Search Documents

Readers of recent Bulletins have doubtless observed that the problem of improving both material and moral condition of employees is receiving close attention from influential members of the Institute. This will lend interest to certain developments and investigations that have been reported elsewhere.

Jan 5, 1918

CONTENTS PAGE GEISMER, H. S.-Coal Washing Practice in Alabama. Discussed by William Kelly, H. S. Geismer, H. D. Pallister, L. E. Bryant, Milton H. Fies, Elmer F. Harris, James A. Barr, George G. Crawford, E. C. Wright, George S. Rice, R. V. Norris 1 MILLER, F. W.-Byproduct Coking in Alabama. Discussed by Theodore Swann 4 FIES, MILTON H.-Alabama Coal Mining Practice. Discussed by Milton 11. Fies, R. V. Norris, R. D. Hall, L. E. Bryant, George S. Rice, H. S. Geismer 5 MUSSEY, H. E.-Blast-furnace Practice in Alabama. Discussed by C. A. Meissner, Franklin H. Crockard, H. E. Mussey, W. H. Oldham 14 Coal Washing Practice in Alabama Discussion of paper of H. S. GEISMER, presented at the Birmingham Meeting, October 1924, and issued, as Paper No. 1363-C, with MINING AND METALLURGY, September, 1924. WILLIAM KELLY, Iron Mountain, Mich.-Is the dry-cleaning method used? H. S. GEISMER.-Neither the dry-cleaning process nor the Chance sand-liquid method has been tested in Alabama; but all other methods used for cleaning bituminous coal have been largely brought to perfection in this state. H. D. PALLISTER, Tuscaloosa, Ala.-Have you the results from the recent work on the tables with reference to fine coal? H. S. GEISMER.-None of the iron-producing companies has adopted the tables, though three commercial operators have installed tables within the last six months. I tried to learn the results, but they were not willing to release the data just now. At the mines producing domestic coal, fines present a difficult problem; until within the past six months all the fine coal was wasted. The operators are trying to recover some of it on the table. L. E. BRYANT, Rockwood, Tenn.-Is there any connection between the sulfur content of the sludge and the effect of the sludge on vegetation?

Jan 7, 1925

By J. H. Henderson, J. Naar

The displacement of a wetting fluid from a porous medium by a non-wetting fluid (drainage) is now reasonably well understood. A complete explanation has yet to be found for the analogous case of a wetting fluid being spontaneously imbibed and the non-wetting phase displaced (imbibition). During the displacement of oil or gas by water in a water-wet sand, the porous medium ordinarily imbibes water. The amount of oil recovered, the cost of recovery and the production history seem then to be controlled mainly by pore geometry. The influence of pore geometry is reflected in drainage and imbibition capillary-pressure curves and relative permeability curves. Relative permeability curves for a particular consolidated sand show that at any given saturation the permeability to oil during imbibition is smaller than during drainage. ' Low imbibition permeabilities suggest that the non-wetting phase, oil or gas, is gradually trapped by the advancing water. This paper describes a mathematical image (model) of consolidated porous rock based on the concept of the trapping of the non-wetting phase during the imbibition process. The following items have been derived from the model. 1. A direct relation between the relative permeability characteristics during imbibition and those observed during drainage. 2. A theoretical limit for the fractional amount of oil or gas recoverable by imbibition. 3. An expression for the resistivity index which can be used in connection with the formula for wetting-phase relative permeability to check the consistency of the model. 4. The Iimits of flow performance for a given rock dictated by complete wetting by either oil or water. 5. The factors controlling oil recovery by imbibition in the presence of free gas. The complexity of a porous medium is such that drastic simplifications must be introduced to obtain a model amenable to mathematical treatment. Many parameters have been introduced by others in Iprogressing" from the parallel-capillary model to the randomly interconnected capillary models independently proposed by Wyllie and Gardner3 and Marshall4. To these a further complication must be added since an imbibition model must trap part of the non-wetting phase during imbibition of the wetting phase. Like so many of the previously introduced complications, this fluid-block was introduced to make the model performance fit the observed imbibition flow behavior. THE IMBIBITION MODEL ASSUMPTIONS The following assumptions are common to many two-phase models previously described. 1. The wetting characteristics of the medium are clearly defined. 2. When two fluids co-exist in the medium, the wetting phase will fill the smaller pores and the non-wetting fluid the bigger ones. 3. The pores have a circular cross section. 4. Apparent pore radii are related to the capillary pressure (drainage) by

By C. S. Giggins, F. S. Pettit

The oxidation of Ni-Cr alloys in 0.1 atm of oxygen has been studied at temperatures between 800" and 1200°C. For alloys with 30 wt pct or more Cr, continuous layers of Cr2O3 are formed during oxidation. In the case of alloys with chromium concentrations between approximately 5 to 30 wt pct, external scales of Cr203 are formed over grain boundaries whereas internal precipitates of Cr2O3 and external layers of NiO are formed at other areas on the alloy surface. When such conditions are present on the alloy surface, chromium diffuses laterally from those areas covered with a continuous layer of Cr2O3 to areas where a Cr2O3 sub scale exists and it is possible for the sub-scale zone to become separated from the alloy by a continuous layer of Cr2O3. Whether such a state will be attained depends upon the initial grain size of the alloy and the oxidation time. When the concentration of chromium in the alloy is less than 5 pct, Cr2O3 is formed internally both at grain boundaries and within the interior of grains and the alloy is covered with an external layer of NiO. MECHANISMS which describe the growth of oxide scales on nickel-base superalloys are complex and the effects produced by the various elements in these alloys on the oxidation behavior of superalloys are not clearly understood. In order to determine the influence of the different elements on the oxidation behavior of superalloys, it is first necessary to examine the oxidation properties of binary nickel-base systems which contain the principal elements present in the superalloys and then progressively more complex systems until compositions typical of the superalloys are attained. Chromium is present in virtually all nickel-base superalloys and the purpose of the present studies was to examine the selective oxidation of chromium in Ni-Cr alloys. The oxidation characteristics of Ni-Cr alloys have been extensively studied1-" to date principally as a result of the high oxidation resistance exhibited by some of these alloys. Ni-20Cr* has long been known *All compositions are given as wcight percent unless specified otherwise. to be oxidation resistant and is commonly used as resistance heating elements for service temperatures up to 1100°C. This alloy cannot be used for extended periods of time at higher temperatures because of the apparent reaction of the external scale with oxygen to form gaseous CrO3. In spite of the considerable work cited above some important aspects of Ni-Cr oxidation still remain unresolved. Virtually all of the previous studies agree that small additions of chromium to nickel, e.g., <10 wt pct Cr, result in increased oxidation rates as compared to that of pure nickel, whereas larger additions, e.g., 20 to 30 wt pct Cr, form alloys with substantially lower oxidation rates. The controversial aspects of the oxidation mechanisms for these alloys that still remain unresolved are as follows: 1) A description of the oxidation mechanism for the low chromium alloys. 2) A description of the oxidation mechanism for the high chromium alloys, particularly with respect to the composition of the external scale which results in the lower oxidation rates. 3) The specific alloy compositions at which the oxidation mechanism changes from that obtained for low chromium contents to that of the high chromium alloys and the reason for this transition. EXPERIMENTAL The Ni-Cr alloys listed in Table I were prepared from high purity metals by nonconsumably arc melting and casting as buttons. These alloys were then given a preliminary annealing treatment in argon at 815°C for 100 hr to promote homogeneity. Each button was cut into 0.250 in. thick sections that were subsequently cold-rolled to 0.050 in. thicknesses and annealed in argon at 815°C for 48 hr to provide a twinned, equi-axed grain structure. The grain size for these alloys was not uniform and the limits, within which the average grain size lies, are given in Table I for the single-phase alloys. All the alloys were single phase with the exception of the Ni4OCr alloy in agreement with the Ni-Cr phase diagram.&apos;&apos; Rectangular specimens were cut from the sheet to provide surface areas of approximately 2.5 sq cm. Exact areas were determined with a micrometer after surface preparation was completed. All of the specimens except the Ni-40Cr alloy and pure chromium were polished through 600-grit Sic abrasive paper, ultrasonically agitated in ethylene trichloride, rinsed with ethyl alcohol, and electro-polished. The specimens were electropolished in a 10 vol pct H2SO4 (conc), 6 vol pct lactic acid, methyl alcohol solution at 70" to 80°C for 2 min at a current density of 0.8 to 1.2 amp per sq cm. This electro-polishing procedure did not produce acceptable surfaces on the Ni-40Cr alloy nor on pure chromium and the oxidation properties of these materials were obtained for specimens polished through 600-grit Sic

Jan 1, 1970

By J. L. Wright

When management is confronted with the risk of constructing a waste disposal well, these are some of the questions which may arise. Should the company expand the present waste treatment plant? More lagoons will cut into valuable acreage which might be needed later, and yet the pollution engineer says he can guarantee results. On the other hand, does the formation being used for those successful disposal wells off to the west extend over far enough to be used for the company&apos;s own well? Will the formation be thick enough? Will it be too deep? Will it be porous and permeable enough? Apart from needing to make a profit on the products made at the plant, plant officials must sometimes act under pressure to comply with pollution standards. The manager must build the cost of the pollution control system into the price of the products made by the company.

Jan 1, 1970

By A. M. Abouzeid, S. Chander, D. W. Fuerstenau

Today numerous ores contain valuable minerals in finely disseminated form; and although the recovery of these fine mineral particles is generally exceedingly difficult, diminishing raw material resources necessitates the recovery of such mineral values. In many systems, the efficiency of recovering fine particles is still extremely low and often fine particles must be discarded as slimes. However, in recent years, various advances have taken place in the recovery of mineral particles in the very fine size range. In this paper, the background and performance of a number of processes for fine particle processing and separation are reviewed and discussed, particularly from the point of view of how fine particle recovery might be improved.

Jan 1, 1979

By R. C. Mahon

THE Homer iron-ore mine is at Iron River, Mich. Because it covers a large area, 400 acres, and because there was a considerable depth of water in the glacial drift above most of the ore bodies, this mine has presented a number of unusual and often difficult operational problems. The purpose of this paper is to discuss a few of the most important problems encountered. SURFACE WATER Mining on this property was started on one 40-acre tract. The ledge in this area was the highest on the property and, although it was a real problem, water could be handled by underground pumping. During the first period of mining, drifts were driven just under the ledge and holes were drilled through to the surface material. In later years these drifts have been extended wherever possible. Although these drifts assisted in the drainage problem, it was evident they would not be sufficient alone. Before mining on a large scale could be started on this property, the water problem had to be solved. A number of test holes were put down to the ledge, and showed that there was an average 150 ft. of water-saturated glacial drift above the ledge over the rest of the mine. The upper 70 ft. was gravel and sand and the lower 80 ft. clay and hard pan, with some narrow seams of sand and gravel. It was evident that the water above the clay seam could not be drained off through openings in the ledge and for that reason it was decided to install surface drainage wells. This method of drainage was entirely new at that time and was pioneered at the Homer mine. The sinking of the first well was started in June 1929. Immediately following the first well a number of wells were sunk, but only to the top of the clay seam. This was done with the idea that a greater capacity could be obtained in a shorter time from gravel seams where the water flowed more freely and that the cost of pumping the water above the clay seam would be considerably less than if the wells had all been sunk to the ledge at once. Before the drainage of surface water was started, 1200 gal. per min. against a head of 800 ft. was being pumped from the mine. By March of 1932, with five surface wells in operation, the mine pumping had been reduced to 150 gal. per min. At this time we were pumping 5000 gal. per min., under an average head of 110 ft. from the surface wells. The total pumping costs were 30 per cent less than in 1929 because the greater capacity was being pumped at a much lower head. From 1932 to 1936 the mine was idle and all surface pumping was stopped. Since 1936, 10 new wells have been added with a total pumping capacity of 8000 gal. per min. at the present time. The water level has been lowered 70 ft. since surface pumping was started in 1929, and it is now approximately at the top of the clay. To remove the water below the clay seam, 11 of the 15 wells were sunk to the ledge.

Jan 1, 1945

By B. Misra, N. Brook

A new method of determining a "Rock Impact Hardness Number" by comminuting cylindrical specimens in a "Syskov" mortar is proposed. The method of finding Protodyakonov Number by the stamp-mill method was first examined, and the effect of initial size of specimen thoroughly investigated. A method of determining the correct number of blows to use in a test is developed and the inaccuracies involved in the original method, which stem from the measurement of a volume of fines, are avoided by using mass measurements. A graph of percentage fines below 50µtm and number of blows is statistically examined to obtain an accurate estimate of the number of blows to produce 25% fines, from regular initial specimens. This number was defined as the "Rock Impact Hardness Number". The effect of specimen size on this strength index was investigated. A comparison was made between this method of determining rock strength, and a &apos;field&apos; method using irregular specimens.

Jan 1, 1971

By J. E. Tiffany, S. S. Lubelsky

For blasting in coal mines the U. S. Bureau of Mines recommends that permissible explosives be used exclusively, that these shall be fired electrically, and that where feasible the working place shall be cut or sheared. These recommendations are made to promote safety and prevent mine explosions. Although permissible explosives are not flameless, their lower flame temperature and shorter duration of flanie make their use safer than that of nonpermissible explosives. Mixtures of air with both methane and bituminous coal dust, which are liable to occur in coal mines, may be ignited by coming in contact with any type of flame or spark of sufficient temperature and duration or by the firing of a blast. In a working place where a blast is to be fired, in addition to the use of permissible explosives, adequate ventilation for the dilution and removal of accumulations or outbursts of flammable gas should be provided. Bituminous coal mines should be rock-dusted as a means of rendering the coal dust harmless The efficient use of permissible explosives depends upon the proper preparation of the working place, standardized drilling, the strength characteristics of the explosive, and the use of a proper weight of charge. Experienced shotfirers should load, tamp and fire all holes. The major part of the information and data here presented is based on the results of efficiency tests made in large producing mines of Pennsylvania and Illinois. Bureau of Mines Report of Investigations, Serial No. 2697, describes how a standard method of blasting was worked out and put into operation in a mine in southern Illinois.&apos; This paper contains a description of the methods worked out subsequently in another mine in that district. Descriptions of tests in two Pennsylvania mines are given in Bulletins 11 and 19 of the Carnegie Institute of Technology.2 These tests

Jan 1, 1928

By Douglas Ashmead

In his paper Mr. Braley makes no mention of the bacteriological aspects of the problem. It is now quite well established that certain bacteria play a major role in formation of acid mine waters, and it is a simple matter in the laboratory to show that under sterile conditions the rate of acid production from a pyrites suspension is only about one quarter of that obtained from a similar suspension inoculated with drainage from a mine producing an acidic pit water. Under sterile conditions the oxidation is due to direct chemical action and, from the evidence just given and from much other evidence, this increase under nonsterile conditions is due to certain bacteria. Experiments recently completed, and shortly to be published, have shown that this bacteriological oxidation can be prevented by the maintenance of pH conditions above 4. It was found that to raise this pH above 4 at the beginning of the experiments was not sufficient but that, due to the continuing chemical oxidation, alkali had to be added daily to maintain the pH conditions above 4. The amount of alkali added, however, over a fixed period, was only about one quarter of the alkaline equivalent of the acid produced when pH conditions were not controlled over an equal period. The opinion expressed by Mr. Braley that sodium hydroxide has little or no effect on the rate of oxidation of pyrites is not substantiated by the above experiments. The writer does not claim that these results show a practical solution to the problems, especially in abandoned workings, but feels that the application of an alkaline coating, such as lime wash, to exposed accessible workings might be well worth trying. S. A. Braley (author&apos;s reply)—In 1919 Powell and Parrl suggested that bacteria, or some catalytic agent, hastened the oxidation of pyritic or marcastic sulfur in coal. Carpenter and Herndon (1933)&apos; attributed the action of Thiobacillus thiooxidans. Colmer and Hinkle (1947)3 observed an organism similar to T. thiooxidans and another organism that oxidized iron. Leathen and Braley 9rst discovered this organism in 1947 in a sample of water from the overflow of the Bradenville mine (Westmoreland County, Pennsylvania). They characterized the organism in 1954" and gave it the name Ferrobacillus ferrooxidans. Although Temple and Colmer (1951)&apos; had suggested the name Thiobacillus ferrooxidans, since they claimed it oxidized both ferrous iron and thiosulfate, we have found that pure cultures of the organism do not oxidize thiosulfate, hence the name F. ferrooxidans. In 1955 Ashmead7 isolated an organism, similar to the one called Thiobacillus ferrooxidans by Temple and Hinkle, from acid mine water in Scotland. It is probable that this organism was F. ferrooxidans. In 1954 Bryner, Beck, Davis, and Wilsonh reported microorganisms in effluents from copper mine refuse. These organisms appeared to be similar but were not in pure culture. In view of this history of bacterial investigation of acid mine water and our own ten years of experience, we do not agree with Mr. Ashmead that bacteria play a major role in acid formation. We do not find that any of these bacteria will directly oxidize pyritic material. They do, however, augment the chemical formation of sulfuric acid by atmospheric oxidation. In two papers in 1953% eathen, Braley, and McIntyre discuss the role of bacteria in acid formation and postulate the mechanism through which they operate. Mr. Ashmead in his discussion of my paper has assumed that this work was carried on in the presence of acid mine water in which bacteria would be present. This was not the case. Strictly sterile conditions were not maintained, but the organisms present in mine drainages were definitely absent in these experiments. We believe that we have demonstrated that alkalis do not inhibit the chemical oxidation of pyritic material. This is also indicated by Mr. Ashmead&apos;s discussion in which he says that alkali must be added daily due to the continuing chemical oxidation. It is interesting to note that Mr. Ashmead finds that maintenance of pH above 4.00 decreases the activity of the bacteria. We have found also that a decrease in pH below 2.8 also inhibits its activity. Table XIII of published data&apos;" illustrates the decrease in activity with increased acidity, although pH values are not given. These values are in comparison with uninoculated controls and show the marked increase in acidity up to 22 weeks but a decline at 29 weeks, at which time the experiment was terminated. It is probable that after a longer period only chemical oxidation would have continued. From our studiesv we have postulated that the iron oxidizing bacterium (Ferrobacillus ferrooxidans) oxidizes the ferrous iron, resulting from chemical oxidation, to ferric iron. The ferric iron then aids the atmospheric oxidation of the sulfuritic material and is itself reduced to ferrous iron, which in turn acts as food for the autotrophic bacteria. Study of the physiologic properties of F. ferrooxidans shows that its preferred pH is about 3.00 and its activity decreases with variation in either direction. It is extremely inactive above pH 4.00 and below 2.5. This inactivity above 4.00 is indicated by Mr. Ashmead&apos;s observations. These properties of F. ferrooxidans then correlate perfectly with our hypothesis. Ferrous iron is oxidized very slowly by atmospheric oxygen in highly acid sohtion and since the bacteria become inactive, acid is formed only by atmospheric oxidation. At a pH of 4.00 or above iron is more readily oxidized by atmospheric oxygen, but the bacterial activity is decreased. However, with a pH above 4.00 the ferric iron is removed from the field of activity since its soluble sulfate hy-drolyzes and precipitates the iron as ferric hydroxide or a basic sulfate. As we have shown in the paper under discussion, the alkali does not inhibit the chemical oxidation, and thus the acid formation continues. This

Jan 1, 1957

By L. W. Holm, G. G. Bernard

Laboratory experiments were conducted to determine the effect of foam on gas flow in porous media. Previous studies have indicated that foam may be applicable as a restrictive agent in influencing underground gas flow. Foam was found to be exceedingly effective in reducing the permeability of porous media to gas. Consolidated and unconsolidated sands with specific permeabilities of 100 to 146,000 md had, in the presence of foam, gas permeabilities that were less than 1 per cent of the specific permeability; in many cases the gas permeability was practically zero. Foam reduced the gas permeability of loose sand to a much greater degree than that of a tight sand. For example, the permeability of a 125,000-md sand was reduced to 3 md while the permeability of a 4,000-md sand was reduced to 7 md. This effect should cause, to some degree, selective plugging of high permeability channels in various oil displacement processes. The presence of oil in a porous medium decreased the effectiveness of foam in reducing gas permeability; apparently oil acts as a foam depressant. However, it was found that certain foaming agents were very effective in reducing permeability even. in the presence of oil. Also, continuous injection of other foaming agents increased their effectiveness, when oil was present. The effect of foam on permeability of porous media to gas was studied as a function of foaming agent concentration and injection rate, absolute permeability, total pressure, pressure gadient, length of porous system, brine concentration and time. INTRODUCTION The use of surface active agents in flood water to increase the recovery of oil has been studied in the laboratory and in the field for decades, with rather limited success. In recent years a new approach to the problem was proposed. Instead of using an aqueous solution of surfactant as an oil recovery agent, Bond and Holbrook2 proposed that the oil recovery agent be a mixture of surfactant solution and gas. In their method, a water-soluble surface active agent with foam-producing characteristics is injected into an underground formation as an aqueous slug. This slug is followed by gas to produce a foam within the rock. Foams are defined as "agglomerations of gas bubbles separated from each other by thin liquid films&apos;! A foam is fundamentally an unstable system. The foam process for oil recovery has since been studied by other investigators. Fried 1 has shown that foam can displace from porous structures oil that normally is unrecoverable by conventional water or gas drives. This superior oil displacing action is believed to be the result of several factors: (1) foam introduces into the reservoir many resilient interfaces of various sizes and curvatures, which increase the probability that a proper combination of forces for oil displacement will be created; (2) foam has appreciable viscosity which improves mobility ratio and contact efficiency; (3) foam accentuates the trapped gas effect because high gas saturations are possible without producing high gas/oil ratios. Deming4 studied the effect of various foam properties on the displacement of liquid. He found that (1) high foaming ability favors high displacement efficiency; (2) high foam stability is not necessary for high displacement efficiency; (3) displacement efficiency decreases with increase in plasticity of foam and (4) displacement efficiency is unaffected by surface tension of foaming agent solution. One of the important aspects of this oil recovery process is the effect of foam on gas permeability. The simultaneous flow of gas and liquid in porous media has been studied by numerous investigators and a large amount of literature exists on the subject. In this previous work, gas and liquid have generally been considered as essentially independent phases, whose flow characteristics are related through the saturation parameter. Foam, however, is a material with properties that are considerably different from those of its components; for example, the viscosity of a foam is greater than either of its components. Gas flow in a porous medium in the presence of foam should be considerably different

Jan 1, 1965

IN CIRCLES where mining men are wont to fraternize, a statement often heard is: "Yes, I spent six (or two, or ten, or thirty) years down at &apos;Chuqui.&apos; " This means Chuquicamata, the site in Chile of what in all probability is the world&apos;s largest deposit of copper ore. One hears similar remarks regarding Braden and Andes, and, in fact, regarding a score of other big mines in South America, Africa, and elsewhere, but Chuqui seems to lead the others as the locale of engineers who have done a stint in foreign countries. One reason probably is that it is the Anaconda Company&apos;s premier foreign operation. Because of its unusual size and the diversity of its operations a great many men are needed. It is a sort of training school for young engineers; but, also, Anaconda has sent down a great many mature members of its big organization for special assignments like metallurgical research or plant construction. Chuquicamata is about 150 miles northeast of Antofagasta, at an elevation of 9,500 ft. It is in an almost rainless desert country where the wind (it is alleged by some) blows most of the time. However, the copper mining entrepreneurs have done their best to make up for what nature has neglected to do in creating a pleasant environment for the people who operate the mines. These include about 160 "foreigners" of whom 86 are from the United States, most of them accompanied by their families. There are 165 Chileans on the staff. Comforts, conveniences, and many luxuries are provided to offset in some measure the disagreeable features of the climate. Nevertheless, as I have implied, engineers at Chuqui generally jump at the chance to become "alumni" when opportunity offers. At the same time, they appear to take pride in their alma mater.

Jan 1, 1957

By Helmer Hedstrom

GRAVITY surveying with the torsion balance or the pendulum for ore prospecting purposes has generally not been considered practical or even possible. It is the intention of this paper to show that a fast and sensi-tive gravimeter can be very useful in ore prospecting, as an auxiliary to the electrical and magnetic instruments. A number of gravimeters have been constructed and put in practical use in the last seven or eight years; for instance, by Ising, Lejay-Holweck, Haalck, Hartley, Thyssen, Noergaard, the Humble Oil and Refining Co. and the Gulf Production Co. Their main application, apart from their use for geodetic surveys, has been for structure mapping in oil prospecting. There is no record that any of them have been used for ore prospecting. About the middle of 1934 the Boliden Mining Co., in Sweden, began experiments in constructing a static gravity meter sensitive enough for ore prospecting. Calculations and considerations that will be discussed later in this paper showed that this would necessitate an accuracy in the measurements of 0.1 milligal-roughly, one ten-millionth part of the total force of gravity. The first successful practical field tests of the instrument were made in January 1936. About the middle of 1937 the Boliden gravimeter was perfected. Ore prospecting with this instru-ment is now regular practice in Sweden, especially for the testing of indications given by geoelectric and magnetic methods.

Jan 1, 1938

By J. H. Swisher

The solubility of sulfur and rate of solution of sulfur in pure Lron were measured in H2S + H2 and H2S + H2 H2O gas mixtures. The solubility and diffusivity of sulfur at 1410°Care 0.13 pet S and 1.0 x 10-5 sq cm per sec, respectively. The solubility iS the same, but the rate of sulfurization is slower in the presence of H2O in the reacting gas. Under these conditions, the over-all rate is controlled jointly by a slow surface reaction and by solid-state diffusion; the mechanism for the surface reaction has not been identified. KNOWLEDGE of the behavior of sulfur in solid iron is desirable for the metallurgy of such products as free machining steel, where a high sulfur level is required, and inclusion-free high-strength steels, where the sulfur specifications are very low. The present investigation was undertaken to check previously reported values for sulfur solubility and diffusivity in 6 iron, and to study the poisoning effect of chemisorbed oxygen on sulfurization kinetics in H2-H2S-H2O gas mixtures. All of the experiments were performed at 1410°C. The thermodynamic behavior of sulfur in 6 iron was the subject of a paper by Rosenqvist and Dunicz.&apos; The sulfur solubility at 1400" and 1500°C was determined by equilibrating pure iron specimens with H2-H2S gas mixtures. The maximum solubility of sulfur in 6 iron was alsc determined by Barloga, Bock, and parlee2 by reacting iron wires with sulfur in sealed capsules. In another investigation, the diffusion coefficient of sulfur in 6 iron at temperatures up to 1450°C was measured by Seibel.3 The method used was to measure sulfur concentration profiles in diffusion couples containing radioactive sulfur EXPERIMENTAL Apparatus. A vertical resistance furnace wound with molybdenum wire and containing a recrystallized alumina reaction rube was used for the experiments. The hot zone in the furnace was approximately 2 in. long with a temperature variation of ±3oC. The hot zone temperature was automatically controlled to within ±2°C, and the test temperature was measured with a pt/Pt-10 pet Rh thermocouple before and after each experiment. Flow rates of the reacting gases were obtained using capillary flow meters. Materials. The source of H2S in the gas train was a premixed cylinder containing 5 pet H2S in H2. This mixture then was diluted with additional hydrogen and argon. In some experiments, water vapor was introduced by passing hydrogen and argon through a column containing 10 pet anhydrous oxalic acid and 90 pet oxalic acid dihydrate. The vapor pressure of water above this mixture is well-known.4 Argon was used as a diluent to minimize thermal segregation of H2S in the furnace5 and to reach higher H2O:H2 ratios than could be obtained in mixtures of H2 and H2S alone. Argon was purified by passage over copper chips at 350°C and subsequently over anhydrone. Hydrogen was purified by passage over platinized asbestos at 450°C and then over anhydrone. The H2-H2S mixture was purified by passage over platinized asbestos and then over P2O5. The specimen stock was made by melting and vacuum-carbon deoxidizing electrolytic "Plastiron" in a zirconia crucible. The principal impurities are listed in Table I. In some of the equilibrium experiments, six-pass zone-refined iron was used to minimize impurity side effects. This zone-refined iron had a total impurity level of about 25 ppm. Procedure. Specimens were annealed in hydrogen for a period of at least 2 hr at the beginning of each experiment. The specimens were held in the reacting gas for times varying between 10 min and 17 hr, and cooled to room temperature in a water-cooled stainless-steel block at the bottom of the furnace. The pH2S/pH2 ratios reported are those for gas equilibrium at 1410°C. Calculations based on available thermodynamic data8 showed that the only other gaseous8 species that formed in significant amounts in the furnace were S2 and S. Even when water vapor was introduced into the gas mixture, the concentrations of SO2, SO, and so forth, were negligible. The initial partial pressure of H2S was therefore corrected for its partial dissociation to S2 and S in determining the equi-

Jan 1, 1968

By Donald O. Rausch, Adolph Soderberg

4.1-1. Introduction. Open pit mine planning must be correlated to all phases of a mining operation. The factors that must be considered in planning an open pit mine are numerous and must reflect the characteristics and surrounding conditions of a particular orebody. Therefore, only an outline of the subject can be presented here to aid the planning engineer in pointing out procedures that are generally applicable to pit design. The presentation is directed toward the planning of an open pit copper mine, but the procedures discussed should apply in most cases to any type of metallic or nonmetallic orebody. In planning an open pit mine the pertinent elements that must be included are: assays, geology, tonnage and areal extent of ore reserves, topography, mining equipment, economic factors of operating costs, capital expenditures, profit, types of ore, pit limits, cut-off grade, stripping ratio, rate of production, pit slopes, bench heights, road grades, ore metallurgical characteristics, hydrological conditions, property lines, and marketing considerations. 4.1-2. Sampling. Sampling must be adequate to classify the various materials to be removed from an open pit mine. Drillhole assays are plotted on sections and plan maps with ore and waste blocked out by selected bench intervals. These maps are prepared to depict the geological and other conditions existing on each mine level. The confidence factor to be applied to sampling and the resultant assays values must be given careful consideration. In uniformly disseminated de- posits, the confidence factor will approach unity. For widely fluctuating values, the average assay values should be discounted somewhat, the degree depending upon such factors as drillhole spacing. Such samples, at best, represent a very few pounds for hundreds to thousands of tons of ore

Jan 1, 1968

By W. H. Fulweiler

The writer would define the term "Use Classification" as a discussion of the qualities that coal should possess to fulfill the requirements of the industry or process in which it is to be used. The general problem of the gas industry is to transform the maximum amount of the thermal energy in coal into a gas of specified quality. The qualifications that a coal should possess to be useful in the gas industry are complicated by probably a greater number of factors than in most industries. The most important of these is the delivered price of the coal. While the- general problem of the industry is as given above, yet the actual problem is the production of gas of a specified quality at the minimum cost. The relative cost of coal and the selling prices for the residuals which are influenced to a large extent by geographical locations are of determining importance as effecting the cost of the gas. It is unfortunate that we cannot disassociate cost figures from a discussion of the desirable characteristics and this results frequently in the use of coal in one location that will be looked upon as quite impossible in another location more favorably situated. Without going into any discussion of the freight rate problem we might merely point out that in general the freight on the coal is equal to or greater than the mine price. It must be evident, therefore, that price must always be considered in any discussion of the effect of the characteristics of a given coal. Two Classes of PRocesses In discussing the characteristics of coals for use in the industry, we must divide the processes in use into two classes: (1) where the coal is destructively distilled at high temperatures resulting in the formation of coke in the liberation of gas and by-products, and (2) where the coal is consumed by combustion in air or steam with a production of gas and by-products leaving only clinker as a residue. The Germans differentiate these two types of processes in their words"&apos; entgasung&apos;" and&apos;" vergasung."&apos; In the distillation processes, we have the effect of the coal on the yield of gas and its quality; the quantity and quality of coke; and the

Jan 1, 1930

By J. S. Pascover, S. V. Radcliffe

The structures and transformation temperatures of high-purity Fe-Cr alloys have been investigated as functions of composition (0 to 10 wt pct Cr) and rate of quenching from the high-temperature Y phase field (up to 40,000°C sec-1). The structures were chmacterized by transmission electron microscopy. The transformation temperatures for each alloy exhibited the progressive decrease to a constant value with increasing cooling rate which has been shown to be characteristic of several iron binary systems. The corresponding structures were found to become increasingly finer in scale with increasing cooling rate and solute content, but to remain essentially equiaxed in character. In all the materials except the high-purity iron and one of the alloys, an additional and lower transformation temperature than the constant value for the equiaxed structures was observed. The structures of specimens which transformed at these lower temperatures (only single thermal wrests were observed in any given run) were martensitic and consisted of arrays of fine ferrite laths which varied in size and morphology with changing solute content. The factors controlling the nature of these transformations are discussed. The composition dependence of the martensitic transformation temperature, ME, in Fe-Cr alloys together with those reported for other iron binary systems indicate that MB for pure iron is some 700°c, rather than the values of 550° and 760°C reported previously. This conclusion is further supported by the results of a compmison of the thermodynamics of mmtensite formation in several systems. ThE extensive investigations of the structures formed on athermal transformation in iron and its alloys have led to the characterization of several forms of martensitic or "military"1,2 transformations and, in addition, a "civilian7&apos; transformation to ferrite or "equiaxed a"* which occurs athermally and at a very high rate.374

Jan 1, 1969

By Joseph W. Roe, L. L. HEWES

A GRAPHIC solution of Kutter&apos;s formula for the flow of water has been worked out By Dr. L. I. Helves in connection with his course in Graphic Computations, given in the Sheffieild Scientific School, Yale University, which may be of interest to those who deal with canals, flumes and streams.

May 1, 1909

By R. W. Harper, M. C. Fuerstenau, J. D. Miller

Data were obtained with hematite with octyl hydroxamate and oleate as collectors to determine the mechanism of collector adsorption and also to establish the roles that conditioning time and temperature assume in this system. The presence of hydroxy complexes of iron are apparently necessary for chemisorption of collector to occur, and it appears as if extended conditioning times and elevated temperature promote greater dissolution of the mineral and hence greater concentrations of hydroxy complexes. Data were also collected with two natural hematitic ores. With one ore that was ground to 70% - 15u, an addition of 0.4 lb per ton hydrox-amate resulted in a final concentrate recovery of 86% at a grade of 64% iron. Satisfactory concentrate grade could not be obtained with fatty acid under these conditions. The effect of conditioning time prior to the addition of collector was also examined with another ore. When the ore was conditioned for 3 min, 19% of the iron was recovered in the concentrate at a grade of 67% Fe. With a conditioning time of 7 min, 73% of the iron reported to the concentrate at a grade of 62% Fe. These products were obtained with an addition of 0.2 lb per ton hydroxamate. This ore also responded well to flotation with fatty acid. The use of potassium octyl hydroxamate as a collector for iron oxide has been the subject of an earlier study.1 From this initial study, it was suspected that hydrolysis of surface ferric iron was involved in collector adsorption. More recent work in other systems has shown that slight mineral dissolution, followed by hydrolysis of cations common to the mineral lattice, is apparently necessary, and that adsorption of these hydroxy com- plexes probably occurs prior to the adsorption of collector. In view of these facts, work has been continued on the hydroxamate-hematite and oleate-hematite systems to gain better insight into the mechanisms of collector adsorption on iron oxide. Microflotation experiments in conjunction with infrared analysis were used in this regard. In addition it was felt necessary to establish more clearly the responses that can be obtained from natural ores when hydroxamate is used as collector as compared to those obtained when fatty acid is used. Experimental Materials and Techniques Pure potassium oleate, potassium octyl hydroxamate, synthesized from hydroxylamine hydrochloride and methyl octanoate, and a distilled Tall Oil were employed as collectors. Conductivity water was used in the

Jan 1, 1971

By Robert B. McCormick

WORLD WAR II has developed a use for the nonmetal mineral quartz crystal that was unknown in World War I. During the interim period of peace, experimental work in the radio field with the piezoelectric properties of quartz crystal resulted in the almost universal adoption of quartz-crystal radio oscillator plates to control frequency in radio broadcasting, police, commercial and amateur communications equipment. Telephone resonators and filters made from quartz crystal also were developed, which vastly improved the frequency control of long distance telephone circuits. EXPANSION OF THE INDUSTRY The sudden war demands of the armed services for radio equipment using quartz crystal for frequency control led to an unprecedented expansion of the manufacturing industry. It is estimated that the 1940 peacetime volume amounted to approximately $1,500,000, while today a vast new quartz-crystal industry supplies more than $150,000,000 worth of quartz oscillator plates to the Army and Navy each year. This demand has caused an enormous expansion not only of American manufacturing facilities but also of Brazilian mining output, virtually our only source of raw quartz crystal. Actual figures of imports and consumption cannot be cited, for security reasons, but certain comparisons have been made, which indicate the transformation of quartz crystal from a minor to a major nonmetal. Lends has shown that the value of quartz-crystal exports from Brazil is now about equal to that of phosphate rock produced domestically in 1941 and actually exceeds the combined value of crude feldspar, gypsum and fluorspar production in the United States in the same year. This great expansion under wartime pressure was not accomplished without some anxious moments, but all the demands of industry have been met and the Government has been able also to accumulate a substantial stock pile of material against future contingencies. INSPECTION AND GRADING OF QUARTZ CRYSTAL The swift growth of the quartz-oscillator industry necessitated the simultaneous evolution of methods and criteria for inspecting and grading quartz crystal. It has been found that, generally speaking, it is economically feasible to cut only crystals that are at least 30 per cent by volume free from major defects such as optical and electrical twinning, cracks and fractures. Blue needles, bubbles, "chuva" and other minor imperfections can be tolerated in the usable portion unless present in great excess. The present marketing system in use in both Brazil and the United States, as far as quality is concerned, depends solely on the "usability" of a crystal, which is defined in the Brazilian-American agreement2

Jan 1, 1945