Search Documents

By C. F. Barter, H. G. Kreis, D. S. Weber

Before and during in situ mining at the Santa Cruz In Situ Copper Mining Research Project test site, hydraulic testing was conducted at injection and recovery test wells to characterize patterns of fluid movement in the 5-spot well field. Testing included borehole spinner flow meter surveys, single-well and multiple-well injection and recovery tests, straddle packer injection tests, and bromide pulse tracer tests. Results of hydraulic testing for determination of fluid flow regimes were used to modify well and mining zone hydraulics for the purpose of increasing fluid migration in flow pathways of the mining zone with higher copper grade.

Jan 1, 2000

Suggestions have been made at various times that there may be a recurrence of lodes similar to those at Kalgoorlie in the country to the south of the Golden Mile, but, so far as is known, there has been no geological evidence to support these suggestions apart from the possible extension of the younger quartz-dolerite greenstone in this direction.Geological mapping carried out by the writer in the Coolgardie district in 1946, provided some additional geological evidence to support this claim, and the ideas then held have since been expanded and are now considered to be sufficiently advanced to present them as concrete suggestions. As will be seen from the following pages, the critical area for lode prospecting is Hannan's Lake, where the basement rocks may include younger quartz dolerite greenstone, which, although perhaps distributed over a smaller area than at Kalgoorlie, could, on structural grounds, have a similar fracture system and similar ore deposition.There is little need to stress the importance discoveries in this area would have in prolonging the life of the field, and stimulating the post-war gold mining revival.Previous Work: Only the publications having a direct bearing on the preparation of this paper are given in the list of selected references, but the writer is very conscious of the fact that much other geological work has been carried out in the Kalgoorlie district since its discovery, by the W.A. Department of Mines, by mining companies, and others, all of which has contributed to the present knowledge of the field, and acknowledgment of the value of this work is given herewith. In presenting the suggestions in this paper a broad structural control of ore deposition is assumed, but this has already been established in other parts of the goldfields of Western Australia, including adjacent areas. In the early nineteen thirties, the Western Mining Corporation commenced work on the basis that there was a close relationship between geological structure and auriferous ore deposition, and a similar approach was first made by the Geological Survey of Western Australia in the South Yilgarn in 1935. These ideas were further developed during later surveys, particularly in the North Yilgarn and the Mount Margaret Goldfield.During the Coolgardie Survey in 1946, broad structural mapping was done in greater detail than before, and the structural ideas were implemented and further developed, leading to some success.Other work to which particular acknowledgment is given is that of Stiltwell, Gustafson and Miller, Forman, Prider and Finucane, at Kalgoorlie, and that of Honman in the Kalgoorlie-Coolgardie district, references to which are given at the end of this paper.Valuable constructive criticism of this paper has been given by Professor E. de C. Clarke and Dr. R. T. Prider, of the University of Western Australia.

Jan 1, 1950

By S. S. Peng, C. T. Holland

Mountain Top Removal (MTR) mining started in West Virginia nearly thirty years ago. This surface mining method can extract multiple coal seams as thin as a few inches thick with total recovery and minimum rock dilution in very steep mountainous terrain. It is highly efficient even if coal seams are in close proximity and small in aerial extent. Consequently, MTR has been widely used in the Central Appalachian Coalfield (mainly Kentucky, Tennessee, Virginia and West Virginia) for the past thirty years with great success. In that respect, there has been no demand for research and little scientific research has been performed to investigate its impacts on the surroundings in the history of MTR mining. However, in the past two years the debate over the MTR mining has grown quickly and in times become very intensely. This paper describes chronologically the issues raised by various parties, legal actions, its impacts on mining permit application and research projects developed to address the issues.

Jan 1, 2000

By William A. Enrico

Umicore acquired the Pirdop Smelter in a privatization offering by the Bulgarian government in September 1997. Since that time, an investment program has been conducted to increase capacity to 225 000 tons per year of anode copper, while improving the environmental performance to meet Bulgarian and European standards. A significant part of this investment program involved reconstruction of the three Peirce-Smith converters and the associated gas handling system. During the period June, 2000 through April, 2002, converter capacity was increased, the existing water-cooled hoods were replaced, the waste heat boiler was replaced by two evaporative coolers, the dry ESP's were rebuilt and extended, and a Converter Control System (CCS) installed. From 2002 until the present, a continuous improvement of operating and environmental performance has been achieved. This paper will describe the converter reconstruction project, the operational, maintenance, and environmental improvements achieved since then and additional projects presently under consideration.

Jan 1, 2005

By D A. McCallum

With depth, many gold ores become sulfidic with minerals such as pyrite, pyrrhotite and arsenopyrite becoming prevalent. In addition, many underground gold mines use tailings backfill to bind and store the waste. In these cases, acid mine drainage (AMD) can become an issue. One approach to the control of AMD is desulfurisation whereby the sulfide minerals are removed prior to disposal. Four sulfide tailings samples, representing different ore types and gold and base metal operations, were selected for assessment and testing using simple physical beneficiation techniques. The aim was to determine the extent to which mineral processing methods were suitable for separating sulfides from non-sulfides and for extracting potentially marketable by-products from the tailings. In order to streamline the testing procedure a simple diagnostic separation technique was developed to enable quick screening of bulk sulfide tailings for suitability for reprocessing. The testing procedure involved detailed characterisation and a sequential set of testing regimes based on simple unit processes including water washing, classification, gravity concentration, magnetic separation and bulk flotation. The preliminary test results indicate each unit process can play an important part in producing effective sulfide/non-sulfide separations and in generating useful by-products from the tailings. Potential valuable products identified include coarse, benign silica sands, bulk iron sulfide products rich in pyrite and/or pyrrhotite, high-grade iron products (magnetite) low in silica, low-volume bulk sulfide concentrates and low-grade molybdenite and talc products. The work presented shows how sulfide tailings can be viewed as a resource rather than a waste stream, and identifies a pathway for developing a more sustainable approach to the environmental management of sulfide tailings for the future.

Jan 1, 2007

Support design in jointed or blocky rock masses is often approached by the use of either 'rules of thumb', rock mass classification systems such as the Q-system (Barton, Lien and Lunde, 1974) or RMR (Bieniawski, 1973) or conventional wedge analysis. Generally, this requires that a number of key simplifying assumptions are made and the support system is designed to cater for either a mean, most likely, or worst case scenario depending on the risk tolerance. The design block size is often a major uncertainty and often a worst case block size based on excavation span is used. Thompson and Windsor (2007) state that it is inappropriate to base support designs on the excavation size as these size blocks rarely occur if discontinuity trace lengths are considered. Probabilistic keyblock methods can be used to determine the most likely design block sizes. A methodology is presented whereby JBlock software (Estherhuizen, 1996) is used to estimate potential block sizes as part of the support design process. Using information such as the spacing, orientation and length of discontinuities, it is possible to simulate blocks in the walls of an excavation (Esterhuizen and Streuders, 1998). Keyblock analysis methods (Goodman and Shi, 1985) are used to evaluate whether blocks are removable and whether the chosen support will be sufficient to ensure stability. Data from two mines is used to demonstrate how probabilistic keyblock analyses can be used in support design. Discontinuity data was used to generate 10 000 removable blocks and the design block size statistics were determined. For one mine this information was used to scale blocks in a conventional. Unwedge analysis whilst for the other mine, the point estimate method (Harr, 1987) was applied. The choice of appropriate design acceptance criteria in terms of factor of safety and probability of failure is also considered.

Nov 25, 2010

THE object of the air-tight stopping is either to prevent a current of fresh air from getting into the fire area, or to prevent an escape of fumes and gases from the fire area into the workings of the mine. In the former case all is "plain sailing," but in the latter case there are certain difficulties to be overcome.In the Broken Hill Proprietary mine there were two styles of stopping used during the last fire-brick and bag and the following were the chief points that determined the use of one in preference to the other:-If the required stopping were to be more or less permanent, bricks were used, also if the area to be blocked were large-bricks being so much lighter and easier to handle than bags filled with -skimps. If, however, the air contained much gas, a bag stopping was put up. Great difficulty was experienced in getting essentially surface men, such as bricklayers, to work where there was the; slightest trace of gas; miners, however, would willingly do the work, and a bag stopping could be built without skilled labour.In old drives and gangways, where there was the liability of settlement, the bag stoppings were preferable to brick. The slightest movement around the sides or foundations of the latter would cause cracks, thus rendering the brick stopping useless;whereas, in the former, there was a certain amount of elasticity.

Jan 1, 1909

Probably no other country or coutinent has so many rich deposits of various different minerals as Australia. Long ago in the days of my boyhood in the old land the marvellous discoveries of high percentage copper at Burra Burra, Peak Downs, Yudanamutana, and other mines, was one of the principal themes of conversation in mining circles whilst the specimens of malachite, azurite, etc, brought home by returning miners were the admiration of my boyish eyes.Later on the WalIaroo and Moonta mines still further helped to heighten the reputation of Australia as a copper-producing country. During the 21 years that the writer has been resident in the Australian colonies, other mineral deposits have sprung into prominence, and with a Mount Bischoff for tin, a Broken Hill for silver and lead, and a Mount Morgan for gold, Australia can now boast that it has had within its borders the leading mines of the world, in four different minerals, and still at least maintains that pre-eminence in gold, silver and tin. To the miner from the old land, Australian mining is at first a revelation and a wonder. In very many instances he looks in vain for the regular strike and dip of the veins he has been accustomed to'Smooth hanging and foot alls are often wanting. 'Huge irregular deposits, like those mentioned above, viz., Burra Burra, Mount Bischoff, Broken Hill, and Mount Morgan, are mysteries that will take time to fathom-if, indeed, they are ever thoroughly understood and in many a smaller deposit there is much to interest alike the professor in the college and the miner in the mine.

By E. M. Cohn

The literature dealing with the electrical conductivity of solid dielectrics, including all its aspects and its relationships to other physical properties of these materials, is extensive and scattered in many books, phamphlets, and periodicals. It is believed that most of the important contributions to this field up to October 1943 have been listed and abstracted in this circular. Also included are some general references on static electricity. Methods of removing static charges are described; methods of and conditions for measurements of resistivity are discussed; equations for the calculation of resistivity are given; and methods of resistance measurements in Situ are reviewed. Data on the variations of resistivity with changing conditions as well as explanations for them have been collected, and three tables showing the resistivity of various dielectrics at different humidities are included. The appendix contains a short development of the mathematical formulation of the charging and discharging currents due to interfacial polarisation. INTRODUCTION Methods for Removing Static Electricity Of the various means employed for preventing or removing accumulations of static electricity in industrial processes, grounding is the most common and most generally effective. It is a precaution readily applied to stationary machines anti may often be utilized to good advantage to rid persons and portable equipment of an acquired charge. There are many situations, however, in which direct low-resistance grounding cannot be used, either because the charged bodies are insulators or are inaccessible, or because contact to a ground lead might give rise to a hazardous spark. If the charged body is a conductor, contact made to a neighboring conductor, even though the latter be insulated from ground and of relatively small capacitance, may also result in the occurrence of an incendive spark. In such instances, static electricity can sometimes be removed most satisfactorily by means of strong atmospheric ionization produced by radioactive material, X-rays, ultraviolet light, or A. C. high-voltage brush discharge. Where no danger exists from flammable

Jan 1, 1944

By Wayne Trudel, Eric Saderhold, Lloyd McEvers, Lori Clarke, Charles Lynn Bolin, Leroy Schutz

Editor’s note: This is the second part of a two-part series on how mine geologists added about 141t (4.53 million oz) at Newmont Mining’s gold operations in Nevada during 2003. Part one (ME, July2004, pp. 19-26) showed how cross-functional teamwork among mine geologists, engineers, metallurgists and operators added $65 million in revenues at Newmont’s Gold Quarry Mine. Part two deals with how this same cross-functional team added about 25.8 t (830,000 oz) of gold reserves and two years of life at the company’s LoneTree Mine. This was done through improved reconciliation methods, pit optimization designs and updated geotechnical parameters. Part two also discusses how Newmont’s Nevada mine personnel added about 62.2 t (2 million oz) of gold reserves at its Twin Creeks Mine, extending the mine’s life by several years. The Lone Tree Mine is a sediment-hosted, micron gold deposit. It is dominantly situated in the Golconda thrust footwall. The north-south trending Wayne Zone fault controls the highest-grade ores and

Jan 1, 2004

By E Portes, G Noble, J Roberto, A Stabile

Iron ore beneficiation plants are facing economic pressures to treat more challenging ore types, improve efficiency and improve product quality. Better control and stability of the plant process in the face of increasing feed ore variability has been a goal for many of the operations facing these challenges.Prompt gamma neutron activation analysis (PGNAA) technology has proven to be a successful measurement technique within an iron ore beneficiation plant. PGNAA was first developed in the early 1980s for the measurement of the elemental composition of bulk materials. Today, PGNAA technology is applied for elemental analysis within the iron ore industry on both bulk materials and slurries.Traditional composite sampling throughout the wet iron ore beneficiation process provides a delayed measurement of average properties but does not capture the true variability of the process in real-time. As such this is a limiting factor towards stabilisation and optimisation of the process. A PGNAA analyser provides real-time slurry elemental analysis of feed, concentrate and tails streams within the processing plant. The analytical data from the analyser can be exploited with a control strategy to correct and stabilise the plant on a much shorter time scale, delivering significant economic benefits and greater operational flexibility. The economic benefits include more stable product quality and a reduction in composite sampling and laboratory costs.Some example results will be presented from the Vale Vargem Grande iron ore beneficiation plants, which are utilising a six stream multiplexed Thermo Scientific PGNAA Slurry Analyser.CITATION:Noble, G, Stabile, A, Portes, E and Roberto, J, 2017. Real-time slurry elemental analyser for iron ore beneficiation plant control, in Proceedings Iron Ore 2017, pp 481–486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Nikhil Dhawan, Shrey Agrawal, Veeranjaneyulu Rayapudi

India’s steel vision of 2030 requires a huge amount of quality iron ore. The utilization of low-grade iron ores such as banded iron ores will play an important role to achieve the same production. The absence of alumina impurities in the banded hematite jasper (BHJ) ore provides it an edge over other low-grade iron ores. The conventional beneficiation techniques such as magnetic separation and washing were found to be ineffective to produce suitable feed (Fe ~ 60%) for the blast furnace. It was found that microwave exposure provides significant enrichment to the low-grade iron ore and can be used as a pretreatment step in the beneficiation of similar low-grade iron ores. The above study reveals that hematite phase is susceptible to microwave exposure which enhances the separation of iron values from impurities. Under optimum conditions, an iron-enriched concentrate with 61% Fe, 85% Fe recovery at 50% yield can be achieved from BHJ feed ~ 38% Fe. The pretreatment process for BHJ beneficiation includes only microwave exposure without any chemical additive and may prove economical and industrially feasible.

By Reginald Dias

Mining equipment life may be extended through preventive maintenance and the proper application of quality lubricants. There are several practices mine operators should consider implementing to preserve their equipment. An exercise in review — Begin by reviewing original equipment manufacturer (OEM) recommendations regarding servicing and maintenance intervals for each part of the equipment, especially the engine. And the verdict is — If the manufacturer’s recommendations have been followed, good. If not, owners/operators should begin periodic service work on equipment, to help minimize equipment downtime and extend engine life.

Jan 1, 2004

Possibilities and Working of the Specific Agglomeration of Fibrous Materials and Residues Plant based fibrous materials are becoming of increasing interest in a multitude of industrial applications. Main advantages are the specific lower energy demand and virtually closed CO2 cycle, excellent mechanical properties based on low density as well as a high level of recyclables. In contrast, processing and handling of such materials is associated with a number of challenges. These challenges are mainly related to specific morphological characteristics in correlation to fibre length and structure (branching and splices). Specific problems in further processing steps including transport, dosage or storage for natural fibre compounding, result from form-locking bonds leading to burling, clusters or plaits. Technologies of fibre processing are well known, but other than textile based technologies they generally result in intermediate goods which do not allow direct industrial application. The investigation to be presented is based on results of recent research activities and shows two possible technical solutions of innovative fibre agglomeration procedures. These methods allow the conversion of middle to long fibres into a form, which eases further processing and dosage significantly and therefore allows free flowing too. The procedures are based on the working principles of rolling and winding technology. Within the work, both of the patented methods and their respected lab-scaled devices will be described. Further, results will be shown for an up-scaled rolling agglomeration unit applying the developed principle and consisting of multiple process zones. Possible variations of the resulting product characteristics and the impact of different process parameters will be discussed based on the trials with natural fibre (hemp and flax) agglomeration. As a main outcome of the research, product qualities can be supplied according to the requirements of the specific application in correlation to agglomerate strength, porosity or form. In conclusion, recent developments for specific methods of characterization will be depicted.

Sep 13, 2010

By Fredrick Fränding

In mining and quarrying operations, electric motors can fail for a variety of reasons. Some failures are directly linked to demanding production requirements and contaminant-laden environments and, consequently, are difficult to prevent. A sizeable number, however, are caused by ?offline? factors that have nothing to do with production. These include inadequate or substandard motor repair practices and improper motor shipping, storage and installation. The fact that failures are at times attributable to repair- or rebuild-related errors and problems raises the stakes when selecting an electric motor repair provider. Teaming with high-quality electric motor shops can help a company reduce failures due to offline factors, improving motor reliability and cutting downtime costs. Regardless of location or annual revenues, the best motor shops have similar business cultures and share many of the same characteristics.

Jan 1, 2009

By Michael L. Jones

Outline ?Background ?Identify and quantify CO2 sources ?Consider options for CO2 separation and capture ?Review options for sequestration/reuse ?Determine best option for managing CO2

Jan 1, 2008

By J. A. Delgadillo

Computer simulation and mineral modeling was applied to the optimization of a grinding circuit in a plant processing 256 t/h magnetite. These tools were used to develop a grinding and classification configuration to decrease the grade of silica in the magnetite concentrate, which is produced by the plant. Empirical grinding and classification models were finely tuned using plant experimental data. The JKSimMetTM 5.0 software was used to simulate the grinding and classification units. By applying changes in the original circuit, a throughput increment of 100% was achieved with an important reduction in the energy consumption. The silica content in the magnetite concentrate can be decreased by regrinding the coarse fraction of fine screens into a separate ultrafine grinding unit instead of returning this flow to the ball grinding mills.

Jan 1, 2008

The Resource Management Act 1991 (RMA) and the Crown Minerals Act 1991 (CMA) both came into force on 1 October 1991. The purpose behind RMA was to integrate the existing laws dealing with town and country planning, land subdivision, water and soil, minerals and energy resources, coastal management, air pollution and noise control into one omnibus Act. Originally, there was a section in RMA dealing with minerals. However, this section was taken out of RMA and a companion piece of legislation - namely CMA - was passed with RMA.

Jan 1, 1994

By V. Coetzee

Keywords: Pyrometallurgy, furnace, PGM, platinum, nickel, copper, electric smelting, six-in-line, Peirce-Smith, Impala Platinum In 1992, a paper was compiled highlighting a common-sense approach to electric smelting at Impala Platinum. Since then, the smelter complex has undergone considerable changes. Mineral economics, UG2 exploitation, and changing environmental legislation have enforced numerous process upgrades, yet a common-sense approach has always been adopted. This document details the major changes in the smelter complex at Mineral Processes (Minpro) over the past 15 years, and provides the rationale for the changes.

Jan 1, 2006

B. P. Thomson (South Aust. Dept. of Mines): Dr. A. B. Edwards presents in the published discussion on the above paper, his interpretation of the dolerite dyke-lode relationship as a major objection to the syngenetic origin for Broken Hill ore bodies to which Mr. Condon subscribes.Dr. Edwards claims that the dyke-lode relationships indicate clearly that the Broken Hill orebody was formed after the folding and regional metamorphism of the Willyama Series. Field evidence compels m:e to join with H. F. King (1958), in finding this conclusion unacceptable-as follows:(1) Broken Hill type mineralization, as defined by King and Thomson (1953), is clearly confined by the regional sillimanite isograd and does not extend into the lower temperature almandine and biotite zones as does the Thackaringa type mineralization.(2) In the Corruga area the writer has mapped a dolerite dyke apparently cutting a conformable quartz gahnite lode of the Broken Hill type (see Edwards 1958, p. 12).(3) At the Champion mine a similar lode is cut by a fine grained granite dyke.An alternative history of the dolerite dykes to that given by Stillwell & Edwards (1956, p. 26) appears possible. It has been suggested by the writer in an unpublished thesis, (Thomson 1955, p. 30), that the pyroxenite and serpentine plugs and dolerite dykes are rheomorphic end-products of a complex regional metamorphic and metasomatic process involving the formation of amphibolite and pegmatite. The analogy in composition between the dolerite and normal amphibolite is close (see Edwards 1958, Fig. 1, p. 22).

Jan 1, 1959