Search Documents

By H. S. Rankin, E. C. Houston

OLIVINE is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 per cent; Mn, 0.012 per cent; Ni, none. Chlorination[f] of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SUPPLY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.1 The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940. It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. PREVIOUS TECHNICAL WORK In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. Unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment5 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By Friedrich Wellmer

INTRODUCTION The Ramsbeck Pb/Zn Mine is located in the northern Sauerland area of West Germany, 150 km N of Frankfurt and 120 km E of Cologne. This is a vein deposit which has been worked from the middle of the 19th century to 1974. About 15 million tons of ore were mined and milled. The ore district contains several vein deposits and is roughly 14 km in length and 4 to 5 km in width. The host rocks are strata of Lower Middle Devonian age. The strata strike 60° to 70° NE and where overturned have a dip steeper than the veins (Fig. 1). The galena-sphalerite mineralization is in quartz veins, which are mineralized where they cut the "Main Ramsbeck Quartzite" horizon, a very competent host rock. Vein structures strike at 65º to 75º, dip about 20° to 25º SE and cut the quartzite at approximately 60 m intervals. The main or "steep veins" within each vein structure dip at 10º to 80° SE with an average of 30° and are offset by thrust faults dipping 5º N to 40° S with an average of 5º S. "Flat veins" usually weakly mineralized occur in the thrust faults between the "steep veins", thus forming the overall step-like vein structure. The mineralization is very irregular and changes a- long strike and down dip. It consists of thin veins of pure sphalerite and galena with quartz and pyrite. The thicknesses of the pure sphalerite and galena veins

Jan 1, 1977

By W. O. Philbrook, H. W. Hosking, N. B. Melcher

Rates and patterns of gas flow in an experimental blast furnace were investigated by measurements, at three levels, of gas compo-sitions and temperatures and by direct determination of gas transit time by a new method employing mercury vapor as a tracer. Infer-ences were drawn about localized reaction zones and the mechanism of the onset of' channeling. LACK of precise knowledge of the nature of gas movement in the blast furnace has always been an impediment to better understanding of the blastfurnace process as a whole. The effects upon operation of various types of charge distribution are very largely brought about by the modifications to gas flow which they occasion. Intelligent evaluation of these effects demands a better understanding of the factors influencing gas flow and the ways in which the flow pattern is altered by conditions existing in the stock column. The same knowledge is required before a fundamental approach can be made to the problem of establishing optimum lines for new furnaces. An experimental furnace is operated at the Bureau of Mines Central Experiment Station, Pittsburgh, Pa. Advantage was taken of experimental operation to conduct an investigation to develop and evaluate methods of study which could be applied later to industrial furnaces. The gas composition and temperature determinations were made as a preliminary study so far as gas flow was concerned but yielded significant information relating to other processes occurring within the furnace. The direct measurement of gas transit times by the mercury-vapor method constituted the major object of the investigation. Development of the mercury-vapor method was carried out while the data on gas composition and temperature were being collected. A complete description of the principle and development of the mercury-vapor method is beyond the scope of this paper but is available elsewhere. The results obtained and some consideration of the method's effectiveness and its potential value in the study of industrial problems will be treated here. DESCRIPTION OF FURNACE The general lines of the experimental blast furnace are shown in Fig. 1. The hearth diameter was 3 ft at the beginning of the investigation, and this was later enlarged to 3 ft 9 in. and finally to 4 ft to increase capacity. Tuyere to stockline height is 21 ft 4 in. The bosh depth is 3 ft 4 in. over which it opens to a width of 5 ft, and this diameter is carried up for 2 ft in a cylindrical section. The inwall batter of 1/2 in. per ft. is considerably less than in larger installations This may have influenced the movement of gaseous and solid materials. The furnace is inside a laboratory building and is charged from outside by a skip and hoist. Feeding into the first of three bell chambers, the stock is distributed by rotating the upper bell, the other two being used to obtain an effective gas seal. Three water-cooled tuyeres, with a nozzle dia-

Jan 1, 1960

By R. C. Allen

ABOUT four years ago the writer proposed a revision of the correlation of the Huronian formations in Michigan, and noted the bearing of the question on the correlations of the Huronian rocks in Wisconsin and Minnesota.1 Dr. C. K. Leith opposed this revision and argued for the retention of the correlations of the United States Geological Survey, published in 1911,2 for which he and Dr. Van Hise were mainly responsible. As late as June, 1917, Harder and Johnson, following Leith, thought it "premature to change radically a correlation based on years of careful field work."3 The work of Wolff on the Mesabi and Cuyuna Ranges, of Hotchkiss on the Gogebic Range (unpublished), and of the writer and assistants on the Michigan ranges, together with data developed by exploratory and mining operations, has introduced so many pew facts not recognized in the scheme of the U. S. Geological Survey that the correlations of 1911 must be considered, in some important respects, obsolete. Indeed new data are accumulating so rapidly that any classification, which for the moment may seem best to explain the facts, is almost immediately modified or refined by further observations. The problem of Huronian correlations is difficult, but interesting and important. With the aid of fossils, stratigraphers of the post-Algonkian formations have been able to show that slight disconformities may separate strata of vastly different ages, and that within physically conformable strata may be concealed a hiatus of great magnitude. In the non-fossiliferous Huronian group, minor physical breaks in the strata are

Jan 9, 1919

By Edward Martinez

Although the copper segregation process has been known as a method for treating oxide copper ores since the 1920's, the reactions involved in this process are still a matter of conjecture. However, the evidence turned up in a recent series of experiments at Asarco's Central Research Laboratories strongly indicates that some of the proposed reactions may not be occurring. Experimental work on oxide copper ores from the Sagasca mines in Chile led to the discovery of the copper segregation process in 1923. It was found that the reduction of the copper with coal at about 700°C occurred on the surface of the coal instead of remaining disseminated in the ore. The unusual behavior of the copper, which caused it to migrate from the ore particles to the coal, was traced to the presence of a small quantity of sodium chloride occurring in the ore. Further experiments with oxide copper ores proved that the presence of a halide, either occurring naturally or admixed with the ore, caused the copper to migrate from the ore particles and to segregate in the charge.

Jan 8, 1966

By Stanford O. Grodd

The Sanford Lake district encompasses an area covering 24 square miles in the central Adirondack Mountains of northern New York State. Discovery of the titaniferous magnetite deposits dates back to 1826. Several attempts to exploit the ores for iron prior to 1942 proved uneconomical because of difficulties with the associated titanium, lack of transportation facilities, and the isolated location. Since 1942, the National Lead Company has produced ilmenite concentrates for the titanium pigment industry, and a magnetite by-product used in the steel and refractory industries. Rocks of the area are Precambrian in age and of igneous origin. The area has a history of erosion, deformation, and metamorphism, subsidence, and finally uplift and glaciation. The resulting topography is extremely rough with drainage patterns controlled by a combination of fault patterns and glacial modifications. The district is within the large anorthosite massif making up the central high peak area of the Adirondacks. All of the various lowsilica rock types associated with the massif are found within the boundaries of the district. These consist of both the Marcy and Whiteface types of anorthosite and of gabbroic anorthosite, gabbro, and different grades of titaniferous magnetite ores. All of the rocks contain the same minerals and differ only in their percentages of these consitituents. Gabbro, and ore associated with it, demonstrate flow structure as both have foliation and lineation. Anorthosite and its associated ores are massive and show very little primary structure. Minor pegmatites and diabase dikes provide evidence of remobilization in selected areas and of late intrusion as well. Faulting is prevalent and follows a regional pattern of major faults trending northeastsouthwest and of minor faults at nearly right angles to them. There are four mineralized areas where an economic grade of ore has been found. Three of these have both gabbroic-type ore and anorthositic-type ore. The fourth has only gabbroic ore. Ores are graded according to their TiO, content, and these range from 9.5 per cent to over 30.0 per cent TiO,. Ore bodies of both types are related to gabbro and conform to the configuration of the gabbro bodies within the anorthosite. At least three distinct theories of ore genesis have been expounded by different investigators. Others propose some variations of one or more of these. Although complete agreement probably never will be reached, it is certain that no one process of ore emplacement can explain the complicated picture as seen today. Further understanding of the ores and their origin will require detailed mapping, sampling, and mineralogical studies of the entire district, and then it may never be understood without qualification.

Jan 1, 1968

By David A. Summers, Clark R. Barker, Marian Mazurkiewicz

In May 1975 the U.S. Bureau of Mines contracted with the University of Missouri-Rolla, Rock Mechanics and Explosives Research Center to develop a Hydrominer modification to a longwall shearer unit, wherein the rotating pick-laced drums and connecting gear drives are replaced by a water jet cutting ahead. The concept of the water jet cutting head is based on using the high localized energy of the water jets to isolate a slice of coal by cutting a slot under, at the back of, and at the top of the web. The plow blade of the head then advances into the cut and wedges the coal cantilever over onto the conveyor [(Fig. 1)]. There were several potential advantages foreseen for the system; perhaps the most significant were the elimination of coal dust from the working area and the ability, with a variation in nozzle geometry, to cut webs of greater depth with a small increase in haulage horsepower. The University initially designed the head, based on experiments carried out in the laboratory, under an earlier Bureau of Mines contract. The experiments showed that it was more advantageous to work at a pressure of 68.9 mPa (10,000 psi) with an estimated flow rate of 3.15 X 10 - 8 m3/s (50 gpm) than go to the higher pressures and lower flow rates which have been advocated elsewhere.

Jan 1, 1979

By H. K. Birnbaum, H. B. Aaron

he authors suggest that a number of the types of yield phenomena which have been observed in high-purity fcc metals are due to dislocation interactions bccurring at the surface of the crystals rather than due to volume effects. Since rather different inter-pretationS2,7,12,14,15,21-23 of these effects have been suggested, it is of some importance to ascertain the role of the surface in these yield phenomena. It should be first noted that the high-purity fcc metals appear to exhibit several distinct types of yield phenomena. The "unloading yield point" which is observed on reloading the specimen after removing the applied load has been found to be independent of the time of holding in the unloaded condition. If however the specimen is aged while under load and re-tested without removing the load, a yield point is observed which does depend on the aging time and tem-perature. Feng and Kramer suggest that the removal of the unloading yield point on removing sufficient material from the surface of the specimen indicates that the effect is associated with dislocation interactions at the specimen surface. Their observations are counter to those of Haasen and Kelly5 and Birnbaum.12 Since the unloading yield points are extremely small (-2 pct of the flow stress) the results of the surface removal will depend on whether the material is removed uniformly over the gage length. The introduction of small etch pits or the removal of more material from one portion of the specimen than from another will result in preferential yielding and obliteration of the yield point. With the normal electropolishing techniques it would be difficult to avoid these effects. The data obtained by Aaron and Birnbaum, Fig. 10, on aluminum polycrystalline specimens indicate that, although the unloading yield point and the strain-aging yield point are not simply additive, a time- and temperature-dependent yield point is observed under conditions where no creep is observed. This does not agree with the results of Feng and Kramer but does agree with the results on copper15 and gold.7~23 The source of the discrepancy may be the procedure used by Feng and Kramer to correct their time-dependent yield points for the effect of creep. Since the strain-aging yield point is not independent of the pre-aging strain rate, Fig. 11, the effects of creep cannot

Jan 1, 1967

The 114th (New York) Meeting of the Institute will be held in the third week of February, 1917. The Committee on Papers and Publications has set Dec: 1, 1916; as the closing date for the receipt of manuscripts intended for this meeting. Manuscripts must be received by the Secretary on or before this date. If they are sent through members of the technical committee they must be sent to those committees enough in advance of the time to be forwarded and in the hands of the Secretary by the time specified. While Dec. 1, 1916, is the final closing date, it is a great advantage to get papers in as much before that time as possible as it enables them to be submitted in proof form to their authors. Papers received on or before Nov. 1, 1916, will, as far as possible, be published in the January Bulletin or earlier, thus giving good distribution among the members in advance of tile meeting. The Institute's records show that the discussion of papers is very rnuch better when they are distributed somewhat in advance of the meeting instead of in the Bulletin which goes out immediately preceding the meeting.

Jan 9, 1916

By S. R. du Toit, W. J. Oberholzer, M. I. Watson, D. G. Krige

The objectives, essential features and implications of the 'random' and 'deterministic' types of ore value surfaces are examined as well as the basic requirements for a satisfactory prediction model. The 'random' method used on the South African gold mines and based on observed auto-covariance patterns is briefly discussed as well as its justification in preference to the 'deterministic' approach. Various mathematical models for auto-covariance patterns are examined for the one-dimensional case. It is also shown that these patterns as estimated for ore values in certain mines agree closely for various sizes of ore unit. In two case studies the variations in gold, uranium and ore thickness covariance patterns are examined and compared with certain geological features established independently from sedimentological studies.

Jan 1, 1969

By Oscar Weiss

STILFONTEIN and surrounding areas gave nega-tive results in all prospecting attempts since about 1904 when Goerz and Co., a forerunner of Union Corporation Ltd., first drilled in the region and on the farm Stilfontein. Subsequent efforts by African and European Investments Co. and Anglo American Corp. from 1934-37 were completely unsuccessful. Holes drilled by these companies on the farms Riet-fontein, Hessie, and Palmietfontein were stopped in the Lower Witwatersrand system without finding payable reefs. The results of gravimeter, ground magnetometer, and aerial magnetometer surveys are presented in the area, in and around the new Stilfontein Gold Mine, in the Klerksdorp District of the Transvaal in the Union of South Africa. The gravimeter and ground magnetic surveys were completed in 1947—48. The gravity anomalies suggested a block of Upper Witwatersrand quartzites faulted-up between denser rocks of dolomite and Ventersdorp lava. Boreholes S.T. 1, 2, and 3 were drilled in 1948 and, after penetrating the dolomite and Ventersdorp lava, entered Upper Witwatersrand quartzites and intersected the Gold Estates Reef and Vaal Reef. Subsequent drilling delineated the suboutcrop of the Vaal Reef and determined the main structure of this horizon. The gold content of the Vaal Reef was highly payable and shaft sinking is now in progress. The Stilfontein Gold Mining Co. has been formed and, up to date, f5,000,000 capital has been raised for plant, shaft sinking, and development. The payable Vaal Reef horizon extends further south from Stilfontein, the reef occurring at increasing depths. It is possible that at least another mine may be established on these deeper horizons. The farm Stilfontein 39 is situated in the Klerksdorp District of the Transvaal. This farm and the surrounding areas have been subjected to repeated programs of prospecting dating back to about 1904, when Goerz and Co., the forerunner of Union Corporation, Ltd., first drilled on the farm and in the surrounding areas. From 1934-37, numerous boreholes were drilled on the neighboring farms, Riet-fontein. Hessie. and Palmietfontein, by African and European Investment Co. and Anglo American Corp. All these efforts were completely unsuccessful, and nobody suspected any possible gold-bearing area on Stilfontein until about 1947, when a gravity traverse run by B. D. Maree on the main road, showed a negative gravity anomaly. During 1947-48, the writer's organization completed gravimeter and magnetic surveys on Stilfontein and Rieffontein. An area of negative gravity anomalies was mapped, and it was suggested that this could be caused by blocks of Upper Witwatersrand quartzites, of the average density of 2.65, faulted up between dolomites and Ventersdorp lavas, the density of both of these rocks being 2.8. Fig. 1 shows the geology of the area as mapped by L. T. Nel of the Geological Survey of South Africa. The boreholes on Stilfontein, with the exception of a single hole of Goerz and Co., were drilled after the completion of the geophysical survey. The grouping of the first boreholes S.T. 1, 2, 3, 4, 5, and 6, clearly shows that these were located in the zone of negative gravity anomalies. Fig. 2 shows the gravity anomaly contours. Fig. 3 shows two sections across the gravity anomaly, together with the corresponding geological sections as obtained from boreholes. The close relation between gravity values and thickness of dolomite plus Ventersdorp lavas is striking. The two latter formations having the same density (2.8), act as one mass as far as gravity effects are concerned. Fig. 4 shows the magnetic anomalies observed on the ground by vertical magnetometers and at 500 ft abbve mean ground level by aerial magnetometer. The latter are anomalies of the total magnetic intensity. The magnetic results show that, on the farm Rietfontein and on the northern half of Stilfontein. Lower Witwatersrand magnetic shales were to be expected at relatively shallow depths. As the strongly

Jan 1, 1952

By W. C. Hellyer, R. A. Campbell

In single-stage autogenous grinding, the buildup of a critical size fraction in the media can be corrected by removing this material through pebble ports, crushing it below the critical size range, and recycling the crusher product back to the mill. The rate at which the critical sire fraction is crushed affects the size distribution of the grinding media and this in turn affects the sire distribution of the grate discharge. This provides a means for controlling the grind produced by a single-stage autogenous grinding unit. The pilot-plant investigations on a very hard copper ore were carried out at the facilities of the Institute of Mineral Research, Michigan Technological University. In an autogenous grinding circuit in which feed at approximately 9 in. top size is reduced to a size suitable for subsequent processing, the build-up of a "critical size" fraction in the media causes problems. A "critical size" fraction has been defined as, "media too small to effect reduction by impact grinding of ore coarser than a quarter of an inch and too large to be broken by the largest size of media in the charge."' The buildup of a critical size fraction reduces the capacity of the mill, increases the grinding power requirements per ton of finished product, and generally produces a finer grind than is desired. It is general practice to overcome this problem by the addition of large-diameter steel balls to the grinding charge. This has certain disadvantages, such as 1) an increase in mill liner wear, 2) wear on the steel balls, and 3) some loss in flexibility in grinding circuit opera-tions resulting from difficulties in removing the steel balls by means other than by grinding out. A number of investigators' have suggested the use of a small crusher as an alternative to the use of large steel balls for control of a critical size fraction. With this technique the critical size fraction is removed from the mill continuously through suitable-sized pebble ports, crushed below the critical size range, and returned to the mill. An external crusher would cause no increase in mill liner wear, the wear on the crusher would be less expensive than the wear on the steel balls, and the flexibility of the grinding circuit operations would be enhanced since the crusher can be cut into and out of the circuit at will. This paper describes an autogenous grinding pilot plant investigation on a very hard copper ore, which led to the selection of an autogenous grinding flowsheet incorporating a crusher in the circuit as the preferred method for grinding this ore. Further development of the technique demonstrated that the crusher could be employed to control the product produced by an autogenous grinding unit. Description of Pilot Plant These investigations were carried out at the pilot-plant facilities of the Institute of Mineral Research, Michigan Technological University, Houghton, Mich. The autogenous grinding unit was a 6-ft-diam by 2-ft-long Hardinge Cascade mill with %-in. slotted steel grates. Pebble ports cut into the grates allowed passage of pebbles having a top size of approximately 21/2 in. The grate and pebble-port discharge material passed over a 3/16-in, trommel screen with the trommel under -size being pumped to the classification device. DSM screens were employed for classification in the early investigations, but were replaced later by a small Dorr rake classifier. The trommel oversize material returned to the mill via scissor conveyors. When the crusher was incorporated into the circuit, the trommel oversize material passed to a double-deck vibrating screen fitted with 2-in. and 3/4-in. square mesh screen cloths. The $ 2-in. and the —2 +3/4-in. size fractions were combined and crushed to a nominal 1 in. in a 4 x 6-in. jaw crusher. The crusher discharge and the —3/4-in. screen undersize returned to the mill. In the final investigation, a flap gate fitted to the top deck of the screen directed the — 21/2 +2-in. size fraction to the crusher or back to the grinding mill. The flap gate operated manually on a 15-min cycle, with this material being crushed for so many minutes out of each cycle. This was found to be a more reliable method of controlling the amount of — 21/2 +2-in. material crushed than attempting to make a split of a small weight of material on a continuous basis. Operational Techniques: Each sample was sized into three fractions and the Cascade mill feed was reconstituted from these size fractions in the proportions existing in the original sample. Sufficient feed for 15 min operation was weighed out and fed by hand over a 15-min period. The gross mill power draft was recorded every 15 min, corrected for tare power and drive efficiency, and reported as net kilowatt-hours per ton. A recording kilo-watt-hour meter provided a continuous visual record of the power drawn by the mill. Pulp densities of the trommel undersize and the classifier overflow (or DSM undersize) were taken every 15 min. The classifier overflow was sampled automatically. Timed samples of the classifier sands were taken every 15 or 30 min, weighed, and returned to the circuit. After correcting for moisture content, the weights were converted into percent circulating load. Timed samples of the +2 in., the —2 + 3/4-in., —3/4-in. screen fractions, and the crusher discharge, were

Jan 1, 1971

By Lewis E. Dr. Young

MINING engineers in the United States understand that mining conditions in the British coalfields are much more difficult than in most of the mines now being operated in the United States. We realize also that in the near future we must face some of these same difficult problems. Early Mechanization The progress made in mechanical loading in the United States is the result of a long struggle in many coalfields to mine with power tools safely and to increase output per man-shift. Attempts to use power to loosen coal and to transport broken coal in the U. S. may be said to date from the Stanly Header, or Entry-Driver brought from England in 1888. The principle of this boring machine was used in the McKinlay Entry-Driver, almost continuously used in the U. S. since 1920. Since 1888 experimental loaders, scrapers, and conveyors were installed with more or less success. Beginning in 1918, considerable progress was made with mobile loaders, and in 1920 the first wage agreement for the operation of mechanical loaders was made in Indiana. In 1923 the Pocahontas Fuel Co. loaded nearly 1 million tons of coal using 23 Coloders. Labor Policy The United Mine Workers of America have never officially opposed the Mechanization movement. On December 10, 1945, in a statement before the House of Representatives Labor Committee, John L. Lewis said, regarding the policy of the United Mine Workers of America: "We have welcomed progress; we have welcomed machines. We have told our people that they had to accept that condition; that it was the process of progress, and that they would have to take their chances." Recent Development In 1951 about 71 pct of the tonnage mined underground was mechanically loaded. Over 4000 shuttle cars are in service and it is estimated that much more than half of the tonnage loaded underground is produced by trackless mining. In 1947 roof-bolting was introduced extensively and it is estimated that more than 2 ½ million bolts are now being used per month in about 600 mines. The use of roof bolts has permitted the more effective and safer use of loaders and shuttle-cars. Continuous Mining The McKinlay Entry-Driver could have been used for continuous mining, but for many years it was used only .for entry driving. In 1946 the Silver machine was developed in Colorado, and in 1947 this was acquired by the Joy Mfg. Co. and called the Joy Continuous Miner. Other types of combination mining-loading machines which eliminate drilling and blasting operations are the Marietta Miner, the Colmol, the Lee-Norse Miner, the Junior Miner, the Goodman and the Konnerth machines. There are several other types in the process of development. Probably by January 1953 there will be about 250 continuous miners in operation in the U. S. Payment of Mine Labor One of the most important problems in mechanizing was the establishing of rates of pay that would be attractive to the best men. Prior to the installation of mobile loaders the hand loaders and cutters have been paid by the ton. It was felt that a system of a day's pay should be established and that piece and tonnage rates should be abolished completely. Without exception, all coal loaded in mines equipped with mobile loaders is prepared and loaded by men paid an hourly rate. Trends in Mining Research There are two diverse approaches in coal production research; to try to design a mining machine to fit current methods, or to adapt mining practice to take advantage of proven machines. A great deal of credit must go to the mine operators who have been enterprising and dynamic enough to use available equipment intensively and to discard it as soon as an improved or new machine is available. Effect of Changing Markets Formerly there was an important demand for lump and prepared coal in the larger sizes for domestic use. The use of bituminous coal for house heating has decreased so that not more than 19 pct of the annual tonnage goes to retail trade, only 12 pct is used by the railroads, and much of the retail and most of the railroad coal is in stoker size. As a result of this decline in the market for coarse coal most of the large mining operations have crushers installed in the tipples or preparation plants. Mass production at the face requires increased preparation facilities. Another important trend is in connection with complete seam mining with mechanical loading. In many mines where the immediate roof is apt to fall with the coal no effort is made to separate roof material from coal prior to

Jan 1, 1952

By Y. C. Kim, S. L. Barua

M. Armstrong's paper is very interesting and can be regarded as a pioneering work of applying geostatistics on washed coal. The density levels used in her study are uniformly spaced, which facilitated curve fitting through a proper experimental design. Most of the existing coal washing plants in the US, however, gather washability data at non-uniform intervals which, in turn, affects the goodness of curve fitting. We would like to emphasize the importance of having a proper experimental design, if a similar geostatistical application is to be conducted on washed coal. We, at the University of Arizona, tried the variogram on recovery (Kim, Barua, and Baafi, 1982, SME preprint 82-143) which showed a similar pattern as Fig. 4 of Armstrong's paper. In both cases, the first experimental variogram value is invariably and inexplicably higher than the second variogram value. Although Armstrong ignores the first point because of "small number of sample points," we did not do so because there were 17 sample pairs. As a consequence, we concluded that the obtained experimental variogram was unsatisfactory and that further research is warranted. In other words, this disagreement in variogram interpretation between M. Armstrong and the University of Arizona begs the question whether the experimental variogram of Fig. 4 truly reflects the spatial correlation in washed coal, assuming there is such a correlation. Finally, we wish that Armstrong could have done a similar study on clean sulfur, which is a vital interest to the coal mines in the US. Her implied remark on sulfur in the concluding section of the paper may turn out to be incorrect because our experimental variograms on clean sulfur at different density levels were even less satisfactory than those on recovery. ?

Jan 1, 1986

By C. H. Keplinger

WARTIME factors have strengthened the production engineering consciousness of the petroleum industry. The basic principles of sound oil-production technology have been accepted as the standard by the industry and the governmental co-ordinating agencies. Every effort is being made to furnish larger quantities of petroleum with a minimum expenditure of materials and under strict conservation practices. The sphere of influence of production engineering extends from fundamental reservoir control of withdrawal rates and reservoir pressures to bolstering production from stripper wells. Serious transportation difficulties in moving oil to the East Coast have stimulated secondary recovery operations in the Appalachian and East Central oil-producing states. Diminishing discovery of new oil reserves by exploration activities increases the importance of promoting efficient oil-producing methods and practices throughout all productive areas in the United Nations.

Jan 1, 1943

By J. J. Gilman

RECENT experiments have shown that the mar-tensite reaction in a standard tool steel is influenced by the history of the reacting austenite. The martensite reaction proceeds to a given extent at a higher temperature in austenite formed from an annealed spheroidal structure than it does in austenite formed from tempered martensite: that is to say, a prequench lowers the temperature range of the martensite reaction in this steel. Furthermore, a prequench alters the appearance of the martensite as compared to martensite formed from "virgin" austenite. The steel used for this work was a manganese nondeforming tool steel of the following composition: C, 0.85 pct; Mn, 1.43; Si, 0.23; Ni, 0.12; Cr, 0.59; and W, 0.59. A piece from a rolled bar was forged to Vz in. sq and annealed to a spheroidal structure. Disks 1/8 in. thick were used in the experiments. Several sets of the specimens were prepared and austenitized in lead at 1475°F. Three sets were held at 1475°F for 15 min, quenched in water, and immediately reheated to 1475°F. After this quench the three sets were held for 5 min, 30 min, and 3 hr, respectively, at 1475°F and then the individual specimens in each set were quenched in molten baths to 325", 300°, and 275ºF, respectively, and held for 15 sec. Immediately after the quenching treatments? the specimens were tempered at 600°F for 30 sec to darken the martensite and then were quenched in water. The holding times were short enough to avoid isothermal transformation. Three other sets of specimens were given the same final quenching treatments as the first three, but they were austenitized at 1475°F for 20 min, 35 min, and 3 hr and 15 min, respectively, without an intermediate water quench. The two individual specimens from each set were quenched together in order to eliminate quenching errors. Several experiments were run in this way but only the six sets referred to are described in detail because they all yielded essentially the same results. By means of the stated heat treatments the martensite reaction was investigated for: 1—austenite formed from an annealed structure, and 2— austenite formed from tempered martensite. The martensite reactions of the two types of austenite differed significantly. This is shown by Figs. 1 and 2. Comparison of the photographs on the left in Figs. 1 and 2 with those on the right shows that less martensite was formed by a quench to a given temperature from prequenched austenite than from austenite formed from an annealed structure, that is, the prequench suppressed the martensite reaction. The effect was observed for specimens austenitized 20 min, 35 min, and 3 hr and 15 min. A comparison of Figs. 1 and 2 shows that the martensite reactions in both sets of specimens occurred at lower temperatures with increased austenitization time. This was caused by the increased dissolution of residual carbides with time at 1475°F. However, the difference in amount of martensite formed in prequenched austenite as compared to virgin austenite was approximately the same for all three austenitization times. One further observation should be noted. The needles of the martensite formed from virgin austenite are somewhat longer on the average and show less of a tendency to cluster than those of martensite formed from prequenched austenite. This causes the martensite on the right in Figs. 1 and 2 to have a more acicular appearance than the martensite on the left. Since the sets of specimens used in this work were austenitized for identical total lengths of time and the effect of a prequench on the martensite reaction existed for specimens held at the austenitizing tem-

Jan 1, 1953

By F. B. Plummer

PERHAPS the greatest progress made in the technical methods of oil production during the last year has been in handling gas from the new fields that yield light distillate fractions. At least sixteen recycling plants have been perfected and installed in South Texas fields alone during 1939 having a daily capacity of more than one billion -2 cubic feet of gas and capable of producing more than a million gallons of distillate daily. The process consists of running the gas under pres- sure through especially designed plants, separating out the condensate, then compressing the gas to 3000 lb. or more, depending on the subsurface pressure in the formation, and injecting gas back into the reservoir to be produced again later, along with more of the liquid hydrocarbons, and again recycled. Hence production in these distillate fields in sense has changed from that of producing a constantly diminishing and much-wasted product to a more or less continuous manufacturing process, in which practically all the gas is conserved-a real triumph in engineering practice.

Jan 1, 1940

By W. A. Bruce

This paper covers the theory and present state of development of an apparatus for the nonmathematical analysis of complex problems of reservoir and well behavior. At the present stage of development of this apparatus, it is capable of solving the water-drive problem of any reservoir performance for which a mathematical solution has been presented in the literature, either on the basis of steady or unsteady-state flow analysis. The theory is presented for the extension of the scope of this analyzer along the lines of the present development. The resulting apparatus should be able to solve reservoir-performance problems previously thought too difficult for practical solution by mathematical means. As an illustration of its operation and present scope, the analysis of a reservoir problem and synthesis of expected performance is presented. Introduction In this method† of analyzing problems of petroleum-reservoir and well behavior, the porous continuum of the reservoir is assumed to be divided into small blocks, or units. Each block is assumed to be small enough so that for a material balance on the fluids in the block an average pressure for the block can be used. In analyzing reservoir behavior from this point of view by mathematical means, a set of simultaneous difference equations would be obtained (two for each block), which must be solved or combined into a partial differential equation. In the method to be described here, instead of solving these sets of equations analytically, electrical units are constructed, which will behave in respect to the flow of electricity exactly as the reservoir units behave under various conditions of fluid flow. The electrical units are then wired together in the same way that the reservoir units are connected naturally by virtue of their geometrical locations and shapes. Fluid-Flow Equations Consider a block in a reservoir. Assume that reservoir fluid (or fluids) is flowing in at one face and out at the opposite face, and that the block is small enough so that at all points the stream lines are within one degree of perpendicular to the face. Furthermore, assume that the pressure, pi, at the upstream face (Fig, I) is not more than one per cent greater than P2 the pressure at the downstream face. A material balance will show that the mass of fluid flowing out less the mass of fluid flowing in will equal the change in density times the fluid volume. This is expressed in the equation:

Jan 1, 1943

By W. A. Bruce

This paper covers the theory and present state of development of an apparatus for the nonmathematical analysis of complex problems of reservoir and well behavior. At the present stage of development of this apparatus, it is capable of solving the water-drive problem of any reservoir performance for which a mathematical solution has been presented in the literature, either on the basis of steady or unsteady-state flow analysis. The theory is presented for the extension of the scope of this analyzer along the lines of the present development. The resulting apparatus should be able to solve reservoir-performance problems previously thought too difficult for practical solution by mathematical means. As an illustration of its operation and present scope, the analysis of a reservoir problem and synthesis of expected performance is presented. Introduction In this method† of analyzing problems of petroleum-reservoir and well behavior, the porous continuum of the reservoir is assumed to be divided into small blocks, or units. Each block is assumed to be small enough so that for a material balance on the fluids in the block an average pressure for the block can be used. In analyzing reservoir behavior from this point of view by mathematical means, a set of simultaneous difference equations would be obtained (two for each block), which must be solved or combined into a partial differential equation. In the method to be described here, instead of solving these sets of equations analytically, electrical units are constructed, which will behave in respect to the flow of electricity exactly as the reservoir units behave under various conditions of fluid flow. The electrical units are then wired together in the same way that the reservoir units are connected naturally by virtue of their geometrical locations and shapes. Fluid-Flow Equations Consider a block in a reservoir. Assume that reservoir fluid (or fluids) is flowing in at one face and out at the opposite face, and that the block is small enough so that at all points the stream lines are within one degree of perpendicular to the face. Furthermore, assume that the pressure, pi, at the upstream face (Fig, I) is not more than one per cent greater than P2 the pressure at the downstream face. A material balance will show that the mass of fluid flowing out less the mass of fluid flowing in will equal the change in density times the fluid volume. This is expressed in the equation:

Jan 1, 1943

By WM. HUFF WAGNER

Computations and allowances for mine depletion for Federal income tax purposes depend upon the meaning of certain terms in the pertinent provisions of section 114(b) 4 of the Internal Revenue Code. Unfortunately, but one of these terms is defined in the Code. Congress left it to the Commissioner to define the other terms in the Regulations. Even though the Commissioner, through his staff, labored long and earnestly to draft these definitions they have not been satisfactory to the mining industry, because the definitions in the Regulations and the interpretation placed thereon by the Commissioner do not state what the industry believes to be the clear and obvious intent of Congress. Consequently serious and prolonged disputes, unduly delaying the settlement of Federal tax returns involving percentage depletion deductions are continually arising between taxpayers and the Commissioner.

Jan 1, 1949