Search Documents

By W. L. Cornell

The Missouri lead ores are the only domestic sources of cobalt presently being mined and processed for other materials. They represent the best short-term solution for meeting up to 13 pct of the Nation's strategic and critical cobalt needs from domestic sources. Presently, the cobalt is lost as an impurity in the copper, lead, and zinc concentrates and in the mill tailings because the technology to recover it with minium impact on present production does not exist. This paper presents results of research, built upon earlier Bureau of Mines laboratory research, to enumerate the problems encountered in cobalt recovery from the copper concentrate under actual mill conditions; to present alternative solutions to these problems; and finally, to describe the best available technology for cobalt recovery within the imposed constraints. Mineralogical analyses showed the cobalt present as a distinct mineral phase, predominately siegenite, amenable to a physical separation method such as froth flotation. Flotation was chosen for recovery because of easy adaptation by the mills. Unit processes of grinding, conditioning, and flotation were studied individually and in concert, and a series of continuous tests were run based on the parameters developed to obtain engineering data for subsequent economic analysis. Overall cobalt grades of 3.00 wt pct at a recovery of 64.0 pct were achieved.

Jan 1, 1987

By Steven Gillgrass

Gerdau Monroe has installed and commissioned the Tallman Supersonic Carbon Injection system (TSCi™) for use in their 135-ton Electric Arc Furnace (EAF) located in Monroe, MI. TSCi™ is an innovative injection system with the primary aim of improving injection carbon delivery to the steel bath by increasing efficiency. It is proven technology with installations at numerous steelmaking facilities all over the world. Results from installation and commissioning of TSCi™ at Gerdau Monroe will be reported as well as on-going trials and optimization efforts. Standard injection systems deliver carbonaceous material from a vessel to the EAF using air where it is injected through a lance pipe or oxy-fuel burner. Using this method, material delivery to the EAF is limited by the pressure and velocity of the transport air. Loss of efficiency can be observed by looking at the quality of the injection carbon stream during operation or by measuring loss on ignition of EAF slag or off-gas system dust. TSCi™ uses a patented design and proprietary technology to improve delivery of carbonaceous material to the EAF. Using this method, savings at Gerdau Monroe were realized by reducing the amount of carbon used in each heat while maintaining or improving upon existing foamy slag practice. As well, significant savings were achieved as a result of reduced FeO content in the slag and improved recovery of iron. Additional savings can be realized by using a smaller mesh material to take advantage of lower material cost and higher injected surface area. Other inherent benefits to improved injection carbon include lower energy and electrode consumption, reduced refractory wear and reduced maintenance cost.

Oct 30, 2017

By Prasenjit Basu

Drilled displacement piles are being increasingly used as foundation elements, particularly in projects requiring fast construction. Different types of drilled displacement (DD) piles are available in practice. DD piles are classified according to the drilling tool design and installation method. The capacity of a DD pile, depending on its type, is between the capacities of geometrically similar nondisplacement and full-displacement piles installed in the same soil profile. This paper provides an overview of the different types of DD piles and their installation techniques and describes three design methods used in practice. It also compares DD pile capacities obtained with these design methods for two different sites.

Jan 1, 2010

By S. B. Bealko

In response to recent mining disasters and new mine rescue team legislation, NIOSH researchers conducted meetings across the United States with mine emergency response experts to investigate current needs and issues. Some of the issues include emergency response preparedness, mine rescue contests, real-life training capabilities, and training facilities. Many new teams are being formed that must be trained for mine rescue team competitions as well as be ready to respond to a variety of mine emergencies including a fire or explosion, a massive roof collapse, mine inundations, or vertical shaft rescue situations. Therefore, it is important that these teams are adequately prepared and trained. This paper presents a summary of domestic and international coal mine rescue training facilities and identifies those that provide unique, real-life, and/or state-of-the-art training. Research findings from this report will be used in further NIOSH investigations to improve coal mine rescue training. DISCLAIMER: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By Margarete Kalin

"Biotechnological approaches to decommissioning of mine waste management areas are presented in the context of sustainable environmental management. Improved design of waste sites and environmental management paves the way for the application of new technological approaches. Mining wastes are better confined, effluent quantity is reduced and the quality is expected to improve in the future. The biologically mediated treatments focus on the creation of conditions inside the waste management area which lead to the confinement of the contaminants in the inactive tailings ponds and seepage collection ponds, as well as pits or other disturbed areas which were part of the operating conditions.Biogeochemical reactions lead to three fundamental water treatment steps mediated biogeochemically , alterations in chemistry which lead to formation of particles, which then have to flocculate and be assisted to collect in the bottom of the ponds. Microbially active sediments are installed to assist particulate formation and serve as sinks for metals. In deeper sediment strata, stable forms of metals are created. Biological polishing is used to collect the particulates and relegate them to the sediment. Examples will be given of the application of these processes, to waste rock piles, open pits and tailings ponds. This paper attempts to show that, through the integration of applied biotechnological advances and the application of new approaches to decommissioning, reductions of environmental impacts by mining are possible. * Note: this paper has been presented at the 13th Annual Meeting of BIOMINETIntroductionThe role of biotechnology in decommissioning of mining waste management areas should be placed in the context of sustainable development. The concept of sustainable development as defined by the Brundtland Commission (1987) for the restoration/ reclamation of mining operations could be translated as follows: The increasing demand for the resources by the world population must be met in a manner which does not compromise the earth's environment over the long term (Brooks et al., 1995)."

Jan 1, 1998

By Bolestaw A. Ktosihski

Preloading of bored pile bases by grouting is an effective way of reducing foundation costs. The bearing performance of a pile may be considerably improved. Various techniques and devices are used. Preloading of a pile base by a special grouting installation is preferred. The grouting device consisting of a U-shaped grouting tube with sleeves and a plastic membrane, separating the tube from the pile concrete, has well proven in Polish practice. The preloading may raise the pile design loads by as much as 30%, and increase their stiffness by 50%, in suitable conditions. The preloading equalizes the deformability of piles in a foundation or a structure. Examples of the base preloading use and load tests of base grouted piles are presented.

Jan 1, 2006

By Michael J. Sapko, William D. Monaghan, Michael A. Trevits

Mine seals are used extensively in underground coal mines to segregate mined-out areas and to isolate fire zones or underground areas that are susceptible to spontaneous combustion. Over the years, 30,000 mine seals have been erected in underground coal mines in the United States. Mine seals, along with rock dusting and ventilation, represent the fundamental means of preventing underground coal mine explosions. In this study the National Institute for Occupational Safety and Health (NIOSH) used ground penetrating radar (GPR) technology to determine if each of three test mine seals were uniformly constructed. Three mine seals representing different construction methods and materials (cast-in-place foamed cement; solid block, polyurethane foam and gravel; and wire mesh, rebar and gunite) were erected at the NIOSH Lake Lynn Laboratory’s underground mine as part of an on-going research program. The seals were imaged using GPR with 400-, 500-, 900-, and 1,000-MHz antennas. We found that variations in uniformity existed in the material for the cast-in-place foamed cement seal. Variations in uniformity also existed in the seal made from solid block, polyurethane foam and gravel. The post-processed radar records correlated closely with recovered core samples (areas of gravel and polyurethane foam, and areas containing only polyurethane foam). Finally, the radar records of the seal made of wire mesh, rebar and gunite showed the various components. The results of this work suggest that GPR could be used as a tool to evaluate mine seal characteristics and construction uniformity.

During recent years there has been a marked increase in the use of explosives in Queensland coal mines. Delay detonators have been introduced and their use has extended with the wider application of mechanised methods of mining.The need for careful study of the characteristics of delay detonators is stressed so that the advantages of simultaneous firing, from the points of view of safety and efficiency, may be obtained. With their use new potential hazards are introduced. These hazardsare considered and means whereby the overall safety may be improved are discussed.The increase in the number of misfires since the introduction of delay detonators is shown and the examination of misfired detonators is described. Lessons to be learned! from these misfires are noted and details are given of the essential requirements for safe and efficient blasting using delay detonators.INTRonUCTIONOne of the aims of mechanization in coal mines is to reduce the physical effort applied to the winning of coal. Explosives play an important part in achieving this and, following the introduction of power borers for the drilling of shot-holes in Queensland coal mines, much of the arduous work associated with coal getting has been eased. During recent years there has been a marked increase in the consumption of explosives, as shown in Table 1, and it must be the aim of all to use these explosives safely and efficiently. That there are dangers associated with the use Of explosives cannot be denied. The shotfiring operation is fully covered by legislation and, being under the control of one man, shQuld be capable of being carried out with a high degree of safety. The main source of accident appears to be the failure to take proper cover and this has resulted in...

Jan 1, 1958

By M. Abdellatif

Keywords: Magnesium, pyrometallurgy, Mintek Extensive testwork on atmospheric thermal magnesium production has highlighted certain important fundamental and operational factors that have a major influence on magnesium extraction and its extraction rate, the condensation efficiency of magnesium, as well as on the quality of the condensed metal. The possible impact of these factors on the selection and preparation of raw materials, recipe choice, furnace electrical energy consumption, and on the refining requirements of the crude magnesium is discussed. Selected pilot plant operational and metallurgical data are also presented.

Jan 1, 2006

I have chosen this subject in view of the fact that, while there are many and ample opportuuities of getting reliable assays made, there are but few who are in a position to obtain reliable data on the sampling of minerals and metals my long experience at Port Pirie, where, for five years, I had charge of the Refining and Sampling Mill, showed me how important it was that a correct sample should be taken.Weighing; This, to the ordinary layman, seems so simple that no expert knowledge is needed, but in actual practice there are hundreds of pounds to be lost by the lack of knowledge in this department.(1.) There is the matter of weighing in large or small quantities.(2.) The class of weighing machine used.(3.) The accuracy of weights used.We all know that, say, 1000 tons of ore cannot be weighed in one parcel; but the fewer the weighings the less loss to the seller (and usually wishes it weighed in small lots carefully) for it is a well known fact that the most sensitive scales take a certain weight to show distinctly the indication of the balance, or, in other words, what is known as "the pull of the scales." As for instance, 1000 tons weighed in lots of 1 c. each, taking the pull of the scale as being equal to 1 lb., would give a result of 9 tons loss to tbe seller, and as most of the ore sent to Customs works is worth 5. -£20 per ton-this would mean £180 loss to the careful man.

Jan 1, 1901

A201 aluminium alloy is a high strength casting alloy with a nominal composition of Al-4.6Cu-0.3Mg-0.6Ag. It is strengthened by the O(Al2Cu) phase and the ??(Al2Cu) phase during heat treatment. Further strengthening of this alloy system can be obtained through the addition of transition elements, but care must be taken as other elements might have adverse effects on the mechanical properties. The objective of this study is to determine the influence of Mn on the tensile properties of rheo-processed Al-Cu-Mg-Ag alloy A201. ThermoCalc software was used to predict the different phases that can be expected in the alloys, and scanning electron microscopy(SEM) with energy dispersive spectroscopy (EDS) was used to investigate the actual phases that formed. The influence of these phases on tensile properties is quantified. SEM and ThermoCalc revealed that there is an increased amount of the Al20Cu2Mn3 with increasing Mn. The tensile properties showed that high amounts of Mn do have adverse effects on the tensile properties of alloy A201, especially the ductility. Keywords Semi-solid metal (SSM) forming, alloy A201, intermetallics, Al20Cu2Mn3

Jan 1, 2011

By M. Natarajan, C. J. Cutler, E. Mponda

Keywords: Pyrometallurgy, furnace, KCM Nkana, Zambia The Nkana smelter was initially commissioned in 1931, with two reverberatory furnaces, two Peirce-Smith converters, and blister copper casting facilities. Reverberatory furnaces were the mainstay of production up until 1994, when an El Teniente Converter (CT) was installed to upgrade reverberatory furnace matte to white metal, prior to converting in conventional Peirce-Smith (PS) converters. In 2000, a decision was taken to increase the proportion of concentrate smelted in the CT by introduction of bone-dry concentrate injection through the tuyeres. A flash dryer with a nominal capacity of 1 200 metric tons per day of dry product, and associated tuyere injection system was commissioned in March 2004. Based on the projected concentrate arisings from the KCM mines into the future, as seen in 2004, it was decided to develop the CT to be the primary smelting vessel at Nkana, to handle a minimum of 1 250 tons per day of concentrate, and to operate only one reverberatory furnace in slag-cleaning mode pending a full evaluation of alternative slag-cleaning technologies. The anticipated cathode production from Nkana was to be in the range 140 to 150 000 tons per annum. This paper details the outcomes from trials that were carried out in August and September 2004, using two reverberatory furnaces for slag cleaning. The results of these trials, plus further work in October and November, provided confidence to move to one reverberatory furnace for slag cleaning in December 2004. With the advent of Vedanta as the majority shareholder in KCM at the end of 2004, the approach has been to maximize the available smelting capacity. Currently, two reverberatory furnaces and the CT are on-line, with the higher silica concentrates going to the reverberatory furnaces with an appropriate amount of pyrite, and the cleaner concentrates going to the CT. Expansion of the smelter is currently under investigation.

Jan 1, 2006

By D. Loring, J. Almgren

Climax Molybdenum Company’s Henderson Mine is a large panel caving molybdenum mine located about 43 miles west of Denver, Colorado. Three Joy M120-72-880 fans are installed in parallel on the No. 1 exhaust shaft. Throughout the mine’s history, ventilation changes such as the completion of the No. 5 exhaust shaft have decreased the utilization of these fans. To optimize fan performance they have been run with the full complement of 16 blades, down to as few as four blades. Since the completion of ventilation upgrades associated with the Henderson 2000 project, one surface fan has been operated under normal conditions with 10 or 12 blades. With the completion of a new network model of the Henderson ventilation system, a tool was built to develop fan curves for possible future fan configurations and predict future fan performance. This paper describes the tool and its use at Henderson.

Jan 1, 2007

The Gippsland Basin, southeastern Australia, has an Upper Cainozoic history of episodic change of hydrology and the related environment, reflected in the geomorphology and surficial deposits of the onshore basin and the hydrodynamically controlled accumulations of petroleum of the offshore basin. Succeeding this episodic pattern, man through a number of activities, has had a sudden and major impact on the hydrology and the related environment. Activities include those directly affecting the groundwater system, such as extraction of fossil fuels with the consequent threat of land subsidence; irrigation and clearing of vegetation and the consequent effect of salinisation; change of land use and installation of septic tanks with resulting nitrate pollution; damming of streams and the consequent reduction in the frequency of floods with degradation of the biological Environment; de-snagging streams and construction of cutoffs with increased stream erosion, modifying wetlands including drainage, with the consequent degradation of their ecosystems; and increase in phosphate and nitrate inputs to the coastal lakes with the risk of their eutrophication.

Jan 1, 1992

By Keith A. Heasley

In the past, numerous displacement-discontinuity (DD) models of stratified rock masses have been proposed using a homogeneous isotropic elastic overburden. In this paper, it is postulated that a laminated overburden model might be more accurate for describing the displacements and stress in these stratified deposits. In order to investigate the utility of using a laminated overburden in a DD model, the fundamental mathematical basis of the laminated model is presented and graphically compared with the fundamental behavior of homogeneous isotropic elastic overburden and with field data. Specifically, the stresses and displacements surrounding an idealized longwall panel as determined from the laminated overburden model are presented and compared with results from the homogeneous isotropic overburden and with measured abutment stress data. Also, the remote displacements and surface subsidence as calculated by the laminated overburden model are compared with homogeneous isotropic calculations and with measured subsidence data. The results of this investigation show that the laminated overburden is more supple, apt to propagate displacements and stress further, and better able to fit observed data than the classic homogeneous isotropic overburden. Ultimately, it is suggested that the laminated model has the potential to increase the accuracy of displacement and stress calculations for a variety of mining situations.

Jan 1, 1996

By D Gelling

Mineral sands dry plants consist of a large number of repetitive unit operations with significant transport delays, in the form of stream pipes, conveyors and elevators. As part of the P255 mineral sands sponsorship and using the JKMRC developed conductor/non-conductor (CNC) gauges, control loops have been implemented at the multi-duty dry plant of Cable Sands Limited at Bunbury. This paper describes the loops for kV control on a rougher high tension roll machines (HTR). The options available are product grade control and ratio control using the JKMRC CNC gauges, which measure the percent conductors in a stream. The purpose of control is to stabilise the circuit operation against disturbances such as atmospheric and feed disturbances.

Jan 1, 2001

By Vidyaranya Bandi, Madhav Madhira, Kota Vijay Kiran

"Using hyperbolic relationships for the non-linear responses of shaft and base resistances, a method is proposed for estimating initial shaft and base stiffnesses and ultimate shaft and base resistances of a pile from pile load test results. An iterative procedure is used to arrive at the values of shaft-soil and base stiffnesses and the ultimate shaft and base resistances. The method is applied to load - displacement data available from pile load test results to illustrate its efficacy.INTRODUCTIONA pile foundation is the most effective and economical solution in transferring large vertical loads to deeper depths. As the pile is subjected to axial load, the soil mass surrounding the pile is vital in providing vertical support for the pile. The nature of pile–soil interaction is three dimensional and to complicate the problem further, response of soil is nonlinear. Finding a closed form solution to such problem is extremely difficult. Several methods were developed to study and predict the response of the composite pile–soil system. Faruque and Desai (1982) implemented both numerical and geometric non-linearities in their three dimensional finite element model. Rajashree and Sitharam (2001) developed a nonlinear finite element model of batter piles under lateral loading using a hyperbolic relation for static load condition and modified hyperbolic relation, including degradation and gap for cyclic load condition.The ultimate capacity of the pile is estimated considering the strengths and unit weights of soil layers with depth, overburden pressure and other relevant parameters. The estimated capacities always need to be validated by conducting initial maintained load test. The estimated capacity may differ with the actual at site since the values of strength, stiffness, interface resistance between pile and soil, lateral earth pressure coefficient with depth and soil stratification, etc., differ from the design parameters considered for estimating the ultimate capacity of pile. The estimation of axial capacity of piles involves considerable uncertainties in selection of appropriate design parameters and the design rules are not always consistent with the installation procedures/processes involved."

Jan 1, 2017

By T. van Heerden

A range of supported gold catalysts was prepared by ion exchange, varying many of the preparation variables, including concentration in the precursor solution, washing procedure, as well as drying and calcination procedures. These catalysts have been characterized extensively. TEM images show essentially the same crystallite size distributions, between 2?5 nm, for almost all catalysts, the only exception being catalysts not washed in ammonia, which did not show any small crystallites. Additional characterization with SEM yielded an interesting discovery. Catalysts that appear identical on the TEM also contain some large crystallites in the range of 50?500 nm. Differences in dispersion due to the drying procedure not seen on the TEM can now be observed. Oxygen chemisorption is being investigated as an additional method to characterize gold based catalysts to complement the typically used electron microscope techniques.

Jan 1, 2012

Mineral ownership determination is not always straight forward as in many cases the relevant details are not recorded on the latest Land Transfer title held in the local Land Registry Office. To determine mineral ownership can be difficult, time consuming and expensive especially in a confused sector. Non statute minerals can be owned by the Crown, Land Owner or other persons. Statute minerals (Gold, Silver, Petroleum, Uranium) are always owned by the Crown and thus present no problems. In simple terms the only accurate and reliable method of determining the mineral ownership under subject land is to historically search back to the first registration when the land and minerals were definitely intact. Then carefully ascertain from the evidence gathered along the way to the present day whether any legislation or private agreement altered or affected the status quo.

Jan 1, 1998

By P. J. N. Pells

A good thing is becoming a bad thing. Rock mass classification systems, that are so excellent for communications between engineers and geologists, and that can be valuable in categorizing project experience, are emasculating engineering geology and rock mechanics. Some engineering geologists have been sucked into thinking that Q and RMR values are all that is needed for engineering purposes, and seem to have put aside what can be learned from structural geology and geomorphology. Many rock mechanics engineers seem to have forgotten the scientific method. This paper attempts to redress the situation by showing how mechanics can be used in rock engineering to design with a similar rigour to that used in the fields of structural engineering, hydraulics and soil mechanics. It also attempts to remind practitioners of what can be achieved by skilled engineering geology.

Jan 1, 2008