Search Documents

By Ralph M. Hunter

UNTIL recent years, maintenance of surface coal handling facilities was a relatively simple task. Equipment consisted principally of conveyors, screens and crushers of comparatively simple construction. Electrical equipment consisted of motors and starters, with little, if any, interlocking. In most cases failure of any component affected only the grades of coal loaded so that even a prolonged break-down did not affect mine operation materially. However, with the introduction of modern cleaning plants, the picture has changed. The equipment is much more complex and therefore more difficult to maintain. In many cases failure of any component of the plant prevents loading of coal. Even if provision is made to by-pass, the quality of coal loaded is lowered, affecting markets. In the case of plants designed to permit full seam mining, marketable coal cannot be loaded without operation of the cleaning plant. Under these conditions it is apparent that considerable thought and effort toward better maintenance are justified. In order to assure continuous, efficient and economical operation, maintenance should receive consideration, not only after the plant is in operation, but while it is being designed. It is hardly necessary to say that the designer should strive for sturdiness and wearing qualities. It is sometimes not realized, however, that even the best parts will sooner or later require replacement or repair. The designer should, therefore, give consideration to accessibility. Anyone who has had to do with cleaning plant maintenance is familiar with installations where several hours are required to get at a part that can be repaired or replaced in a few minutes, once it is accessible. As in most cases, experience is the best guide. The men who operate and maintain this equipment know the problems encountered. Whenever available, the opinions of these men should be sought and heeded. As an example, we might consider the refuse elevator on a Chance Cone. Our company is now operating three of these cones, the first of which was installed in 1941, and the latest in 2946. Exact records are not available, but well over 50 pct of delays charged to the Chance Cones have been caused by the refuse elevator. This elevator receives refuse from the cone and carries it to a point above the water level of the cone, discharging onto a dewatering and desanding screen. Since the elevator operates under water and necessarily has close clearances in the lower boot, it tends to jam on large pieces of refuse or tramp iron. The chain, buckets and boot are also subjected to the action of water, sand and refuse, which accelerate normal wear. In case of jamming or chain-breakage it is necessary to drain the elevator and the cone so that even a minor fault in the elevator causes a considerable loss of time for the cone. In our new plant, which will contain two Chance Cones, the refuse elevator has been eliminated. This was accomplished by raising the cone so that the refuse gates could discharge directly onto the dewater-

Jan 1, 1948

By Frank Kneeland

SAFETY FIRST is a popular motto-most mining companies have adopted it. It is probable, however, that in the majority of cases it is only a motto and gets no further than the office stationery or the bulletin board at the mine's entrance. In but few industries is there employed a greater diversity of machinery and mechanical devices than in coal mining. The list ranges all the way from mechanical stokers to wood-working machinery and undercutters. Many of these devices, particularly those employed in wood working, are extremely dangerous. In 1913, 23 per cent. of all fatalities occurring in coal mining in the U. S. were caused by machinery of some sort or other. Although the forms of accidents occurring with mining machinery are legion, they generally arise from one or more of five causes: (a) Falls from ladders, platforms, etc.; (b) coming in contact with moving machines or parts thereof; (c) electric shocks; (d) failure of some machine part; (e) mismanipulation of valves, levers, switches or other hand-operated controlling devices. The steps which may be taken to prevent accidents from the above causes are almost as numerous as the accidents themselves. There is, and can be, no panacea for all mishaps, nor for any one class of accidents. There is no mathematical or other formula that will bring immunity under any set of conditions. Common sense is the only guide. The remedy for the first-named class of accidents is simple and generally effective-namely, make the staging, ladder, platform, or other support, abundantly strong to carry any possible weight that it may be called upon to bear; provide ample railings on platforms or runways, and non-slipping feet on movable ladders.

Jan 1, 1915

Texture Transition in Ordered CuAu, by E. A. Starke, Jr., J. C. Ogle, and C. J. Sparks, Jr., Trans. TMS-AIME, 1969, vol. 245, pp. 169-70. pole figures should have had two parts not one. On the Estimation of Oxygen Absorption by Continuous Molten Metal Streams, by J. Szekely, Trans. TMS-AIME, 1969, vol. 245, pp. 341-44.

Jan 1, 1970

By William E. Ford, Edward Salisbury Dana

The Silicates are m part strictly anhydrous, in part hydrous, as the zeolites and the amorphous clays, etc. Furthermore, a large number of the silicates yield more or less water upon ignition, and in many cases it is known that they are, therefore, to be regarded as basic (or acid) silicates. The line, however, between the strictly anhydrous and hydrous silicates cannot be sharply drawn, since with many species which yield water upon ignition the part played by the elements forming the water is as yet uncertain. Furthermore, in the cases of several groups, the strict arrangement must be deviated from, since the relation of the species is best exhibited by introducing the related hydrous species immediately after the others. This chapter closes with a section including the Titanates, Silico-titanates, Titano-niobates, etc., which connect the Silicates with the Niobates and Tantalates. Some Titanates have already been included among the Oxides.

Jan 1, 1922

By Gregory L. Gullord

In September, 1975, production was begun at the new milling facility of ASARCO Incorporated, the Young Mill. The mill is located adjacent to the Young Mine 35 km (22 miles) east of Knoxville, Tennessee. The Young Mill replaced the obsolete Mascot Mill which had been operating since 1913. The basic flow sheet of Mascot was retained for the construction of the Young Mill, with a 20% increase in capacity included in the design. The Young Mill is capable of processing 7710 - t/d (8500 stpd) of crude ore from three underground mines (Young, Immel and Coy) yielding 300 - t/d (330 stpd) of 63% zinc concentrate. The Young Mill is unique in that 92.5% of the ore milled is recovered as saleable products, including zinc concentrate, construction aggregate, sand and agricultural limestone. Processing at the Young Mill is divided into five basic stages: two-stage crushing, heavy media separation, grinding-flotation, concentrate filtering and drying, and limestone by-products recovery. The ore bodies are located in the Knox formation, which consists of primary dolomite, secondary dolomite and limestone with silicas in the form of chert and jasperoid. The zinc mineralization occurs as an exceptionally pure sphalerite. The ore contains an occasional abundance of pyrite and traces of fluorite and barite. TWO STAGE CRUSHING Ore enters the crushing section from two points. The Young Mine ore is hoisted into a 816 ton (900 st) bin which feeds a 1.52m (60 in) conveyor via a 1.52 m (60 in) vibrating feeder. The Immel ore is trucked 10 km (6 miles) by an independent contractor and weighed on automatic recording truck scales at the entrance to the property.

Jan 1, 1977

By Charles Will Wright

I. INTRODUCTION. THE application of the camera as an adjunct to topographic mapping began practically with its invention, and it has been employed with varying success since that time. With the exception of the camera to be described, the plate-camera has been universally used in this work, thus giving a projection of the area photographed on a flat surface. From such projections or photographs, by the rules of geometry and of perspective, points defining topographic features and seen from at least two camera-stations may be projected upon a ground-plane-the map.1 In 1904 I employed the plate-camera for this purpose in Alaska, but found that the labor necessary to plot the maps, even in a general way, was long and tedious. In 1905 a small Eastman panoramic camera was fitted with spirit-levels, a sightalidade and a transparent scale, introduced inside the camera to register the degree-points in the sky-line of the film-negative; also, arrows to indicate the horizon-line. This was, on the whole, successful; but the details in the topography were not brought out in the views with sufficient clearness, and the photographs were too small. These difficulties were overcome by obtaining a larger and more carefully constructed instrument, which was satisfactorily employed in the field during the year 1906. A panoramic view is made up of an integral number of perspective views upon flat surfaces, and logically is the most ac-

Jan 1, 1908

THE shipments of high-grade manganese ore, con-taining 35 per cent or more of manganese, from the mines in the United States in 1926 were slightly less than half as large as similar shipments in 1925, accord-ing to the United States Bureau of Mines, Department of Commerce. The shipments in 1926 by 45 producers amounted to 46,258 long tons as compared with 98,324 long tons by 42 producers in 1925. This decrease was due to the falling off of the shipments from Montana. The domestic production of metallurgical ore in 1926 was 26,530 tons; that of chemical ore, 19,728 tons. Montana was the largest shipper with 5713 tons of metallurgical ore and 17,904 tons of chemical ore. The largest individual shipper of metallurgical ore was the Crescent Mine in the Olympic Mountain Region, Clallam Co., Washington, from which the shipments for the year were 3162 tons. The mine was operated by lessees and reverted to the owners in July, and thereafter to the close of the year no .ore was shipped.

Jan 6, 1927

By Irving Palmer

DURING the past 15 years in this country there have been few additions to the literature of lead smelting. After the consolidation of the principal smelting companies at the beginning of this period it became the policy of the larger company not to permit the publication of details in regard to many of its metallurgical processes. This led to similar action on the part of some of its competitors. The result, of course, was a decided decrease in the number of papers written upon the practical side of the subject. Even upon the theoretical side the contributions have been few. It would seem that the industry as a whole has suffered from this general unwillingness to exchange information. While it is true that a given company is entitled to the reward that may come from its own development of a new process, it is also true that a still greater reward might be the result of a free exchange of ideas with other plants. This principle has been recognized for a long time in other metallurgical industries, notably those engaged in the smelting of iron and the manufacture of steel. It is pleasing to note that the leading lead-smelting company has very recently decided to modify its policy of secrecy, and to permit the publication of papers covering some details of its metallurgical methods. The statement has been made that there has been but little progress in lead smelting during the period just referred to. This impression is due in part to the scarcity of papers written on the subject. There has been, it is true, some discussion of the new sintering processes, but with little reference to detail, and to the effect that blast roasting has had upon the industry as a whole. In spite of the prevailing belief, it may be said that lead smelting, in common with other metallurgical industries, has made steady and substantial progress. It is the purpose of the present paper to discuss briefly some features of the industry as it is now conducted, with special reference to the blast-furnace practice in the larger silver-lead smelting plants of the United States and Mexico.

Jan 7, 1914

By H. Jehn

Like some other Pt-group metals palladium shows a low but considerable solid solubility of oxygen, which was found already from oxidation studies. The oxygen solid solubility of palladium in equilibrium with gaseous oxygen has been investigated at 900 - 1300 °C in oxygen (665 mbar) and air by gassing and analyzing polycrystalline samples. The 0-concentrations range from 40 to 90 ppm and decrease with rising temperature. The isobaric solubility can be represented by the least-squares fit log c0 = 0.5 log p02- 0.32 + 920/T (c0 in wt. ppm, p02 in mbar, T in K). The thermodynamic data of the exothermic solution reaction are calculated to ?H°= -17.6 kJ?mol-1 and ?S° -76.5 J?mol ? K-1. The behaviour of palladium in an oxygen atmosphere is characterized by the simultaneous reactions of the solution of oxygen in the metal and the formation and evaporation of volatile oxides besides the pure metal evaporation.

Jan 1, 1984

By P. Niessen, W. C. Winegard, C. J. Beingessner

DURING the last 10 years, several grain-growth studies have been made using zone-refined metals with controlled amounts of solute to elucidate the interaction of solute with moving boundaries. In all these studies, it was more or less implicitly assumed that the alloys used were, after recrystallization and grain growth, homogeneous within the grains with respect to solute and lattice defects. This note deals with observations made on microstructures originating from solidification of dilute alloys and from grain growth. Briefly, the experimental procedure used in these studies was the following: zone-refined cadmium and master alloys were melted and cast in Pyrex under vacuum to produce bars 14 mm in diam and about 150 mm long. These bars were cut into 8-mm-thick slices which were mechanically and chemically polished. The specimens were then deformed 30 pct in compression and given a 1-week anneal at 260°C in argon. After this anneal, a second deformation produced completely recrystallized samples 4 mm thick. The time-temperature controlled anneals were carried out in a bath of silicone oil. After the grain-growth anneal, the specimens were polished in Gil-man's' solution (33 g CrOs, 6 g NazSO, in 100 ml of water). Several etches were used depending on the alloy investigated, but mostly a mixture of concentrated HC1 and HNOj (98:2 vol) was employed. In all the alloys examined, the ease with which substructures could be revealed depended strongly on the crystallographic orientation of the surfaces of the grains. However, very frequently the microstructures to be discussed here etched up over broad areas comprising several grains. Fig. 1 is a micrograph of a Cd-0.05 at. pct Mg alloy annealed for 100 sec at 270°C. Different substructures are seen in this photograph. A denotes the now existing grain boundaries. The well-defined lines and points marked B are the remains of a solidification substructure. The lines are boundaries between cell colonies, and the points are nodes located on regular two-dimensional cells. This cellular structure has the same appearance as that found by weinberg2 for rapidly quenched Zn-Au alloys. The "ghost boundaries", marked C, are very similar in appearance to a grain boundary array in a polycrystalline sample. Repeated polishing and etching showed that all the substructures observed were three-dimensional. To date, the ghost boundaries have been clearly observed in all samples containing 0.005, 0.01, 0.05, and 1 at. pct Mg, and in samples containing 0.01 at. pct Zn. Attempts to outline these ghost boundaries in cadmium alloys containing 0.01 at. pct Ag and Au were only partially successful. In these alloys, parallel lines, having a resemblance to the ghost boundaries in the Cd-Mg and Cd-Zn alloys, were observed, but it was not possible to obtain complete arrays of ghost boundaries which extended over several grains. It is possible that a different etch than that presently employed would reveal the ghost boundaries in the Cd-Au and Cd-Ag alloys as clearly as in the Cd-Zn and Cd-Mg alloys. A close examination of the ghost structure showed that it consisted of linear etch-pit arrays, Fig. 2. The ghost boundaries were resolvable even in grains which showed over-all faceting due to the etching, as seen in the corner of Fig. 2. The general appearance of the ghost structure suggests that it originated during grain growth. This is supported by the observation that the mesh width in the ghost-boundary array generally increased with increasing final grain size. To test whether the ghost structure was formed during the long homogenizing anneal or during the grain-growth anneal, some as-cast samples were deformed and given a grain-growth anneal. This anneal was terminated by air cooling or

Jan 1, 1967

By C. G. Wilson

DURING the course of some experiments on the plastic deformation of gallium a standard stereo-graphic projection was prepared with (001) at the center and it was felt that this might be useful to others working with single crystals of gallium. The stereogram, given in Fig. 1, was made using the following crystallographic data (Bradley, 1935):

Jan 1, 1962

Samuel T. Wellman, Cleveland pioneer steel man, who was often referred to as the "father of the open-hearth process of the United States," died suddenly on July 11, 1919, of heart disease, at Stratton, Me. For more than half a century, he was closely identified with the improvement of equipment used in the making of steel and contributed a number of inventions that virtually revolutionized the industry. Mr. Wellman was born Feb. 5, 1847, at Wareham, Mass., his father at the time being superintendent of the Nashua Iron Co., Nashua, N. H. After attending public school and a year at Norwich University, he served in the Civil War as a corporal of the first New Hampshire Heavy Artillery. He went to Pittsburgh in 1867 and assisted in starting the first crucible steel melting furnace built in America at the works of Anderson, Cook & Co. It melted a ton of steel with an average of 1000 Ib. of nut coal, which cost less than $1, while the melting of a ton of steel in crucibles in the old fashioned coke furnace took three tons of the very best coke, costing from $2 to $3 per ton. This furnace was a great success and in a very few years had driven the coke furnace out of use. From Anderson, Cook & Co., Mr. Wellman went to the Singer, Nimick & Co. works, Pittsburgh, where he built two crucible steel melting furnaces of the same type. After that he spent some time in the office of the Siemens agents in Boston and also at steel works in different parts of the country, starting crucible steel furnaces. He then went to the Bay State Iron Works in South Boston, Mass., where he built the first open-hearth furnace that was a commercial success in the United States. It made steel of a much better quality than had previously been made in this country. The principal use to which it was put in those days was the manufacture of locomotive fire-boxes. From South Boston, he went hack to the old works in New Hampshire where his father was still superintendent, and built for it an open-hearth furnace, a plate mill, and a bar mill. In 1873, Mr. Wellman went to Cleveland to design and build the plant of the Otis Steel Co. He remained with this company for 16 years as engineer and superintendent. During this time he developed the open-hearth charging machine and introduced the electromagnet for handling pig iron and scrap steel. The first charging machine was operated by hydraulic power, and although it was not entirely satisfactory it performed the work fairly well and encouraged its inventor to build another one, which was driven by electric motors. This proved

Jan 1, 1920

By AIME AIME

AWRDED jointly by the four AW Founder Engineering Societies the John Fritz Medal is generally regarded as the most signal honor that American engineers can confer on a fellow engineer. The roll of 34 recipients contains the names of Lord Kelvin, George Westinghouse, Alexander Graham Bell, Thomas. A. Edison, George W. Goethals, Guglielmo Marconi, and Michael I. Pupin; and among members of the A.I.M.E. now living, Sir Robert A. Hadfield, Herbert Hoover, and Daniel C. Jackling. On the evening of March 1 7 the name of Paul Dyer Merica was formally added to this list of illustrious engineers when the medal was presented to him at a dinner at the Metropolitan Club in New York. The citation read. For important contributions to the development of alloys for industrial uses. Arrangements for the dinner were made by the following committee representing the four Founder Societies: R. C. Allen, George S. Davison, A. A. Potter, and J. B. Whitehead.

Jan 1, 1938

By RALPH HAYES SWEETSER

ONE per cent. of ash in a ton of coal has been so little considered that in many circles it has been positively ignored. Even P. T. Barnum had never heard of it, or he would have had one on exhibition alongside the Cardiff Giant and the White Elephant. One per cent. of ash is closely related by both those freaks of Barnum in that it is "stone" and, in its aggregate, it is the greatest "White Elephant" that the American public now supports. Some of you may have paid Mr. Barnum for a look at the "petrified man" (named the Cardiff Giant by the gullible wise men of the early seventies); but it is certain that everyone of you is now paying for the support of the great White Elephant that is being constantly carried by our railroads all over the country-at the public's expense. " One per cent. of ash in a ton of coal" requires 120,000 open-top railroad cars each year to transport this use- less stone giant from its native bed in the coal seams of the bituminous regions to the coal bins of the consuming public.

Jan 1, 1924

By W. C. Phalen

The production of salt in the United States divides itself at the outset into two distinct classes…

Jan 1, 1915

By Johnston, T. L.

BISMUTH is found as native metal associated with tin, copper, cobalt, silver, gold, or other metals and in a variety of ores. The more important ones are: bismuthinite (bismuth glance), Bi2S3; bismite (bismuth ochre), Bi2O3.3H2O; and bismutite (bismuth carbonate), Bi2O3CO3?H2O. Of lesser importance are the arsenate, telluride, and vanadate. The sulfide is the most common; the others are often oxidation products from this mineral. Bismuth minerals have been found in various places in the United States, principally in Colorado and Utah, but no ores are mined solely for bismuth. In the Granite mining district of Beaver County, Utah, a stratum of limestone about 6 ft. thick has been almost completely replaced by contact minerals in which bismuthinite associated with pyrite and molybdenite was found intergrown with silicate minerals. In the early days a few small lots of ore assaying 7 to 10 per cent bismuth were shipped from this district. Native bismuth has been found in the Clifton and Tintic districts of Utah. Bismuth is produced as a byproduct in the refining of lead, copper, gold and silver ores, it being recovered from the anode mud from the Betts process. Deposits of bismuth minerals exist in Argentina, Aus¬tralia, China, Japan, Germany, Spain, Peru, Bolivia, and Canada, but Bolivia is the principal, producer and could easily supply all of the present world's demand.

Jan 1, 1933

By JESSE L. MAURY

ONE OF the most hopeful features of the current depression is the discussion which it has en- gendered of ways and means to counteract similar recurrences in the future. 1t is widely recognized that fruitful attack will be directed toward the steady employment of labor, through which the purchasing power of this preponderant class in society will be maintained. S. A, Lewisohn's article' has presented the major factors to be considered; the physical suffering and mental torture endured by those who are deprived of income through no fault of their own, the direct economic losses' sustained in the degradation of 'great, numbers of our population and the disintegration of efficient working forces, and the prime responsibility of owners and managers.

Jan 1, 1931

CONTENTS PAGE Need for Research in Foundry Pig Iron. By Richard Moldenke. (With Discussion) 1 Carbon Characteristics of Copper-bearing Pig Iron. By W. B. Coleman. (With Discussion) 12 A Pig Iron, Low in Total Carbon, is in Demand for Use in Various Industries. By Enrique Touceda. (With Discussion) 24 Carbon in Pig Iron. By Ralph H. Sweetser. (With Discussion) 28 Second Session (Discussion) 37 Need for Research in Foundry Pig Iron BY RICHARD MOLDENKE,* WATCHUNG, N. J. So FAR as the quality of the product is concerned, the history of the production of pig iron for foundry purposes is one of constant retrogression. The steps in this deterioration began with cold-blast charcoal pig iron, then anthracite iron, coke iron; then gradually warm to hot-blast coke iron, with the charcoal furnaces also heating their blast to get greater tonnages, and finally the present-day hot-blast coke irons with scrap additions to the ordinary burden that, according to one European report, have gone as high as 65 per cent. Parallel with this quality retrogression is the enormous increase in furnace tonnages from about 15 to over 1000 tons per day in exceptional instances of modern practice. The key to this situation is economic pressure. The effect is a growing differentiation between furnace production for gray iron and malleable foundries and, for the

Jan 1, 1927

By John M. Kelly

New Mexico produced 31,913,816 bbl. of oil in 1942, the lowest annual production since 1936, and dropped one place to rank eighth among oil-producing states. This production decreased 7,838,052 bbl., or 19.71 per cent, from the 1941 figure is the result of transportation difficulties caused by the dislocation of tanker sailings to east coast ports. The average per-well allowable in New Mexico on Jan. I, 1942, was 43 bbl. and at the end of the year was 38 bbl. Allocations as set by the New Mexico Oil Conservation Commission followed the recommendations of the Petroleum Administrator for War. After setting the daily outlet, however, the average daily pipe-line runs were 87,545 bbl.—11.06 per cent short of these allocations. Production for Lea County was 26,812,949 bbl., Eddy County 4,624,578 bbl., northwestern New Mexico 473,609 bbl., Chaves County 2,680 barrels. Drilling activity for New Mexico in 1942 was approximately 84 per cent of that in 1941 with 339 completions. Of these completions 254 were oil wells, II gas wells, and 74 dry holes. Proven fields accounted for 55 of the dry holes and 19 were wildcats. Three new oil fields and one new gas field were discovered as the result of wildcat drilling. Extensions were made to one oil field and one gas field. By the close of the year, the New Mexico Oil Conservation Commission had designated 59 areas as proven for oil and/or gas. Southeastern New Mexico Lea County Monument was again the largest producing field in the state, with 5,729,336 bbl.; Eunice was next, with 5,217,965; Vacuum produced 3,295,624 and Hobbs 2,973,488. The Hobbs field has the largest accumulated production, which at the close of 1942 totaled 100,381,417 bbl. The 100-million-barrel mark for Hobbs focused attention on the fact that this is the first field in the state to attain this figure, and also that, as Hobbs has been under continuous proration since July 1930, or approximately the entire life of the field, this 100-million-barrel recovery was obtained with 86 per cent of the wells in the pool still flowing and having a drop in bottom-hole pressure of only 3.5 Ib. per million barrels recovered. Hobbs stands out as perhaps the best regulated major oil field in the world. Two new oil fields were discovered in Lca County, the most inlportant being the area designated as East Lusk, consisting of the south 4 tiers of Sections in T. 19 S., R. 32 E. The discovery well was drilled in the SW. SW. 1/4 of sec. 21, T. 19 S., R. 32 E., by Culbertson and Irwin, Inc., and others. It was completed at a total depth of 2751 ft. in the Seven Rivers formation of Permian age. The initial potential of the well was 237 bbl. per day on pump. The oil produced has a gravity of 24.10 A.P.I., with sulphur content of 0.9 per cent. This oil has an asphaltic base and because

Jan 1, 1943

By John M. Kelly

New Mexico produced 31,913,816 bbl. of oil in 1942, the lowest annual production since 1936, and dropped one place to rank eighth among oil-producing states. This production decreased 7,838,052 bbl., or 19.71 per cent, from the 1941 figure is the result of transportation difficulties caused by the dislocation of tanker sailings to east coast ports. The average per-well allowable in New Mexico on Jan. I, 1942, was 43 bbl. and at the end of the year was 38 bbl. Allocations as set by the New Mexico Oil Conservation Commission followed the recommendations of the Petroleum Administrator for War. After setting the daily outlet, however, the average daily pipe-line runs were 87,545 bbl.—11.06 per cent short of these allocations. Production for Lea County was 26,812,949 bbl., Eddy County 4,624,578 bbl., northwestern New Mexico 473,609 bbl., Chaves County 2,680 barrels. Drilling activity for New Mexico in 1942 was approximately 84 per cent of that in 1941 with 339 completions. Of these completions 254 were oil wells, II gas wells, and 74 dry holes. Proven fields accounted for 55 of the dry holes and 19 were wildcats. Three new oil fields and one new gas field were discovered as the result of wildcat drilling. Extensions were made to one oil field and one gas field. By the close of the year, the New Mexico Oil Conservation Commission had designated 59 areas as proven for oil and/or gas. Southeastern New Mexico Lea County Monument was again the largest producing field in the state, with 5,729,336 bbl.; Eunice was next, with 5,217,965; Vacuum produced 3,295,624 and Hobbs 2,973,488. The Hobbs field has the largest accumulated production, which at the close of 1942 totaled 100,381,417 bbl. The 100-million-barrel mark for Hobbs focused attention on the fact that this is the first field in the state to attain this figure, and also that, as Hobbs has been under continuous proration since July 1930, or approximately the entire life of the field, this 100-million-barrel recovery was obtained with 86 per cent of the wells in the pool still flowing and having a drop in bottom-hole pressure of only 3.5 Ib. per million barrels recovered. Hobbs stands out as perhaps the best regulated major oil field in the world. Two new oil fields were discovered in Lca County, the most inlportant being the area designated as East Lusk, consisting of the south 4 tiers of Sections in T. 19 S., R. 32 E. The discovery well was drilled in the SW. SW. 1/4 of sec. 21, T. 19 S., R. 32 E., by Culbertson and Irwin, Inc., and others. It was completed at a total depth of 2751 ft. in the Seven Rivers formation of Permian age. The initial potential of the well was 237 bbl. per day on pump. The oil produced has a gravity of 24.10 A.P.I., with sulphur content of 0.9 per cent. This oil has an asphaltic base and because

Jan 1, 1943