloys, prepared by powder metallurgy techniques, are shown in Fig. 1. The chemical analysis and mesh size of the powders which were used for the preparation of the alloys are given in Table I. The powders were mixed for 48 hr or longer, then compacted under 80,000 psi in a %-in. diam steel die. Each specimen weighed approximately 5 g. The compacts were sintered for 4 hr at 2500°F (1371°C) in an atmosphere of pure dry hydrogen (dew point near the temperature of liquid nitrogen). An open tray of chromium powder was placed upstream of the compacts to act as a "getter" for the last traces of oxygen or water vapor. In many cases this chromium powder was bright after sintering. Occasionally the upstream side of the powder was slightly greenish, but in all cases the downstream side was metallic. Some of the alloys contracted during sintering and some expanded as much as 20 pct. The latter alloys, which in all cases were brittle, were crushed in a tool steel mortar, repressed, and resintered for 4 hr at 2500°F. After sintering, the alloys were aged for ten days at 1200°F (650°C) in evacuated (105 mm Hg or better) fused silica tubes and were cooled rapidly to room temperature following the aging treatment. The use of the powder metallurgy technique in preparing alloys for structural investigation offers a simple method 'of avoiding contamination or non-homogeniety which could result from a melting operation. It is very often possible to dispense with chemical analysis of the alloys which have been prepared by the powder metallurgy method. In lieu of chemical analysis, it is necessary to determine the weight of the compact before and after sintering. The chemical composition of the alloy may be considered as that of the green compact, within the limits of accuracy determined by the loss of weight during sintering. In phase-diagram studies it is important to achieve homogeniety in structure, whether the alloys are prepared by powder metallurgy or by melting. Homogeniety means complete diffusion during the sintering of the alloys which are prepared by powder metallurgy. It has been found from experience that the best criterion for establishing the completeness of diffusion is the sharpness of the X-ray diffraction patterns. This criterion has been used throughout the present study. The X-ray diffraction data were obtained using powder cameras of either 214.86 or 71.62 mm diam. Copper, cobalt, or chromium Ka. radiation was used, the choice being based on the alloy composition. The powder samples were obtained by filing or crushing, depending on whether the alloy was ductile or brittle. In some cases, the powder was annealed for 4 to 6 hr at 1200°F in vacuum. The measurements were corrected for film shrinkage and absorption. The large camera, in which the film is mounted

Jan 1, 1952

By T. W. Guy

IN approaching the problems of sampling coal, a brief statement of certain facts that are more or less taken for granted may he helpful: 1. The coal-mine operator needs reliable data as to the physical and chemical characteristics of his coal in order to plan and control intelligently its mining, preparation, and marketing. The consumer needs such data in order to select the equipment and the coal best suited to meet his requirements, to check the quality of fuel delivered, and the efficiency of its use. Various government control agencies require such data as a basis for classifications and establishment of limits, for use in carrying out the requirements of federal, state or municipal laws. 2. All such data must be obtained by analyses, measurements, or tests made on samples, which are taken to represent the coal tested. It is now becoming generally recognized that, in accordance with statistical laws, test results from samples are not expected to represent the exact qualities of the lot or lots from which they are taken, except within statistical, or "expected" limits. Such limits are definitely specified by some present standards of the American Society for Testing Materials and the British Standards Institution. 3. Samples that give ash within satisfactory limits are usually assumed to be sufficiently accurate for other analyses, except under special conditions such as meeting close specifications for coals showing wide variability in sulphur, fusibility of ash, or other quality. 4: In. modern coal sampling the increment is recognized as the basis for taking samples. For a given accuracy the number and weight of increments specified are increased with: (a) the expected ash, and (b) the top size designation of the lot to be sampled. 5. It is extremely important that every sampler recognize that: the specified number and weight of increments are minimums, and that. the precautions to be used in order to take them properly are also minimums; that in the reduction of the gross sample the sizes specified for the coal after each stage of the crushing are maximum; that the quantities specified to be taken after each crushing stage are minimum; that any short cuts or failures to meet the requirements specified will reduce the statistical accuracy of the results, although it is possible that one or two checks on a few results may seem to show otherwise.

Jan 1, 1943