Search Documents

By Carl E. Swartz

ALTHOUGH a number of articles appeared during the war advocating the use of cadmium in lead-tin solders, very little information of value can be found in the literature regarding the properties of solders containing cadmium. In most of the published articles the cadmium seems to have been considered merely as a partial substitute for tin in a tin-lead alloy rather than as an essential constituent of a ternary alloy. The primary object of the substitution of cadmium for tin was to lessen the amount of tin required, at a time when the latter was scarce and high-priced, and thus to produce a cheaper solder. While this object was accomplished, the new properties resulting from a change from a binary lead-tin alloy to a ternary lead-tin-cadmium alloy were not given proper consideration in many cases. For the past few years, the American Smelting & Refining Co. has been marketing a very considerable amount of cadmium in the form of lead-tin-cadmium alloys for use as solders for certain special purposes, and the successful use of these solders suggested that if more extensive knowledge were available concerning the properties of lead-tin-cadmium alloys of various compositions their field of usefulness might be materially extended. The investigation described in the present paper was undertaken to obtain this information and, by means of tests under conditions approaching those of practical use, to determine the suitability of cadmium solders for various purposes. CHARACTERISTICS AND REQUIREMENTS OF SOLDERS IN GENERAL General Physical Properties.-When cast into bars, solder should present a smooth and bright appearance free from oxide inclusions and bubbles. Ductility should be as great as possible without sacrificing tensile strength, and vice versa. Hardness and specific gravity are not of any great importance. Melting Characteristics.-The melting or solidification range is important. This statement applies both to the extent of the range and to the actual temperature at which complete solidification occurs. A rather narrow solidification range is desirable in soft solders in order that solidification may take place quickly. The solder should have high fluidity at temperatures only slightly above its melting range. For a

Jan 1, 1928

By Hsun Hu

Direct observations were made on the recrystalli-zntion of a cold-rolled (110) [001] crystal of 3 pct Si-Fe by annealing thin sections of the specimen inside the electron microscope during examination. Subgrain formation, presumably by polygonization, occurs rapidly, followed by a slow increase in the subgrain size before recrystallization can be detected. No migration of the subgrain boundaries was observed, and the formation of recrystallization nuclei by coalescence of subgrains is suggested. Re-c~ystallization characteristics of various texture components were individually examined. AS reported in a previous paper: orientations of the various deformation texture components in a 70 pct cold-rolled (110) [0011 crystal of 3 pct Si-Fe were completely confirmed by transmission electron diffraction patterns taken at various areas of the specimen. These orientations can be summarized as follows: Over most areas of the deformed crystal (111) planes are parallel to the surface. These areas correspond to either $- the two main defor: mation textures, the (111) [112] or the (111) [112].2-5 Within a few areas, (100) planes parallel to the surface are frequently found. These areas represent the minor deformation texture component, the (100) [Oll] type, which is derived from rotated Neumann bands.2'4'5 Only in very rare instances are (110) planes found parallel to the surface. This orientation corresponds to the very weak texture component of the (110) [001] type. In a pole figure, this (110) [0011 orientation is located within the orientation spread between the two main (111) [1121 type textures. Usually the electron diffraction patterns taken at various areas of the specimen are very simple ones, i.e., for any one area the pattern consists only of sharply defined spots of a single orientation. In some areas, however, more or less continuous rings of weaker intensities are superimposed on a simple pattern, indicating the presence of a wide range of additional orientations. In order to understand in detail the recrystallization of this cold-worked crystal, the recrywtallization characteristics of each of the various deformation texture components must be examined. This can best be done by using a high-temperature stage and transmission electron microscopy techniques, whereby small areas corresponding to the various texture components can be selected individually for examination. The present paper presents results obtained by this method. MATERIAL AND METHOD Specimens were prepared from a previously studied1 single crystal of a commercial grade 3 pct Si-Fe alloy with an initial orientation (110) [00l], cold-rolled 70 pct from 0.014 in. to 0.004 in. in thickness. Thin foils were prepared by electrolytic polishing as described in the earlier paper.' Specimens of this thin foil were then mounted in a high temperature stage similar to the one designed by Whelan.6 A direct current was used as the heating source. The temperature of the heating grid was calibrated by means of a Pt vs Pt-10 pct Rh thermocouple in a vacuum chamber (0.01 to 0.02µHg). Maximum variation within the temperature range of 250o to 000°C was about ± 25°C. After the desired areas were selected for examination, the specimen was heated to a low temperature for some time while the selected area was constantly watched. When no further change in structure and orientation could be observed, a higher temperature was applied. Photomicrographs and diffraction patterns were taken from time to time during examination, with the heater temporarily turned off* while the photographs were

Jan 1, 1962

By B. M. Bird

DURING the past four years the experimental work in coal washing carried on by the U. S. Bureau of Mines and the University of Washington has been devoted mainly to the development of special methods for the tabling of fine sizes of coals that are difficult to wash. One important outgrowth of this investigation has been the application of hindered-settling classification to coal tabling. Although used for many years in ore dressing, the term "classification" as used here may be new to many readers. It may be defined as the separation obtained when a bed of particles is held in a uniform state of suspension in an upward current of water, either continuous or pulsating, just sufficiently strong to keep the bed in a mobile condition. A common example of this type of separation is a jig in which there is no suction stroke. When the hindered-settling classifier is used with the coal-washing table, the fine-size raw coal, instead of being fed direct to tables, as is the prevailing practice, is first fed to the classifier and grouped, according to the rate of settling against the upward current of water, into perhaps six separate products. After dewatering, each of these except the sixth, a refuse product, is elevated to a seperate feed bin and washed on a separate table. This paper gives a brief discussion of the basis for the use of hindered-settling classification of a table feed; a description of the experimental work; a comparison of the results obtained with and without classification; and a discussion of the application of the classifier in commercial coal washing.

Jan 1, 1928

By AIME AIME

IN accordance with the provisions of Art. XII, See. 3, of the By-laws of the American Institute of Mining and Metallurgical Engineers, the Board of Directors hereby give notice of their intention to amend the By-laws as follows : Art. V, Sec. 2. Amend by substituting the word "senior" for ('first" before the words "Vice-president" in line two of the third paragraph of said section which relates to the calling of special meetings of the Board in the absence or disability of the President.

Jan 1, 1930

By Thomas W. Wälde

BACKGROUND Foreign investment has been a major factor in bringing about the substantial mining industries of Chile, Peru, Bolivia, Venezuela, Brasil and Guyana. But economic nationalism and sentiment against foreiqn domination of vital national industries grew in the 1960s and most major mining projects were transferred into state owner ship. Among the state mining enterprises formed were CODELCO - Chile, MINERO-PERU/ CENTRCMIN - Peru, CCMIBOL - Bolivia (in 1952), Hierro-PERU, GUY-BAU/BIDCO - Guyana, etc. New investment during that time was discouraged because it was subject to the restrictive conditions of the investment regulations of the Andean-Pact, a grouping of Chile, Bolivia, Peru, Ecuador, Venezuela and Colombia. The philisophy was that mineral resources were to be developed exclusively by national enterprises. Essential foreign inputs had to be acquired "depackaged" as separate purchases of equipment and technical assistance services. As a result of the worldwide economic recession which hit the mining industries in 1980-1982, many projects that were viable in 1970 were not developed by the new state enterprises due to lack of capital, managerial and technical abilities and due to problems with marketing. As a consequence of the long-term decline of metal prices, governments experienced difficulty in getting investment organized through national or foreign enterprises and have had to face up to the trade-offs between national control and active mineral development. A change has since taken place in governmental policies. The 1981 Peruvian mining law, the 1982 mining law of Uruguay, the 1979/1980 mineral promotion laws of Argentina, all witness the gradual shifting of emphasis from restriction to promotion. The investment rules of the Andean Pact have been progressively softened through national regulation and today are more or less irrelevant. Nationalizations and forced renegotiations have not occurred in the last few years. Countries have gone to great lengths (without much success) to re-attract foreign investment on terms that accommodate the political sensitivities of the South American countries and the practical requirements of investors and financiers. For this analysis, three contracts have been selected which reflect this accommodation in three South American countries, where miner a1 production plays a major role in the national economy. These con tracts reflect both the attitudes and traditions of the individual countries, but also mark the shift in mineral investment policies that has taken place. EL INDIO AGREEMENT The 1977 investment agreement between Chile and St. Joe Minerals marked a dramatic relationship between Chile and foreign mining investor s. In Chile, mining of copper has played a major role in the country's history. Large scale copper mining was initiated and developed by Kennecott and Anaconda. The nationalization of these two companies under the Allende government in July 1971 started a wave of nationalizations of foreign-held mining and petroleum operations since then in many parts of the world. The military government supported the new Chilean state mining companies ((30DELCO and ENMI) , but it also attempted to accelerate mineral development by prom ting foreign private investment, thus reversing the nationalistic policies followed by the Allende and the preceding Frei government. The new policy by the military government is expressed in Decreto-Ley 600 (1974) which governs foreign investment in Chile. Decreto-Ley 600 is

Jan 1, 1985

By Clyde Williams

IN this war as in no former one, the use of metals has been the major factor governing success. For building new plants, new transport facilities whether by land, sea, or air, for our mechanized army, and for nearly all weapons, iron and steel has provided the basic material. Being the world leader in iron and steel production in peacetime, we soon adapted plants to production for war. Starting with a production of 66,000,000 tons of steel ingots in 1940 from a rated capacity of 80,000,000 tons which only could be reached by straining every productive device available, our industry expanded to 86,000,000 tons in 1942, and ultimately to 96,000,000 tons. To do so required expansion of every unit operation including mining, rail and water transportation, blast-furnace and steelmaking facilities, and rolling mills. New plants not only had to be built in record time but more output for each operation was essential. This performance required skillful operation and engineering techniques and also a better understanding of the physics and chemistry underlying such complex operations as the working of a big blast furnace. A vastly increased pig iron production made possible the great output of steel by an industry that had depended on scrap for its basic raw material even though sufficient scrap was unavailable. This was done by conversion of pig iron in the Bessemer either into steel or into a low-carbon product that was subsequently used in place of scrap in the open¬hearth steel furnace. Furthermore, by duplexing from the open-hearth to the electric furnace, and the construction of many new electric furnaces, our output of electric-furnace alloy steel was greatly increased. Moreover, techniques were developed by which alloy steel could be made in the open hearth with the result that our production of alloy steel reached the fantastic figure of 15,000,000 tons a year.

Jan 1, 1945

By Bradley Stoughton

PROMINENCE has been given lately in engineering circles to the question whether an organisation with manifold interests can be as effective as one with a single aim, especially if that single aim be the furtherance of affairs of moment and the welfare of engineers in general. In its earlier days, the A. I. M. E. was forbidden by its constitution to engage in non-technical public affairs, but the members altered the constitution in this respect, in the year 1912, in response to the growing demand that engineers be more human in their interests and that the engineering societies represent them in this respect. Since that time, the activity of mining engineers in public affairs has been growing rapidly, and we are happy that the Institute has been able to render very valuable economic services. Doubtless the greatest public service rendered by engineers in a recent great emergency was the work of the Naval Consulting Board, without which the U. S. Navy would never have been able to enter promptly into service upon our entrance into the war, ,and both Navy and Army would have been a long time without the munitions that came at an early date. We can never forget that this Board was established through the direct activity of the then President of the A. I. M. E., with the hearty cooperation of other national organizations.

Jan 1, 1920

The Delegation of American Engineers constituted by the American Institute of Mining and Metallurgical Engineers, the American Society of Civil Engineers, the American Society of Mechanical Engineers, and the American Institute of Electrical Engineers, that visited France in December, 1918, in acceptance of the invitation extended by the Congrés General du Genie Civil consisted of the following: Representing the American Society of Civil Engineers, Major James F. Case, past president, Geo. F. Swain, vice-president, Nelson P. Lewis, treasurer, Geo. W. Tillson, past director, Geo. W. Fuller, director, A. M. Hunt. Representing the American Society of Mechanical Engineers, president, Chas. T. Main. Representing the American Institute of Electrical Engineers, past president, L. B. Stillwell. Representing the American Institute of Mining and Metallurgical Engineers past-president, E. C. Spilsbury. The delegation organized on the way over by the choice of Major James F. Case as chairman, and Geo F. Swain as secretary. On arriving at Bordeaux, the Delegation was met by Mr. S. D. Brown, associate member of the American Society of Civil Engineers; and on its arrival in Paris it was joined permanently by the following attaches: Captain P. Charton, of the French Engineers, Delegate of the Commissariat-General to accompany the Delegation and serve as liaison officer; Captain Carpenter of the American Army; and Mr. Geo. Herdt, representing the Society of Civil Engineers of France. The object of the visit was to discuss with the French engineers the large engineering, problems now facing France. Engineering problems in their restricted technical sense came up for discussion practically not at all, for the French do not need advice nor assistance along strictly scientific lines. It was in the -larger and economic aspects of engineering, to aid in building up the industries and commerce of France, that our French associates desired to learn from the experience of the American Delegation.

Jan 9, 1919

By K. V. S. Sastry

First attempts to apply computers for the modeling, simulation and analysis of mineral processing unit operations date back to almost twenty years. Since then substantial efforts have been directed to the development of computer software for mineral processing. Current literature indicates considerable activities in the development of computer packages for interactive and batch simulation of individual unit operations and integrated plant operations. This paper presents a comprehensive review of various simulation systems that have been described in the literature along with a discussion of present trends in the development of mineral processing simulation software. Finally, the paper includes a detailed discussion of the desirable features in future simulation packages.

Jan 1, 1984

By J. W. Koger, R. E. Hurnrnel

QUENCHED, bcc p brass, P1, transforms to a mar-tensitic phase, when it is cooled below room temperature.' This transformation can be followed using resistance measurements since the resistivity of the martensitic phase is considerably larger than that of the parent phase, Fig. 1.' phillips3 first reported that, when Cu-Zn alloys containing between 37.0 and 39.0 wt pct Zn were quenched from the 0 region to room temperature, variable amounts of a phase could be observed depending on the mode of quenching. If the quench occurs very rapidly, the a phase forms by a "massive transformation". The resultant phase has the same composition as the high-temperature P phase from which it was formed. If the quench is less severe, the alloy is retained largely in the p form; however, some a is formed by precipitation. In this case, a contains more copper than the high-temperature 0 phase from which it has formed. The a phase most probably does not undergo a transformation in the temperature range where p transforms to low-temperature martensite. This can be deduced from the Eesistivity-temperature relation which is linear in this temperature range, Fig. 2. The stable a phase which is present along with R. E. HUMMEL is Assistant Professor, Department of Metallurgical and Materials Engineering, University of Florida, Gainesville, Fla. J. W. KOGER, Junior Member AIME, formerly with University of Florida, is now with Oak Ridge National Laboratory, Oak Ridge, Tenn. Manuscript submitted December 13, 1967. IMD.

Jan 1, 1969

By J. R. Long, E. T. Hayes, R. S. Dean, F. S. Wartman

THE production of titanium in 15-1b. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,1 has provided adequate material for a study of the : physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited' and all efforts were centered on fabrication methods for those powders and the properties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. [ ] CONSOLIDATION OF THE POWDER The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at so tons per

Jan 1, 1946

By L. P. Teas

As sphalerite is such a common constituent of many types of ore, the present investigation was undertaken to determine what its relations are to the other minerals in the deposits, and also whether these are of any genetic significance. The data presented herewith were obtained from a mineralographic study of about 200 ore specimens from some 43 different localities, represented by suites of specimens in the Cornell University collection. These, grouped according to their genesis, were as follows: I. Contact-Metamorphic Deposits.-Silver City, N. M.; Kelly, N. M.; Silver Bell, Ariz.; Bingham, Utah; Agaguca, Michoacan, Mex.; Matehuala, Mex.; Sombreretti mine, Mex. II. Deep-Vein Zone Deposits.-Mineral, Louisa Co., Va.; Edwards, N. Y.; Chestnut Yard, Va.; Allah Cooper mine, Louisa Co., Va.; Globe, Ariz.; Moyie, B. C.; Rossland, B. C.; Broken Hill, N.S.W.; Weedon, Que.1 III. Intermediate-Vein Zone.-Park City, Utah; Leadville, Colo.; Butte, Mont.; Santa Barbara, Mex.; Red Cliff, Colo.; Burro Mountains, N. M.; Idaho Springs, Colo.; Blue River, Ore.; Rye, Colo.;1 Slocan district, B. C.; Freiberg, Ger.; Clausthal, Ger: IV. Shallow-Vein Zone.-Ouray, Colo.; Goldfield, Nev., Zacatecas, Mex.; Field, B. C.; Kapnik, Austria; Frontenac mine, Kingston, Ont. V. Meteoric Water Deposits.-Joplin, Mo.; Southwest, Wis.; Austinville, Va.; Crittenden County, Ky.; Ridgeburg, Pa.; Moresnet, Belgium. It is not supposed that the investigation of such a limited number of occurrences may warrant conclusive and universal generalizations, but the conclusions reached are believed to be reliable in so far as the specimens, that were examined are concerned.

Jan 11, 1917

NEW MEMBERS The following list comprises the names of those persons who became members during the period Feb. 10, 1919, to Mar. 10, 1919. ALLEN, ROLLAND CRATEN State Geol., Appraiser of Mines, Lansing, Mich. ALTMAYER, MAURICE ERNEST, Ingenieur des Arts et Manufactures, 145 Rue de la Pompe, Paris, France. AUSTIN, CHARLES L., Assayer, Highland Boy Mine, Utah Cons. Min. Co., Bingham Canyon, Utah. BARTLETT, ARTHUR J., Chief Engr., Louisville Coal & Coke Co. Goodwill, W. Va. BOIES, ORLOW W., Research Chem., Roessler & Hasslacher Chemical Co., 1632 Tenth St., Niagara Falls, N. Y. BRAGG, G. A., Mgr., Experimental Copper Leaching Plant, Mellon Inst. of Industrial Research, Thompson, Nev. BRUSCANTINI, GIOVANNI, Min. Engr., Gen'l Mgr., Sindicato Minero de Cuba, Box 370, Santiago, Cuba. COLONY, R. J Instructor in Geol., Columbia University, New York, N. Y. DAVENPORT, FRANK B., Cons. Engr., 806 Coal Exchange Bldg., WiIkes-Barre, Pa. EATON, S. FORD 120 E. 85th St., New York, N. Y. EBY, J. H., Min. Engr Box 433, Spokane, Wash. ENGELHARDT, EDWARD A., Mgr., Surinaamsche Bauxite Mij, Paramaribo, Dutch Guiana, S. A.

Jan 4, 1919

By Robert W. Thomas

LEACHING of mined-out areas at the Arizona property of the Ray Mines Division, Kennecott Copper Corp., was started on Jan. 20, 1.937, and by July 1, 1938, 10,000,000 lb. of copper had been produced by this method. Leaching operations at present are confined to the western portion of the ore body and over an area of approximately ten acres. The ore in this area was extremely high in pyrite and the copper content, which averaged slightly in excess of 1 per cent, was the result of incomplete secondary enrichment by solutions which apparently worked laterally from the main ore body. Above the ore was an unaltered zone of primary or protore averaging 125 ft. in thickness and containing approximately 0.6 per cent copper. Above this was the capping or leached zone averaging 50 ft. thick.

Jan 1, 1938

By F. B. Foley

A description of tests made by a committee of the Division of Engineering of the National Research Council to determine whether velocity of impact affects the formation of Neumann bands. FOREWORD Not infrequently, in the case of the failure of a metal structure, such as a bridge, tank, airplane, gun carriage, etc., a doubt arises whether the failure was due, among other causes, to the effect of an overburden or of an explosive maliciously or accidentally exploded in contact with it. As few means of discriminating between the effects of these causes have been known and these means were of a rough qualitative character, it was surprising to find in the record of an inquiry into the failure of a structure, the statement that, by observations on the Neumann bands in the structure, it was possible to determine the speed of breakage in the metal and to distinguish between a fracture caused by an explosion and one caused by an ordinary mechanical strain. Such a criterion, if well proved, was of value to the explosives experts of the Bureau of Mines, the Ordnance Department of the United States Army and the Bureau of Ordnance of the United States Navy, but search showed no record of it in the literature nor did any of the metallurgists and metallographers consulted know of any data on which such a criterion could be based having been assembled and critically studied. However, it was universally held that there was promise in the idea and that there existed unique facilities at the Bureau of Mines Experiment Station at Pittsburgh for the preparation, under definitely known conditions, of material for study by metal-lographers, and that material of value might also be obtained from the proving grounds of the Army and Navy. Therefore, with the approval of the Director of the Bureau of Mines and the Chiefs of Ordnance of the War and Navy Departments, the Chairman of the Division of Engineering of the National Research Council, on April 12, 1919, appointed a Committee on the Investigation of Neumann Bands, which has since been engaged in this study and which, after some slight change in its personnel, consists now of the following: Dr. William Campbell, Advisory Metallurgist, Bureau of Ordnance, Navy Department. F. B. Foley, Metallurgist, Bureau of Mines. S P. Howell, Explosives Engineer, Bureau of Mines. Comdr. O. M. Hustvedt, U. S. N., Bureau of Ordnance, Navy Department. Dr. Charles E. Munroe, Chief Explosives Chemist, Bureau of Mines.

Jan 9, 1922

By M. A. Mahtab, T. M. Yegulalp

This paper presents the development and application of an approach for clustering fracture orientation data. Data are projected on the surface of the unit upper hemisphere and the clustering approach is applied in three steps: (1) randomness test and identification of dense clusters, (2) estimation of cluster statistics, using Bingham distribution, and (3) rejection of extremal data based on Chauvenet's criterion.

Jan 1, 1982

By P. Hudock

Thin films of PbS and CdS have been deposited on insulutiug- sapphire substrates by euzploying a subliwzation technique rising near-equilibriurum conditions in ultrahigh vacuum. Oriented polycrystalline PbS and CdS films on sapphire have mobilities approachitzg values characteristic of bulk crystals. In the case of CdS, special purification procedures were crucial in obtaining high-mobility films. By performing the depositiotz of a compound within a small chamber heated to a UNiform temperature within a Vacuum systerrz, it is possible to approach equiilibrium cod-tions r.~litl~irs the chamber. In this way; the sublimation and condensation proceed under near equilibrium co?zditions, and it was found that the properties of dePosited corrzpounds were similar to those of the source material. Oriented PbS films on sapphire have a roor?l- temperature unobility of 700 sq cm per v sec and a T-5/2 temperature dependence characteristic of bulk crrystnls. CdS layers on sapphive Izazse a resistivity ~uhich is corrlpamble to the resistivity of the souvce crystals over a range of four ordem of rrlagnitude. Irz contrast, Ihe resistivity of CdS films prepared by conventional evaporation depends largely upon the substrate terrzperat~ire and postheating treatrrletlt, vather than upon the properties of' the solirce rrraterial. In the case oj the CdS films the achievment of high carrier mobility required the cargful exclusion of cont~~~~ii~unts from the films. The steps taken to accomplish this included presublimation of the source material, performance of the deposition at a backg-m~ozd pressure less than 10-8 Torr, and a solvent extraction with liquid cadminum, similar to that described by Aven and woodbury. The deposition of ,films under near-equilibrium conditions is being op-plied to other classes oj COmpounds. II should he of 1:allce ,tor llle deposition of nny matevial that decomposes in the vapor state. THIN films of PbS and CdS have been deposited on insulating sapphire substrates by employing a sublimation technique using near-equilibrium conditions in ultrahigh vacuum. Oriented polycrystalline PbS and CdS films on sapphire have Hall mobilities approaching values characteristic of bulk crystals. In the case of CdS, special purification procedures were crucial in obtaining high-mobility films. Depositions were performed in a small quartz sublimation cell shown in Fig. 1 that contained the compound and the single-crystal sapphire substrate. The substrates were etched in tapered solutions of hot phosphoric acid, rinsed in deionized water, dried, and transferred to the cell under dry nitrogen. Graphite crucibles and substrates were used in experiments where it was necessary to provide an inert test vehicle for the analytical determination of impurities in the source crystals and deposited films. The crucibles and substrates were machined out of spectrographic-grade graphite having less than 1 ppm of impurities. A quartz mask was sometimes used to define a pattern which could be used for Hall and resistivity measurements. Close spacing between the compound and substrate was maintained to insure better transport of each component from the source material.

Jan 1, 1968

By B. F. Buie

Included in the general category of clays is a large and varied assemblage of nonmetallic silicate minerals which characteristically occur as fine-grained particles having flaky, sheetlike, or rod-shaped form. Most, though not all, are hydrous aluminum silicates. Amount and kind of impurities vary greatly, and these strongly influence the uses of the various clay types. Clays occur in a wide range of geological situations: as bedded sedimentary deposits composed of the weathering products of feldspar and other minerals; as alteration products of igneous, sedimentary, and metamorphic rocks weathered or hydrothermally altered in place; and, to a more limited extent, as hydrothermally introduced materials. TYPES AND MARKETS On the basis of chemical composition and crystal structure, two major groups of clay minerals recognized are the "kandites" or kaolin group, and the "smectites" or montmorillonite group. Another major type is illite, particularly important as a constituent of shales. Two additional mineral species having economic importance are attapulgite (palygorskite) and sepiolite. For present purposes, however, a classification based on utilization is more appropriate. The U.S. Bureau of Mines recognizes six types of clay: kaolin, ball clay, fire clay, bentonite, fuller's earth, and miscellaneous clay. Kaolin The kaolin group of minerals consists of the mineral species kaolinite, halloysite (metahalloysite), dickite, and nacrite, although the latter two are not being produced commercially. Kaolin, also called china clay, is a high-purity white material. Perhaps it is best known as a principal ingredient in the manufacture of chinaware, porcelain, and other high-quality ceramic products. However, by the mid-1970s very close to 50% of the kaolin produced in the United States was going to the paper industry for use as a filler and coating material. Manufacture of refractories uses about 12% of U.S. production. Kaolin is also used in plastics, in the rubber industry as a filler in footwear, electrical cable, and similar products, and as a conditioner of rubber for automobile tires to add strength and abrasion resistance. Smaller amounts are used in printing ink, paint, and adhesives; as insecticide carriers; in the production of catalysts for the petroleum refining industry; and in many other industrial and commercial applications. Production and use of kaolin in the United States doubled in the ten years from 1946 to 1956, and doubled again by 1966. Growth continues at a rate of about 7 % per annum.

Jan 1, 1976

H. McD. Lorain says in regard to his son, Captain S. H. Lorain; "It might be of interest to you to know that, although but 23 years of age, my son is captain of Co. C 107th U. S. Engineers, Thirty-second Division. He landed in France about the middle of February, 1918, and was commissioned a captain on Sept. 5, 1918. He started for the front the latter part of June and was there continuously until the armi-stice was signed, on Nov. 11, being on the front lines in the Argonne at that time. He is, at present, in Coblenz, Germany, with the Army of Occupation. Although much of his work was clone under artillery and machine-blur fire, as well as airplane bombs and fire, he escaped without a scratch. Once, he was the only one of a group who escaped without a scratch from an exploding shell." Lieut. Bernard H. Lasky, on a post card received a short time ago, gave the following brief record of his military career. "I have been serving with the 316th Engineers in France and in Flanders and had the satisfaction of being in the last big drive in Belgium which sent the enemy beyond Avaenarde and did much to increase their gait on their way to Brussels. On Oct. 1, I received a commission as second lieutenant and was assigned to Co. C of the 316th Engineers."

Jan 3, 1919

By D. A. Belforti, M. P. Lepie

Spectroscopically pure copper was melted on sapphire plaques in a zydrogen atmosphere. The surface tension of the liquid metal was determined using the sessile drop technique. Measurements were made by direct observation with the aid of a specially const,mcted telescope. The value obtained, 1268 dynes per cm, is compared to that found in the literature. THERE is at this time considerable interest in the use of ceramics for vacuum tubes. The crystalline material is superior to the more conventional glass in mechanical strength, chemical inertness, dielectric properties, ability to withstand high temperatures, and so forth. However, ceramics are much more difficult to seal hermetically with metals than are the glasses. For this reason an investigation was undertaken to determine the wetting and adhesion of metals to ceramics. The sessile drop technique offers a convenient means at elevated temperatures for measuring liquid surface tension, wetting angle, density, spread- ing coefficient, and work of adhesion. Thus, from the contour of a drop of liquid at rest on a solid surface one can obtain a quantitative evaluation of the degree to which the two substances will bond. To this end a special apparatus was constructed so that various molten metals could be observed. Standardization of the apparatus was done initially by measuring the surface tension of copper since this is well documented in the metallurgy literature. Although there are many methods available for the measurement of surface energy,'+ the sessile drop technique has been used most extensively for molten metals and ceramics.5"' Fig. 1 illustrates the dimensions to be measured. From these values, the surface tension of the liquid can be obtained using the Bashforth and bdams' equation and tables.

Jan 1, 1963