Search Documents

By S. H. Jason Choi

The Systems Conveyance and Operations Program (SCOP) is being implemented to convey tertiary-treated effluent to Lake Mead near Las Vegas, Nevada. The Reach 3 Tunnel Project is part of SCOP. The tunnel?s planned location along and across the Las Vegas Wash creates challenging tunneling conditions. A number of feasible excavation and initial support methods are being considered during the final design stage. This paper describes how the tunnel construction options were refined based on anticipated tunneling conditions and compatibility between tunnel excavation and initial support methods. A brief description of the most significant characteristics of the anticipated ground conditions is included for the purpose of discussion.

By Frederic P. Dewey

This old and well-known method of determining silver is, in bullion work, so far superior to the furnace-assay that it is looked upon with reverential awe by many, if not by most, users, and its ease of execution, with proper equipment, commends it highly where much commercial bullion work on silver is required. The method is so thoroughly well known that a description of it here may seem to be unnecessary, but many thousands of determinations are annually made by it in the U. S. Mint Service and its practice is there reduced to an art. This is necessary both for the sake of economy of time, and because high-grade work with it requires constant practice. It is useless for a person who uses it only occasionally to expect to attain high accuracy with it, without spending more time upon a detemination than is warranted in a busy commercial laboratory. It is always employed in the Mint service whenever possible, but its chief field is in the determination of silver in standard silver (ingots and coin), which is 900 fine in silver and 100 fine in copper, and I shall first briefly outline its use on this metal and then take up various points in detail, especially as related to the accuracy of the results obtained. For this determination 1,115 mg. of standard metal are weighed and transferred to a glass-stoppered bottle, the metal is dissolved in nitric acid, and 100 cc. of a standard solution of NaCl run in. The bottle is then vigorously shaken and a measured portion of a decimal salt solution added, and again shaken, if necessary. These operations are repeated until the silver is precipitated. Standard metal being 900 fine, 1,115 mg. should carry 1,003.5 mg. of silver, which is a convenient figure to work with.

Jan 1, 1914

By Craig Bournes, David Chapman, Michael DiPonio

Historically, boulders are a frequent source of problems in soft ground tunneling. During tunnel construction, the need to manually break and remove boulders as obstructions causes delays to the project. Repairs to a tunnel boring machine (TBM) can also be a source of delays. Managing these problems is difficult since normal soil investigation techniques do not accurately predict the presence or frequency of boulders. This has lead to considerable number of claims for extra costs and delays during the construction of soft ground tunneling projects. These issues are exacerbated in pressurized face tunneling systems where there is limited access to the TBM cutterhead for obstruction removal and/or cutterhead maintenance. The project team that built the Big Walnut Augmentation/Rickenbacker Interceptor (BWARI) Project for the City of Columbus successfully managed the design and construction of a 4,267 mm (14 ft) diameter soft ground tunnel with high boulder concentrations in a complex geologic setting. The management of the boulder issue tookplace during several phases of the project.

Jan 1, 2007

By David Schlain

The Bureau of Mines investigated methods for electrodepositing platinum-group metals from molten cyanide baths. The preparation of thick, protective coatings on molybdenum, Inconel, graphite, stainless steel, copper, and other structural metals were studied, as well as the electroforming of platinum and iridium crucibles. Iridium, rhodium, and ruthenium can be electrodeposited under an inert atmosphere, while platinum and palladium require the presence of air. Electrolytes may be prepared by direct-current electrolysis in NaCN or mixtures of NaCN and KCN using anodes of the particular platinum-group metal. When the concentration of metal increases to about 0.3 or 0.4 percent, the deposits become bright, adherent, and coherent. Current densities may be 10 to 25 ma/cm2, and plating rates are often 0.5 mil/hr. Platinum and palladium baths deteriorate because of the oxidation of cyanide to cyanate and carbonate, and the precipitation of metal. Changes in the platinum cyanide bath are relatively slow. The protection against oxidation afforded by the platinum-group metal coatings is evaluated by testing encapsulated specimens in a thermogravimetric balance. Surface pretreatment and the use of undercoats are discussed.

Jan 1, 1977

Inhibition of Bubble Coalescence by Salts and Sugars

Sep 13, 2010

By Lutz Markworth, Wolfram Jaspers, Johannes Kottmann

PNEUFLOT® technology has been applied for the past 20 years in coal, ore and other minerals processing plants. During the last two years this technology has achieved a breakthrough with some 42 units being sold signifying a rising trend. »Humboldt Wedag Coal & Minerals Technology« has performed extensive research and development work over the last five years. The results of which were used to design a new fourth generation aerator. Humboldt Wedag, through its association with EKOF, can offer a holistic solution encompassing both flotation equipment and reagents. It is the only company in the world able to offer such a package. The association with EKOF strengthens the Humboldt Wedag product offering, especially as the company in-troduced pneumatic flotation cells to the South African market in the form of the PNEUFLOT®. Before starting pilot scale test work, a mineralogical analysis has to be carried out to determine the mineral com-position as well as the liberation grade. HW-CMT works together with independent institutes. Different reagent regimes can be tested in laboratory scale. Pilot machines, each packed in a 20? container, are available to carry out extensive test work at customers? processing plants. A group of engineers from HW-CMT is involved in the pilot test work. The flexible pilot machines are designed to cater for coal, ores and other minerals. The small feed rates of 7 ? 12 m³/h only means the pilot machines do not disturb the operation of process plants. Batch tests have to be carried out to determine the numbers of PNEU-FLOT® stages. New applications in iron ore, copper ore, platinum group minerals, rock phosphate and potash were suc-cessfully tested in the last three years. In applications where the feed material is very fine, PNEUFLOT® technology is able to achieve high recoveries with particle sizes where conventional technology failed.

Jan 1, 2007

By S M Richardson, A W McNeill, J B. Gemmell

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Hellyer, Fossey, Que River and Mount Charter volcanic-hosted massive sulfide (VHMS) deposits occur within the Que-Hellyer volcanics of the Mount Read volcanics, Tasmania. These deposits occur along a 6 km strike length and are hosted by the same stratigraphic unit. We use a combination of whole-rock geochemistry, short wavelength infrared (SWIR) spectrometry, laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) analyses and compiled historic whole-rock geochemical data to develop district-scale vectors towards VHMS mineralisation.Strongly sericite and K-feldspar altered rocks concentrate along a linear trend from Hellyer, through Que River, to Mount Charter. Ishikawa alteration index values and whole-rock major and trace element concentrations provide exploration vectors towards mineralisation on a regional scale as significant enrichment and depletion trends. On a deposit scale, composition variations in white mica (sericite alteration), chlorite and K-feldspar are observed and reflected in whole-rock geochemical variations. Regional SWIR data from drill core support the prevalence of phengitic mica and high-Mg chlorite within footwall alteration halos and highlight the main upflow zones of hydrothermal fluids in the VHMS district. The combined use of regional whole-rock geochemistry, SWIR and mineral chemistry is an effective way to highlight prospective areas for VHMS mineralisation in a mature exploration province.CITATION:Wu, S, Gemmell, J B, McNeill, A W and Richardson, S M, 2015. Exploration implications from variations in whole-rock and mineral chemistry around the volcanic-hosted massive sulfide deposits of the Que-Hellyer volcanics, Tasmania, Australia , in Proceedings PACRIM 2015 Congress, pp 85–90 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Quin Dennis

Process Optimization ?What is it really? It is NOT ?a larger fan to increase draft through a process ?a larger pump on a wet circuit ?a wider conveyor belt for solid materials ?a larger feed elevator into or out of a process These relieve individual constraints ??bottlenecks??and allow operation to the next constraint in the process ?It is also NOT about automating the operator ?which captures consistency but is not continuous optimization

Nov 1, 2011

By R. Biss

"Niobium or columbium, as usually called in North America is becoming a more and more important metal in the industrial world because of its attractive properties.Eventhough discovered in the early nineteenth century, it was not until the 1930's that its use became more widespread. The discovery of large commercial deposits in the late 1950's and the demand of industry for steel with high strength and toughness further promoted its use. To assure its adequate supply new or-e processinr technologies had to be developed. So, beside the traditional gravity concentration, the flotation process was employed for the partial upgrading of pyrochlore concentrate at S8ve (Norway) plant in 1953. The flotation process was equally used at St-Lawrence Columbium plant in the province of Quebec, Canada. The new plants at Araxa and Catalao in Brazil and at St-Honore, Canada, which supply almost of all niobium used today in the non-Communist world, also adopted the flotation process. The processes using long chain aliphatic rnonoarnines, diamines or sulfonates as collectors proved to be difficult especially on weathered types of ores or on those having a substantial content of silicate gangue minerals. They almost completely failed in case of alkaline intrusive rocks as syenites, nepheline syenite, ijolites and pyroxenites, composed almost entirely of silicate minerals. A lot of effort was devoted all around the world on research of new, more efficient flotation processes. So in 1982, Les Services T.M.G. Inc. (Niobec), sole producer of pyrochlore concentrate in North America, developed the direct pyrochlore flotation process from carbonatites. In 1983, at about the same time, the Quebec Department of Natural Resources Laboratories and Les Services T.M.G. Inc. announced a successful recovery of niobium Minera1s from a low grade nenheline syenite ore."

Jan 1, 1984

By C. K. Kocsis, S. Hardcastle

Mine ventilation, requires electricity to operate the fans and fossil fuel for heating. Typically, this accounts for approximately 40% of the overall underground energy consumption. This is considerable, and one of the major causes of this expense is that most mine ventilation systems are designed for the "worst-case-scenario" with respect to ventilation demand, which is commonly dictated by diesel equipment usage. Once designed, mines tend to operate their ventilation system at this peak level despite their exceeding day-to-day development and production needs due to lack of appropriate ventilation controls. In underground metal mines, TeleminingTM, which includes the tele-remote operation of mobile development and production equipment from surface, will change the mine design criteria including its support infrastructure such as the ventilation system. With the removal of machine operators to surface control rooms, conventional ventilation systems designed to dilute and remove pollutants can become redundant. Depending on the ultimate need for ventilation, its cost in automated mines with tele-remote equipment operated from surface will be lower than the cost of ventilation in conventional mines. These cost savings, which could be significant, would not only come from the ability to reduce the amount of ventilation in the mine, but also through the capacity to automate its distribution. This paper provides an indication of the new airflow requirements in stopes and dead-end developments for the tele-remote and automated mining processes based on climatic modelling. Furthermore, this paper makes a cost benefit analysis by comparing the ventilation system operating cost of a conventional underground metal mine based on the mobile diesel powered equipment design criteria with the newly redesigned ventilation system operating cost of an automated mine based on the "heat management" design criteria.

Jan 1, 2002

By Damian Connelly

The metallurgical heart of the majority of copper oxide processes is the heap leaching operation. Fresh low grade sulfide ores is a far greater challenge.The success of this unit operation is so important that operators need to understand the ramifications of their decisions or non-decisions and how they could affect the downstream processing. Heap leaching is an operation that can be described as a scientific art whereby principles of science can be used to guide experienced personnel in attaining their goals. Recent advances have been made based on better understanding the ore characteristics. The success of a heap leach operation, or otherwise, is dependent upon a number of factors, notably: The type of ore to be treated The extent of testwork completed to define the process The interpretation of the testwork results Ore preparation prior to stacking Agglomeration and curing requirements Other issues are: Compliance with the ’smaller’ requirements of environmental authorities Adequate and timely drainage of solution from the base of a leaching lift The degree of saturation in the pads Heap porosity – coarser or finer ore, which is better? Higher or lower irrigation rates – which would produce a better result? Laying out irrigation pipework for ease of operation and maintenance The addition of water, raffinate during agglomeration where needed The heap leaching of sulfide ores, including chalcopyrite, via enhanced bacterial leaching is discussed. INTRODUCTION Over the last twenty years, production of extremely pure copper from solvent extraction and electrowinning (SX/EW) has become more common in a market of real declining prices for copper metal. This paper touches on a number of heap leach operations and experiences. These projects were subjected to extensive engineering design and resulted in low capital cost, efficient operations with a number of lessons learned. The key to these operations was the performance of the heaps and associated fluid collection systems rather than the plants themselves.

Jan 1, 2019

By Vítor Covre Evangelista da Silva

Esta proposta objetivou desenvolver uma análise teórico/experimental da influência de 2% Ag (em peso) em uma liga de solda Sn-40%Bi solidificada unidirecionalmente em regime transitório de fluxo de calor. Correlações experimentais entre os parâmetros térmicos de solidificação como velocidade de deslocamento da isoterma liquidus - VL, taxa de resfriamento - ?L e parâmetros microestruturais como espaçamentos dendríticos secundários – l2 foram determinados. A caracterização microestrutural foi realizada por meio de microscopia ótica e eletrônica, difração de raios-x, além de fluorescência de raios-x para obtenção dos perfis de macrossegregação dos solutos (Bi, Ag). Para determinação do perfil de dureza foram realizados ensaios de dureza Vickers. As microestruturas brutas de fusão da liga Sn-40%Bi-2%Ag são compostas de dendritas ricas em Sn decoradas com partículas de Bi circundadas por uma mistura eutética (Sn+Bi) e partículas primárias de Ag3Sn. Os parâmetros térmicos decresceram com aumento da camada solidificada, permitindo uma ampla variação: ?L ? 0,1 a 10,0°C/s, VL ? 0,2 a 0,9mm/s e GL ? 0,4 a 11,0°C/mm. O teor de bismuto não variou significativamente, ao passo que a prata variou de forma efetiva, concentrando-se no início do lingote (até próximo de 35mm). O surgimento de braços dendríticos terciários em 15mm conteve a diminuição da microdureza Vickers, esperada para as posições mais afastadas da interface metal/molde.

Aug 16, 2017

By H. Gumede

The occurrence of fracturing due to high stress levels is a major factor in hangingwall stability in deep level gold mine stopes. However, rock falls cannot be the result of these fractures alone. Rock falls can result only from the occurrence of unstable rock blocks defined by the interaction of the stress induced fractures and naturally occurring geological planes of weakness. These planes include bedding planes and joint set planes. However, there is a general lack of information on the characteristics of these planes (orientations, spacings and lengths)?it does not appear that any such systematic and quantified information, if collected, has been published. To remedy this situation to some extent, joint mapping exercises have been carried out in several geological environments in two gold mines. The data collected on joint geometry included orientation, spacing and length, and this information is included in the paper. In addition, the paper describes the use of the data collected to evaluate the potential for rock falls and the probability of failure of stope support

Jan 1, 2007

By B. W. Madsen

To help maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines developed a mathematical model that describes acidic ferric sulfate leaching of copper from sulfide ores. The leaching model can aid in maximizing minerals and metals recovery from primary sources by giving operators and management a better understanding of the copper leaching process. This will aid in improving dump leaching operations. The model is based on a steady-state approximation of the continuity equation for diffusion of ferric ions in the rock pores and the intrinsic leaching kinetics of the various sulfide mineral particles. Ore characteristics included in the model were ore particle-size distribution, particle shape, grade, mineral content, mineral particle size, porosity, and tortuosity. The continuity equation was used with ferric ion concentration gradients and a fixed value for the diffusion coefficient. Except for effective diffusivity, each of these factors was either measured experimentally or estimated from theoretical considerations. The effective diffusivities were determined by fitting calculated leaching curves with experimental leaching data. Vertical variations in leach solution composition and temperature within a dump are not considered in this model. The model accurately predicted copper extractions for several large-scale tests during nearly 500 days of leaching.

Jan 1, 1981

By G Metzner, R Rodriguez, C Savage

OK Tedi Mining Ltd. (OTML) is in the process of optimising the concentrator performance. One aspect that has been recently implemented is an upgrade of the existing expert control philosophy on the grinding circuit and this will be the topic of this paper. Ore grinding in SAG mills is a multi-input multi-output (MIMO) process subject to several disturbances, most typical being quick acting disturbances such as changes in ore characteristics like hardness and particle size and slow acting disturbances such as ball charge variations and liner wear. The OTML SAG mills treat ore from diverse ore bodies and receive fresh feed subject to large changes in particle size. These circumstances make these mills particularly challenging to control. In this paper, a comparative analysis is presented between the performance of the OTML SAG mill #2 before and after the commissioning of a hybrid control strategy. The strategy uses Expert Knowledge combined with advanced disturbance rejection to reduce the variability of the main process variables, especially pressure and power. It further optimises the overall operation by driving the SAG mill #2 against process constraints (e.g. high power, high motor temperature and high scats recycle rate) and maintaining the operation at or near this point. This strategy is implemented by a combination of the manipulated variables (i.e. fresh feed tonnage and % solids) at any given time.The paper will present trends and a statistical analysis of the comparative results of the mill operation over a period of months, showing a 30% reduction in mill power / pressure variability and a 12% improvement in average power drawn. An increase in throughput was also observed, but cannot be conclusively attributed to the change in mill control due to other changes that were made to the SAG mill #2 during the period of comparison. An additional benefit includes better acceptance from the operators with improved consistency of the SAG mill #2 operation across shifts.The paper will also discuss further improvements envisaged in the continued optimisation of the grinding control circuit.CITATION:Savage, C, Rodriguez, R and Metzner, G, 2013. Hybrid process control strategy for the Ok Tedi Mining Ltd semi-autogenous grinding mill #2 - A comparative analysis, in Proceedings MetPlant 2013 , pp 202-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By R. L. Fullman, J. W. Cahn

A method is derived for obtaining the distribution of sphere diameters and plate thicknesses (or pearlite spacings) from size distribution functions obtained along randomly oriented lines. The method described offers several advantages over existing methods. IT is often of interest to measure not only the average particle size but also the distribution in sizes of particles dispersed in an opaque material, such as an alloy. Particles of a single size will exhibit a range of apparent sizes on the plane of polish. If the sample contains a distribution of particle sizes, the distribution of observed sizes on the plane of polish is related to the distribution of actual particle sizes by an integral equation, For example, a distribution of sphere sizes, N(r),

Jan 1, 1957

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

By J. H. Daniel

This report, summarizing the results of two studies sponsored by the Bureau of Mines, presents information on the types of mobile machines used in surface coal mines in the United States, and the amount of noise to which miners are exposed. Data consist of a calculated value of the probability of noise overexposure caused by specific equipment. These data are extrapolated to estimate the number of overexposed operators. Bulldozers were identified as the major contributors to noise overexposure, and the report presents results of a Bureau-funded program on the feasibility of providing retrofit noise control on bulldozers.

Jan 1, 1980

By William P. Blake

The ancient city of Guanajuato, the capital of the State of that name, has been built up and sustained chiefly by the milling industry based upon the veins of the Veta Madre and La Luz. It is distant about twelve hours, by rail, from the City of Mexico. Its elevation above the sea is about 6300 ft., and it has a salubrious climate. The population, at the date of my visit in 1891, was estimated at from 80,000 to 100,000 persons. The place is justly celebrated for the antiquity, depth and extent of the mines, the magnitude of the deep shafts, and the enormous total yield of the district in silver and gold, which is comparable with that of the Comstock Lode in the United States. Several important public institutions are located at this center. The State office for the records of claims and of the statistics of mining and production is known as the Deputacion de Mineria. The Mining College, with its fine collection of ores and minerals from the mines of the region, is highly interesting to mineralogists. A mint for the coinage of silver, but not of gold, coins from four to twelve millions of' silver dollars annually. The silver received at the mint is melted in an open-hearth furnace, and is ladled out and cast into long and thin bars, which are rolled down to the proper thickness for the blanks. The bars contain some gold which is not parted. There is an export of dore bars to Germany, amounting in value to from $1,000,000 to $1,500,000 annually. There were, in 1891, upwards of forty reduction-works in and about the city where the silver ores were treated, chiefly by the ancient patio method. In these works were 65 Chilean mills, 301 arrastres of large size, and 936 of smaller dimensions. There were 36 steam engines, but mule-power was generally used at the ar-

Jan 1, 1902

By S. Sunkavalli

Acid rock drainage (ARD) is produced when sulfides are exposed to oxygen and water. Oxidation reactions typically result in a depression of pH and leaching of solutes and metals. Many oxidation models have been developed based on oxygen diffusion, but in environments with high permeability, other transport processes (i.e., convection and advection) can play an important role. Multiple sulfide mineral phases with differing oxidation rates should also be incorporated. WROC, a finite-difference model, was developed to account for these factors in predicting ARD. The program includes sulfide mineral oxidation using a shrinking core mechanism, heat transfer by conduction, heat of reaction, and oxygen transport by diffusion and advection. The model was validated using data from the literature. After validation, the WROC model was used to simulate several different waste rock scenarios including different forms of sulfide mineralization and the effect of implementing a waste rock cover. The results demonstrate that including specific sulfide mineral phases can have a significant effect on oxidation and that implementation of a cover can also aid in reducing waste rock oxidation. Key words: Arsenic sulfides, oxidation, shrinking core, waste rock, oxygen transport

Feb 27, 2013