Search Documents

By Jeon Jeon, Yong-Kun Choi, Chung-In Lee, Yong-Hun Jong, Hag-Soo Kim

In this study, a computer program to design tunnel blasting pattern has been developed. The program consists of two parts; one is for tunnel blasting pattern design and the other is for blasting modeling to estimate the peak particle velocity, the distribution of fragmentation and the excavation damage zone. We modified the design method of tunnel blasting pattern suggested by Langefors because it provided undesirable pattern in blasting practices such as considerably large center cut and too large burden for Vcut as drilling length increased. As a result, the burden and spacing were reduced to practically appropriate amounts. In addition, the correlation between rock mass rate, RMR, and rock constant in blasting, c, was analyzed based on the data collected from twenty three tests of tunnel blasting. It was concluded that the correlation between them was fairly good enough to be applied in cut design. In order to check the validity of the modified methods and their practical applicability, test blasting was carried out at two different tunnel construction sites in Korea. The results were satisfactory in that the average rate of advance was 90% and the overbreak did not cause additional support. Futhermore, the developed program is capable of estimating peak particle velocity by using (a) the existing vibration equations, (b) the vibration equation obtained by test blasting to check out the practical applicability of the designed blasting pattern. Feedback is implemented into the program to adjust the designed blasting pattern and control the vibration.

Jan 1, 2005

By William J. Krisko

This contract final report summarizes the design, fabrication and testing of canopy air curtain devices under Bureau of Mines Contract H0232067. The canopy air curtain device is designed to reduce the level of respirable dust exposure to a continuous mining machine operator while having a minimum effect on operator safety, mobility and comfort and being compatible with mining equipment. This contract was devoted to the development of a device which utilizes an invisible curtain of air to envelope a mining machine operator's breathing zone with filtered air to provide respiratory protection. Various concepts were evaluated by means of laboratory tests. One concept was selected and was tested on various mining machines at underground sites by means of MSA personal samplers. The canopy air curtain was found to be effective. The percent reductions over the ambient dust concentrations were about 30 to 75 percent depending on the amount of time the operator spent under the air curtain. At one test site, the device enabled the mining machine to operate within compliance. Donaldson Company is presently working on the commercial production of the device.

Jan 1, 1975

The increased focus on best practice environmental management has led to mining and mineral processing companies developing a variety of procedures to ensure that the environmental impacts of their operations are minimised, and that company managements are fully aware of these impacts and the policies and procedures established to ensure this process. Parallel to this, international standards for the development and implementation of environmental management systems are being promoted as necessary for companies to demonstrate their due diligence. Good environmental management systems should be built upon the systems already established within companies, and should ensure that the process of continual improvement is integral to their operation. An outline of the basic components of environmental management systems is provided, along with examples of the way various mining companies have implemented such systems. The benefits of best practice environmental management to mining companies are also considered.

Jan 1, 1995

By Alaina B. Hanlon

Keywords: Undercooling, Convection, Dendrites, Stainless Steel, Levitation Certain Fe-Cr-Ni stainless steel alloys solidify from an undercooled melt by a two-step process in which the metastable ferrite phase forms first followed by the stable austenite phase. Recent experiments have shown that the lifetime of the metastable phase is strongly influenced by flow within the molten sample. The current research will provide insight to why flow affects the metastable phase. This new understanding will lead to the use of convection to control microstructural evolution in spray-forming of stainless steels. Simulations using a commercial computational fluid dynamics package, FIDAP, yield a range of convective flow velocities that cause mechanical damage to the dendrites which is compared to experimental results. If the convective velocities are great enough that the dendrites bend, then low angle boundaries form at the points of collision. These result in high energy sites that could serve as nuclei for the stable phase.

Jan 1, 2005

By G T. Kukla

A Seam deposit User oriented Mine Planning System (SUMPS) was developed by The Broken Hill Proprietary Company Limited (BHP) at its head office in Melbourne. It is one of the computer mine planning systems developed by the Corporate Data Processing (CDP) section of BHP. To date it has been employed in the feasibility study of four coal prospects for the BHP Group, including Gregory in central Queensland û Ham and Van Hoorn (1978). It was also used in detailed short term mine planning for Gregory. A recent application was in the feasibility study of Saxonvale, a multi seam coal deposit in New South Wales with seams up to 20 m thick. The other two applications of SUMPS were also on thick multi seam coal deposits. Development of programs for the underground subsection of SUMPS is continuing. SUMPS was developed and implemented on mini computers with graphics and plotting peripherals. The company's philosophy towards computing is one of centralized development and project planning, with transfer of hardware and software to site once the mine becomes operational. Support of the site's system continues from head office which is continually involved in development of SUMPS and issuing revision updates to sites. The users, as well as programmers, were mostly geologists and mining engineers. This helped to ensure rapid, successful implementation. The broad approach of this system was to use interactively the specialist skills and interpretative abilities of the user mining engineers and geologists with the data manipulation abilities of the computer. It is an integrated system which covers geological exploration, deposit modelling, mine planning and production scheduling. An important feature of the system is that the user has full interactive control over each function through a graphics terminal where applicable.

Jan 1, 1980

By K. Boakye

This paper presents the results of a review of historic blast design practices at the Dragon Products Company, LLC (Dragon) Quarry Operation, along with the results of two different blast design vibration monitoring programs. A blast pattern design modification was initiated to determine if production volume per shot could be increased and highwall instability could be decreased. A vibration monitoring program was undertaken to investigate peak particle velocity (PPV) and relate the data to the blastability of the jointed onsite rock mass, utilizing the relationship between PPV and dynamic stress and strain. The Dragon Quarry Operation has historically used a 6-in. diameter, 14-ft by 14-ft production blast pattern, with blast holes loaded manually using cartridge style explosive products. In 2011, Quarry Operations introduced a 6-in diameter, 16-ft by 16-ft production blasting pattern, using pre-mixed, truck-loaded, bulk emulsion/ammonium nitrate/fuel oil (ANFO) blends. This paper summarizes the results of the blast design modifications, the results of the vibration monitoring data, and describes how production blasting and excavation at the Dragon Quarry has benefited from such modifications.

Feb 27, 2013

By J. Kretschmann

Around the world, mining has been done for thousands of years for the benefit of humankind. The winning process in mining operations ends with the depletion of the deposit or its closure if the operation becomes economically unprofitable. After that, a period of post-mining follows which may last for a very long time and which is generally regarded as a period of hazards, risk and high cost. In the USA alone, approximately 500,000 abandoned mines do exist; worldwide, there are millions. In Germany, too, we have had to deal with abandoned mines for a considerable period of time now.

Jan 1, 2012

Mercury has been used by mankind since prehistoric times. It has been, and is now, widely used in industry and medicine and has unique properties which make direct substitution difficult or impossible. At present its principal uses are for electrical apparatus, control instruments, electrolytic soda preparation, mildew-proofing paints, pesticides, and medical and dental preparations. Deposits of mercury are less common than those of other base and precious metals, but some of the deposits are very large and have been ample to meet the world's past demands. The price of mercury has had many sharp fluctuations, but in general, the limited number of producers has resulted in a more stable price structure than that of many other commodities. The United States has been one of the main producers of mercury, and from 1850 to 1961 produced 3,247,704 flasks. Yearly production since World War II has varied from 4,535 to 38,067 flasks. An estimate of domestic resources of mercury producible at various price ranges was prepared for each mercury mine by combining specific knowledge of mercury mineralization with estimates of potential, based on geologic information and past production history. The sum of the individual estimates for each price range is shown in a table. A parallel estimate of nationwide production potential was made from a study of past price and production relationships. These were analyzed by plotting yearly production figures against the previous year's price, expressed in dollars of constant purchasing power. An equation was fitted to the data by mathematical means and was used to extend the curve into areas of higher than historic prices. Potential production rates at various price levels were taken from this graph. The estimated yearly production rates were used to make an estimate of total potential based on the premise that production rates and reserves have a proportionate relationship. The rate of developing mercury reserves during the period from January 1944 to January 1962 is considered, and it is shown that if this rate can be continued, the mercury resources of the United States, at a constant dollar price of $500 per flask, are adequate to support a production of 60,000 flasks per year for 30 or more years. This publication contains a history and description of the mercury industry in every State which has had production and individual descriptions of all mercury properties which have reported significant production. Accompanying tables give the important facts about all known mercury occurrences.

Jan 1, 1965

Mercury has been used by mankind since prehistoric times. It has been, and is now, widely used in industry and medicine and has unique properties which make direct substitution difficult or impossible. At present its principal uses are for electrical apparatus, control instruments, electrolytic soda preparation, mildew-proofing paints, pesticides, and medical and dental preparations. Deposits of mercury are less common than those of other base and precious metals, but some of the deposits are very large and have been ample to meet the world's past demands. The price of mercury has had many sharp fluctuations, but in general, the limited number of producers has resulted in a more stable price structure than that of many other commodities. The United States has been one of the main producers of mercury, and from 1850 to 1961 produced 3,247,704 flasks. Yearly production since World War I1 has varied from 4,535 to 38,067 flasks. An estimate of domestic resources of mercury producible at various price ranges was prepared for each mercury mine by combining specific knowledge of mercury mineralization with estimates of potential, based on geologic information and past production history. The sum of the individual estimates for each price range is shown in a table. A parallel estimate of nationwide production potential was made from a study of past price and production relationships. These were analyzed by plotting yearly production figures against the previous year's price, expressed in dollars of constant purchasing power. An equation was fitted to the data by mathematical means and was used to extend the curve into areas of higher than historic prices. Potential production rates at various price levels were taken from this graph. The estimated yearly production rates were used to make an estimate of total potential based on the premise that production rates and reserves have a proportionate relationship. The rate of developing mercury reserves during the period from January 1944 to January 1962 is considered, and it is shown that if this rate can be continued, the mercury resources of the United States, at a constant dollar price of $500 per flask, are adequate to support a production of 60,000 flasks per year for 30 or more years. This publication contains a history and description of the mercury industry in every State which has had production and individual descriptions of all mercury properties which have reported significant production. Accompanying tables give the important facts about all known mercury occurrences.

Jan 1, 1965

Stripping of Fe (III) from D2EHPA Using Different Reagents The common way to extract Fe(III) from an organic solvent is by using concentrated acidic solutions. The stripping of Fe(III) from organic solvent Di-2-ethylhexyl phosphoric acid (D2EHPA) by hydrochloric acid (HCl) solutions has been found to increase with increasing the acid concentration. However, the use of a concentrated acidic solution such as 6 M HCl can degrade the organic molecules. In this research, to increase the efficiency of Fe(III) stripping from D2EHPA, effect of some acids, salts and buffer solutions was studied. Influence of Tri-butyl phosphate (TBP) as modifier on the Fe(III) stripping operation was also investigated. According to the results, the best Fe stripping recovery was achieved in the presence of low acid concentration and the salts which was 72.4 per cent oxalic acid, 70 per cent ammonium oxalate and 75 per cent buffer of oxalic acid and ammonium oxalate. The results also showed a better recovery in the presence of the buffer rather than the salt. Finally, increasing the concentration of TBP, HCl and H2SO4 resulted in a higher stripping efficiency of Fe(III). However, in the presence of oxalic acid and its salts increasing the reagent concentration did not increase the stripping efficiency and at this condition, the recovery of iron remained constant.

Sep 13, 2010

By Reno M. Pappas, Christopher Mark

This report presents results of a U.S. Bureau of Mines study of longwall gob material. The objective of this work was to determine material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining. Photographs of actual mine gob were digitized to obtain approximate particle size gradations of gob material. The gradation curve was shifted down to a lab- oratory scale, and 20 uniaxial compression tests were conducted. Varying the maximum particle size was not found to affect the stress-strain behavior, but changing the gradation appeared to influence the stress-strain behavior. The stress-strain relationship of the simulated gob material was nonlinear, the stress-secant-modulus relationship, was approximately linear, and the stress-tangent-modulus relationship was approximately a second-order polynomial function. Equations were generated from these curves, providing numerical modelers with a means to estimate gob moduli based on the stress level. In addition, the experimental data were statistically evaluated using multiple regression analyses, producing a series of equations to predict the secant and tangent moduli from the given stress level, bulking factor, rock strength, and thickness-to-width shape ratio of the particles.

Jan 1, 1993

By Madgwick J. C

Microaerobic biodegradation oflow-grade manganese dioxide slurry tailings was demonstrated in enrichment cultures treated with dilute molasses at 30°C and pH 5·8. Supplementary nitrogenous nutrients, yeast extract addition and pH adjustment were not required.Continuously stirred, air-limited reactors were superior to still intermittently agitated cultures, in that, at 5 per cent (w/v) MnOz tailings and 5 per cent (w/v) molasses, the yield of 0.12 g Mn++/g molasses, the rate ofleaching of 1·06 g Mn++/l/d and a recovery of Mn++ of 58 percent from MnOz were 2·8 times, 1·7 times and 1·9 times greater, respectively. The best compromise in yield (0·45 g Mn++/g molasses) and rate ofdissolution (0·73 gMn++/l/d) was at 1 per cent (w/v) molasses in a stirred reactor.Where leaching organisms were separated from sterile ore by a bacteria impermeable membrane leaching was shown to be some 20 per cent due to diffusible metabolites and 80 per cent due to a direct contact between the bacteria and the ore particle's surfaces.

Jan 1, 1986

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By Patterson B. G

The small party of mining men who formed the original Mount Morgan Syndicate in 1882, commenced operations on the top of the mountain with what were practically nothing more than small hillside quarries, It was not until 1891 that underground stoping began, and open-cut mining therefore commenced with the commencement of operations. This hillside quarrying, however, seems to have been quite haphazard and unsystematic ; there is no trace or sign of any properly devised mining scheme. This can be seen plainly enough from an examination of old mine plans; for in less than five years after stoping was; adopted, the open-cut was down into the stoped-out ground. The following table, prepared from these old plans, shows the downward trend of the excavation in the past fiftyseven years:-

Jan 1, 1939

By Richard E. Bischke

Computer assisted finite element model analysis, originally developed to study stress distributions in aircraft, has been modified into a versatile mining program, that can be used to assist the engineer with predictions of mine subsidence. International Exploration, Inc. has developed an in-house finite element model program which incorporates a multitude of factors influencing mine subsidence such as mine design, physical rock properties, structure, faults, joints and topography. Finite element analysis of a mine model can mathematically determine the magnitude and direction of the principal stresses within each of the elements forming the model. By comparing the calculated in-situ stresses to the actual rock strengths, high risk regions within a mine can be identified. These potentially unstable regions of the mine can be allowed to fail within the model and the resultant stress redistribution and element movement calculated. Thus, the effects of the mine collapse at the surface can be predicted for the purpose of determining the potential damage, if any, that could occur to surface structures from deep mine failure. Stabilization materials can also be mathematically inserted into the model to design and analyze the effectiveness of subsidence prevention programs. Two examples are presented of the finite element program being used to predict mine subsidence at substantially different geologic and mining provinces in Pennsylvania.

Jan 1, 1984

Background information, formulae and a systematic set of procedures for estimating capital and operating costs for open pit mining equipment are presented in this paper. Firstly, equipment capital costs are required. These can be obtained from either suppliers, contractors or from first principles. The equipment is then divided into cost elements. Typically these are fuel and power requirements, spare parts consumption, wear items such as tyres, teeth and drill bits and finally repair and operating labour requirements. By consideration of the cost and life of each element a base cost can be derived. The base cost is then adjusted to suit specific site conditions such as the proximity to spare parts suppliers, the duty or ground conditions and the management and operator skills specific to the site. Hence, the same item of equipment can be costed to reflect different operations. Included are tables and data for typical plant items. Several examples are also given to illustrate the methodology being presented. The intention is to provide a set of procedures to allow costs to be built up from base level in a systematic and repeatable way. Applications for these costs include feasibility studies, budgetting and data for economic analyses.

Jan 1, 1990

By R. M. Cooper, H. K. Herbert, D. N. Phillips

A study was carried out to determine the effects of adding CaCO3, Fe, Al and CaSi2 to the ladle, rather than to the raw materials, in order to increase the concentration of Ca, Fe and Al in the final product to meet customer specifications at Simcoa's Kemerton plant in Western Australia. LA-ICP-MS, SEM-EDXRA and ICP-AES analysis of samples and controls showed that the technique is suitable for controlling minor element concentrations. Iron was successfully added, while calcium silicide with aluminium proved better than limestone with aluminium for controlling Ca and Al concentrations in the silicon

Jun 19, 1905

By Henri Fredriksson, Rami Saario, Mark Weatherseed, Juri Matinheikki

"The challenges facing the mining industry include complex ores and declining grades, together with increasing capital costs and environmental regulations. In addition, future commodity price uncertainty makes investment decisions difficult. Shorter plant lifecycles mean that new projects need shorter payback and increased net present value. With regard to solvent extraction, the introduction of an innovative modular plant design will help to address these issues. The first such modular offering is Outotec’s VSF®X modular solvent-extraction plant that uses prefabricated and transportable modules. Reuse and recyclability have underpinned the design concept. The greatest advantage of the VSF®X modular solvent-extraction plant is its relocation possibility. Additionally, it is suitable for various metals and plant capacity is adjustable through a scalable modular structure. After a dedicated plant lifecycle, the plant can be dismantled and relocated to a new site. This reuse ability offers major benefits for short-term plants, making them more feasible due to higher residual value. A net present value analysis is made for two examples, a conventional plant with no relocation possibility and a modular movable plant with extended plant life cycle, in order to evaluate the feasibility of modular plants. Results indicate that modular plant design could offer an economical solution with the additional advantage of improved overall sustainability through its life cycle. INTRODUCTION The challenges facing the mining industry include complex ores and declining grades, together with increasing capital costs and environmental regulations. In addition, future commodity price uncertainty makes investment decisions difficult. Shorter plant lifecycles mean that new projects need shorter payback and increased net present value (NPV) (Mudd, 2010; Norgate & Jahanshahi, 2010) . Awareness of sustainability issues is also rising and sustainability reporting is now a key element of many companies’ public and investor relations. Major companies are now putting more effort in this area to earn legitimacy for new projects (Mudd 2010)."

Jan 1, 2015

By Wendy L. Naysmith

This paper deals with the various options considered and factors that influenced the final selection of the headframe, shaft layout and hoisting systems required at the Impala No 16 Shaft in order to hoist both the required 3 Mt of ore per annum, and transport men, material and equipment between the surface and the underground workings to a depth of 1640 m. The layout and construction method used for what is at present the world?s tallest concrete headframe is discussed together with the integrated hoist room foundations designed to suit multiple mechanical and electrical hoist supplier?s solutions. The mechanical components of the two tower mounted 6,5m 4 rope Koepe hoists and deflection sheaves and their layout is dealt with in detail. Various features of the bearing type, brake units and brake control system are also discussed. Installation of the mechanical and electrical hoist equipment in the headframe took place during the sinking phase of the project and placed severe restrictions on the use of the heavy lifting facilities. This required a well-managed and systematic approach to delivery of the hoist components and associated equipment, as well as close co-operation between all contractors on site.

Oct 1, 2010