Search Documents

By L. R. Weisberg, E. A. Miller

Single-crystalline films of silicon of good quality were vacuum-deposited on sapphire. The improved crystallinity was achieved by the strict exclusion of oxygen from the evaporation system, including the use of a "oxygen-free" silicon source. To minimize possible contamination of the source, the silicon was sublimed from the solid at about 1390° C. using a simple electron bombardment system to heat the silicon. This resulted in deposition rates of about 5 to 7 µ per hr and film thicknesses of 4 to 20 µ. The vacuum during deposition was ordinarily about 5x 10-8 Torr, DESPITE the success achieved in the chemical vapor deposition of silicon on sapphire using Silane,1-4 vacuum deposition has not provided comparable properties. For example, Chu et a1.5 vacuum-deposited silicon on single-crystalline substrates of A12O3, Sic, ThO2, and other compounds, and, although some epi- but the use of ultrahigh vacuum (about 1 to 3 x10-9 Torr) during deposition did not significantly improve the results in the oxygen-free system. The crystalline quality of films deposited on (0001) sapphire was found to be considerably superior to (1102) sapphire surfaces. Using (0001) sapphire, single-crystalline films were deposited at temperatures as low as 780° C and as high as 1075°C, with the best crystalline quality obtained at about 1000°C. At this temperature, hole mobilities over 250 sq cm per v-sec were achieved. taxy was indicated, single-crystalline films were not produced. More recently, Salama, Tucker, and young6 evaporated silicon on single-crystalline sapphire, but only poor crystallinity was observed, and low carrier mobilities were measured. In the present experiments, good-quality single-crystalline films of silicon on sapphire have been achieved by specifically excluding oxygen from the evaporation. This included not only the use of a "clean" vacuum system but, of special importance, the use of an oxygen-free silicon source. This has also been shown to provide a dramatic improvement in silicon homoepi-taxy.7 As a result, silicon-on-sapphire films with hole mobilities over 250 sq cm per v-set were achieved, and single-crystal films were grown as low as 780°C and as

Jan 1, 1969

By Herbert R. Hanley

THE One Hundred and Twenty-sixth meeting-of the Institute, held in San Francisco, Sept. 25 to 29, 1922, was a success in every way. Character-istically, San Francisco presented climate suited, to the occasion, while the Committees on Arrangements left nothing undone that would contribute to the interest and entertainment of the members and their wives. There was a registration of over 230, and all sections, save three, were represented. In the technical meetings, under the leadership of Albert Burch in the mining session and C. W. Merrill in the milling session, the greatest interest was manifested in ore-hunting geology and modern ore-dressing methods. The general geologic phase developed numerous discussions and had for its aim the study and correlation of known data and the application-of these to the finding of commercial orebodies. The geologic features of the Comstock and their significance to the development of the present orebodies were discussed. This brought out matters of much technical interest as well as those of romantic nature in the history of the early life of that camp. The profitable application of modern milling methods to ores, non-commercial a short time ago, was discussed with much interest. The recent work on the Comstock ores occupied a conspicuous part in these discussions. Basic principles delineated by mathematical study of mechanical devices for the milling of ore came in for a prominent part in the program as well as the physical-chemical side of the processes devised for the winning of precious metals as a profit.

Jan 11, 1922

By Louis R. Hodell

WHEN the drilling of an oil well is completed a permanent opening from the reservoir to the surface must be provided. This is done by lining the hole with pipe, commonly known as casing. In the past, all but a small amount of casing has been run in the hole and joined by threads and couplings. Recently, however, in California, Texas, and Oklahoma, there has been a definite tendency 'to adopt -the welded joint for the following reasons: (1) Plain end casing for welding may be bought for 15 per cent less than thread-and-coupled casing; some of this is offset by the cost of welding the pipe in the hole but a respectable net profit remains.

Jan 1, 1937

By J. S. Fulton

Those who live in steel-mill towns are so accustomed to the sight of flames spouting from the mouth of a Bessemer vessel that they seldom pause to think of the amazing process behind it. Actually cold air is being blown through a hot liquid and, instead of cooling it, raises the temperature of the liquid. When coffee is too hot to drink, we know that blowing on it will cool it, so it was no wonder that when Henry Bessemer (or William Kelly, as your patriotism chooses) first proposed this cycle of steel production, he was considered mad. When Bessemer and Kelly started their investigations around 1852, there was not much practical knowledge of metallurgy and, in consequence, there was wide variation in the product made by their process. It was appreciated that the silicon, carbon and iron were all potential fuels, but not until Mushet discovered the beneficial effects of having manganese in the pig iron did the process really become commercial. Bessemer's patent of 1855 covered a crucibleful of liquid iron into which a refractory tuyere was lowered and the blow started. Since that time virtually every conceivable form of vessel, bottom arrangemerit, tuyere size and location have been suggested or tried. There have been stationary vessels with fixed bottoms, that were side, top or bottom blown; tilting vessels with two sets of side tuyeres at different elevations; vessels like a three-compartmerit septic tank; vessels of a cylindrical form supported on the long axis with tuyeres along the side submerged by a partial rotation of the vessel (this type continues in copper refineries); portable vessels to make the blow in a ladle over a mold in a foundry; a combination of a cupola and converter in one shell, and various other arrangements. But in all these experiments, compressed air for the blast was presupposed and there was little discussion of the quantity or quality of the air delivered to the tuyeres. At one time or another various practices that now are forgotten have been tried or suggested: for instance, the use of inert gas at the end of the blow; the addition of fuel to the blast; the use of hot-blast stoves; the drying of the air to a minimum moisture in the blast. Except in the last-named method little attention was paid to the quality or quantity of the air blown. Phases Of the many Papers published On various phases of the Bessemer process, nearly '7' according to one bibliography, Over go per 'ent were concerned with the metallurgical phase and less than '0 per cent discussed various sections of the pneumatic phase. Since the two phases are coincidental, apparently nine times as much thought has been given to the result as has been given to One of the causes of the Bessemer process. IS it not possible that if more attention had been paid to the pneumatics so many papers would not have had to be written on the troubles in the metallurgical phase? A study of published papers and conversation

Jan 1, 1941

By J. S. Fulton

Those who live in steel-mill towns are so accustomed to the sight of flames spouting from the mouth of a Bessemer vessel that they seldom pause to think of the amazing process behind it. Actually cold air is being blown through a hot liquid and, instead of cooling it, raises the temperature of the liquid. When coffee is too hot to drink, we know that blowing on it will cool it, so it was no wonder that when Henry Bessemer (or William Kelly, as your patriotism chooses) first proposed this cycle of steel production, he was considered mad. When Bessemer and Kelly started their investigations around 1852, there was not much practical knowledge of metallurgy and, in consequence, there was wide variation in the product made by their process. It was appreciated that the silicon, carbon and iron were all potential fuels, but not until Mushet discovered the beneficial effects of having manganese in the pig iron did the process really become commercial. Bessemer's patent of 1855 covered a crucibleful of liquid iron into which a refractory tuyere was lowered and the blow started. Since that time virtually every conceivable form of vessel, bottom arrangemerit, tuyere size and location have been suggested or tried. There have been stationary vessels with fixed bottoms, that were side, top or bottom blown; tilting vessels with two sets of side tuyeres at different elevations; vessels like a three-compartmerit septic tank; vessels of a cylindrical form supported on the long axis with tuyeres along the side submerged by a partial rotation of the vessel (this type continues in copper refineries); portable vessels to make the blow in a ladle over a mold in a foundry; a combination of a cupola and converter in one shell, and various other arrangements. But in all these experiments, compressed air for the blast was presupposed and there was little discussion of the quantity or quality of the air delivered to the tuyeres. At one time or another various practices that now are forgotten have been tried or suggested: for instance, the use of inert gas at the end of the blow; the addition of fuel to the blast; the use of hot-blast stoves; the drying of the air to a minimum moisture in the blast. Except in the last-named method little attention was paid to the quality or quantity of the air blown. Phases Of the many Papers published On various phases of the Bessemer process, nearly '7' according to one bibliography, Over go per 'ent were concerned with the metallurgical phase and less than '0 per cent discussed various sections of the pneumatic phase. Since the two phases are coincidental, apparently nine times as much thought has been given to the result as has been given to One of the causes of the Bessemer process. IS it not possible that if more attention had been paid to the pneumatics so many papers would not have had to be written on the troubles in the metallurgical phase? A study of published papers and conversation

Jan 1, 1941

Jan 1, 1967

By C. Perez-Rosales

A simplified method for evaluating specific surface of porous media is described. The theory takes as its point of departure a previous statistical method. Due to its simplicity, it is considered that the proposed method has certain advantages over methods currently used. By making some simplifications, the procedure for estimating specific surface is reduced to superposing, on an enlarged reproduction of a section of the sample to be analyzed, an evenly spaced grid and counting the number of intersections of the grid lines with the perimeter of pores. An indirect test of the theory is presented and the advantages of the method are discussed. INTRODUCTION The specific surface of a porous medium, defined as the surface area of the pores per unit bulk volume, is an important parameter with regard to flow of fluids through porous materials. In particular, it has long been recognized that specific surface is closely related to permeability. Since the internal surface of any porous material is extremely complex, the measurement of specific surface can only be accomplished by indirect means. It is considered that the best method' in current use for determining specific surface is the statistical method of Chalkley, Cornfield and Parka who originally applied it for estimating volume-surface ratios of morphologic components, such as cells or nuclei. This method will be outlined later. A method which has been used extensively in determining specific surface is based on the adsorption of a vapor by the internal surface of porous media. However, this method does not yield the surface pertinent to fluid flow, since it includes the tiny molecular interstices which do not influence the permeability of the porous material.' This method has been employed by Brooks and Purcell measure internal surface area of sedimentary rocks. The Kozeny equation, which relates the specific surface to the permeability of a porous medium, has found wide use in determination of specific surface. However, the KOzeny equation is not strictly correct. Large discrepancies have been found between theory and experiments.' Consequently. the specific surface estimated by this method is subject to serious uncertainties. Finally, there are other methods for specific surface measurements which are based upon a variety of physical and chemical properties: the heat conduction by a gas, ionic adsorption phenomena and direct chemical reactions of the surface with other substances. This paper describes a simplified statistical method for determining specific surface of porous materials. It is considered that, due to its simplicity, it has certain advantages over the methods presently used. For its validity, it is required that the porous structure of the material under study be of a spatially random nature. This is not a serious limitation since the naturally occurring porous media have this characteristic. THEORY The method proposed in this paper takes as its point of departure the interesting result obtained by Chalkley et al The method shows that if a line of length r is dropped repeatedly at random over a section of a porous medium, and counts are made of the number of times the two end points fall within pore areas (denoted by h for "hits") and the number of times the line intersects the perimeter of pores (denoted by c for "cuts"), then in a very large number of throws where S is the internal surface of the sample (surface of pores) and V, the volume of the pores (Fig. 1). Since the specific surface S, and the porosity 4 are given, respectively, by S. = Sl V, and 4 = V,l V,, where V, is the total volume of the sample, it follows from Eq. 1

By J. A. Bownocker

THE production of oil in Ohio, in 1924, was characterized by no marked or surprising change. Low prices and the absence of promising territory made the year quiet. As is well. known, Ohio has reached a state of "settled production," and the most that can be expected for the ensuing few years is to maintain the output at approximately the present figure 1921 7,335,000 1922 6,781,000 1923 7,085,000 Geographically, the Ohio fields may be divided into three areas, each of which gets its main supply of oil from a different stratigraphic horizon.

Jan 3, 1925

By Harlowe Hardinge

THE sound made by ball, pebble and rod mills has long been used by the operator as the "telltale" of their operation. The nature of this sound depends upon local conditions and the type of mill used. By experience an operator can tell whether the mill is running properly or not. Some operators are able to detect the difference in sound much better than others and get better results running the same mill tinder the same conditions. The automatic operation of a mill using sound as the fundamental means for maintaining control presents many problems. The satisfactory solution of these problems requires, for given operating conditions, a greater average output, with improved product for subsequent processing, than can be obtained by manual control.

Jan 1, 1939

By George Steintveit

Det Norske Zinkicompani A/S was established in 1924, on the initiative of the Compagnie Royale Asturienne des Mines. Experimental electrothermic zinc production was carried out on industrial scale for a two-year period, but the problems of electrothermic smelting were not solved. A license for the electrolytic zinc production process was then obtained from the Anaconda Copper Mining Co. A plant for electrolytic zinc production was built, near the small fjord town of Odda in Hardanger, West Norway, The production was based on zinc ore from Spain, and cheap local hydro-electric power. The plant came into operation in 1929. Annual capacity, 36,000 tons. In 1964 a long-term agreement was concluded with Boliden AB by which Det Norske Zinkkompani is secured the raw materials basis for an expansion of the annual capacity to 100,000 tons of zinc, Since World War II, the company has been pursuing extensive research and development programs. As a result, various sections have been rebuilt: nev unloading and storage facilities, a 250 ton per day Fluid Bed Roaster with contact plant, new continuous leaching system, integrating the Jarosite Residue Process, new solution purification section - upgrading the solution quality for a 600 Amp/m2 current density Tank Room operation -, installation of induction furnaces for cathode melting with casting machines and automatic stacking of slabs. Simultaneously, instrumentation, and methods of automatic control have been developed and introduced, providing conditions for optimal plant operations.

Jan 1, 1970

By E. H. Hamilton

WHEN starting a series of experiments on the use of powdered coal in lead blast furnaces to replace coke, I realized that in copper smelting the problem is simpler because the sulfur recovers the copper in the form of matte. In lead smelting there are greater difficulties because a reducing atmosphere must be maintained in the active, zone corresponding to each tuyere in order to get the best recovery of lead. Therefore, the feed of powdered coal must be quite regular, uniform and under control. The molten products issuing from the taphole are the resultant of the work of all the tuyeres and it can readily be con-ceived that one part of the furnace may be forming slag with a higher lead content than the slag formed in other parts of the furnace. At first, we used only one tuyere situated on the back of the furnace. This was for the purpose of getting all of our regulations under the regular operating conditions. We tried every known system of feed and found they were not dependable and our present system was finally worked out, and so far as we know, is the only working system that will give uniformly good saving in lead blast furnaces. We placed a Bristol self-recording thermometer on the feed floor. This gives a 24-hr. continuous record of the temperature of the gases leaving the furnace. We put a self-recording gage on the "15-lb." air used in the injector. A second recording Bristol gage was put on the low-pressure air (40 oz.). I realized that it was necessary that we should know the exact weight of coal going into each tuyere and that it should 'be under observation at all times. L. W. Kirk was assigned to the problem and developed the open sight feed and the distributor, so that we now have the coal being fed into each tuyere in sight of the men in charge. We have an apothecary's balance beside the furnace, and the operator takes the pan and inserts it under the stream of falling powdered coal for one minute, and places the pan on the scale, the other scale pan having weights indicating the desired amount to be fed to each tuyere per minute.

Jan 10, 1922

Jan 1, 1966

By L. H. Levenson, Charles S. Barrett

Plastic flow in metal crystals and the changes in orientation resulting from it are generally understood to take place by the following fundamental mechanisms: (1) slip on crystallographic planes, (2) homogeneous crystal rotation resulting from the slip, (3) bending of the 1attice between the planes of slip, and, under certain circumstances, (4) twinning. This paper and a preceding one on iron subjected to uniaxial compression1 concern two additional processes that must now be added to this list: (5) the formation of deformation bands, and (6) the bending and rotation of these bands. The present investigation yields a new understanding and definiteness to the common terms so loosely used when speaking of cold-worked metals —('grain fragmentation," "elongated grains," and "deformation twins," "deformation bands," "etch bands," or "X-bands." Bands have been noted on the polished and etched surfaces of cold-worked metals by various investigators for more than 25 years, ‡ yet their nature and their significance have been so little understood that they are not treated in the most comprehensive modern texts on the deformation of crystals. The experiments in this series show that they are one of the fundamental processes in the deformation of metals, of importance in the development of preferred orientations, in work-hardening (since they have the effect of reducing the effective grain size and interfering with slip), and in the recrystallization process. The present experiments were performed on the same stock of material that was used in the earlier compression experiments1—hydrogen-purified mild steel in which the carbon content had been reduced to the limit detectable under the microscope and in which single crystals could be grown by a strain-anneal treatment.2

Jan 1, 1939

By Charles S. Barrett, L. H. Levenson

Plastic flow in metal crystals and the changes in orientation resulting from it are generally understood to take place by the following fundamental mechanisms: (1) slip on crystallographic planes, (2) homogeneous crystal rotation resulting from the slip, (3) bending of the 1attice between the planes of slip, and, under certain circumstances, (4) twinning. This paper and a preceding one on iron subjected to uniaxial compression1 concern two additional processes that must now be added to this list: (5) the formation of deformation bands, and (6) the bending and rotation of these bands. The present investigation yields a new understanding and definiteness to the common terms so loosely used when speaking of cold-worked metals —('grain fragmentation," "elongated grains," and "deformation twins," "deformation bands," "etch bands," or "X-bands." Bands have been noted on the polished and etched surfaces of cold-worked metals by various investigators for more than 25 years, ‡ yet their nature and their significance have been so little understood that they are not treated in the most comprehensive modern texts on the deformation of crystals. The experiments in this series show that they are one of the fundamental processes in the deformation of metals, of importance in the development of preferred orientations, in work-hardening (since they have the effect of reducing the effective grain size and interfering with slip), and in the recrystallization process. The present experiments were performed on the same stock of material that was used in the earlier compression experiments1—hydrogen-purified mild steel in which the carbon content had been reduced to the limit detectable under the microscope and in which single crystals could be grown by a strain-anneal treatment.2

Jan 1, 1939

By George T. Wickes

(Washington Meeting, May, 1905.) SEVERAL years ago, Mr. Robert A. Cook described and illustrated in our Transactions 1 a mechanical coke-drawer, patented in 1891 by Mr. Thomas Smith of the Thorncliff Iron Works, Sheffield, England, and first introduced in the United States in, 1896, at the coking-plant of the Latrobe Coal Co., Latrobe, Pa. This machine has not received any very extended application in this country, although it was successfully used in two places for a number of years. The present. paper describes a new and simpler machine, containing few wearing-parts capable of withstanding continued rough usage. Anything which tends to prolong the general use of bee-hive ovens will be welcome to those who are interested in cheapen¬ing the cost of producing coke in such ovens, especially if it provides satisfactory mechanical means, replacing the hard labor involved in drawing coke by hand with the old-fashioned ?duck bill.? The difficulty of finding efficient coke-drawers, especially during the summer season, and in the South, is notorious. Yet, notwithstanding the great improvements that have been made in retort coke-ovens, new bee-hive ovens are continually constructed; and a machine which will successfully compete with hand-drawing, and, at the same time, add to the efficiency of the bee-hive oven, seems to deserve notice. The machine here described was put in operation at the Frick Coal and Coke Co.'s plant, known as Continental No. 1, at Uniontown, Pa., in October, 1904, and is reported to have met successfully all the tests to which it has been subjected. This trial has demonstrated that one of these machines, equipped with an electric motor, and operated by one mart with an assistant, besides two men to " water down " the

Jul 1, 1905

By Elmer W. Pehrson

THE founding of the American Institute of Mining Engineers in 1871 came at an unusually significant moment in the life of our country. The industrial revolution, in which mineral production played a major role, was just getting underway. The iron industry, established several decades earlier, was reaching sizable proportions. In 1871 pig-iron production was approaching 2 million tons, and the industry had spread as far west as Missouri and Wisconsin. The chief sources of iron ore were Pennsylvania, New Jersey, New York, and Michigan. The age of steel was in its infancy; production had not yet reached 100,000 tons per annum. The gold rush to California two decades earlier and the discovery of other gold and silver bonanzas in the West paved the way for the transcontinental railways, which were then being built and which contributed much to the subsequent development of the great copper, lead, and zinc districts of the Rocky Mountain area. Regular production of copper in the Michigan peninsula and of lead in Missouri and the upper Mississippi region had been established for many years but on a scale dwarfed by the quantities later required as technical progress, invention and enterprise made possible the rapid expansion of industry. Discovery of oil in Pennsylvania in 1859, the growing recognition of the

Jan 1, 1947

By Byron Johnston

IN 1926 I had occasion to make numerous measure-ments with a Pitot tube. The differential gage was mounted in a box, and since the work entailed setting upon girders, staging, and flues of various shapes and slopes, much time was generally expended in getting the box blocked into the level position. This inconvenience was so considerable that I devised the gage stand shown in the accompanying illustration. The gage is bolted to the board seat, the bolt per-mitting unlimited adjustment in the plane of the paper. The seat, carrying the gage, revolves on trunnions, per-mitting unlimited adjustment in a second plane, per-pendicular to the first. Consequently, the stand may be stood up, hung by one corner, leaned against some-thing or simply laid down, and the gage levelled from any position. On uneven surfaces, where the stand naturally rests on only three of its legs, it may be swung in the manner peculiar to the tripod, bringing the center of gravity within the triangle formed by the legs, thereby providing a firm set-up. Rubber stoppers under compression were found to give sufficient friction to hold the seat in the desired position.

Jan 3, 1928