Search Documents

By J. Szekely, P. Tarassoff, N. J. Themelis

In a copper converter air enters the bath in the form of turbulent jets. The interaction of these jets with the molten matte is fundamental to the converting process. In the present study, an equation is derived to describe the trajectory of a gas jet in a liquid. Calculated and experimental results for air jets injected into water are in good agreement. The trajectories of air jets in copper matte are predicted. THE air injected through the tuyeres of a Peirce-Smith copper converter emerges into the bath of molten matte in the form of a highly turbulent jet. The air jets affect a number of chemical and physical processes occurring in the converter: i) Converting Rate. It is generally recognized that the production capacity of a converter is limited by the flow of air which can be injected through the tuyeres and by the oxygen efficiency. In turn, the air flow is limited by pressure drop considerations or by the amount of splashing within the converter. ii) Oxygen Efficiency. This depends on the dispersion of the air jet in the liquid bath, and its trajectory through the bath. iii) Mixing. The jets act as mixing devices by transferring momentum energy to the bath; in this way the heat generated by the converting reactions occurring in the jets is distributed through the bath. iv) Refractory Wear. The proximity of the jets, which are centers of heat generation, to the refractories in the tuyere zone may have an important effect on refractory life. Mixing conditions in the bath will also influence refractory erosion. v) Splashing, and Accretion Build-Up. The energy of the jets is not dissipated entirely in mixing the bath. particles of liquid are carried out kith the gas above the surface of the bath in the form of liquid spouts and droplets. These result in the undesirable build-up of accretions on the converter mouth, and dust losses in the flue gas. Despite the importance of the interaction of the air jets and the matte in a converter, very few studies of the fluid dynamics of converting have been reported in the literature. Metallurgists in the USSR appear to have been more concerned with the subject than their Western counterparts. Deev et al.1 studied the interaction of an air jet with aqueous solutions in a converter model and qualitatively determined the tuyere air velocity and tuyere inclination which produced the most favorable results with respect to good mixing in the bath, and minimum splashing. Shalygin and Meyer-ovich2 also examined the air-matte physical interaction both in models and in industrial converters; they concluded that in conventional converting practice, there was no significant penetration of the air jets into the matte layer, and consequently the converting reactions occurred mainly in a zone adjacent to the tuyeres. The behavior of air jets in a converter bath, and the aerodynamic characteristics of tuyeres are discussed at length in a monograph on converting by Shalygin.3 However, the description of the phenomena occurring in the converter bath is largely qualitative. The side-blown Bessemer converter for steelmak-ing is very similar to the Peirce-Smith copper converter. Among the few investigations of the behavior of air jets in the bath of a Bessemer converter are those of Kootz and Gille4 who studied splashing in the course of an investigation on the effect of blowing conditions and converter shape on nitrogen pick-up in Bessemer steel. They found that during blowing standing waves were formed on the surface of the bath; the amplitude of the waves increased with the depth and angle of tuyere immersion until the whole bath moved backwards and forwards causing heavy splashing. Kazanstev5 used a model of a Bessemer converter to obtain correlations between the axial velocity of a gas jet and distance from the tuyere orifice and the Froude number of the jet. shalygin3 used these results to calculate the horizontal penetration of an air jet in a copper converter; the penetration was defined as the distance in which the axial jet velocity decreased to 10 pct of its initial value. However, the rising trajectory of the jet was not taken into account. In the absence of quantitative information on the fluid dynamics of converting, the design of copper converters has been based mainly on operating experience. Such experience tends to vary widely from smelter to smelter., This is reflected in Table I which is based on data compiled by Lathe and Hodnett.6 Aside from a rough, and perhaps obvious correlation between the total air flow and converter volume, Fig. 1, no pattern emerges from the data. For example, tuyere throat air velocities vary from 215 to 465 ft per sec in converters of the same size, for little apparent reason. The air jet energy input per cubic foot of converter volume, which may be taken as a measure of the amount of mixing in the converter bath, also varies greatly. A recent analysis of converter data by Milliken and Hofinger7 has also revealed unexplained variations in operating parameters. It is believed that by gaining a better understanding of the fluid dynamics of converting a more rational basis may be provided for the design of converters. In particular, it is proposed that if one takes into account the desirable criteria of a high converting rate, high oxygen efficiency and long refractory life, there should be an optimum configuration of tuyere air flow for a converter of a given diameter. The present investigation is concerned with the form and trajectory of an air jet in a converter bath. The general theory of turbulent jets has been expounded by Schlichting8 and Abramovich.9 However, most experi-

Jan 1, 1970

By Russell C. Flemming

The aim of this Source Book has been to bring together in concise form information on the wealth of technical literature on mining and geology issued by the bewilderingly many state bureaus, federal bureaus, technical societies, trade associations and other noncommercial agencies in the United States. The effort has been made to include the navies of all the noncommercial publishers of such technical literature, to indicate where and at what price the articles may be obtained, as well as to give with as much detail as space permits specific information on individual papers. The thought has been to put the information particularly in the hands of the younger members of the profession, who may not yet have had the wide contacts with this literature that they will need in later life. Several factors have interfered with the complete attainment of the original intention. Undoubtedly some agencies that properly have a place in these pages have unintentionally been omitted; many agencies canvassed were omitted as not having literature of direct concern here; in other cases some. of the needed information was lacking; and the limitations of time and space have bounded the scope of the compilation.. Except in one or two cases, only publications prior to July, 1932, are included here, and from that standpoint the book is necessarily incomplete, as additions are continually being made to the files of literature on these subjects. Individual titles have been listed whenever possible but where an agency has collected a great mass of published material only most important titles, and a general review of the scope of the works, can be made. This results in penalizing, in a way, bureaus such as the U. S. Bureau of Mines and the U. S. Geological Survey, which have voluminous and vitally important works in the fields covered, because space commensurate with that volume and importance cannot be allowed. In any event, in such cases, a complete catalog is issued periodically and repetition is superfluous. The space

Jan 1, 1933

By M. C. Fuerstenau, J. D. Miller

The response of calcite to flotation with saturated fatty acids and alkyl sulfonates of various chain lengths is presented. The amount of collector re-quired for flotation is shown to decrease systemati-cally with increasing carbon content from 8 to 12-carbon atoms per molecule. This systematic flotation response is correlated with the solubilities of the calcium-collector salts, which were established with a nephelometer. The 14-carbon collectors deviate from this systematic behavior, and no flotation is possible with the 16-carbon homologs. As determined by infrared analysis, the mechanism of collector adsorption involves a specific chemical reaction be-tween the collector and the surface. A reaction of the form CaCO3(s)+ 2 RCOO"=*=Ca(RCOO)2(s) + C03= is suggested. The pH of the system is also shown to be a most important parameter as it controls the carbonate, calcium, and collector ion concentrations in solution and thus controls flotation response. The importance of hydrocarbon chain length of collectors was recognized early, and various studies have been made on this aspect of flotation. Wilkinson, ' for example, noted that as the chain length of alkyl xanthates is increased, the amount of collector required for flotation of sphalerite is decreased. The same effect has been shown in the flotation of galena.2 Similar results were obtained when malachite3 and calcite4 were floated with various fatty acids. DeBruyn5 has shown that a similar phenomenon occurs when quartz is floated with amines at constant pH. Recently, Fuerstenau, Healy, and Somasundaran6 correlated this phenomenon with the van der Waals cohesive free energy of association of the hydrocarbon chains. It seems unlikely, however, that chain association could be involved in the sulfide and carbonate systems with the collector additions employed, especially with the short-chain xanthates. Rather, it would seem that the decrease in collector concentration with increase in chain length noted for flotation is related to the solubility of the metal-collector salt. The purpose of this investigation is to verify this premise and also quantify this phenomenon if possible. Calcite was selected for study with both alkyl sulfonates and saturated fatty acids as collectors. EXPERIMENTAL MATERIALS AND METHODS The collectors used in this investigation ranged from 8 through 14 carbon atoms per molecule. The fatty acids had a reported purity of greater than 99%. The sodium alkyl sulfonates were provided by the Marathon Oil Cot, Littleton, Colorado, and had the

Jan 1, 1968

By A. R. Kinkel

The Shasta copper-zinc district of northern California lies in the foothills of the Klamath Mountains at the northern end of the Sacramento Valley. It contains two main areas of base-metal ore deposits, the East Shasta and West Shasta districts shown in Fig. 1. The East Shasta includes the area from the Afterthought mine, near the settlement of Ingot on U. S. highway 299 East, to the Bully Hill mine, on the north side of the Pit River, 9 miles to the north- west. The West Shasta, a well-defined northeast- trending district about 8 miles long and 2 miles wide, west of the Sacramento River, Fig. 2, is the western part of the ore-bearing area formerly known as the Shasta copper belt. Referred to in the older writings as a copper arc, this belt was thought to form a crescent extending entirely around the head of the Sacramento Valley, the convex side to the north. Recent studies by the U. S. Geological Survey in cooperation with the California State Division of Mines show that there are two districts, one at each end of the so-called copper arc, which are distinct in geologic structure and ore occurrences, and that there is only sporadic and unconnected copper mineralization between them.

Jan 2, 1955

MEETING OF SAN FRANCISCO SECTION Twenty members were present at the meeting of the San Francisco Section, May 20, 1919. Chairman Bradley being in Alaska, vice-chairman, T. A. Rickard, presided. Prof. Frank H. Probert gave a short account of the activities of the governmental commission, consisting of himself, George S. Rice, and F. G. Cottrell, which recently visited Europe, and studied the coal, iron, salt, and chemical industries. When the work is finished reports will he issued. He gave a resume of the history of. the changes in nationality of Alsace-Lorraine and 'described the importance of the region for coal, iron, and potash. With the return of these provinces France will have an annual output of more iron ore than she has coke to smelt it with; hence, the importance of the Saar coal field. With these new mines France will take the predominant position in the iron and steel-industry formerly held by Germany. Many details were given of the devastated mines of France, and of their former value, production and the destruction that overtook them. Noteworthy is it that much of the damage was done as late as Oct. 28, 1918, for the express purpose of ruining the country industrially. The damaged area of the Valenciennes coal basin embraced twenty-four concessions, three were damaged by artillery bombardment, but have resumed operations since the' armistice, nine had their surface: equipment destroyed by battle, pillage, and sabotage, while twelve concessions at the eastern-end of-the field suffered from wilful, systematic destruction. Of the 285 shafts in the district, 172 were flooded either by: turning surface streams into them, or, by wrecking the cuvellage; thus, admitting water and quicksand from the water-bearing strata above the coal measures. Two hundred and thirty-five surface plants were damaged, many of them to such an extent that they must be scrapped. These properties gave employment to 135,000 men before the war and, even admitting the remote possibility of getting workmen, the terrible destruction and devastation makes housing and living a difficult problem. It will probably be from 3 to 5 years before the mines are drained and information obtained as to underground conditions; to attain the pre-war output may require from 12 to 15 years.

Jan 8, 1919

By A. U. Seybolt, R. A. Oriani

The pressure and composition of the solid solution of nitrogen in chromium has been investigated as a function of temperature. The partial molal heat of solution, the activity of nitrogen in solid solution, and the partial molal free energy have been computed. The enthalpy of three reactions is summarized: N + 2Cr(3) = Cr2N(4), H° = —28,500 cal per mol 1/2N2(p) + 2Cr(8) = Cr2N(3)1 ?HO = —23,500 cal per mol 1/2N2(p) = N, ?H° = 5,000 cal per mol. WORKERS who have investigated the problem of the preparation of ductile chromium have been concerned with the effects of minor amounts of impurities upon this refractory metal. In particular, gaseous impurities such as oxygen and nitrogen have been suspected of causing trouble because of many known cases where brittleness in transition elements has been definitely traced to these elements. In order to evaluate the possible effects of the nitrogen impurity in chromium, it appeared desirable to learn something of the dependence of the nitrogen solubility upon temperature and pressure. Previous Work Maier3 in 1942 in his treatise on sponge chromium reviewed the thermodynamics of the chromium nitrides Cr2N and CrN, both of which are well-estab- lished compounds, but which apparently have not been studied in much detail. Maier presented some free energy-temperature expressions for the reactions 2 Cr,N = 4 Cr + N2 [1] and 4 CrN = 2Cr2N + N2 PI based mainly on the work of Satoh2 and Sano." Pearson and Ende3 in 1953 briefly reviewed the thermodynamics of Cr-N using the same data available to Maier, and also derived a free energy-temperature expression for reaction 1. Of the two nitrides mentioned previously, the present investigation was only concerned with Cr,N, since this nitride is in equilibrium with the metal phase, at least over most of the temperature range, Blix4 in 1929 established the structure of Cr2N (close-packed-hexagonal) by X-ray diffraction methods, and indicated that its homogeneity limits extend from 11.2 pet to 15.1 wt pet N. At a temperature of 1200°C, 38 mm Hg from the Maier expression and 43 mm Hg from the Pearson

Jan 1, 1957

By Lawrence Burkhart, S. B. Joo

Axially unsymmetric ordered circulation patterns on the surface of a hemispherical constant volume drop with forced Internal motion were considered as a manifestation of hydrodynamic instability, which was affected by internal flow as well as by the properties of the interface A simplified mathematical model was analyzed In order to study the mechanism of onset of interfacial circulation from a non-circulatory basic state. Values of the critical Reynolds numbers were obtained when the basic state became a fully developed rotational flow and the values changed for different interfacial properties. The work describes a heretofore unreported surface flow pattern on drop surfaces From a practical point of new, any motion in the interface of a droplet can have a significant effect of mass transfer rates in solvent extraction processes Although surface motion in droplets actual processing equipment is very complex, continued study of the fundamental nature of such phenomena should ultimately lead to more effective equipment design procedures.

Jan 1, 1981

By Irving B. Cadoff, Stojan M. Zalar

AgInTe2, CuInTe2, and all Proportions of CuxAg1-xInTe, forMed homogeneous single phase alloys after direct solidification from the nielt. X-ray analysis indicated a zinc-blel~de strzccture typical of the chalcopyrite compounds, and the electrical resistivity and Sccbeck coefficient values were in the semiconducting range. AuInTe, and AuxA4g,-, InTe, formed by what appeared to be a peritectic reaction (the thermal analysis curves showing more than one arrest) and were conseyue~ztly polyphase. Substitution of copper into AgIrzTe, resulted in a continuous transition in the room tenzperature Seebeck coefficient from the negative AgIzTe, to the positive CuInTe,. A zero coefficient was obtained at about Cuo.55 Ago.45 InTe, . The temperatzire variation was similar to that observed for the stoichiometric compounds, that zs, tendency towards "p" concEuction at elevated temperatures. The thernzoelectric figure of merit for the compo~uzds, as determined by the Putley -Harmnn method were in the range 10- to 10-7 "K-l; the thermal conductivities in the order of 0.15 cal per sec-cm-oK. INCREASED interest in semiconducting intermetallic substances is expanding much of recent research from simple binary compounds into polyatomic systems and solid solutions. Ternary compounds A' represent a covalent extension of the binary semiconductors Within the a tin isoelec-tronic series, Ag-Cd-In-Sn-Sb-Te-I, divalent cadmium atoms in CdTe are being substituted for by monovalent silver and trivalent indium atoms to form the compound AgInTe, . By cross-substitution with elements of other isoelectronic series, a great number of ternary compounds A 'B"'c? is possible. In all of them, however, a necessary though not sufficient condition for the covalent, semiconducting bond—that there be four sharing orbital electrons per atom—must be fulfilled. In AgInTe,, each silver or indium atom is tetrahedrally surrounded by four tellurium atoms, while each tellurium atom is co-valently bound to two silver and two indium atoms. Synthetic chalcopyrites A'B"'c~ were first recognized as potential semiconduct&rs by Goodman and Douglas.' Austin, Goodman, and Pengelly discuss preparation difficulties and some electronic measurements on AgInS, , AgInSe, CuInSe, , AgInTe, , and CuInTe,. Chalcopyrites A B c2v are mentioned in papers attempting to classify and predict semiconducting behavior of intermetallic compounds; on the basis of saturated tetrahedral sp3 bonds,3 by specific selection criteria,' and by crystallographic considerations."

Jan 1, 1962

By John Birkinbine

(Read at the Philadelphia Meeting, February, 1878.) IN a former paper* attention was directed to the various firms of pumping machines employed for permanent work in mining and metallurgical processes. The following is simply a collection of memoranda of work done of a temporary character, and is presented by way of comparison with other work of similar nature. In close proximity to the charcoal furnace at Pine Grove, Cumberland County, Pa., is a large deposit of superior hematite iron ore, which has been worked for a number of years, and from which many thousand tons of ore have been taken by open pit workings. In July, 1874, the furnace was blown out and operations at the bank suspended, the machinery for draining being removed except a plunger pump, 18 inches in diameter and 66 inches stroke, operated by a steam-engine by means of rods. The pit was allowed to fill with water, and no steps towards its reclamation were taken until November, 1877. At that time the pit was a pond of water at the base of the mountain, having an area of about four acres and a depth of seventy feet. As the pumps, rods, etc., had been submerged for over three years, and partially buried by the mud washed down from the banks, and as it was determined to change the location of the pump for future operations and drive it by water-power, a temporary pumping apparatus was determined upon for reclaiming the pit and keeping it drained until the permanent arrangements could be completed. By opening an old adit about 10 feet of the water was removed, and the area decreased to three acres. The inflow of springs was found to be 250 gallons per minute, and the amount of water contained in the pit was computed to be 45,000,000 gallons. As the inflow would undoubtedly increase while the water sank in the pit, provision was made for removing at least 60,000,000 gallons, at the rate of 1,500,000 to 2,000,000 gallons per day. The company determined to employ a Heald and Cisco centrifugal pump driven by an oscillating engine by means of a belt. Steam was supplied by four plain cylinder boilers, each 36 inches diameter *Transactioiis of the American Institute of Mining Engineers, vol. p. 455.

Jan 1, 1878

By Frank Alfred Fahrenwald

MetallURgical research has discovered many an alloy possessing properties not combined in any single metal, and progress still consists chiefly in the investigation and utilization of alloys. In the case of iron, the demands of automobiles, high-speed machines and high-duty engines have led to the production of special iron alloys which will meet any reasonable specifications in that field. In like manner, the bronzes, brasses and other alloys of copper have been brought to remarkable perfection, and for nearly every industrial purpose some alloy has been , found more suitable than the pure metal. Less complete success has attended the attempt to find substitutes for gold, platinum, and the other precious metals. Indeed, it is not likeiy that a material can be produced which, will possess all the properties of any one of them; yet it is reasonable to hope that, for any given use, the properties required may be found in some less expensive material. Thus, in incandescent electric lamps, the wire passing through the thick glass neck of the bulb was, until recently, almost universally made of platinum, for the single reason that no other known material, suitable as a conductor, had the same coefficient of expansion as glass. But a comparatively recent investigation of the iron-nickel series1 has shown that alloys of those metals maybe produced, the coefficient of expansion of which can be accurately controlled between that of iron or nickel and zero. Thus, in that particular industry, a substitute for platinum has been found. According to statistical reports, not only considerable quantities of gold and iridium, but also more than one-third of the annual supply of platinum, are used (and, in the nature of the case, irrevocably lost) by dentists. Platinum is thus employed in several forms. As a thin foil, it serves various purposes for which its high melting point, pliability, chemical resistance, and other properties—including the ease with which it may be soldered—are invaluable. But it is most extensively used in

Jan 1, 1916

By J. E. Johnson

(Cleveland Meeting, October, 11,1912.) THE subject of blast-furnace slag is one which has had much consideration, particularly from the scientific standpoint, and several years ago technical literature contained many learned discussions on the oxygen-ratio of the acids and the bases, all on the assumption that acids and bases must be present in a ratio depending on molecular weight and chemical valency. Much work has also been done, sometimes in conjunction with the former, on the total heat and the temperature of initial fusion or softening of various slags. A wider knowledge of the blast-furnace now enables us to say that for practical purposes this work has been of almost no value. It is now generally admitted that on the physical side the important point of a given slag is neither its total heat of fusion nor its softening-point, but its free-running temperature, since this is the critical temperature of the furnace. This temperature bears no definite relation to the softening-temperature, as determined by Seger cones, for instance, because some slags melt relatively like ice, with a very short viscous-range, while others melt relatively like tar, with a very long viscous-range. In one the difference between the softening- and the free-running temperature may be very small, as little as 100° F., while in another this difference may easily be 200° or 300°. The importance of this difference is so great in practice as to destroy completely the value of exhaustive investigations, even such as those of 0. Boudouard, published a few years ago.1 * Presented also at the Joint Meeting of the Institute with Section IIIa, Metallurgy and Mining, of the Eighth International Congress of Applied Chemistry, New York, September, 1912. 1 It may not be amiss at this point to call attention to the excellent suggestion of Woolsey McA. Johnson, made several years ago, for determining the temperature at which different slags have the same practical fusibility. This suggestion

Oct 1, 1912

By Robert H. Merrill

In 1960, the Kennecott Copper Corp. and the U.S. Bureau of Mines entered into a joint research program to determine the changes in stress, strain, and displacement created by changes in slope angles. The field site was the Kimbley Pit, located near Ely, Nev. The supporting laboratory investigations were made at the Bureau's Denver Mining Research Center. Following a study to determine the rock stresses in the mining district, the strike and dip of geologic defects (fractures) in the rock, and the laboratory-determined strength of the rock, a new slope angle and pit configuration was selected, and instruments were installed to measure changes in stress, strain, displacement, microseismic noise rate, and sonic velocities at several points in the west wall of the pit. Between February and November 1966, the west slope was changed from an average angle of 45' to a slope angle that started at 45° on the south wall, and gradually increased to 575' at the center of the west wall, and to 61° on the north wall. The pit was deepened from about 500 ft to about 550 ft. About 2.55 million tons of waste and ore were removed by stripping and mining. Measurements made between November 1965 and September 1967 showed that the pit wall was stable before excavation began, that changes in the measured quantities occurred in the pit wall during the excavation, and that the wall returned to a condition of equilibrium after the mining was completed. The need for a method and the technology to pre-design a pit slope does not require elaboration. About 5 billion tons of material are excavated yearly by surface mining methods in the United States, and the economics, safety, and availability of lower grade metals, nonmetals and fuels could all be substantially improved if operators could preselect optimum slope angles. Mining companies and the Bureau of Mines have recognized the need for developing engineering methods to determine stable slope angles. In the industry, Kennecott Copper Corp. had been making an

Jan 1, 1969

By I. C. White, G. H. Ashley, J. A. Bownocker

Among the rich mineral deposits of the great Appalachian field, the Pittsburgh coal bed stands pre-eminent. Other coal beds may cover a wider area, or extend with greater persistence, but none surpasses the Pittsburgh seam in economic importance and value. It was well named by Rogers, and his able assistants of the First Geological Survey of Pennsylvania, in honor of the city to whose industrial growth and supremacy it has contributed so much. Whether or not the prophetic eye of that able geologist ever comprehended fully the part which this coal bed was to play in the future history of the city that gave it a name we do not know; but certain it is that the 7 ft. of fossil fuel, which, in Rogers' time, circled in a long black band around the hills and, overlooking the site of Pittsburgh from an elevation of 400 ft. above the water of the Allegheny and Monongahela, extended up the latter stream in an unbroken sheet for a distance of 200 miles, has been the most potent factor in that wonderful modern growth that has made the Pittsburgh district the manufacturing center of America, and that bids fair to continue until it shall surpass every other district in the world, even if it does not now hold such primacy.' The Pittsburgh coal bed stands today as probably the largest contributor of wealth of any single mineral deposit in the world. If it is not, what other deposit is? It has contributed to Pennsylvania alone more than 2,500,000,000 tons of high-grade coal worth nearly $4,000,000,000; since 1910, it has added more than $2,500,000,000 to the value of Pennsylvania's mineral output. In 1920, this bed2 contributed 127,227,000 tons of coal as follows: Pennsylvania, Pittsburgh district........................ 38,245,000 Connellsville district................................. 34,095,000 Weatmoreland-Ligonier district........................ 16,107,000 88,447,000 West Virginia, Fairmont district........................ 15,571,000 West Virginia-Ohio, Panhandle No. 8 district............. 21,128,000 Maryland-Potomac (Est. one-third of production)......... 2,081,000 38,780,000 Total........................................... 127,227,000

Jan 1, 1927

By J. E. Spurr

Jan 1, 1903

By J. A. B. Forster

The operations of the Electrolytic Zinc Co. of Australasia Ltd. involve the preliminary roasting of zinc concentrate from Broken Hill, New South wales, at a number of acid-making centers on the Australian mainland. The partially roasted material is shipped to the Tasmanian plant where it was formerly re-roasted prior to leaching,' but this practice was gradually abandoned in favor of the flotation of leach residue for the recovery of a concentrate containing about 22 pct sulphide sulphur and known as secontlary or Risdon concentrate.2 This change, together with increased zinc production, called for new furnaces at Risdon for the roasting of 10-50 tonst of secondary concentrcite and 90 tons of new concentrate per day. The war situation made it imperative that construction be commenced without delay and to save time it was decided to base the design on that of Skinner type furnaces which had been built in South Australia twenty years earlier. This involved some sacrifice of desirable features but did not prevent the incorporation of provisions which had enabled small Herreshoff type furnaces to roast secondary concentrate autogenously. The roasting rate in existing furnaces was 10-12 Ib sulphide sulphur per sq ft of hearth area per day, and eleven hearths, 20 ft in diam, were provided in the two new furnaces in anticipation that they would prove capable of the autogenous roasting of 130-140 tons of concentrate per day from 28-29 pct sulphur down to 4.5-5 pct, with an oxidation rate of 11-11.5 lh S/S per sq ft of hearth area per day. It was soon realized, when the first of the furnaces went into operation, that a much better performance than this might be given, and the purpose of this paper is to show how a treatment rate of 100 tons per furnace day, and oxidation rates approaching 15 lb S/S per sq ft per day have been reached. Furnace Design General specifications for the design were based on the results of experience with several other types of furnace and on the special operating conditions

Jan 1, 1950

By Samuel Wyer

1. THE following is an abridgment of a recent report made by the author, covering an investigation of (A) The necessary use of natural-gas compressors; (B) The effect of gas compressors on natural-gas field operating conditions in Ohio, with special reference to the working pressure relations of gas wells of one company discharging by natural rock pressure flow without compressors, and adjacent wells of other companies, discharging into intake lines to gas-compressing stations. Tests were made at 107 different places in the counties of Fairfield, Licking and Knox, Ohio, which required 7,000 miles of automobile driving, and consumed 6 months' time. 2. A proper conception of. the necessary use and effect of natural-gas compressors in natural-gas production necessitates a clear understanding of certain fundamental definitions and judicial doctrines, which are given herein. 3. Gas is a fluid composed of a large number of molecules which are vehicles of energy continually in motion, and having an inherent. tendency to get farther and farther apart. The range of motion of the molecules is limited only by the volume of the closed containing vessel in which they constantly move to and fro. The most distinguishing characteristic of gas is its universal property of completely filling an inclosed space.

Jan 2, 1916

By G. S. Scott, H. G. Turner, W. L. Kleene

It is well known that different forms of carbon show differences in chemical behavior under apparently identical conditions. It is fairly well known that these differences persist, although to a lesser degree, in a single group of carbons, such as the anthracites of Pennsylvania. It is the purpose of this paper to show the extent of these variations for Pennsylvania anthracites from actual quantitative measurements of the amount of carbon dioxide reduced under the standardized test conditions employed. As the amount of carbon dioxide reduced to the monoxide (under comparative conditions termed, for convenience, the "reactivity") is important in combustion, gas production and metallurgy, it is hoped that this paper will be a useful contribution to the store of knowledge on these subjects. In carrying out the investigation, considerable time and thought were spent in obtaining what seemed to be the best possible design of apparatus. The next step consisted in making a number of trial runs on the same sample, varying temperature, particle diameter, etc. and then outlining a standardized procedure to be followed in testing all samples. Fifty anthracites were tested. As a matter of interest, some 10 miscellaneous samples were also tested. The data show initial reaction temperatures (abbreviated I.R.T.), reaction velocity constants at 900" and 950" C., some effects of added substances, and a few additional tests designed to throw some light on the causes of differences in reactivity. The sample of charcoal, as was anticipated, proved to be easily the most reactive of any sample tested. The anthracites as a group came second. The five samples of gas and by-product cokes, obtained from five different coke manufacturers, came third, and a single sample of Rhode Island anthracite ranked fourth, with respect to reactivity as above defined. Although the five coke samples do not necessarily represent the average market coke, and five samples constitute a rather small number of samples to serve as a basis for comparisons, the fact that none

Jan 1, 1934

By F. L. Fayers, J. W. Sheldon

It has been a matter of concern to the petroleum industry to determine what effect the capillary term has on saturation profiles, since these profiles determine ultimate economic oil recovery. In their original solution of the non-capillary two-phase flow problem, Buckley and Leverett&apos; showed that solutions of the two-phase flow equations became multiple-valued in saturation. Since it is physically unrealistic for saturation to have more than one value at a given position, Buckley and Leverett resolved this difficulty by introducing a saturation discontinuity or "shock". They evaluated the strength and position of the shock from material balance considerations. Recently Sheldon, Zondek and Cardwell&apos; have demonstrated that the method of characteristics can be used to solve this and related problems. Owing to capillarity it is physically unlikely that saturation shocks occur in an oil reservoir. Buckley and Leverett suggested that the effects of interfacial tensions should be included in the fluid flow equations, if the solutions are to give continuous single-valued saturation distributions. An analogy to this problem is encountered in the theory of wpersonic compressible flow where the introduction of the viscous term eliminates shock behavior. However, the mathematical form of the capillary term in the porous medium fluid flow equations differs from the viscosity term in the Navier-Stokes equation. This paper demons~rates that capillarity does eliminate the triple-valued behavior and indicates the magnitude of capillary and gravity effects on the saturation profile for a variety of systems. DERIVATION OF LAGRANGIAN AND EULERIAN FORMS OF THE DISPLACEMENT EQUATION The equations representing capillary, two-phase flow are given by applying Darcy&apos;s law and a material balance condition for each phase. The familiar Darcy and material balance equations are as follows. ^U*^0......<3, ^^r=°......c« S is the saturation of the water phase, and B the inclination of the porous medium. Pressures in the oil and water phases differ by the capillary pressure associated with the interfacial tensions, P.-P.=pAS)..........(5) where p, is determined experimentally. The porous medium is said to be oil-wet if P, > Po and water-wet if P, < Po. If the fluids are incompressible and the total volumetric flow rate, q, is constant, then v, f v,, = q...........(6) By eliminating P.. /»,, and v, from Eqs. 1, 2, 5 and 6 it follows that It is convenient to normalize the variables in the problem after the manner of Handy and Hadley% so that Eqs. 3 and 7 become where j,, = —, the fractional flow of water; (F, is a capillary pressure normalizing constant.) Substitution of Eq. 9 into Eq. 8 gives In this partial differential equation for an initial value

By F. R. Brotzen, J. Taranto

SEVERAL investigators have computed stacking-fault concentrations from X-ray diffraction data.&apos;-&apos; The method generally employed relates the line shift to the stacking-fault probability. In this investigation platinum filings of 99.99 pct purity screened to -325 mesh were studied after having been subjected to various annealing treatments. The lines were measured on a General Electric XRD-5 spectrogoniometer using CuK, radiation. The centroid of the broad reflections was determined by the method proposed by pike.&apos; The stacking-fault probability was calculated by the formula given by Warren and warekois,3 with the assumption that all stacking faults were on the (111). Various high-angle reflections were used, but most data collected refer to the shift in the (400) reflections. When the filed platinum powder was annealed at 1200°C for 20 min the stacking fault concentration was too small to be detected. The stacking-fault probability in freshly filed specimens, as determined by the line shift relative to the annealed specimen, was about 0.016, Fig. 1. If the faults would be created only by extended dislocations, the dislocation density in the filed specimen would be about 3X1012 cm-2. The average stacking-fault width of about 21 which was used in this computation, is that given by Thornton and Hirsch.7 The mechanism by which stacking faults are annihilated during annealing is not yet fully understood. The isothermal results obtained do not seem to support the simple hypothesis of a first-order decay. On the other hand, the analysis by Kuhlmann, Masing, and Raffelsieper8 for the loss of dislocations during recovery agrees much better with the experimental data of this investigation. This analysis yields an activation energy of 29 ± 8 kcal per mol for the disappearance of stacking faults in cold-worked platinum during annealing. Even if one takes into account the lack of accuracy inherent in this X-ray method, the activation energy found is substantially less than that of self-diffusion in platinum, i.e., 61.6 kcal per mol.9 The results therefore suggest that processes other than dislocation climb, which involves the activation energy of self-diffusion, are responsible for the loss of stacking faults in platinum during annealing. The broad reflection lines became sharper early in the recovery process, Fig. 1. The sharpening occurred well before the stage during which stacking faults disappear. This lends support to Nowick&apos;s10

Jan 1, 1962

By A. Yoshikawa, T. Sugeno

To detenmine the origin of the sharp fatigue limit in many ferrous metals, S-N curvces were determined in push-pull fatigue at 18.6 kc per sec at room temperature and - 67°C for various kinds of iron. These differed in carbon and nitrogen content and grain size (25 and 2500 grains per sq mm). Sharp knees appeared in the S-N curves of fine-grained specimens with high interstitial content at both temperatures. In coarse-gruined specimens, knees were not sharp .regardless of the interstitial content and the testing temperature. It is concluded from these results that the controlling factov for the appeavance of the sharp fatigue limit is not strain aging but grain size. It has already been mentioned that iron and some iron alloys show fatigue curves characterized by a more or less sharp knee and a fatigue limit.&apos; Explanations of the origin of this characteristic behavior of fatigue in iron appear to fall into two broad classes. One is concerned with interstitial impurities through the aging or locking effect and the other is based on intrinsic plastic properties of iron. Levy and sinclair2 and Lipsit and Horne3 have suggested that the fatigue limit observed generally in iron and steel is due to interstitial solute aging during the course of fatigue. On the other hand, Thompson and wadsworthl have suggested that the fatigue limit may be analogous to the sharp yield point, in the sense that alternating stresses above the fatigue limit are necessary to break down the dislocation locking. However, there are some experimental results which cast doubt on the general validity of these suppositions.4-8 Ferro and Montalenti&apos; have recently suggested that the typical form of the fatigue curve of iron seems to come from an intrinsic plastic characteristic of the iron structure. This suggestion is based on the experimental result that pure iron containing an insufficient amount of interstitial solute to alldw appreciable strain-aging effects still showed a fatigue limit at room temperature. Although systematic investigations on the effect of grain size are scarce, it is thought that this effect is important in relation to the sharp fatigue limit. In fact, sensible differences were observed by Oates and Wilson4 in fatigue behaviors of a low-carbon steel depending on grain size. Ideally, the fatigue limit will be defined as the upper limit of stress amplitudes at which the life is infinite. This ideal fatigue limit can never be determined because of the limited time available for experiments, and moreover scattered data points often leave the construction of S-N curves somewhat arbitrary. And, it is usually stated that a material has a fatigue limit when its statistical S-N curve becomes apparently parallel to the N axis with a more or less sharp knee. The meaning of the fatigue limit and the sharp knee will be discussed in detail in relation to the construction of S-N curves. The origin of this sharp knee was investigated by determining S-N curves of iron for various interstitial contents, testing temperatures, and grain sizes. EXPERTMENTAL PROCEDURE The material as received was a commercial-grade low-carbon steel in the form of 4-mm-diameter rods with the following composition in weight percent: C, 0.09; Si, 0.017; Mn, 0.43; P, 0.006; S, 0.012; Cu, 0.11. Five different groups of specimens were tested. The grain sizes and interstitial contents in each group are given in Table I. The specimens of group C-02 were decarburized by annealing for 100 hr at 700°C, followed by an additional 100 hr at 850°C in wet hydrogen. Specimens of groups N-2 and N-9 nitrided in a mixed atmosphere of ammonia and hydrogen after an initial treatment identical to group C-02. The specimens of group C-9 were prepared in a manner similar to those of group C-02, except heat treatment was carried out in a vacuum. After polishing their surface with emery paper, the specimens of all groups were given a final anneal for 30 min at 930°C and air-cooled in an evacuated quartz tube. For group C*-9 this

Jan 1, 1965