Search Documents

By J J. J Chen, J C. Zhao

A water/air model was developed to simulate the refining of molten aluminium by the sparging of gas through an impeller. The optimal gas dispersion depends upon selecting the correct gas rate for a given impeller rotational velocity to prevent flooding or channelling. Correlations illustrating this flooding behaviour exist for standard impellers within standard tank geometries. However the validity of these correlations has not been substantiated for gas dispersion in high temperature molten metals with non-standard tank and impeller dimensions. Metal refining is most efficient when fine bubbles are generated and uniformly distributed within the treatment tank. The application of some measuring technique able to detect this distribution within a non transparent operating treatment tank would be invaluable, enabling the optimisation of gas flow and impeller speed.   A technique has been developed to measure the pressure fluctuation levels at specific points in the water model. Comparison of these pressure fluctuation data with photographic evidence obtained in the water model suggests that the flow regime in the metal treatment unit may be determined using this technique.

Jan 1, 1995

By D. Lelinski, R. Bokotko, J. D. Miller, J. Hupka

Air-sparged hydrocyclone (ASH) flotation is a new, promising technology, and, since its conception, numerous applications have been successfully tested. Nevertheless, research and development efforts have continued to improve the technology with respect to operating conditions and design considerations. Results, from experimental studies on bubble generation in the ASH system are presented in this paper. Bubble size distributions generated during ASH operation were determined using a high-speed photographic technique. The influence of many factors, including surfactant concentration, water flow rate, and porous-tube pore size have been studied. Test results indicate that these process variables have a profound effect on the bubble size distribution. With an increase in surfactant concentration or water flow rate (shear field), the bubble size distributions become narrower and shift toward smaller average bubble diameters. However, the influence of pore size is more complicated. Depending on the experimental conditions, the average bubble size was found to range from about 100 to 300 µm in diameter.

Jan 1, 1997

By D. Lelinski

Air-sparged hydrocyclone (ASH) flotation is one of the new promising technologies. Numerous applications have been successfully tested since its conception; nevertheless, research and development efforts have continued to provide for further improvements with respect to operating conditions and design considerations. Results from experimental studies on bubbles generation in the ASH system are presented in this paper. Bubble size distributions generated during ASH operation have been determined using a high-speed photographic technique. The influence of many factors including surfactant concentration, water flowrate, and porous tube pore size has been studied. Test results indicate that these process variables have a profound effect on the bubble size distribution. With an increase in surfactant concentration or water flowrate (shear field) the bubble size distributions become narrower and shift toward smaller average bubble diameters. However, the influence of pore size is more complicated. Depending on the experimental conditions the average bubble size was found to range from about 100 to 300 microns in diameter.

Jan 1, 1995

By David Seaman, J-P Franzidis, Emmy Manlapig

"A new device has been developed to directly measure the bubble loading of particle-bubble aggregates in industrial flotation machines, both mechanical flotation cells as well as flotation column cells. The bubble loading of aggregates allows for in-depth analysis of the operating performance of a flotation machine in terms of both pulp/collection zone and froth zone performance. This paper presents the methodology along with an example showing the excellent reproducibility of the device and an analysis of different operating conditions of the device itself.The device has been used to investigate the froth selectivity of attached particles. Simultaneous measurements were made using a different froth recovery measurement technique in the same flotation cell. A comparison of these techniques shows that in this case, particles are selectively detached from bubbles at or near the pulp-froth interface.INTRODUCTIONA flotation cell can be considered to operate in two distinct phases or zones; namely the pulp or collection phase and the froth phase. The pulp zone is responsible for the formation of hydrophobic particle-bubble aggregates, whilst the froth phase is responsible for the separation of these aggregates from surrounding suspended hydrophobic and hydrophilic particles. Thus, the froth phase is the grade determining phase in flotation. A measurement of the bubble load (the mass of particles attached to air bubbles in units of mass/volume) will enable the analysis of the performance of both the collection zone at creating bubble-particle aggregates and also the froth zone at separating these aggregates from surrounding pulp.A measure of froth zone performance that has been used extensively in flotation research is the Froth Recovery, Rf, of a particular system. Froth recovery is defined as the mass of particles collected in the concentrate launder by true flotation as a fraction of the mass of particles entering the froth phase. The measurement of bubble load allows for this term to be calculated easily, rather than having to go through the laborious task of, for example, changing froth depths to determine this performance criterion (Contini et al., 1988; Vera et al., 1999b; Feteris et al., 1987)."

Jan 1, 2004

Bubble Load Measurements in Flotation - A Critical Review of Current Practice

Sep 13, 2010

By G M. Evans, C M. Phan

This paper presents an analysis on the dynamic adsorption of frothers and collectors onto air bubbles in flotation. The analysis was carried out using the theory on the surfactant transfer by diffusion and adsorption. The bubble size was considered when solving the diffusion equation for the dynamic surface excess. The adsorption kinetics was modelled employing the Langmuir adsorption isotherm and its extension with the inclusion of the lateral interaction of the adsorbed molecules (the Frumkin adsorption isotherm). The numerical computation was applied to solve the governing equations. The dynamic adsorption of the surfactants was measured in terms of the dynamic surface tension for sodium dodecylbenzene sulfonate (SDBS) and Dowfroth 250, using pendant bubble tensiometry. The results show that for air bubbles with diameter of the order of 1 mm, the bubble size effect on the dynamic surface tension is small and the solution of the diffusion equation for a planar gas-liquid surface can be used to describe the dynamic adsorption onto the air bubbles. The experimental data obtained with SDBS were well described by the Frumkin adsorption isotherm and the molecular diffusion. The model description for the experimental data obtained with Dowfroth 250 required the kinetic equations. The paper is relevant for further analysis of the role of the adsorbed surfactants in the particle collection.

Jan 1, 2005

By Liu Q, Siefken T. C, Misra V. N

The bubble size was measured in a laboratory flotation column. The effect of variables such as air flowrate, frother dosage and type, pulp density, particle size and water column height on the bubble size was investigated. The results show that an increase in either air flowrate or pulp density cause the bubble size to increase, while increases in water column height, frother dosage, surface tension or solid particle size cause the bubble size to reduce. Among the frother types tested, MIBC was found to be the most effective in reducing the bubble size.

Jan 1, 1992

By burgess F, Manlapig E. V, Franzidis J. P

Bubble surface area flux, a parameter which is determined by bubble size and superficial gas velocity, has been identified as a criterion for flotation scale-up from a metallurgical point of view. Investigations at Hellyer, Scuddles and Mt Isa

Jan 1, 1997

By R. Filippone, Donald Leroux, Colin Hardie, G. Leichtle, Cesar Gomez, Jim A. Finch

"Bubble surface area flux (Sb) is the surface area of bubbles per unit time per unit cross-sectional area of flotation machine. The units are: (m2 bubble surface/s)/(m2 cell) or s -1. For bubbles of mean size db (m), s b = 6-Qg/A db where Qg is the gas rate (m3/s), and A the cell cross-section (m'). This parameter is now receiving wide attention as the possible key machine variable in flotation diagnosis and modelling. The concept is described and the potential use of sb is illustrated by work on flotation columns and mechanical cells. In column flotation of recycled paper, the dependence of ink recovery on s b was the same regardless of size of column or type of sparger. In mechanical cells, it has been established that the rate constant is related to Sb independent of impeller type.The use of s b is limited by the problem of measurement, primarily that of estimating db. A prototype probe designed to estimate db (and hence sb) based on conductivity measurements is described. Exploratory work with the probe in a mechanical cell suggests the promise of making estimation of s b routine.INTRODUCTIONFlotation is the result of interaction among variables associated with the feed particles, chemistry and the machine (flotation cell). Trying to isolate the effects of each aids in process diagnosis and is at the centre of attempts to model flotation. The machine variables that have been investigated include the air flow number, the power number and specific power (Harris, 1976). None have survived as the basis for predicting flotation response perhaps because they did not include directly the properties of the bubble swarm (or dispersion). Recently, Gorain (1 997) explored the relationship between the flotation rate constant and various ""gas dispersion"" parameters notably: superficial air rate (Jg = Qg/A, where Qg is the volumetric gas rate and A is cross-sectional area of cell), bubble size (db), gas holdup (Eg, i.e., the volumetric fraction of a cell occupied by gas) and bubble surface area flux (sb = 6.Jg/db). Of them all, Gorain et al. (1997) conclude that the latter, the surface area flux, correlated best with the flotation rate constant. This concept was adopted from column flotation where it was used to estimate, among other factors, the maximum amount of gas that could be injected (Finch and Dobby), 1990). Let's start by reviewing the concept. Following that some examples of where the concept has been applied will be described to illustrate the current interest and finally we will consider how to measure the surface area flux."

Jan 1, 1999

By M Noy, P Hawkes

Improvements in the drill and blast process can impact on loader performance in a number of ways. The main effects being improved loading cycle times, less non-productive cycles such as oversize removal, clean-up and face raking and better bucket fill factors. The impact of improved loading cycle times on the overall cost and productivity of the load and haul cycle is very much dependent on the loader truck match and the management of the haul fleet. Previous work has shown that a 20 per cent improvement in dig cycle times may only lead to three per cent or less improvement in the overall productivity of the load and haul process. However, improving the mass loaded per pass by five per cent will lead to a five per cent improvement in productivity for any given haul fleet situation, assuming sufficient truck capacity. Work by Orica Explosives at Lab ChrysotileÆs Thetford Mine, Quebec, Canada showed a relationship between muckpile fragmentation and truck payload. With this in mind, work was carried out to determine the effect differing muckpile fragmentation distributions can have on excavator bucket fill factors. This work was performed in the laboratory to a 1:100 scale. Nine different distributions were used. These were characterised by the Rosin Rammler parameters, xc the characteristic size, and n, the uniformity index. The values of xc and n used were modelled on those previously measured at a Sydney quarry. For the range of distributions measured, it was found that the fill factors were lowest at a low characteristic size and a high uniformity index and highest at a high characteristic size and a low uniformity index. In other words the best fill factors were achieved with a more dispersed muckpile distribution with a larger characteristic size. The difference in fill factors was 16 per cent indicating that controlling the drill and blast process to produce a specific muckpile distribution can have a significant impact on the overall cost-efficiency and productivity of the load and haul process. Field measurement by Orica Explosives at a quarry in Canada supports this conclusion showing improvements of up to seven per cent in average bucket load by either increasing the characteristic size or decreasing the uniformity index of the muckpile.

Jan 1, 1999

At the Waikato North Head Ironsand operation, NZ Steel Mining Ltd is using a Bucket Wheel Excavator û shiftable conveyor mining system to excavate Titanomagnetite bearing sand and clay. The system utilises two Bucket Wheel Excavators with a two level shiftable bench conveyor and common trunk conveyor to deliver the material to a processing plant. The system was commissioned in November 1984 and has proved itself to be a high capacity, low cost method of excavating. Techniques of handling high sand faces have been developed and the conveyor layouts are going through a process of change to cope with the variable geo technical conditions and remain within: the characteristics of the excavators. The safety requirements for operating the system have been of a high standard and the experience has increased the confidence of the Company and the Mines Department Inspector's, for the first Bucket Wheel Excavator Mining system in New Zealand.

Jan 1, 1986

By W. L. Price

Since first introduced in the United States in 1964, rail mounted bucket wheel stacker-reclaimers have gained wide acceptance by users. The coal burning power plant group has adopted this new storage tool most quickly. The actual history is traced in this area in some detail. Installations in phosphate and steel mill ore storage and a listing of present users are included.

Jan 1, 1969

Politicians and economists talk glibly about the so-called knowledge revolution. The reality is that knowledge is fundamental to economic progress. Consequently there have been many technological revolutions. The global impacts of the invention of the steam engine and the development of the frozen meat industry are well known. Another less publicised technological advance occurred in Central Otago late in the nineteenth century. This was the adaptation of the bucketladder dredge to the mining of placer deposits. A product of over 30 years experimentation and innovation, New Zealand dredging technology was taken to the Risdon Iron and Locomotive Works, San Francisco by R H Postlethwaite, a Dunedin based mining engineer. New Zealand-style dredges built by Risdon operated successfully in California, Alaska and the Yukon. Californian engineers assimilated the best features of the New Zealand dredges with American (Bucyrus) designs to produce a standard for the worldwide placer mining industry.

Jan 1, 2003

By Frank J. Foster

This Paper will deal with Bucketwheel Suction Dredging and its particular relationship to mining applications. There will be comparisons with other methods of suction dredging and descriptions of two recent bucketwheel installations in the mining area. The Directory of World Dredging Fleets published in the `larch 1984 edition of World Dredging magazine shows that there are about 1.000 conventional Cutterhead Dredges listed throughout the world with 289 in the United States. There are 242 Bucketline Dredges listed throughout the world of which only 6 are in the United States. These figures are not completely accurate because several units are known to the author that are not on the list and, of course, there may be others.

Jan 1, 1984

Sheaves are a critical safety component in a winding system and are expected to survive such extreme loading events as rope break. Sheave designs have often been developed and evolved empirically, consequently many existing sheaves are not necessarily subjected to the detailed analyses that are possible using todayÆs design tools. The design philosophy for sheaves is that the rope should be the weakest link in the system so that associated equipment can function safely for any load up to rope break. A number of failure mechanisms must be considered, but buckling is often prominent. During the course of investigating the feasibility of upgrading the hoisting capacity of a winding system, the capacity of all critical components was reviewed. The sheaves in the system were found to have insufficient spoke buckling capacity for the specified rope. A proposal to increase the spoke buckling capacity by connecting spokes together using a simple tie arrangement was evaluated and found ineffective. An alternative tie arrangement concept was developed and evaluated and shown to be adequate. This paper describes the finite element model, analysis approach and results for the original sheave and the two modifications. The contribution of the sheave rim to the total buckling capacity is evaluated. Some practical issues for spoke tie modifications are discussed.

Jan 1, 2005

By Fredrik Sarvell, Harald. Ihler, Veli-Matti Uotinen, Jukka Rantala

"Many of the valid international building codes state that the lateral support provided by the soil is sufficient to prevent buckling of fully embedded piles. However, the development of small diameter micropiles and especially the use of high strength steel have evolved to applications including high capacity elements. The ultimate structural load bearing capacity of a pile in a cohesive soil is decided by examining which gives the lowest value, the peak buckling load and the resisting moment provided by the surrounding soil medium or the structural capacity of the pile cross section. In both cases, the initial deflection of the pile is a significant factor when the axial load bearing capacity of the pile is determined. Steel micropiles are joined commonly with mechanical splices. A less rigid mechanical splice is often a weaker hinge that allows the pile to bend and deflect more during installation increasing the initial deflection of a pile. In addition the less rigid splice element decreases the bending capacity of a jointed pile section and the ultimate axial load capacity of the entire pile. A series of FE analysis performed for various pile sizes suggest that the steel pipe piles including separate pile sections and mechanical splicing elements should have the combined bending stiffness of EIshaft = 0,75 × EIpile. This requirement yields to the buckling resistance of at least 96 % of the solid reference pile with the sameinitial eccentricity in similar soil conditions.IntroductionMany of the valid international building codes state that the lateral support provided by the soil is sufficient to prevent buckling of fully embedded piles. However, the development of small diameter micropiles and especially the use of high strength steel have evolved to applications including high capacity elements. The potential buckling of these very slender high capacity piles in soft soils may in many cases be the controlling design factor of the pile, especially with end bearing micropiles.A typical sequence of soil strata in Nordic countries, such as Norway, Finland and Sweden, constitutes of friction soil or dry crust clay on top of soft clay followed by till. This soil stratum often rests on solid bedrock of granite or gneiss. Conditions like these are suitable for slender end bearing piles subjected to buckling and especially steel pipe piles where most of the material is located at the edge of the cross section. Other reasons for using slender steel pipe piles are for example fast installation with minimal waste, efficient manufacturing and relatively well established design and execution procedures. Minimum quality criteria’s regarding splices for steel pipe piles are recommended to be set as national provisions to ensure quality and comparable procurements in foundation business."

Jan 1, 2014

By Wallace Ernesto Sant Anna Ramos

O Buckman Onsite® é um novo portal web para clientes com interface para um painel de dados, que propicia ao cliente e representante de serviços da Buckman, o acesso a informações essenciais sobre as operações neste cliente. O presente trabalho visa mostrar as vantagens e benefícios de se utilizar esta nova ferramenta manipulando os dados de controladores automatizados, dados de controle manual, ficha de segurança de produtos químicos e outras informações importantes para o processo.

Aug 17, 2017

By J. van Driel

NOx is a growing concern for acid plant operators due to recent legislation reducing the allowable stack limits, as well as continually more stringent requirements for product acid quality. NOx also causes a major problem during maintenance as NOx rich acid residues fume following exposure to moisture in the air. Until recently, the solution for NOx related issues was to treat the symptom, rather than the cause. NOx in product acid was treated using chemicals and the NOx in the plant stack was generally left untreated. As part of an environmentally driven change in concentrates, Budel Zink installed the first gas phase NOx destruction process to be incorporated into a commercial scale acid plant. Nitrogen oxides contained in the process gas are reduced selectively with ammonia over a catalyst to form nitrogen and water. As a result, the NOx reduction is in agreement with the permit requirements.

Jan 1, 2002

By J. W. Thomson, H. J. Lloyd, R. J. Taylor

"THE HOLLINGER MINE has been producing gold and by-product silver almost continuously for forty-eight years. The value of current production is $10,000,000 annually from one million tons of ore. Its management •has, particularly over the past decade, increasingly . concerned itself with the problem of profitable operation in a time of steadily rising costs and a fixed price of gold. At one period in the life of the mine, before World War II, production resulted in yearly profit margins that were stable and relatively thick. In winning gold from a series of inconsistent vertical ore lenses, operating management was much better protected than it is today against a general rise in cost or dip in grade of ore. The tissue-like thinness of present-day margins demand more careful handling. A sharp rise in costs, if protracted, could easily rip the tissue to shreds and close down the business. The counter-measure of raising grade and gutting the mine would bring on the end perhaps more rapidly, without having contributed much to the recovery of our national re-sources, nor to community welfare. The alternative is to keep costs under control."

Jan 1, 1960

By H M. Ahmed, W S. Dunbar

Construction of cave mining systems requires significant capital expenditure and long-term commitment of human, equipment and material resources before production commences. Risks and uncertainties of these large-scale mining projects are significantly higher than for small-scale projects. This is due to the complexity and interactions of the construction schedule components and the large scale and uniqueness of such projects. One way to successfully manage construction uncertainties that would lead to schedule delays is to include a reasonable cost contingency in the budget estimation. A real options approach based on the least-squares Monte Carlo (LSM) method is used to estimate cost contingency associated with schedule uncertainty in mass mining projects. Cost contingency is estimated as the cost of potential project crashing (acceleration) decisions, which pays for not extending the schedule. While such a significant undertaking is expected to be subject to some delays, these can have an enormous impact on the economic value of such projects. The value of the crashing option was explicitly formalised into the process of valuation, as it is assumed to be a single option being considered in the valuation at every decision point prior to the construction completion date. As a part of the proposed method, a stochastic function for the percentage of remaining scope of work for the remaining duration of the entire project was integrated into a framework of numerical simulations. This ensured that this function can implicitly account for sources of schedule uncertainties for projects represented by multiple and overlapping work packages. The LSM method was applied to a real case scenario in an operating block cave mine, with modified scale and features. The results yielded by the LSM method indicated that significant changes in capital budget allocation stem from variation in a contractor’s risk perception and confidence level of estimated delays.CITATION:Ahmed, H M and Dunbar, W S, 2016. Budget estimation and contingency allocation of block cave construction using least-squares Monte Carlo real options, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 801–808 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016