Search Documents

By H. C. Counsell, R. Webber

"The mill at Denison Mines' Elliot Lake Operations started up in 1957, with a capacity of 6,000 tons per day. Over the years various plant modifications expanded th.is to 7 500 tons per day. In 1976, management decided to carry out a major expansion of the milling capacity, and during 1980 the grinding capacity was increased to 15,000 tons per day.The original comminution system consisted of a conventional crushing plant feeding minus S/s-inch material to rod and pebble mills, in closed circuit with mechanical classifiers. The key decision that had to be made was whether the expansion should include conventional or autogenous grinding flow sheets.During 1977, extensive pilot plant studies at Lakefield Research showed that two-stage semi-autogenous grinding, with some steel media in the primary mill and with pebble media in the second stage, produced stable grinding conditions. This type of circuit was selected by Denison for the expansion, and went into production in 1980. Primary millThe flow sheet of the semi-autogenous grinding circuit is shown in Figure 1. The primary grinding mill is a Koppers 28 foot by 10 foot mill, driven by a 4,000 h.p. synchronous motor. It is fed with a minus 8-inch run-of-mine ore, and 4-inch grinding balls are added as supplementary grinding media. There are two Koppers 15.5 foot by 22 foot secondary pebble mills, driven with 1500 h.p. synchronous motors. Each grinding stage operates in closed circuit with cyclones, and the primary cyclone overflow is the feed to the secondary mills. The circulating load in the primary stage can be controlled by adjusting the cyclone apexes."

Jan 1, 1984

By Klaus Pöllath

This paper describes mitigating measures and the design of compensation grouting which will be executed from deep shafts of the Amsterdam North/South Metro line project. Due to the specific conditions for TBM-tunnelling in Amsterdam (historical buildings on pile foundations near the tunnel and soft soils with high groundwater levels) tunnel construction necessitates mitigating measures, such as compensation grouting or soil freezing. Züblin developed a special shaft construction method for critical distances to buildings. For the compensation grouting Züblin developed a new software tool, called SOFIA, which controls and visualizes and thus optimizes the entire injection process. This tool significantly increases the efficiency of the injection works while reducing the geotechnical risks.

Jan 1, 2006

By L. Cheng

This report presents the results of a Bureau of Mines laboratory investigation of the effect of water sprays in reducing respirable dust that escaped the face area of a full-scale wooden model of a mine en-try containing a wooden model of a ripper-type continuous mining machine and exhaust brattice. Areas examined were (a) the general effectiveness of a low-pressure water spray system mounted on top of the mining machine boom, a high-pressure spray system mounted under the boom, and the combined top-and bottom-spray systems, and (b) the effect of these three spray systems on the capture of coal dust particles of different sizes. Dust was injected into a sump cavity at the face. Airborne respirable dust concentration was mea-sured behind the brattice with a personal sampler and cyclone, and particle size distribution was mea-sured with a cascade impactor. When used alone, the top-spray system captured about 55 pct of the respirable dust in the face area and the bottom-spray system captured 60 pct; the capture efficiency of each system is decreased when they are used simultaneously. From a mass-concentration viewpoint, each spray system preferentially captures larger dust particles.

Jan 1, 1988

Minerals are fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels?mining, processing and manufacturing finished products. The estimated growth rate for the real GDP of the United States was 2.1 percent and the nominal GDP was about $13.8 trillion in 2007 (Table 1). The prime interest rate decreased to 7.25 percent in December from 8.25 percent at the beginning of 2007, reflecting actions taken by the Federal Reserve Board to counter financial difficulties surrounding subprime mort-gages. Delinquencies on subprime mortgages increased throughout the year, affecting not only the delinquent home owners but also financial instruments invested in mortgage-backed securities. The average contract mortgage rate for the purchase of previously occupied homes in the United States was 6.35 percent in November; a slight decrease from 6.37 percent in January but still greater than 5.34 percent reported in July 2003, the lowest rate in the past five years. With the tightening of credit, the seasonally adjusted annualized rate for new privately owned housing starts declined 27 percent from December 2006 to November 2007. The loss in the residential market was balanced by a 9-percent increase in nonresidential construction between January and August 2007, during which slight increases occurred in nearly all

Jan 1, 2008

By Steve Dillingham

Blasting crews, explosive product drivers, drillers, blasters, supervisors, and salespeople all arrive daily at customer blast sites in vehicles of every type whether passenger cars, pickup trucks, or bulk trucks. The majority of these vehicles are company owned and re p re s e n t a substantial investment and risk for the company. That may explain why the costs resulting from blasting incidents is often surpassed by those involving motor vehicle accidents.

Jan 1, 2003

By Grant Loveday, Vincent Dieudonné, Andrew Jonkers

Bateman Minerals & Metals supplies the APIC Technologies which include the under-bed air-pulsed APIC jig and related technologies such as the JigScan controller and advanced mathematical models of the jig process. Bateman have developed a methodology for predicting process performance for jigs from simplified testing and modelling, based on batch equipment matched to industrial designs. Batch tests conducted on laboratory scale air-pulsed jigs can process small batches of material, such as those obtained from drill core samples. The novelty comes from using an advanced jig process model, ASTRAD, to link the results of batch and continuous jigs. The batch jig presented as a novelty in this paper has been designed to be hydraulically equivalent to the full-scale APIC Jig, allowing the generation of equivalent pulse shapes and using JigScan controller. Lump and fine ferrous ore material have been separated in this unit and any feed >1mm can be tested and extracted. The global test procedure and further modelling focus on the stratification of material, with emphasis on key aspects such as pulse shape, feed characteristics and residence time. The splitting of rejects from concentrates is itself more difficult to reproduce in batch jigging, however the ASTRAD model includes a separation imperfection module, and the APIC Technologies have extraction systems adapted to each type of material. Air pulsed batch jigs are available in several locations and are relocatable. They have been used to treat samples from Australia, South Africa and India as part of studies into ore processing using jigs. Each test layer is available for various physical testing procedures (density and chemical analyses). Test-work is performed on a case by case basis, and analysed using an advanced model ?now available over the internet. Some fundamentals of air-pulsed jigging are recapped along with some of the features of APIC jigs. The process of designing a ?hydraulically equivalent? batch jig test is then described. Some results from jigging tests are presented plus the results of the ASTRAD advanced jig model, which was first developed at the JKMRC with ferrous ores and coal and is now being supported and further developed and utilised by Bateman.

Jan 1, 2006

By Jiulong Cheng

Underground coal mining causes overburden deformation and failure, one major form of which is bed separation in the overburden. Surface subsidence can be controlled by injecting grout into the bed separations. For a long time, the grouting results of bed separation can not be validated. This is the problem in the application of this technique. This paper analyzes the conditions leading to bed separation, develops mathematical models for seismic wave fields generated before and after bed separation, and bed separations grouted with different materials, and computes the seismic wave field characteristics using the finite difference method. The results show that the existence of bed separation causes changes in the characteristics of seismic wave field, and that different grouting materials generate different seismic wave field characteristics. Intact strata, bed separation, and bed separation filled with air or water all display distinctive seismic wave field in amplitude and frequency spectra. After mining, the original location that provides strong seismic reflection wave no long exists. It is replaced by a weak and syncline-shaped reflection wave. The area, where the seam wave disappears, is larger than that of the mined area. The location, where a bed separation occurs, generates a set of reflection waves stronger than the normal one. The energy of the reflection waves varies with the materials filling the separations. Bed separations filled with air generate stronger reflection waves than those filled with water. The major frequencies for those filled with air are lower than those filled with water. Therefore, it is possible to determine the property of filling materials by analyzing and comparing the amplitude and frequency spectra of the reflection waves. Case studies of application of seismic method for exploring bed separations and grouting were analyzed. The results show that it is feasible to use seismic technique for exploring bed separations and grouting.

Jan 1, 2006

By None None

Life as a mining/mineral professional doesn’t leave much time for perusing 20-page technical papers. Yet, being technologically savvy is part and parcel of a successful career in this industry. What’s an intelligent, well-informed person to do?

By R. A. Westin

[Polychlorinated biphenyls (PCR's) have been widely utilised as fire-resistant dielectric coolants; in electrical equipment used in mining applicants, including transformers, capacitors, electric motors, and electromagnets. In addition, PCB's have been used in hydraulic fluids and heat-transfer fluids and are present in many oil-filled transformers. The U.S. Environmental Protection Agency (EPA) recently banned the manufacture of PCB's and equipment using PCB's, and imposed strict requirements on the continued use and disposal of existing PCB equipment. This manual discusses the EPA requirements, suggests ways to decrease the risks resulting from continued use of PCR equipment, and surveys the non-PCB equipment that is available as replacements for the PCB electrical equipment presently used in mines.]

Jan 1, 1980

By Robert H. Peters

The U.S. Bureau of Mines has prepared this report on strategies for maintaining high job attendance among underground coal miners because high absenteeism is a threat to miners safety and seriously hampers productivity. A substantial number of research studies on the effectiveness of various strategies for reducing absenteeism among the employees of nonmining industries have been reported in the literature. These strategies have aimed at improving job attendance through one or more of the following: (1) improving employment procedures, (2) overcoming problems that adversely affect one's ability to attend work, and (3) increasing miners motivation to attend work. Many of these strategies appear applicable to the mining industry, and are reviewed in the first half of this report. The second half of this report describes how one could develop and implement a program for maintaining high attendance at underground coal mines. The steps include: measuring and evaluating attendance levels; formulating attendance goals and an absenteeism policy; developing and implementing an attendance promotion program; and periodically going through the preceding steps known as recycling.

Jan 1, 1989

By Shimi Tzobery, Jay Davenport, Raymond Henn, Sam Bandimere

Over the past several decades, the use of cement-based grouts using ultra fine cement as a replacement for portland cement has begun to gain acceptance as an alternative to chemical solution grouts used in permeation grouting. The amount of information currently available on grouts made with ultrafine cement is limited. The authors used a previously developed field testing program to perform additional tests to evaluate the permeation performance of portland and ultrafine cement-based grouts. For the first time, the 2003 testing program included an attempt to determine the 28 day compressive strength of the sand permeated by the grout.

Jan 1, 2005

By John F. MacDonald

This paper describes the driving of a 400 m long by 25 m diameter highway tunnel through sensitive, overconsolidated silts and clays. The design concept requires the construction of the permanent support system, consisting of 24 concrete filled perimeter drifts, before excavating the mass core. General construction procedures used during the construction of the perimeter drifts are described.

Jan 1, 1985

By Patrice Favreau

In 1990 the Noranda Technology Centre commenced a project to develop an interactive three-dimensional blast design system using a commerical computer-aided drafting and design package (CADD). The objective was to alleviate the blast engineer from the tedious and time consuming blast layout and design functions normally done by hand. This would allow more time for optimizing blast designs through assessing multiple options. Since several blast design software "tools" already existed at Noranda, the need arose to integrate all the applications into one overall system that shared one common database. The result is BLASTCAD.

Jan 1, 1992

By L. W. Vigrass

Porous and permeable rocks deeply buried in sedimentary basins contain immense volumes of hot water with the potential to supply low-grade heat energy. A part of Canada with sizeable potential for low-grade geothermal energy is the northern Williston Basin of southern Saskatchewan. In this region, the University of Regina has conducted a geological study investigating the feasibility of producing large quantities of warm water suitable for space heating in the Regina - Moose Jaw area. The study has shown that the most favourable geothermal reservoirs are in the Basal Clastic Unit (Cambrian Ordovician), which, at an approximate depth of 2,000 metres has predicted temperatures of 71°C to 74°C. We anticipate sustainable flow rates from these reservoirs of 100 to 300 ms/hr. The water contains about 150,000ppm of total dissolved solids, mostly sodium chloride. It is anticipated that the sulphate content will be 3,000 to 6,000 ppm, that the dissolved oxygen and hydrogen sulphide content will be small, and that the waters will be neutral to slightly alkaline. It is anticipated that the piezometric level will be 46 m below the ground surface for reservoirs in the upper part of the Basal Clastic Unit and 141m below the ground surface for the lower reservoirs of the unit. Plans are to build a low-grade geothermal research, testing and demonstration facility at the University of Regina. To be a practical demonstration, the facility will have to handle very large volumes of water. Because of high salinity, the water will be re injected into a subsurface reservoir. We do not anticipate insurmountable problems because of salinities or as a result of corrosion provided that the waters are not aerated during handling

Jan 1, 1979

By R Simcock

Why Rehabilitate? Legislative Requirement Land rehabilitation is a condition of resource consents for mining. Clause 17 (1) of the Resource Management Act 1991 (duty to avoid, remedy, or mitigate adverse effects) provides the legislative basis for local authorities to impose resource consent conditions requiring land to be rehabilitated to approved uses during and after mining.

Jan 1, 1997

By J. He

The separation performance of a raw coal sample from South Africa based on the dense gas-solid fluidized bed beneficiation technique was investigated. Analysis showed that the raw coal sample distributes mainly in the -50+6 mm size range with the -1.6 g/cm3 density fraction accounting for 78.20% of the cumulative mass distribution. A flow sheet of the sequential coal beneficiation technique was introduced. The experimental and simulation results of the hydromechanical and density distribution stability indicate that the dense gas-solid fluidized bed could provide a stable separation environment with uniform density fluctuations under suitable operating conditions. With the application of this technique on the raw coal sample, the separation results show that three products, consisting of 73.25% clean coal with an ash content of 9.59%, 11.31% middlings, and 15.44% gangue were effectively separated at two different densities of 1.82 g/cm3 and 1.57 g/cm3. This study provides an effective flow sheet for achieving the high-efficiency separation performance on raw coal from arid areas. Keywords dense gas-solid fluidized bed, dry coal beneficiation, density distribution, separation efficiency.

Jul 1, 2013

By J. G. Kirby

The total number of petroleum refineries in the United States continued to decline during 1950, and according to the Bureau of Mines annual refinery capacity survey there were 357 refineries January 1, 1951, compared with 367 a year ago. The total throughput capacity increased 267,344 barrels daily during the year to 6,963,644 barrels daily as of January 1, 1951, continuing the trend of the past several years to increase the throughput capacity of the refineries and decrease the number of plants. The capacity of the average refinery to process crude oil increased during 1950 from 18,246 barrels daily to 19,506. The Indiana-Illinois refinery district accounted for 110,175 barrels, or 41 percent of the total crude-oil capacity increase, the Oklahoma-Kansas district, 17 percent, the California district, 14 percent, the East Coast district, 13 percent, and the Louisiana Gulf Coast district, 12 percent. Slight declines ill crude-oil capacity were reported in the Texas Inland, Texas Gulf Coast, New Mexico, And Appalachian refinery districts. The 160,100 barrels of additional crude-oil capacity that was building January 1, 1951, represents an increase of 10 percent over the year earlier figure. The only completely new refinery listed as under construct ion at the beginning of 1951 is located at Superior, Wisconsin. Other new construction involves enlargement of existing refineries. Plans for at least five additional new refineries are under consideration, and construction is expected to begin during the current year.

Jan 1, 1951

By A. Moskowitz, L. S. Redmerski

The corrosion resistance of stainless steels can be strongly affected by surface treatments. Changes in corrosion resistance can relate to surface composition, integrity and stability of the passive film, and to surface profile (roughness). Operations producing oxidation at the surface, such as annealing, heat treating, and welding, can result in a chromium-rich scale and a chromium-depleted metal surface. In order to restore full corrosion resistance, chemical or mechanical clean-up techniques must remove not only the oxide, but also a very thin layer of metal. Laboratory and field test studies show that these factors are particularly significant in less highly alloyed steels. Annealing stainless in a reducing atmosphere (bright annealing) avoids chromium depletion, but as-bright-annealed material does not display optimum corrosion resistance in certain environments. Electro passiva-tion can be applied to improve pitting resistance without significantly changing bright surface appearance. Potentiometric studies show that electropassivated material also displays significantly greater resistance to breakdown of passivity in acid solutions. The application of special surface finishes for appearance purposes can affect corrosion resistance. Roughness is a key factor. Samples of related appearance but with different surface profiles can show significant differences in corrosion resistance. Thus nonreflec-tive stainless with a relatively smooth surface produced by a special rolling process is much superior to material chemically etched to a similar low reflectivity. THE corrosion resistance of a stainless steel is affected by other factors in addition to its bulk composition and metallurgical structure. These other factors include those relating to the specific chemical and physical condition of the steel's surface. This paper will consider certain aspects of surface condition in relation to corrosion resistance. In particular, studies will be described on the effects of oxidation encountered in heat treating or welding operations, of passivation after bright annealing, and of different surface finishes. EFFECTS DUE TO OXIDATION When stainless steels are exposed to high temperature in an oxidizing environment, as in annealing or welding, the oxides formed are relatively rich in chromium. As a consequence of oxidation, the metallic layer directly beneath the scale may be low in chromium to some very thin but finite depth.1"8 Such a change in chromium content could lower the corrosion resistance at the surface, whether or not the oxide layer is removed. Studies were performed relating to the effect of oxidation and chromium depletion produced during annealing and welding on the corrosion resistance of stainless steels. The nominal compositions of steels used in this study and others are given in Table I. A) Annealing Studies on 17 pet Cr Steels. 1) Effects of Pickling Treatments. Studies were performed to investigate the corrosion resistance of air annealed type 430 stainless as a function of the amount of electrolytic pickling after annealing. The material used in this study had been air annealed and electrolytically pickled in the mill. All scale had been removed, and yet the material showed unusually poor corrosion resistance. Laboratory electrolytic pickling studies were performed to determine whether additional metal removal from the surface would improve corrosion resistance. Electrolytic pickling was performed in a sulfuric acid bath using various conditions of bath acidity, temperature, time, and current density. The samples were then rated for corrosion resistance in a ferric chloride spot test. For this spot test, a solution was prepared by dissolving 10 g of FeCl3 . 6H2O, 5 g of NaCl, and 2.5 ml of concentrated HC1 in 200 ml of water. An area on a specimen was cleaned and a drop of test solution was placed on the prepared area. After 5 min, the drop was rinsed off and the area wiped dry. The spot was then rated between 1 and 5 by visual comparison with standard spots. The numerical rating of the standard spots can be described as follows: 1—No clouding of surface; 2—very slight clouding of surface; 3—slight clouding of surface; 4—moderate clouding of surface; 5—strong clouding of surface. A rating of 1 or 2 was considered to have passed the test, a rating of 4 or 5 represented failure, and a rating of 3 was considered borderline. The severity of etching in this test has been related to the actual chromium content at the surface.4 Etching (clouding) occurs on type 430 stainless (rating of 4 to 5) when the surface chromium content is 14 pct or less. The effects of current density and retention time when electrolytically repickling this material in 6 pct sulfuric acid are shown in Fig. 1. Increasing the cur-rent density or retention time improved corrosion resistance as measured by the spot test. Similarly, increasing acid concentration of the bath or bath tem-perature was found to improve corrosion resistance. The conditions making for improved spot ratings resulted in increased metal removal, regardless of specific pickling conditions used, Fig. 2.

Jan 1, 1970

By D. M. Avant, A. J. Solomon, S. M. Pickering, W. R. Fox

Introduction Most high purity silica is produced from crystalline quartz, generally from sand. However, there is a small area of southern Illinois where a porous, friable white chert rock is found that is very different in physical form from quartz sand. This microcrystalline material, commonly referred to as tripoli, is more easily ground to micron sizes than sand. Although of similar Moh's hardness, microcrystalline tripoli is less abrasive than either ground quartz sand or many synthetic abrasives. Location The southwestern corner of Illinois is underlain by extensive deposits of very porous chert; in some places the material is quite white. Two companies, Illinois Minerals Co. and Tammsco Inc., mine and process this white material. The Illinois Minerals plant is located at Elco, and the Tammsco plant is in Tamms, IL. Both companies mine from various locations within a 10-mile truck haul of their plants. Production from this district has been continuous since at least 1915. Malvern Minerals Co. mines and processes a generally similar microcrystalline, friable novaculite near Hot Springs, AR. Geology The southern Illinois white tripoli area is on the southern flank of the Illinois Basin. The commercial silica zone is a facies of the Clear Creek chert of Lower Devonian Age. To the north, where it occurs deep in the basin, the Clear Creek is a siliceous limestone. In the mining area, thin overburden has allowed access by surface ground water, which has leached away the carbonate content and left a quite pure silica residue. Fossils characteristic of sea bottom deposition, such as brachiopods and trilobites, are occasionally encountered in mining. The structure of the mining area is poorly known, due to infrequent outcrops. Strata in most mines are inclined at dips of 5° to 20°. There appear to be occasional high angle normal and reverse faults, but these are seldom of any significance in mining. The friable white silica zone mined in the Clear Creek chert is overlain by dark brownish-red chert and siliceous shale. Exploration drilling to date has not encountered the base of the microcrystalline tripolitic zone. Chemical content Leaching by ground water solution has removed virtually all the carbonate from the original siliceous limestone. Impurities encountered are red to yellow iron oxides, aluminous clays, and occasional black manganese oxides. The silica has no detectable formula water. A typical chemical analysis and physical properties are listed in Tables 1 and 2. Mineralogy and crystallinity Southern Illinois friable tripoli appears amorphous under the polarizing microscope. No crystal structure and only occasional, vague, patchy anisotropism is evident. However, the material gives an excellent quartz X-ray diffraction pattern. Thus, so far as X-ray mineralogy is concerned, the material is clearly

Jan 12, 1986

By M. van Schoor

Coal remains South Africa?s most abundant and cheapest source of energy, and there is an ever-increasing necessity for optimal and safe extraction of the remaining reserves. Increasing focus on cost-effective mining and zero harm to the environment and miners has resulted in a shift in attitude towards the application of geophysics in local coal mining and exploration. Furthermore, technological advances have contributed to geophysics being embraced more readily by the coal mining industry, compared to a decade or two ago. Predictably, the growing interest in geophysical technologies has also created a need for education and training in the basic principles and application of geophysical methods, as local coal mining companies generally do not have in-house geophysicists. Consequently, the Coaltech Research Organisation?s Geology and Geophysics working group forum compiled a textbook aimed at addressing this need: to produce a guide for applying geophysics to coal mining problems in South Africa. The target audience for such a book would be coal geologists, mine surveyors, mine planners, and other mining staff with limited or no geophysics background. This paper provides a very brief overview of the book by summarizing key sections and selected examples. In doing so, the value of geophysics to solving a range of coal mining and exploration problems is highlighted.

Jan 1, 2014