Search Documents

By W. A. Tiller

The conventional techniques1 for determining the liquidus and solidus surfaces of an alloy system containing more than two components are extremely tedious to use and do not provide a complete picture of the equilibrium relations between solid and liquid alloys. These techniques are unable to yield "tie-line" information concerning solid and liquid phase equilibrium, a very important parameter in the solidification description of the liquid alloy and a very necessary parameter in the preparation of "zone-levelled" alloy crystals. The tie-line in a polycomponent system is analogous to the partition coefficient, k, in a binary system, it gives the composition of the solid, Cs, in equilibrium with a liquid of composition CL. That is, CS = kCL, where CL = [CO, c1,...Cn] denotes the concentrations of the n + 1 constituents, and k = [ko, kb ,...kon] denotes the gross partition coefficient for the elements between the two phases; thus, k is the tie-line in this system. To provide complete information concerning the two-phase equilibrium in a polycomponent system it is necessary to know both the liquidus surface and the gross partition coefficient. From these two the solidus surface is obtainable. The conventional techniques are unable to provide this information in other than a binary system so we must look elsewhere. In recent years considerable insight has been gained into the correct description of the liquid-solid transformation, 2,3 and controlled solidification experiments may now be designed to both facilitate and enhance equilibrium diagram studies. In the present paper consideration is given to two methods for obtaining the liquidus surface and the tie-lines in polycomponent systems. The methods to be described below deal with the solidification of an n + 1 constituent liquid alloy of initial composition [co, Co ,...Con], where the superscripts refer to the elements present and the Oth element is considered as the solvent in which the n solutes are dissolved. The general assumptions made in the treatment are the following: (i) the solid and the liquid at their interface are in equilibrium during the growth of the solid phase, (ii) there is no diffusion in the solid phase, and (iii) the liquid phase is completely mixed and is therefore homogeneous in concentration. METHOD I In this section a general experimental method will be described which, in principle, is capable of giving an exact description of the liquidus surface and tie-lines. Consider the unidirectional solidification of the liquid alloy specimens L cm in length (freezing either horizontally or vertically). Allow the sample to be frozen very slowly from one end, as indicated in Fig. 1, with complete mixing in the liquid, and then analyze the solid bar to determine its chemical constitution as a function of position, x, along the bar. Let Fig. 2 represent a possible distribution of the ith constituent along the bar. At the point x' the concentration of the ith constituent is C1/5(x'), and the average concentration of the rest of the bar between x' and L is given by C:(X' - L) where [ A(x) c1s(x)dx c1/s(x'-L) = f A(x) dx x * and A(X) is the cross-sectional area at x. In a similar manner. all the Cf(x' - L) may be determined. Thus, the gross artition coefficient k for liquid of composition [Cs(x - L),...Cs(X' - L)] is given by -ko= CUs')/Cos(x' - L)" k0 = csn{x')/cs(x'- L) During the freezing of a charge of length L, the liquid composition may vary over a wide segment of the phase diagram and the gross partition coefficient over this segment of the phase diagram may be determined from one, bar. Fig. 3 illustrates the magnitude of Cs(g)/C,' as a function of the fraction g of the bar which has Solidified.2 We can see that the concentration in the bar will vary over a range of about 15 wt pct for C,' = 10 wt pct and k0 = 0.5. It appears that 4 or 5 specimens would be adequate to study a simple binary eutectic phase diagram.

Jan 1, 1960

By Pedro G. Salmon

The broad general distinction between primary and secondary batteries lies in the fact that in the former the current is produced by the consumption of one or both of the elements composing the cell, while in the latter the elements retain their form as such, and merely pass from one state of chemical combination to another. Much has been said in condemnation and but little in praise of storage-batteries; yet, notwithstanding the severe criticisms passed upon them, the skepticism with which electricians have viewed them, and the ignorance with which they have been handled, they continue to push their way into use. Their manufacture has now become a well-defined and established industry.

Jan 1, 1890

By Roy R. Weil, John A. Dziubek

This paper discusses the use of computer modeling, data manipulation, and mapping of three multi-seam coal properties in the Appalachian coal basin. Each case history represents a slightly different application of computer usage for estimation of reserves and planning surface mine sequencing. This practical use of computers demonstrates the suitability of data processing for normal evaluation of coal properties.

Jan 1, 1983

By H. M. Fisher, R. E. Snow, S. C. Sun

SEVERAL constructive and fundamental studies have been made in the analysis of data obtained from experiments carried on with batch ball and rod mills. The operating characteristics of ball milling in small continuous circuits have also been appraised. It is from these analyses that some of the theories of comminution have been developed. Relatively few studies of continuous rod milling have added significantly to the fundamental concepts, because seldom have they yielded sufficiently consistent results. Perhaps they have been too limited in their scope. Careful control of the variables in batch grinding is simple compared with that encountered in a continuous operation. This factor alone has discouraged many investigators. Occasionally results of systematic changes made in industrial rod mill circuits have been published, but usually the data are sketchy and are restricted because of the unwieldiness of the equipment used. The work, in general, has not been comprehensive; nevertheless it has provided empirical relationships that have bridged the gap between postulate and practice so that by proper manipulation of formulae, a mill designer can anticipate mill size and power requirements.14 Although operating variables of a small continuous mill are not so easy to control as with the batch mill, with present day devices, and with careful experimental work, consistent results can be obtained. Nearly four years ago, in the Process Laboratory, Allis-Chalmers Mfg. Co. began a systematic study of the effects of several variables upon the performance of the pilot rod mill. A mill was built in the laboratory to provide the versatility required for the proposed study. It was constructed in sections so that it could be operated, with a few modifications, as a rod mill 30 in. x 8 ft or 30 in. x 4 ft. The discharge end of the shell was flanged so that either an end peripheral discharge or an overflow discharge could be installed. Thus the performance of at least four types of mills could be studied merely by changing the type of discharge or the length of the mill shell. The grinding experiments were designed so that a study could be made of the way in which the mill speed, feed rate, and pulp density influenced the performance of both overflow and end peripheral discharge rod mills. Four sets of experimental data were collected from the four mill arrangements. The mill in each set of experiments was fed at four rates of feed depending on the length of the mill, at four pulp densities, and at five percentages of critical speed. Electrical and mechanical controls were in- stalled to regulate all these independent variables, and auxiliary devices were used to verify the precision of the controls at each point. The dependent variables used to quantify the experiments were the reduction ratio and the hew surface area produced as calculated from sieve analyses. These were incorporated with the energy factor by the calculation of both the new surface produced per unit of energy and the Bond work index.' Rod wear, as a dependent variable, was not studied because of the short period of operation for each run. Exclusive of repeat runs, each set of experiments yielded 80 products, and the total study at least 320 products, all of which were quantified. With the operating information collected, these data presented a bewildering accumulation. Statistical analysis has been invaluable in unraveling the confusion and in presenting a means of establishing the nature and the magnitude of the significant variables. Data presented in this paper are those from the 30 in. x 4 ft end peripheral discharge rod mill, Fig. 1, when limestone was ground at feed rates of 1000, 2000, 4000, and 5000 lb per hr, at pulp densities of 50, 60, 70, and 80 pct solids, and at mill speeds of 50, 60, 70, 80, and 90 pct of the critical speed. These 80 tests have all been run at least twice, and occasionally a third time, to prove that the data obtained were reproducible. The techniques of operation and the methods of quantification of results are described in the following pages and the results analyzed statistically to show the significant variables. The variables are plotted to show the relationships that exist. A massive dolomitic limestone from Waukesha Lime and Stone Co. was used for feed during these experiments because of its availability and its tex-tural uniformity. This limestone analyzed 28.7 pct CaO, 21.0 pct MgO, 6.0 pct SiO2, 0.4 pct A1²O³, and 0.3 pct Fe²O³ and had a loss on ignition of 44.1 pct. It had a rod mill grindability at 14 mesh of 9.6 grams per revolution from which a work index of 13.9 was calculated. The ball mill grindability at

Jan 1, 1955

By Richard D. Hagni

Although the ore microscopist routinely examines polished sections to determine the mineralogy and texture of ores, his importance to the solution of problems peripheral to geology is not always fully realized. The techniques which he uses can be applied with little modification to the solution of a wide variety of beneficiation problem. By extending his studies beyond those normally considered to be of interest to the geologist, he can include examinations of polished sections of selected mill products. This is a logical extension, because the minerals and textures in the polished sections of ores are the same as those in millproducts. The mill dressing engineer should be more aware of the types of beneficiation problem that can be solved by the ore microscopist and what the ore microscopist can do for him. A greater degree of cooperation between the ore microscopist and the mill dressing engineer can be of significant mutual benefit. Ore microscopy holds an advantage over chemical analysis, because the interrelations and combinations ofthe mineral constituents of an ore or mill product can be visually determined. This advantage provides solutions to many beneficiation problem. Locking is a type of beneficiation problem that is particularly amenable to ore microscopy. The percentage, type, and distribution of locked particles can be readily determined with the aid of an ore microscope and an estimate made of the extent of additional grinding required for liberation. The extent of intimately locked types, which no reasonable amount of grinding will liberate, can also be evaluated. Mineral coating conditions, free particles of a deleterious mineral, and free particles of a valuable mineral held in flocculated clusters of gangue are other features that can readily be observed. In some instances, visual examination may show that the problem is not one of locking. Photomicrographs illustrate the variety of beneficiation problems for which the ore microscope is applicable. These problems and their resolution demonstrate the importance of the instrument and show the value of close coordination between the mill dressing engineer and the ore microscopist.

Jan 1, 1979

By R. D. Gibbs, C. C. Taylor

The gas-lift, or circulation of gas for the production of crude oil, now includes the gas operator in field production activities to a greater extent than ever before. It is the purpose of this paper to show the scope of his activities and to discuss the various means of handling and treating the large quantities of gas which are now of a somewhat different nature than formerly. The extent of the stripping action of circulating gas on oil must be discussed, as this can be governed somewhat by the method of treatment of the recirculated gas. Change in Gas-decline Curve under Circulation Before the advent of the gas-lift, the gas-production curve of a field showed a peak during the flush production with a rapid decline as the wells were put on the pump and then a long steady decline curve of a relatively small volume of rich gas for the life of the field. Under the gas-lift method of production, instead of having the sharp decline at the end of the flush production period, sufficient circulating gas to keep up the required total gas-oil ratio would be turned to the wells. The gas-production curve then assumes a long gradual decline, giving a large volume of gas for treatment for several years to come. The gas-decline curve will not follow that of the oil, as the lowering of the rock pressure by the steady production of oil and gas from the sand will make it necessary to continue using the large tubing and to circulate large volumes of gas in order to keep the back-pressure against the sands as low as possible. A Complicated Distributing System In tracing the flow of the gas from the time it leaves the well until it again enters through the casinghead, under high pressure, we get a very good idea of the complex distributing and regulating system that must be installed and the large treating and compression plants that are necessary (see Fig. I). Gas traps must be large enough to efficiently separate large quantities of gas and oil and should be elevated sufficiently to enable the oil, if

Jan 1, 1928

By Henry D. Hibbard

At the beginning of a Henry M. Howe lecture it seems fitting to refer to Howe's great contributions to steel metallurgy, and particularly to the literature thereof. Most of my predecessors in this role have been able, from their association with him, to give direct testimony as to his great services; but although connected with him for years in a business way, I am less familiar with what might be called his academic side, except as it is embodied in his utterances, written and oral. Howe was adept in his genial way in extracting information in any line which, at the time, was of interest to him. In a technical lecture one expects as a rule new knowledge—something about recent advances relating to the subject. On this occasion, however, I will ask you to go back with me to the primary department of steel lore, as the title of my lecture shows, to review the more fundamental features in that field for the purpose of seeking some gaps which we can fill and so give the subject renewed interest. In thus going back one must inevitably repeat many familiar facts, but that seems to be necessary in order to reach a clear understanding of the unrecorded matters. The full interpretation of a steel analysis is at present unattainable, though much progress toward that end has been made. The ultimate analysis, giving the percentages of the five commonly determined elements, does indeed usually give a fair idea of what the steel is, and is ordinarily enough, with knowledge of its history and physical condition, to enable it to be assigned to some purpose or use for which it is reasonably suitable. But discrepancies arise. Every maker and every user of steel knows, from at least occasional examples in his own experience, that the ultimate analysis is insufficient by itself to enable one to tell positively, from its interpretation, either the mechanical properties of the steel or its adaptability to the purpose for which it was made. Further, if, while having the specified composition, it is abnormal or unsatisfactory, why it is so. Good, bad and indifferent steels may have substantially the same ultimate analysis.

By J. D. Raulerson, J. M. Williams

This paper presents a comparative evaluation of several system currently being used or proposed for the transport of matrix from an open-pit mine to a large fixed plant. The matrix is a sticky, wet clay to be carried from 8-16 km (3-10 miles) at 910 t/h to 1.8 kt /h (1,008-2,000 stph). The system is complicated by frequent moves of the open-pit mine site and other factors, such as use of the clay component in land reclamation.

Jan 1, 1984

By F. C. Bond

SIZE of grinding media is one of the principal factors affecting efficiency and capacity of tumbling-type grinding mills. It is best determined for any particular installation by lengthy plant tests with carefully kept records. However, a method of calculating the proper sizes, based on correct theoretical principles and tested by experience, can be very helpful, both for new installations and for guiding existing operations. As a general principle, the proper size of the make-up grinding balls added to an operating mill is the size that will just break the largest feed particles. If the balls are too large the number of breaking contacts will be reduced and grinding capacity will suffer. Moreover, the amount of extreme fines produced by each contact will be increased, and size distribution of the ground product may be adversely affected. If the balls added are too small, grinding efficiency is decreased by wasted contacts that are too weak to break the particles nipped; these largest particles are gradually worn down in the mill by the progressive breakage of corners and edges. Ball rationing is the regular addition of make-up balls of more than one size. The largest balls added are aimed at the largest and hardest particles. However, the contacts are governed entirely by chance, and the probability of inefficient contacts of large balls with small particles, and of small balls with large particles, is as great as the desired contact of large balls with large particles. Ball rationing should be considered an adjunct or secondary modification of the principle of selecting the make-up ball size to break the largest particle present. Empirical Equation In 19521,2 the author presented the following emerical equation for the make-up ball size: B - ball, rod, or pebble diameter in inches. F = size in microns 80 pct of new feed passes. Wi - work index at the feed size F. Cs - percentage of mill critical speed. S — specific gravity of material being ground. D == mill diameter in feet inside liners. K - 200 for balls, 300 for rods, 100 for silica pebbles. Eq. 1 was derived by selecting the factors that apparently should influence make-up ball size selection and by considering plant experience with each factor. Even though Eq. 1 is completely empirical, it has been generally successful in selecting the proper size of make-up balls for specific operations. But an equation based on theoretical considerations should be used with more confidence and have wider application. The theoretical influence of each of the governing factors listed under Eq. 1 was accordingly considered in detail, as described below, and a theoretical equation for make-up ball sizes was derived. Derivation of Theoretical Equation Ball Size and Feed Size: The basis of this analysis is that the largest ball in a mill should be just sufficient to break the largest feed particle into several pieces, excluding occasional pieces of tramp oversize. In this article the size F which 80 pct passes is considered the criterion of the effective maximum particle feed size. The smallest dimension of the largest particles present controls their breaking strength. This dimension is approximately equal to F. As a starting point for the analysis it is assumed that a 1-in. steel ball will effectively grind material with 80 pct passing 1 mm, or with F- 1000µ or about 16 mesh. The breaking force exerted by a ball varies with its weight, or as the cube of its diameter R. The force in pounds per square inch required to break a particle varies as its cross-sectional area, or as its diameter squared. It follows that when a 1-in. ball breaks a 1-mm particle, a 2-in. ball will break a 4-mm particle, and a 3-in. ball a 9-mm particle. This is in accordance with practical experience, as well as being theoretically correct. Confirmation of this reasoning is supplied by the Third Theory of Comminution," which states that the work necessary to break a particle of diameter F varies as F. Since work equals force times distance, and the distance of deformation before breaka4e varies as F it follolvs that the breaking force should vary as F½ These relationships are expressed in Table I, with a 1-in. ball representing one unit of force and breaking a 1-mm particle. This establishes theoretically the general rule used in Eq. 1 that the ball size should vary as the square root of the particle size to be broken. Ball Size and Work Index: The work input W required per ton" varies as the work index Wi, and the

Jan 1, 1959

By J. F. Cuderman

A technique using propellants has been developed for producing multiple fractures about a wellbore. The use of propellants having a range of burn rates permits precise control of combustion gas release and thereby of borehole pressurization. The pressure rise- time is the key variable governing fracture behavior. The peak pressure attained is of secondary importance and appears to be a function of in situ stress and loading rate. The fracture geometry is governed by the in situ stresses and pressure risetimes. The major fractures occur along the principal planes of stress and along apparent planes of maximum shear stress.

Jan 1, 1984

By William Kent

In the paper by Mr. Fernom, on Red Charcoal, read at the first session of this meeting, it was suggested that this fuel might be used in the blast furnace with greater economy than ordinary or black charcoal. In the discussion which followed the paper, it was stated that the charcoal furnaces of the Lake Superior District have used imperfectly burned charcoal with success, and that these furnaces have given the best results in fuel economy on record. On consulting some of our well-known metallurgical authorities the writer finds that the question of the use of red charcoal, or other imperfectly burned charcoal, or charred wood, is not at all new. In Percy's late work on Fuel, pages 409-414, are given a few facts, which are here condensed, as follows:

Jan 1, 1879

By K. Winterton

The effect of a near-saturation unidirectional magnetic field was to decrease slightly the endurance life in Armco iron in the annealed condition. This is expected since the energy-absorbing mechanism associated with domain wall movemenfs is inhibited bv the strong field. THE factors determining failure under dynamic loading are not yet clearly recognized. One of the properties of a metal which might be thought to influence fatigue life is its damping capacity. Foppl1 conducted an alternating torsion test at a frequency of 700 cpm continuously for a period of 3 years, without the test piece breaking or showing any sign of deterioration after 1100 Million cycles of stress; the rate of dissipation of energy was sufficient to maintain the test piece at about 100°C above the ambient temperature. cazaud2 concludes from this, and others follow him, that ('the capacity for dissipation in the form of heat by internal damping is unlimited" and that therefore "damping is not directly related with fracture by fatigue." Future work may necessitate qualification of this rather uncompromising view. It is shown later that in all

Jan 1, 1960

By E. V. Potter

For a nurnber of years, it has been known that manganese made by electro-deposition under certain conditions is ductile while under other conditions it is very brittle. The ductile metal is gamma manganese normally stable only between 1100 and 1138°C1; the brittle metal is alpha manganese, stable up to 727OC. The ductile metal is not stable, but gradually changes to the brittle form; the time required to complete the transfornlation is about 20 days at room temperature. Other observations have indicated that the transformation is completed in 10 to 15 min. at about 125°C, while at — 10°C, no appreciable change occurs in 9 months. The properties of gainma and alpha Illanganese in the pure state are ordinarilj difficult to determine because the gamma structure cannot be retained by normal quenching procedures and alpha manganese is so brittle, it is difficult to obtain specimens free from flaws. In a recent investigation2 some properties of gamma and alpha manganese were determined by studying the ductile electrolytic metal and determining the changes in its properties as it transformed to the brittle alpha form. These investigations provided an excellent opportunity for following the progress of the transition and studying its mechanism. The results of a series of such investigations are reported in this paper. Procedure Various properties of manganese were determined starting with the metal in the original ductile gamma form and following the subsequent changes in its properties as the metal transformed to the brittle alpha form. These observations were made at various temperatures, the data providing information regartling the mechanism of the transformation as well as the effect of temperature 011 the transition rate. Structure and resistivity values gave the most significant results, so this paper is concerned primarily with them. The structure was studied microscopically as well as by X ray diffraction. The resistivity was determined on strips of the metal by measuring the potential drop across a given length of the specimen. Current was passed through the specimen by wires soldered to its ends, and the potential connections were made by wires looped around the specimen near its center. The current was determined by the potential drop across a standard resistor connected in series with the specimen, the potential drop being measured on a potentiometer. In the temperature range from room temperature to 100°C an ordinary drying oven was used to heat the specimen. This was entirely satisfactory except at 100°C, where the time required to heat the specimen was long compared to the transition time, making the initial section of the resistivity curve unsatisfactory. To overcome this limitation, at 100°C and higher a thermostatically controlled oil bath was used to heat the specimens. The block on which the specimen was mountetl was plunged into the hot oil at the start of each test. The heating time was thereby reduced from 5 min. to about 6 sec, and dependable resistivity values could be obtained through 160°C. At this point the whole transition, including the warm-up time for the specimen, required only about 20 sec and it was not considered worth while trying to extend the temperature range further. Aside from the heating problem, the problem of making a sufficient number of accurate resistivity determinations became more and more difficult as the temperature was raised. Using the manually operated potentiometer, 100°C was about as far as it was possible to go. At this temperature and above, a self-balancing photoelectric recording potentiometer was used. Its response was quite rapid, and it proved to be entirely satisfactory all the way through 160°C, where the tests were stopped because of the specimen heating problem rather than any limitation of the potentiometer recorder. The metal used in these tests was prepared at the Salt Lake City laboratory of the Bureau of Mines. The method of preparation is discussed in a paper by Schlain and Prater.3 The sheets were about 2 3/8 by 5 3/16 in. and varied from 10 to 16 mils in thickness. They could be cut readily into pieces suitable for the various tests. X ray and microstructure determinations were made on pieces about 1/8 to 1/4 in. wide and about 1 in. long, while resistivity measurements were made on strips as long as possible and about 55 in. wide. The thickness of each sheet was not uniform over all its surface. This had no bearing on the X ray and microstructure determinations, but sections as nearly uniform and free from flaws as possible were chosen for the resistivity determinations. The gamma manganese was electro-deposited at 30°C, the time of deposition ranging from 5 to 12 hr for each sheet. Whenever possible, the tests were started directly after the metal was stripped from the cathode; otherwise the sheet was placed immediately

Jan 1, 1950

By J. C. Wright

A practical program of education for workers of the mining industries is being formulated by the Federal Board for Vocational Education in cooperation with the states in which this industry is a dominant one. The Federal Government last year passed a law, known as the Federal Vocational Education Act, that provides for the promotion of vocational education and for cooperation with the states in the promotion of such education in agriculture and trades and industries and in the preparation of teachers of vocational subjects. More than 1,000,000 men in the continental United States are employed in mines and quarries. The following table, from the 1910 Census Report, shows the relative importance of mining and manufacturing pursuits: Manfactures Mines and quaRRies Employees.......... 7,405,313 1,109,410 Capital............. $18,428,269,706 53,380,525,841 Value of product..... $20,672,051,870 $1,238,410,322 Of the more than 1,000,000 men employed in mining, almost three-fourths are engaged in the production of bituminous and anthracite coal; one-fifth, in the production of copper, iron, lead, zinc, and other metals; and the remainder in getting out structural and miscellaneous materials from quarries. The meeting of the needs of the coal-mining industry, therefore, is the problem of greatest importance in the point of numbers to be served. Moreover, the dangers in coal mining are greater than in metal mining. Practically all states have set up educational and technical standards for the position of foreman, boss, superintendent, etc., and every applicant for these positions must have a certificate of competency. The qualifications, too, are becoming increasingly difficult in the field of technical information. In some states, every miner must have a certificate, which is issued by the mine examining board only after an oral examination. Did these state laws not call for definite and comprehensive plans for the vocational education of men in the mining regions, the conditions

Jan 1, 1919

By Frederic Benard

PRIoR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company's smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow- • gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of transferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 1 1/4 miles. Although common in steel practice, the transportation of blister copper in this form had not previoisly been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended on the design and combination used for the particular experiment. The vessel was filled with approximately 2 1/2 tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack on refractories. From the information derived, and in consultation with the engineering staff of the supplying company, an order was placed for the first

Jan 1, 1944

By W. H. Herrnstein, J. B. Clark, E. C. Utley, A. J. McEvily

The ratio of the endurance limit (10' cycles) to tensile strength of age-hardened aluminum alloys is approximately 0.3, whereas the ratio for annealed alloys is about 0.5. The lower value for the age-hardened alloys has been associated with the instability of coherent precipitate during cyclic loading, but it has not been definitely established whether this instability is due to overaging or reversion during cyclic loading. The results of the present investigatzon support the reversion viewpoint. In this work specimem of 2024-T4 aluminum alloy were aged for 16 hr at 150°C after cycling for 10 pct of the life at 25.000 psi. These specimens were then tested to failure and exhibzted a marked increase in fatigue life. It is proposed that during the early stages of fatigue in this alloy dislocations cut through the coherent precipitate and bring about the reversion of the precipitate. Subsequent aging at 150ºC induces reprecipitation in the precipitate-free zones so that the weakened regions are strengthened and the fatigue life is extended. It Is recognized that the fatigue strengths of precipitation hardened aluminum alloys are unusually low relative to their tensile strength.'-= This feature is illustrated in Fig. 1 where it can be seen that age-hardened alloys have lower fatigue ratios (the ratio of the fatigue strength to the tensile strength) than those in the annealed or cold worked state. Further, as shown in Fig. 2, the more an alloy is dependent upon precipitation hardening for its total strength, the lower is the ratio of the fatigue strength to the tensile strength. This state of affairs has been associated with an instability of the metastable metallurgical structure of precipitation hardened aluminum alloys during cyclic loading. Evidence2 in support of this view is that the fatigue ratio increases in these alloys as the test temperature is lowered, thereby indicating that thermo-mechanical instability, rather than some other factor such as a non-uniform distribution of precipitate, is the factor responsible for the low fatigue ratio at room temperature. Two mutually exclusive proposals have been ad- vanced to account for this instability. Hanstock has proposed that overaging takes place during cyclic loading, and in support of this view, Broom et a1.2 have indicated that an overaging process might be promoted by the large numbers of vacancies which are created during cyclic loading. The creation of vacancies by radiation4 has been shown to lead to rapid overaging. Hanstockl obtained visual evidence of overaging in an aluminum alloy after cyclic loading, but in this instance it has been pointed ou? that because of the high frequency used (60,000 cpm) the observed effect may have been due to normal high temperature precipitation around energy dissipating cracks. Efforts to discern visual evidence of overaging in this alloy at lower test frequencies were not successful.3 The alternative postulate3 is that reversion takes place during cyclic loading and leads to localized soft spots at which fatigue cracks are readily initiated. Evidence for this process has recently been provided by Polmear and Bainbridge5 who demonstrated metallographically that regions depleted of precipitate were created during cyclic loading of an aluminum alloy. Inasmuch as precipitate particles bordering the depleted region had not grown in size, it was concluded that the solute atoms which had constituted the missing particles had gone back into solution. No mechanism for the reversion process was presented. The present study was undertaken to investigate further the conditions leading to instability during cyclic loading, and to determine whether reversion or overaging had taken place as a result of cyclic loading. BACKGROUND AND TEST PROCEDURE In order to differentiate between the processes of reversion and overaging, rest periods at an elevated temperature, which ordinarily would insure additional precipitation, were used in this investigation. It was expected that after a period of cyclic loading an elevated temperature rest period would result in a decrease in the remaining life of the specimen if overaging were occurring during cyclic loading, whereas in the case of reversion, reprecipitation would occur and the fatigue life would be extended. Such an expectation is based on the assumption that the crack-nucleation phase is a significant portion of the total fatigue life, and that such a treatment is of influence in the crack-nucleation stage and is relatively unimportant thereafter.

Jan 1, 1963

By R. R. Hartman, W. B. Agocs

IN the course of a return flight from Olympia, Wash., to Laramie, Wyo., an airborne magnetometer profile was recorded continuously. The level of flight was controlled at barometric levels along segments of the flight. Barometric altitude was changed from 3000 ft to a maximum of 12,000 ft above mean sea level to take care of topographic variations. Terrain clearance varied from 800 to 7300 ft. Horizontal positions were obtained by recording and tying to cities, towns, airports, river crossings, and other landmarks in the course of the flight. Figs. 1-6 show the course of the flight and the general geologic and tectonic features traversed. The flight line begins south of Olympia, Wash., and proceeds south across the Puget-Willemette depression to the Columbia River. Thence it proceeds eastward along the Washington-Oregon border across the Cascade Mts. and lava flows and the Umatilla basin to Pendleton, Ore. From Pendleton it traverses the Blue Mts. uplift of Oregon in a southeasterly direction, and then to the Boise basin of southwestern Idaho. The flight line swings in an easterly direction as it passes over the Snake River downwarp to the south of the Idaho batholith. It then passes over the northern portion of the Great Basin and the heavily overthrust area at the intersection of the Utah, Idaho, and Wyoming borders. The flight then assumes an easterly course to cross the series of basins and uplifts of southern Wyoming and terminates near the western flank of the Laramie uplift. It should be clearly understood that all statements in this article pertaining to the magnetics were interpreted on the assumption of elongate anomalies transverse to a single profile. Hence any theories or ideas advanced here are in line with future paths of research rather than trying to prove or disprove existing data. Magnetic Interpretation: Depth determinations were made by the slope method of Peters: which is stated as follows: "Draw a line in the maximum slope (at the point of inflection); draw a line whose slope is one-half this maximum slope; draw two lines parallel to this line tangent to the anomaly curve. The horizontal distance between the points of tangency is approximately equal to 1.6 times the depth [or the distance times 0.6251." Certain assumptions must be made for determinations of the causes of the magnetic anomalies:' 1) The anomaly is caused by a susceptibility change rather than basement relief. 2) Polarization of the basement rocks is in the same direction as the earth's inducing field. 3) The disturbing magnetic mass has a great horizontal length in comparison to its width and its sides are vertical and of great vertical extent. 4) The anomaly is unique and not affected by the anomalies from nearby sources.

Jan 1, 1957