Search Documents

By Richard H. Terhune

Slag and matte, in lead and copper smelting, are, for convenience of removal, tapped into pots of small capacity, usually of paraboloid form, of cast-iron, weighing 275 to 300 pounds, and holding the same weight of slag. As in many smelting districts one ton of ore makes a ton and a quarter of slag, a large number of pots is needed to equip an ordinary plant. Sudden and frequent expansion of the solid bowl causes the pots to crack at the bottom in a few months, and the matte, a very fluid sulpliide, enters these rough fissures and speedily corrodes its way through the vessel. 1 find, from one year of practice with a slag-

Jan 1, 1887

By H. W. Rogers

THE first steam shovels used in this country were built by the Otis Company, of Boston, about 50 years ago, but as they were of very crude construction and rather unsuccessful only a few were built. For possibly 10 years prior to 1884 successful steam shovels were made and used on certain classes of work, but it was not until that time that they were manufactured in quantities and began to play an important part in all classes of excavation. From that time up to the present day there have been gradual but continuous improvements on the original shovel, not only in the mechanical construction, but also in the design of boilers and engines which are best adapted to this class of service. In proposing a change from steam to electric operation we have to deal with a steam equipment which has not only proved its worth but has probably reached its highest stage of development and efficiency. That the electric shovel is a possibility cannot be denied, as at present from 12 to 18 shovels are in operation in this country. These shovels may be divided into three classes: the friction electric, which is operated by a single constant-speed motor with friction clutches; the three or four motor direct-current equipment, and the three or four motor alternating-current equipment. It is the second and third classes that I wish to deal with, as the first class does not compare favorably with the steam shovel so far as speed is concerned, although it may be operated as cheaply. There is probably no other class of machinery that presents a duty cycle as severe as that of the shovel, which is very short, varying from 7 to 12 sec. on the hoist, from 7 to 12 sec. on the thrust, and from 10 to 18 sec. on the swing, making a complete cycle in from 17 to 30 sec., and the motor to meet these requirements must have a sufficiently low armature inertia to permit of rapid acceleration and quick reversals under small power. It should also be a motor of rugged design, as it must be subjected to severe overloads and shocks and frequent reversals. This is especially true of the hoist motors and, to a lesser degree, of the swing motor; the thrust motor being practically stalled during the digging operation, although it may revolve or overhaul, according to conditions, and is operated at full speed only after the hoisting operation is completed.

Jan 2, 1914

By S. J. Leach

The possible solution of some of the problems raised in H. L. Hartman's article "Determining Ventilation Requirements for Continuous Miners," which appeared in the March 1962 issue of MINING ENGINEERING, is offered by recent investigative work done at the Safety in Mines Research Establishment, Ministry of Power, Sheffield, England. Highlights of this research are outlined here. Accumulations and layers of methane form in a mine roadway because it is difficult to mix methane with air beneath it by turbulent diffusion. Such mixing involves work contrary to buoyancy forces. In specifying requirements for good ventilation it is not, therefore, sufficient to state that the airflow must be turbulent in the absence of methane. Fundamental work at SMRE on the behavior of methane roof layers has led to the formulation of rules for controlling methane roof layers which specify the ventilation velocity needed to ensure adequate mixing in terms of the rate of flow of methane into the layer (V = cu ft per min) and the airway width (D = ft). A "layering number" for methane and air has been defined by [U37/V/D] where U is the mean ventilation velocity in ft/min in the upper half of the airway. In a horizontal airway there is no mixing by turbulent diffusion for values of the layering number less than about 2, resulting in extensive roof layers. But with a layering number of 5, the layer is "brought under control"-i.e., a further increase in the layering number will shorten the length of the layer only slightly, and a small decrease in the layering number will cause only a small increase in the length of the layer. In a sloping roadway with uphill ventilation, higher values of the layering number are needed to achieve this "controlled" condition; the values range from about 5 at small slopes to about 8 at a slope of 1: 10. In downhill ventilation it is possible for layers to "back" against the ventilation, i.e., to flow uphill. The critical condition for preventing backing can also be expressed in terms of the layering number. Backing will be prevented if layering numbers are about 3 for small slopes and about 4.5 for large slopes; these values for downhill ventilation also give good control of the layer.

Jan 10, 1962

By A. G. H. Andersen, A. W. Kingsbury

SILICON bronzes containing iron are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith' and of A. G. H. Andersen .2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 determined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at 1100°C. Hanson and Ford," using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. Of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West7 have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,1,2,7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. PREPARATION OF SAMPLES Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates h in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1942

By Donald A. Brobst

The minerals barite (BaSO4 barium sulfate) and witherite (BaCO3 barium carbonate) are the chief commercial sources of the element barium and its compounds whose many uses are nearly hidden among the technical complexities of modern industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry which in 1973 consumed at least 80% of the world's produc¬tion of 4.4 million tons as a major ingredient of the heavy fluid, called mud, that is circulated in rotary drilling of oil and gas wells. The re¬maining 20% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite occurs throughout much of the world and is available from three major geologic types of deposits-vein and cavity fill¬ing, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world's demand for barite is expected to increase, and geologic circumstances are favor¬able for the discovery of new deposits of com¬mercial value. Witherite is much less common and abun¬dant than barite, although it is more desirable in many ways as a raw material for the pro¬duction of barium chemicals. The United States has not produced witherite since about 1950; England is currently the chief producer of witherite. End Uses Most of the world's barite production since 1926 has been used as a weighting agent for the muds circulated in rotary drilling of oil and gas wells. The muds fundamentally are mixtures of water, clay, and barite in different proportions that vary according to local reservoir condi¬tions. Muds with a specific gravity as great as 2.5 are used. The mud is pumped down the hollow drill stem, passes through the bit at the bottom of the hole, and rises to the surface in the space between the drill stem and the wall of the hole. In the course of this circulation the drill bit is cooled, cuttings are removed, the drill stem is lubricated, the walls of the hole are sealed, and the hydrostatic head of the column of weighted fluid helps to confine high oil and gas pressures. The latter feature aids in prevention of gushers, thus reducing both environmental pollution and waste of oil and gas resources as well as conserving the natural reservoir pressure for greater production and rate of recovery of the products contained in the rocks. Barite is particularly well suited for drilling mud because it is clean, easy to handle, soft (nonabrasive), heavy, virtually inert chemi¬cally, and relatively inexpensive compared to many other available heavy materials. Barite is used in the manufacture of glass in continuous tanks. The addition of barite ho¬mogenizes the melt and gives greater brilliance and clarity to the finished glass. Ground barite, both unbleached and bleached by sulfuric acid, is a common industrial filler, extender, and weighting agent. The rubber in¬dustry is a major consumer of barite as a filler. Barite also is added to bristolboard, heavy printing paper, playing cards, rope finishes, brake linings, clutch facings, plastics, and li¬noleum, to name but a few uses. Bleached barite has long been an extender in white lead paint because of its weight. The low index of refraction of barite, however, makes its ability to cover marks poorer than some other sub¬stances, but its low capacity for absorption of oil is a good feature. Off-color or unbleached barite can be used as a filler in colored paints. In the construction industry, some lump barite is used in concrete aggregate to weight down pipelines buried in marshy areas and to shield nuclear reactors. Because barite absorbs gamma radiation well, its use reduces the amount of expensive lead shielding otherwise

Jan 1, 1975

By Philip B. Bucky

[ ] FOREWORD THIS symposium brings together points of view, experiences and ideas on rock bursts from a goodly portion of the globe. Some conceptions, particularly those regarding the necessity of depth, have been fairly well shattered, as we find that they are present in the water tunnels of New York, on the surface at marble quarries in Vermont, and in the coal mines of the United States, as well as in the deep mines of the South African and Kolar gold fields, and in the nickel, copper and gold mines of Canada. Their occurrence under such a variety of conditions is, therefore, a challenge,

Jan 1, 1942

By Jay A. Carpenter

IN six years the construction of Hoover Dam and the power plants probably will have reached the operating stage and this vast new source of power will then be continuously available for industry. The height of the darn will be 580 ft. and the average annual flow of the Colorado River is calculated at approximately 24,000 cu.ft. per sec. If this full head and average flow can be maintained the year round, about one million horsepower will be generated. The U. S. Reclamation engineers, taking into consideration the probable range in flow and head, have set the figure for power contracts at 660,000 firm horsepower, which can be assured at all times of the year. During the months of heavy run-off of water from the Colorado River Basin the power plants should be able to generate the full 1,000,000 hp. capacity of the power plants, so there will be 340,000 excess or secondary horsepower. The cost of firm power at the switchboard will be close to 2.15 mills per kw.-hr., equal to $14.05 per hp.-yr., and the cost of the secondary or off-peak power will be close to 0.8 mills per kw.-hr., or $5.22 per hp.-yr. In no place in the country can such cheap power be obtained today. The electrochemical industry is in a state of flux because the power costs from its old sources have increased so much (to $30 per hp.-yr. at Niagara) that the industries have had to seek new sources, so they have gone to Canada and Norway and built new plants.

Jan 1, 1932

By A. D. Mutch

This contribution is prompted by the fact that the writer has recently published an article" which has in part the same general conclusions as B. S. Butler's, namely, the form of the standard mineral paragenesis in hypogene deposits and the parallel transition from early high temperature acid to late low temperature alkaline or neutral solutions. Since the writer also recognizes that he is not fully qualified to discuss the formation of ore deposits as a chemical problem, this discussion will be limited to summarizing other observations and will suggest how Butler's Table II might be made more effective. The form of Butler's table is not unlike that widely used by European geologists30 in which the various minerals are related to the types of ore fluids-pegmatitic, pneumatolic and hydrothermal. Thus the decrease in temperature and change in pH of the ore- bearing fluids as recognized by Butler may also be paralleled by perhaps even greater changes in composition, density, and character.

Jan 5, 1958

By Edward Judd

CANADA'S mining industry is rapidly recovering from the depression through which it passed in 1921. Its total output of $183,029,600 in 1922 was 6.4 per cent. greater than that of 1921, and was exceeded by only three previous years, 1917, 1918, and 1920. Table 1 compares the output of a few of 'the more important items selected from preliminary data published' by the Dominion Bureau of Statistics. TABLE 1.-OUTPUT OF CERTAIN MINERAL PRODUCTS IN CANADA PER CENT. 1921 1922 CHANGE Cobalt, metal and in compounds, lb 252,000 443,800 +76.1; Copper contents of blister, matte, and exported ores, lb 47,620,820 43,321,400 - 9.0 Refined copper, lb 4,286,000 730,000 -83.0 Gold, fine oz 926,329 1,230,985 +32.8 Pig iron, sh. tons 665,676 429,024 -35.5 Lead, sh. tons 33,340 47,085 +41.2 Nickel contents of matte, etc., lb. 19,293,060 17,496,490 - 9.3 Silver, including that in base bullion, gold bullion, etc., fine, oz. 13,543,198 17,611,646 +30.0 Zinc (nearly all refined), sh. tons. 26,545 28,199 + 6.2 Asbestos shipments, sh. tons 92,761 136,657 +47.3 Coal, all grades, sh. tons 15,057,500 15,045,300 Gypsum shipments, sh. tons 386,550 441,160 +14.1 Natural gas, M. cu. ft 14,077,600 14,954,100 + 6.2 Petroleum, bbl : 187,540 178,570 - 4.8 Cement, bbl 5,752,885 6,943,968 +21.0 Brick, structural, all kinds, M. , , 109,009 127,137 +17.0 On the basis of estimated market values, the whole output of 1922 was contributed as follows: Metals, 33.4 per cent.; non-metallic minerals, 45.1 per cent.; structural materials and clay products, 21.5 percent.; this distribution indicates a return of the metal mining. industry nearly to the position of relative importance that it occupied. before 1921, in which year metals contributed only 28.7 per cent. to the total value. of output while non-metallics gave 51.1 per cent. Canadian cobalt originates entirely in the ores of the Cobalt district, which are mainly treated at smelters in southern Ontario, although some quantities of residues have been exported to England and Europe. Exports during 1922 increased even more than production, consisting of about four-fifths . cobalt oxides and salts, and one-fifth of cobalt alloys and other metal combinations.

Jan 8, 1923

By O. C. Wheeler

In order that the series of reports on oil and gas in Colombia may be complete, the report for the year 1941, which was not available for Volume 160 of the TRANSACTIONS, is given here. The report for 1945 begins on page 4o6.

Jan 1, 1946

By Robert S. Shoemaker

Recently we read a short article which stated that Marcona Corp. was studying the use of 25,000-hp autogenous grinding mills for an iron ore project in Alaska. As if that weren't enough, they were going to dispense with the primary crusher and feed run-of-mine ore to the grinding mills which were to be driven by wrap-around seven-cycle motors. We see also that Bougainville Copper Co. will be grinding 90,000 tpd of ore in only eight 4250- hp ball mills. At Bougainville too, their float section will be the first large one to be completely equipped with the new 350-cu ft flotation cells. After a half century of relatively peaceful growth in the minerals industry, we are now seeing almost exponential advances in both equipment and plant size. At the same time, we are seeing a constant blending of hydro and pyrometallurgical techniques and processes into minerals beneficiation until the sample grind-'em-up-and-concentrate-'em plant is becoming a rarity.

Jan 1, 1970

By Benjamin C. Craft

A review of development in North Louisiana during 1936 centers around the Rodessa field, in Caddo Parish. Continued extension of the

Jan 1, 1937

By Louis A. Carapella, William E. Shaw

MAGNESIUM and its alloys have long been characterized as possessing limited capacity for mechanical forming at atmospheric temperatures prior to rupturing despite their outstanding performances in this respect at elevated temperatures. Responsible for this behavior are the fundamental facts that these hexagonal-type metals have comparatively few slip elements at low temperatures for any extensive deformation and that, at high temperatures, additional slip elements become operative, thus enhancing greater plasticity under strain. The transitional point has been set at 225°C by Schmid1 for single crystals, and at 250°°C by Morell and Hanawalt2 for extruded magnesium metal. In a recent X-ray investigation on polycrystalline magnesium-alloy sheets, Barrett and Haller3 have revealed that, below the transitional temperature, the initial plastic deformation proceeds mostly by a twinning action; that, above such a temperature, the action is mostly by slip. The deep-drawing performance of the magnesium + 1.5 pct alloy sheett over a wide range of temperatures has been investigated by Weber and Vanden Berg,' and their results are presented in Fig r. It should be noted from this work that a maximum drawability of about 25 pct at room temperature has been obtained on this alloy under the conventional deep-drawing operations. For the same alloy, it is now possible to augment the cold drawability to about 40 pct by a process to be disclosed. Hitherto, this value has been obtained only by deep-drawing the alloy at around 230°C. That greater plastic flow is attainable at atmospheric temperatures on magnesium under certain deformational techniques was discovered by the authors6 in their analyses of plastic-deformational behaviors of pure magnesium. This fact is best illustrated in Fig 2 from the Hargreaves analysis6 performed by the authors under two different modes of loading. For direct test, a separate unstrained specimen was used for each load duration, whereas for the integrated test the same specimen was employed for all the five intermittent loadings so that the load duration was made additive throughout the investigation. The higher plastic flow-rate at room temperature, as designated by the Hargreaves constant S, was obtained by the integrated or intermittent loading procedure. The authors5 in further tests showed that, under such a procedure greater plastic flow was also realized with a progressive increase in deformational loads. These findings have been applied

Jan 1, 1947

By Bunting S. Crocker

PEBBLE grinding at Lake Shore is not a temporary wartime substitute. The tube milling plant, with a 1000 ton per day capacity, grinds a hard siliceous ore to 90 pct - 325 mesh. The plant, prior to using pebbles, was consuming 4.3 lb of 1 1/4-in. grinding balls per ton of ore, which amounted to 785 tons of balls per year. At September 1951 prices, $132.60 per ton, this steel cost amounted to, $104,400 per year, or $0.285 per ton milled. By the Lake Shore method of substituting screened rock for this steel, all of this cost is saved. This is one of the major economies in Lake Shore mill practice. Regardless of the ultimate price of grinding balls, a change, back to steel balls is not considered. The present pebble plant is more flexible than a steel ball plant and equally efficient. For example, if it is desired to change the size of grinding media, the pebble charge in any mill can be changed completely in 4 to 5 days, as against 76 days to change completely a 1 1/4-in. steel ball charge. To change pebble size it is necessary only to change two sets-of screens and clean out the rock feed storage bin. This will take 8 to 10 days as against 3 to 4 months to clean. out the customary supply of grinding balls kept on hand. Also it has not always been ' possible to purchase all desired sizes of balls at any price. In an analysis of savings effected by the use of the pebble mills, the flexibility of the Lake Shore grinding plant should be discussed, as it has a direct bearing on these savings. The plant has always used several units to handle tonnage rather than sending all the tonnage through a single unit. This principle may result in using small diameter mills, but no objection to that is seen. At no time has any advantage been found in cost per ton ground in large diameter mills. Both the capacity and the power of any mill varies as the diameter raised to the 2.6th power. Consequently large or small mills are equally efficient, and a plant should be designed to use as many units-or combination of units as is consistent with reasonable operating practice. Mills under 5 ft diam are harder to reline, etc. To define the case at Lake Shore, .2600 tons per day formerly were milled in seven 7x6-ft ball mills and twelve 5x16-ft (and two 6x16-ft) tube mills.* This gave an excellent test plant. and an extremely efficient-one. In this plant the ratio of ball mills to tube mills was 1: 2. When the much cheaper pebble mills were substituted for the tube mills, this. ratio -was changed to one ball mill to four pebble mills to take the greatest possible advantage of the cheaper operating mill, i.e., the pebble mill. This flexibility without loss in efficiency has been an important item in the cost savings. It is interesting to note that the use of pebbles for fine grinding was. proved first in the laboratory in a 12-in. ball mill. In fact, since 1934 all testing on -.8 mesh material has been done in this 12-in. mill. Scope of the Tests A paper on fine grinding at Lake Shore Mines was published in July 1940.1 This paper covered 7 years of intensive research on fine grinding as well as sizing methods and equipment, plant scale grinding tests on 5x16-ft tube mills with and without .grate discharges-both with 1 1/4-in. and 3/4-in. balls, the use of laboratory mills to evaluate plant changes, and several reports on classifiers and classification. In the following July the addendum report' was added in which the idea of series-circuit grinding was introduced, and the results of running five stages of tube mills and bowl classifiers were shown. Since 1940, the ball milling end of the plant has been altered extensively as a result of tests on the use of 3 1/2-in. rods in 7x6-ft mills and the use of the Tyler repulping screen with from 7 to 14 mesh screens. These tests are, lengthy and may be covered in a separate 'report later. The scope of this report is confined to ore ground by rod milling and ball milling until it passed through an 8 mesh Tyler Ty-rod screen. The -8 mesh screen undersize then was pumped to a primary bowl classifier in open circuit and the sands .from the bowl sent to the primary pebble mills, see Fig: 1. In the pebble mill circuit the ore is ground to 90 pct -325 mesh (24 pct + 28 microns) In studying the flowsheet, attention should be paid to the efficiency of the classification equipment used. The Tyler repulping screen is an efficient machine on the 8 to 10 mesh separation, and the bowl classifier is equally efficient at the 325 mesh separation. Efficient classification is a necessity for series-circuit stage grinding. The ore is hard siliceous porphyry, 60 pct SiO2, 80 pct insoluble. Its grindability at different. meshes has been shown near the top of 'the list in F. C. Bond's grindability tests' Lake Shore is not shown, but an adjacent-mine with identical ore, Wright-Hargreaves, is. Reasons for the-Changeover Since 1936 grinding balls have been rising steadily in price with no sign of stopping. For a mill that used 4.5 to 5.2 lb of grinding balls for every ton of ore ground this rise represented an alarming increase in grinding costs. In many cases the quality of the grinding balls fell off as the scrap steel became more difficult to obtain. The ratio of tube mills to ball mills increased with the use of the Tyler repulping screen in the ball mill circuit. Originally only 3.0 lb of balls per ton were used in the tube mills, and this

Jan 1, 1952

By Bunting S. Crocker

EBBLE grinding at Lake Shore is not a temporary BlE wartime substitute. The tube milling plant, with a 1000 ton per day capacity, grinds a hard siliceous ore to 90 pct — 325 mesh. The plant, prior to using pebbles, was consuming 4.3 lb of 11/4-in. grinding balls per ton of ore, which amounted to 785 tons of balls per year. At September 1951 prices, $132.60 per ton, this steel cost amounted to $104,400 per year, or $0.285 per ton milled. By the Lake Shore method of substituting screened rock for this steel, all of this cost is saved. This is one of the major economies in Lake Shore mill practice. Regardless of the ultimate price of grinding balls, a change back to steel balls is not considered. The present pebble plant is more flexible than a steel ball plant and equally efficient. For example, if it is desired to change the size of grinding media, the pebble charge in any mill can be changed completely in 4 to 5 days, as against 76 days to change completely a 1-in. steel ball charge. To change pebble size it is necessary only to change two sets of screens and clean out the rock feed storage bin. This will take 8 to 10 days as against 3 to 4 months to clean out the customary supply of grinding balls kept on hand. Also it has not always been possible to purchase all desired sizes of balls at any price. In an analysis of savings effected by the use of the pebble mills, the flexibility of the Lake Shore grinding plant should be discussed, as it has a direct bearing on these savings. The plant has always used several units to handle tonnage rather than sending all the tonnage through a single unit. This principle may result in using small diameter mills, but no objection to that is seen. At no time has any advantage been found in cost per ton ground in large diameter mills. Both the capacity and the power of any mill varies as the diameter raised to the 2.6th power. Consequently large or small mills are equally efficient, and a plant, should be designed to use as many units or combination of units as is consistent with reasonable operating practice. Mills under 5 ft diam are harder to reline, etc. To define the case at Lake Shore, 2600 tons per day formerly were milled in seven 7x6-ft ball mills and twelve 5x16-ft (and two 6x16-ft) tube mills.* This gave an excellent test plant and an extremely efficient one. In this plant the ratio of ball mills to tube mills was 1:2. When the much cheaper pebble mills were substituted for the tube mills, this ratio was changed to one ball mill to four pebble mills to take the greatest possible advantage of the cheaper operating mill, i.e., the pebble mill. This flexibility without loss in efficiency has been an important item in the cost savings. It is interesting to note that the use of pebbles for fine grinding was proved first in the laboratory in a 12-in. ball mill. In fact, since 1934 all testing on — 8 mesh material has been done in this 12-in. mill. Scope of the Tests A paper on fine grinding at Lake Shore Mines was published in July 1940.' This paper covered 7 years of intensive research on fine grinding as well as sizing methods and equipment, plant scale grinding tests on 5x16-ft tube mills with and without grate discharges both with 1-in. and -in. balls, the use of laboratory mills to evaluate plant changes, and several reports on classifiers and classification. In the following July the addendum report2 was added in which the idea of series-circuit grinding was introduced, and the results of running five stages of tube mills and bowl classifiers were shown. Since 1940, the ball milling end of the plant has been altered extensively as a result of tests on the use of 3-in. rods in 7x6-ft mills and the use of the Tyler repulping screen with from 7 to 14 mesh screens. These tests are lengthy and may be covered in a separate report later. The scope of this report is confined to ore ground by rod milling and ball milling until it passed through an 8 mesh Tyler Ty-rod screen. The —8 mesh screen undersize then was pumped to a primary bowl classifier in open circuit and the sands from the bowl sent to the primary pebble mills, see Fig. 1. In the pebble mill circuit the ore is ground to 90 pct —325 mesh (24 pct + 28 microns). In studying the flowsheet, attention should be paid to the efficiency of the classification equipment used. The Tyler repulping screen is an efficient machine on the 8 to 10 mesh separation, and the bowl classifier is equally efficient at the 325 mesh separation. Efficient classification is a necessity for series-circuit stage grinding. The ore is hard siliceous porphyry, 60 pct SiO,, 80 pct insoluble. Its grindability at different meshes has been shown near the top of the list in F. C. Bond's grindability tests.' Lake Shore is not shown, but an adjacent mine with identical ore, Wright-Hargreaves, is. Reasons for the Changeover Since 1936 grinding balls have been rising steadily in price with no sign of stopping. For a mill that used 4.5 to 5.2 lb of grinding balls for every ton of ore ground this rise represented an alarming increase in grinding costs. In many cases the quality of the grinding balls fell off as the scrap steel became more difficult to obtain. The ratio of tube mills to ball mills increased with the use of the Tyler repulping screen in the ball mill circuit. Originally only 3.0 lb of balls per ton were used in the tube mills, and this

Jan 1, 1953

By Bunting S. Crocker

EBBLE grinding at Lake Shore is not a temporary BlE wartime substitute. The tube milling plant, with a 1000 ton per day capacity, grinds a hard siliceous ore to 90 pct — 325 mesh. The plant, prior to using pebbles, was consuming 4.3 lb of 11/4-in. grinding balls per ton of ore, which amounted to 785 tons of balls per year. At September 1951 prices, $132.60 per ton, this steel cost amounted to $104,400 per year, or $0.285 per ton milled. By the Lake Shore method of substituting screened rock for this steel, all of this cost is saved. This is one of the major economies in Lake Shore mill practice. Regardless of the ultimate price of grinding balls, a change back to steel balls is not considered. The present pebble plant is more flexible than a steel ball plant and equally efficient. For example, if it is desired to change the size of grinding media, the pebble charge in any mill can be changed completely in 4 to 5 days, as against 76 days to change completely a 1-in. steel ball charge. To change pebble size it is necessary only to change two sets of screens and clean out the rock feed storage bin. This will take 8 to 10 days as against 3 to 4 months to clean out the customary supply of grinding balls kept on hand. Also it has not always been possible to purchase all desired sizes of balls at any price. In an analysis of savings effected by the use of the pebble mills, the flexibility of the Lake Shore grinding plant should be discussed, as it has a direct bearing on these savings. The plant has always used several units to handle tonnage rather than sending all the tonnage through a single unit. This principle may result in using small diameter mills, but no objection to that is seen. At no time has any advantage been found in cost per ton ground in large diameter mills. Both the capacity and the power of any mill varies as the diameter raised to the 2.6th power. Consequently large or small mills are equally efficient, and a plant, should be designed to use as many units or combination of units as is consistent with reasonable operating practice. Mills under 5 ft diam are harder to reline, etc. To define the case at Lake Shore, 2600 tons per day formerly were milled in seven 7x6-ft ball mills and twelve 5x16-ft (and two 6x16-ft) tube mills.* This gave an excellent test plant and an extremely efficient one. In this plant the ratio of ball mills to tube mills was 1:2. When the much cheaper pebble mills were substituted for the tube mills, this ratio was changed to one ball mill to four pebble mills to take the greatest possible advantage of the cheaper operating mill, i.e., the pebble mill. This flexibility without loss in efficiency has been an important item in the cost savings. It is interesting to note that the use of pebbles for fine grinding was proved first in the laboratory in a 12-in. ball mill. In fact, since 1934 all testing on — 8 mesh material has been done in this 12-in. mill. Scope of the Tests A paper on fine grinding at Lake Shore Mines was published in July 1940.' This paper covered 7 years of intensive research on fine grinding as well as sizing methods and equipment, plant scale grinding tests on 5x16-ft tube mills with and without grate discharges both with 1-in. and -in. balls, the use of laboratory mills to evaluate plant changes, and several reports on classifiers and classification. In the following July the addendum report2 was added in which the idea of series-circuit grinding was introduced, and the results of running five stages of tube mills and bowl classifiers were shown. Since 1940, the ball milling end of the plant has been altered extensively as a result of tests on the use of 3-in. rods in 7x6-ft mills and the use of the Tyler repulping screen with from 7 to 14 mesh screens. These tests are lengthy and may be covered in a separate report later. The scope of this report is confined to ore ground by rod milling and ball milling until it passed through an 8 mesh Tyler Ty-rod screen. The —8 mesh screen undersize then was pumped to a primary bowl classifier in open circuit and the sands from the bowl sent to the primary pebble mills, see Fig. 1. In the pebble mill circuit the ore is ground to 90 pct —325 mesh (24 pct + 28 microns). In studying the flowsheet, attention should be paid to the efficiency of the classification equipment used. The Tyler repulping screen is an efficient machine on the 8 to 10 mesh separation, and the bowl classifier is equally efficient at the 325 mesh separation. Efficient classification is a necessity for series-circuit stage grinding. The ore is hard siliceous porphyry, 60 pct SiO,, 80 pct insoluble. Its grindability at different meshes has been shown near the top of the list in F. C. Bond's grindability tests.' Lake Shore is not shown, but an adjacent mine with identical ore, Wright-Hargreaves, is. Reasons for the Changeover Since 1936 grinding balls have been rising steadily in price with no sign of stopping. For a mill that used 4.5 to 5.2 lb of grinding balls for every ton of ore ground this rise represented an alarming increase in grinding costs. In many cases the quality of the grinding balls fell off as the scrap steel became more difficult to obtain. The ratio of tube mills to ball mills increased with the use of the Tyler repulping screen in the ball mill circuit. Originally only 3.0 lb of balls per ton were used in the tube mills, and this

Jan 1, 1953

?ADAIR, ARTHUR C., Corp 4th Co., 1st. Training Bat., 154th Depot Brigade. ADAMS, HENRY, Major: Chemical Warfare Service. ARLUCK, A. A Headquarters, 1st Corps of Artillery. ASKIN, THOMAS B. H Ensign. BANKS, H. R., 2d Lieut Canadian Engineers. BAYLESS, G. E. S Supply Dept. U. S. Submarine Base. BELL, L. R Co. C, 302d Engineers. BELLIS, ARTHUR E., Capt Ordnance Reserve Corps. I BIRRETT, HOWARD, Lieut., Aviation Section, U. S. Signal Corps, Ellington Field. BOISE, PAUL T 2d Regiment, 24th Squadron. ?BRADLEY, CLARENCE I Convois Automobile Section 585. BROWN, GEORGE M Co. G lot Engineer Replacement Regiment. BUCKINGHAM, ALBERT U. S. S. " Coronet," S. P. 194, Section Base No. 7. BURNS J. J Co. 1-B, E. R. O. T. C. BURT, Co. B, let Engineers Replacement Regiment. ||BYERS, WHEATON B., 2d Lieut Ordnance Dept. CANTON, WILLIAM R., Sgt Headquarters Co., 80th F. A. CARSON, JOSEPH A., Capt A.S. S. R. C.' CHAPMAN, LEWIS C. Corp 29th engineers. CHETNEY, P. C., 2d Lieut 15th Bat. Headquarters Co. CHEVRILLON Louis French Red Cross. CHIDESTER, W. B., 1st Lieut 24th Machine Gun Bat. CHURCH, JOHN L., Capt 308th Engineers. CLAGHORN, D. MONTGOMERY, 1st Lieut 45th Engineers. CLAQHORN, JAMES L., Lieut Aviation Section, Signal Corps. CLARKE, ALEXANDER F U. S. Naval Aviation Service. COMINS, WALDO H. Ca t 41st Co., 164th Depot Brigade. COOK, FREDERICK A., Capt., Engineer Reserve Corps, Asst. to Div. Engr. 79th Division. COOPER, CLAUDE H. Capt C. A. R. C., 50th Artillery. COPELAND, N. R., Lieut. ||CORBY H.. G., 1st Lieut Co. D, 109th Supply Train. CORSA, BEAN, Capt Co. D, 612th Engineers. CORTESE, EMILIO Italian Army. COULDREY PAUL S., Corp British Expeditionary Forces. || CRAGIN, RODNEY S Co. E, 115th Engineers. CURRIE, JOHN M., Ca t Royal Engineers. || CUTTING, G. W., 2d Lieut U. S. Reserves, Field Artillery. V DARRINGTON, PAUL N., 1st Lieut U. S. Infantry. DAVIS, ANGUS W., Lieut-Col British Expeditionary Forces. || DAVIS, THORNTON, 1st Lieut 13th Field Artillery. ELAND, FREDERICK A., Major Engineer Reserve Corps. DOUGLAS, JAMES $ American Red Cross. DOVE, D. R., Candidate 21st Training Battery, F. A. C. O. T. C. Dover JAMES J 6th Co. C. B. DOWS, DAVID,Capt Coast Artillery, Officers Reserve Corps. || DRAKE, M. 6., 2d Lieut Headquarters Co., 325th Infantry. I || EMMERSON, E. Roy British Navy. EVERIT, RICHARD STURTEVANT Heavy Artillery Officers' Training Camp.

Jan 1, 1923

By John A. Fagnant

At Elkol, Wyo., about 80 miles northeast of Ogden, Utah, the Kemmerer Coal Co. and the Utah Power and Light Co. are involved in a joint venture that will soon see 1 million tons of coal going "out by wire" to Ogden. Kemmerer, owner of a multi-seam strip mine, and the utility, now building a steam power plant adjacent to the mine site, expect to begin initial power generation by February 1963. Although capable of producing only 150,000 kw at that time, this plant is expected to be ultimately enlarged to 500,000-kw capacity which will require about 2 million tons of coal annually. The deposit consists of more than 30 seams of coal, usually varying in thickness from 2 to 40 ft, and separated by beds of sandstones and shales. In certain areas the aggregate thickness of all the coal seams measures 300 ft. The thickest and most spectacular of these seams is the lowest one, referred to as the No. 1 seam, which is 118 ft thick in some places.

Jan 8, 1962

By S. S. Rumsey

Introduction IN order to realize the economies which would result in operating the mine pumps at the Chapin mine with electricity. generated by water power, the Oliver Iron Mining Co. recently installed a hydro-electric plant at the upper Quinnesee, falls on the Menominee river, and constructed a transmission line to the mine. On account of the large flow of water in the Chapin mine, and the great depth from which it has to be handled, it was necessary to make a thorough investigation of the merits of both the motor-driven centrifugal and motor-driven plunger pumps, in order that the most economical results as regards power, cost of installation, maintenance, and operation, be obtained. This investigation resulted in the selection of motor-driven centrifugal pumps, as the cost of the pumps and motors, installation, and maintenance was considerably lower, and the space required in the underground workings very much smaller, than for the plunger pumps. The overall efficiencies guaranteed by several of the centrifugal-pump manufacturers were so nearly those guaranteed by plunger-pump manufacturers that the saving in power which would result from the installation of plunger pumps did not justify their increased first cost and the increased cost of installation under the conditions prevailing at the Chapin nine. In order to substantiate the representations of the centrifugal-pump builders it was deemed necessary to insist upon a factory test of the completed units before shipment, the test to be conducted under conditions of head and capacity approximating as nearly as possible those under which the pumps would operate in service. Furthermore, it was considered necessary to demonstrate, by test, that there were no deficiencies in design or capacity of the pumps or motors before their final installation in the mine, as it would be extremely difficult to make alterations in the pumps or motors after they were installed.

Jan 10, 1914

By Thomas T., Read

IN this survey of the progressive development (of education for the mineral industries throughout the United States, the review of .the history of each school has usually been completed wherever it is first mentioned, but the history of the schools in the cities of the eastern seaboard was not carried beyond 1870. It is necessary now to cover what happened during the period of approximately the last quarter of the nineteenth century in several of the schools in the east. Philadelphia Of Philadelphia, it has been related in chapter 4 that the Polytechnic College of Pennsylvania began offering a curriculum leading to the B.S. in mining in 1853; that the school did not prosper, and finally closed about 1890. The establishment of a Department of Mining, Arts, and Manufactures at the University of Pennsylvania in 1855-56 was also mentioned, but its history was not carried beyond 1860. In 1859 J. Peter Lesley was appointed professor of mining in the University of Pennsylvania. The son of a cabinetmaker, born in Philadelphia Sept. 17, 1819, he had taken his A.B. degree at the University of Pennsylvania in 1838 and then secured a position on the Geological Survey of Pennsylvania under H. D. Rogers. When the Survey was discontinued, in 1841, he went to Princeton to study theology, was ordained a Presbyterian minister and followed that career until 1852, when the Pennsylvania, Geological Survey was again started and he rejoined its staff. He published "A Manual of Coal and its Topography" in 1856, and studied at the École des Mines, Paris, in 1856-57. He published an 800-page "Iron Manufactures Guide" the year that he was appointed to the staff at the University of Pennsylvania. In 1863-64 a College of Agriculture, Mines, Arts and the Mechanic Arts was established, but it was not a separate school

Jan 1, 1941