Search Documents

By M. Y. Mohassab-Ahmed

In an effort to develop a novel flash ironmaking process, the chemistry of selected slags was investigated. In different ironmaking processes, the molten bath (iron-slag bath) is expected to be in contact with gas atmospheres of H2/H2O, CO/CO2/H2/H2O, and CO/CO2. The latter was investigated to allow comparison with the blast-furnace conditions. The slag composition was selected to resemble that of the blast furnace with CaO/SiO2 in the range 0.8 to 1.4. The temperature range was 1550 to 1650°C. The oxygen partial pressure was maintained in the range 10-10 to10-9 atm. The effect of water vapor on the chemistry of the slag as well as the equilibrium reactions involving the slag has been studied for the first time. H2O dramatically affects the chemistry of the slag and strongly affect the phase equilibria in the slag as well as the equilibrium distribution of elements between slag and molten metal.

Jan 1, 2014

By Courtney Young, Jerome Downey

"The various technologies developed for treating spent potlining (SPL) from primary aluminum smelters have been reviewed on several occasions. The technologies generally involve physical, chemical, and thermal processes, either individually or in combination, with the primary objective of total recycle, waste minimization, or complete disposal. In general, those technologies geared for recycling involve separations and are therefore subject to recovery inefficiencies that are attributed to several factors. However, the inefficiencies could be reduced or possibly eliminated if the pots were designed for recyclability. This concept is applied to SPLASH, a recently developed SPL management technology.IntroductionAluminum is produced by molten salt electrolysis via the Hall-Héroult process. The process is conducted in an electrolytic “pot,” which is comprised of a steel frame first lined with insulating refractory brick, and then conductive graphite blocks, which serves as the carbon cathode [1, 2]. These materials are collectively referred to as “potlining.” Anodes comprised of petroleum coke/pitch are suspended above the pot and extend down into the molten cryolite (Na3AlF6) electrolyte. The electrolyte temperature is maintained at approximately 980 °C by resistance heating as low voltage (4-5 volts) and high current (50,000-300,000 amps) are applied across the two electrodes.High purity alumina is added to the cryolite bath, where it dissolves and becomes amenable to aluminum reduction at the cathode:"

Jan 1, 2008

By E. F. Vegman, Ndabezinhle Dube

"In the practice of conventional sintering, production is always afflicted with the problem of being unable to get a uniform quality of produced sinter in the bed. Invariably the top layer of the sinter cake is composed of weak but highly sinter, while the bottom layer is over-fused, forming a sinter that is very strong but less reducible. These symptoms point to a variable distribution of the heat balance in the process of sintering which results in a deficit of heat in the top layers of the sinter bed and an excess of heat in the bottom layers, due to an increasing input of regenerated heat in the heat balance down the bed. This causes losses in the productivities of the sinter machine and the blast furnace.The current work was designed to improve on the solution to the above problem through the establishment of a more accurate combustion zone heat balance of the sintering process. This development is mostly on the method of determining the regenerated heat input in the overall heat balance. Previous methods were based on the assumption that the width and the velocity of the combustion zone remain constant through out its whole life, which is not the case since tests have shown that both its width and velocity increase as the combustion zone moves down the bed. In this work, these factors have been taken into account. Tests and calculations using the model were carried out for haematite and limonitic ores. The high sensitivity of the model to changes in the sinter mix composition and sintering conditions was demonstrated.The results present the following prospects:• The minimum theoretically possible coke breeze consumption during the sintering of any type of iron ore fines, under any sintering conditions, can be established.• The model can be used to control the metallurgical quality of the sinter in any point in the sinter bed since calculation data includes desired basicity, combustion zone temperature and FeO content in the sinter produced."

Jan 1, 2001

By William Petruk

An investigation was conducted to determine whether mineral liberation data obtained by one image analysis technique are the same as data obtained by another image analysis technique. The liberated vs non-liberated, volume % and weight % techniques for measuring mineral liberations by image analysis were tested. The results show significant differences between the values obtained by the different techniques. The lowest liberation values were obtained by the liberated vs non-liberated technique and highest by the weight % technique. It is interpreted that the weight % technique produces the most realistic results. The weight % technique also produces data that can define mineral associations for the unliberated grains. These include (1) mineral quantities in particles that contain different amounts of unliberated mineral, (2) mineral quantities in particles that have different size ranges, and (3) mineral quantities and degrees of liberation for specific minerals in particles of different size ranges.

Jan 1, 1996

By G. Coryell, S. Blaskovich

"A computer model has been developed to simulate the flash furnace and converter operations at the ASARCO Hayden Copper Smelter. The focus of the modeling was to optimize the converter operation to eliminate high matte level episodes in the flash furnace. These episodes (reducing feed to the furnace) resulted from the lack of converter operation scheduling. The model provided ""what if?"" scheduling scenarios that led to increased efficiency of the converter and flash furnace operations.This paper discusses alternatives studied to optimize the converter operation and the development of the computer modeling program, including implementation of the project. The discussion details the results of the project including the conversion from batch to a real time converter scheduling process. IntroductionASARCO's Hayden Smelter consists of a fluid bed drying system, an Inco oxygen flash smelting furnace, Peirce Smith converters, two anode furnaces and two casting wheels, gas cleaning plant, 2800 stpd sulfuric acid plant, 650 stpd oxygen plant and 200 gpm water treatment plant. The process flow sheet of the plant is shown in Figure 1.Over the past several years, the Hayden smelter has been involved in productivity improvement and cost reduction programs. This has been necessary to become a low cost copper producer in today's market. Part of the productivity improvement program was the use of process control to streamline the flash furnace and converter operations. Process control, through the use of computers and electronic controllers, has played an increasingly important role in optimizing processes in the Hayden Plant since the startup of the Inco flash furnace in 1983."

Jan 1, 1989

By Andrew Case

The Port Nickel facility in Braithwaite, Louisiana, is known for pioneering hydrometallurgical processes for the 'separation and recovery of nickel, cobalt and copper. Ten years ago, in 1985, a new CRI-MET process for the recovery of molybdenum, vanadium, nickel, cobalt and alumina from spent catalysts was developed and implemented. Spent- catalysts from the petroleum industry consietute the majority of feed. These are not only a valuable-source of metals, but due to EPA regulations are frequently classified as hazardous under RCRA. Molybdenum and vanadium are selectively leached in an oxidative hydrothermal step. Alumina is then extracted in a caustic digestive leach. The unique technology produces four primary commercial products l molybdenum trioxide, vanadium oxide, aluminum trihydrate and nickel-cobalt concentrate. This paper discusses the process, modifications. during ten years of operation, and the relationship of these modifications to the future of the catalyst recycling business.

Jan 1, 1995

By Jilai Xue, Jun Zhu, Liang Liu

"Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice with a heating process causing large energy consumption and high production costs. In this work, the floatation separation at room temperature were carried out using two types of skarn scheelite ores. The results showed that CaO and Na203 are better than NaOH as a regulator in pH value. In the rough floatation and first cleaning floatation, CaO (500g/t), Na203 (3000g/t) were used as a pH regulator, waterglass (4000g/t) was as a gangue depressant, oleic acid or sodium oleate were used as a collector. The degree of the obtained W03 concentrate was more than 65% (commercial product).IntroductionThe mainly gangue in scheelite are quartz, calcite, barite and some rare metal ores. There are three main types of scheelite for floatation: scheelite--quartz (silicate minerals) type, scheelite-calcite/ fluorite type, scheelite--calcite/fluorite/barite type. Generally speaking, scheelite--quartz type is separated easily, and others are difficult, on the contrary. The last two kinds of scheelite are always called scheelite--calcite/fluorite (barite) type, because there are similar floatation ability and floatation process between them. Scheelite, calcite and fluorite have same cation - Ca2+, it makes them have close floatation property [1]. Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice.The traditional separation method is a heating floatation process (Petrov's process) [2]. It can deal with many kinds of scheelite, and can be obtained stable quality ofW03 concentrate. On the other hand Petrov's process causes large energy consumption, high production costs and bad operational environments. Since 1980s, scheelite ambient temperature floatation has become the mainstream of study [3]. Nowadays more and more studies on scheelite floatation focus on complex reagent system [4, 5], rigid operating rules and at the same time development new regulator [1, 5]. Some research show there are new regulators can concentrate scheelite efficiently, but it may cause high costs, potential pollution and difficulty to spread. Oleic acid and sodium oleate used as collector have high adsorption capacity to scheelite, but same to calcite and fluorite[6]. So, it would not get ideal effect for separation of scheelite. In this work, the floatation separation at room temperature were carried out using two kinds of skarn scheelite ores. Calcium oxide and sodium carbonate was used as a pH value regulator, waterglass was used as a depressant and Oleic acid/sodium oleate was used as a collector. The result of experiment showed that the degree of the obtained W03 concentrate was more than 65% by one time ambient temperature roughing floatation, several times ambient temperature cleaning process."

Jan 1, 2014

By N. Menad

Thermal treatments of five different types of non-ferrous metallurgical wastes, under controlled atmosphere, were carried out at temperatures lower than 800 °C. The aim of these treatments was to reduce the toxic elements content and to increase that of valuable metals in the residue. <Best results were obtained by their treatments in air or hydrogen or successively both of them. Simple treatments using air or hydrogen of three samples allowed the elimination of more than? 95 % of their toxic elements and&apos; almost doubled their valuable metals&apos; concentration. For the rest two samples, combined treatment was necessary for their efficient decontamination and the concentration of valuable metals, in the treatments residue, to a reasonable value. Most of the solids issued from these treatments can be recycled in .the current non-ferrous metallurgical processes.

Jan 1, 1995

By Nicola Baldo, Marco Pasetto

"Recycling of tyre rubber in the road pavement, may be one of the best way to reduce waste tires in large quantities and, at the same time, improve some engineering properties of asphalt mixtures. The paper discusses the results of an experimental study, developed in order to analyse the potentialities of crumb rubber from road tyres in bituminous mixtures, using the dry process. Two types of porous asphalt mixtures and reference mixes without rubber were formulated by the traditional Marshall methodology, and mechanically evaluated by means of the Indirect Tensile Stiffness Modulus test, the Creep test (with confinement), and the Indirect Tensile Fatigue Test. Results of this study indicate that the tyre rubber has a positive influence on the performance characteristics, depending also on the grading and volumetric properties of the mix being studied: an interesting increase of the fatigue life, a better stiffness behaviour at lower temperatures and a bigger permanent deformation resistance at high temperatures are guaranteed. Introduction Recycling the rubber from used tyres, in the construction of road pavement layers, is potentially one of the more interesting and advantageous solutions from both the technical and environmental points of view, in order to reduce the total amount of car and lorry tyres to dispose. In road-building techniques, a technology, termed “wet”, for modifying bituminous binders with crumb rubber has by now become well consolidated. There have been numerous scientific studies conducted on this technology and its applications, particularly in the United States, where it has been adopted and codified in specific technical regulations (ASTM D-6114). If the wet process can be considered amply tested, the same cannot be said for a second technology, termed “dry”, which deserves careful study to evaluate its suitability and advantages. In “dry” processes, the rubber is usually used as a partial substitute of aggregate of equivalent grading and mixed with bitumen after integrating the crumb rubber in the lithic skeleton."

Jan 1, 2008

By Ramana. G. Reddy, Haoxing Yang

The electrodeposition of zinc from zinc oxide using urea and choline chloride mixture in a molar ratio 2:1 is investigated in different experimental variables, namely, the concentration of added [BMIM]HSO4, temperature, and applied cell voltage. The additive, [BMIM]HSO4, was determined to have beneficial effect on the current efficiency, energy consumed in the process and surface morphology of the deposits. The highest current efficiency (92.6%) and lowest energy consumption (2.92kWh/kg) was obtained for solution with 20mg/mL [BMIM]HSO4. The morphology showed the formation of absorbed additive layer on the cathode at higher concentration of additives. Experiments were conducted at different temperatures between 343K and 388K and at various applied cell voltages between 2.7V to 3.6V to determine the best experimental conditions. By varying temperature, highest current efficiency (91.3%) and lowest energy consumption (2.69 kWh/kg) was obtained at 373K. The electrodeposition process is enhanced between the applied voltage 3.0-3.3V by achieving lower energy consumption (2.75~3.06kWh/kg) and higher current efficiency (88.4~89.7%). SEM images showed grain size is significantly increased in higher applied voltages. While at higher temperatures, it seemed to generate particle growth as clusters at the outer deposit layer.

Jan 1, 2014

By Run Huang, Xuewei Lv, Songli Liu, Chenguang Bai

"Titanium alloy was prepared from titania-bearing blast furnace slag (Ti-BF slag) by aluminothermic process in an induction furnace. The effects of aluminum amount on the titanium silicon yield and titanium recovery ratio were studied. The phase transformation and chemical composition of the prepared alloy were investigated by X-ray diffractometry (XRD) and X-ray fluorescence (XRF) respectively. It was found that the mass fraction of silicon and aluminum increased with increasing the aluminum amount, however, the mass fraction of titanium increased first and then decreased with increasing the aluminum amount. Furthermore, both the titanium alloy yield and titanium recovery ratio increased with the increase of aluminum amount. The main phases of the alloy were TixSiy and AlTi3. The titanium alloy samples prepared in various conditions had a composition (wt.%): 38–50% Ti, 29-34% Si, 4-11 Al%, 1.6-2.2 Mn%.IntroductionPanzhihua and Xichang regions in the southwest of China are rich in vanadium-titanium magnetite containing iron, vanadium, titanium and gangue. According to the characteristics of the resource, iron and vanadium are successfully recovered with a blast furnace process and a converter process. However, most content of titanium are entered in the blast furnace slag with TiO2 22% -26% and metallic Fe 2%–6% called Ti-BF slag. Due to the dispersed distribution of Ti in various fine grained mineral phases with a complex combination between Ca, Al and Si, it is difficult to recover the Ti components[1]. This slag is generated at a current rate of 3.6 million tons per year, which adds to the existing 70 million tons of slag produced so far[2]. The slag has had to be piled as large as the mountains, which not only waste of resources but also cause a pollution of the environment. Therefore, the study of integrated utilizing Ti-BF slag has become very significant."

Jan 1, 2012

By Jing-she Li, Hai-yan Tang, Cheng-song Liu, Wei Liu

"In order to effectively utilize cheap and low quality iron ores, a hematite ore in a certain steel plant in Xinjiang was researched on to obtain ""iron increase and silicon reduction"" by ore dressing operation experiment and the performance indexes of the hematite ore were optimized. Based on the fundamental characteristics and high-temperature properties of the concentrate after ore dressing and other five kinds of iron ores which were co=only used in this steel plant, ore matching principles were proposed and a sintering ore blending optimization model was established. Finally, sinter pot test was carried out to verify the validity and practicability of the sintering ore blending optimization model which was aimed at giving consideration to the sintering indexes and the cost.IntroductionIn recent years, the price of imported iron ore with high quality is always at a high level, while iron ore self-sufficient rate in China is less than 50%. Enormous market demand and high dependence of domestic enterprises on imported iron ore makes the price of it hardly return to rational. In order to get rid of the situation of long-term meager profit and even deficit, more and more iron and steel enterprises in China transit their focus of reducing production cost to the utilization and development of relatively cheap but low-grade iron ore resources at home[l-4l_ However, besides the disadvantages of low iron grade, high content of impurities and complex embedded properties, the high-temperature properties of iron ore often go beyond the suitable ranges for producing sinter with high quality. Thus directly utilization of this kind of iron ore without ore dressing process would probably affect the metallurgical performance and indexes of sinter ore.Previous research and production practice have shown that traditional iron ore matching in sintering mainly focus on the reasonable collocation of properties of iron ores with low quality and high quality, but pay less attention to ore dressing process of low quality iron ores and matching them with high quality iron ores. Actually, compare with directly utilization, iron ores with low quality after ore dressing have higher suitability for matching with high quality ones which is beneficial to reduce the consumption of iron ores with high quality and control the production cost of sintering [5-s1."

Jan 1, 2014

By I. A. H. Schneiderl

Eichhornia crassipes approaches being a scourge in many parts of the world, .choking waterways and hindering transport upon them. At the same time it is known to readily abstract heavy metal ions from water and, thus, aids in the removal of heavy metals found in such waters. This paper considers the possibility of using specific parts of the plant as an inexpensive adsorbent for the removal of heavy metals from contaminated chemical and mining industry waste waters. In particular the root of the plant was found to be an excellent accumulator of &apos;heavy metal ions including uranium from solution. It is. also suggested that dried roots of the plant ?might be placed in simple bags and used in a very low cost metal ion removal system.

Jan 1, 1995

By V. P. Keran

The lead and copper smelting processes employed by Mount Isa Mines Limited, Mount Isa, Australia, are used to illustrate an operating viewpoint of some problems and solutions encountered in existing commercial sulphide smelters. The smelting processes discussed; include updraught sintering, blast furnace and reverberatory smelting, and converting. Selected examples are given of methods implemented, and options available, to improve the productivity and efficiency of conventional smelting processes.

Jan 1, 1983

By C. Pereira

Spent nuclear fuel (SNF) can be treated in a molten salt electro refiner for conversion into metal and mineral waste fonns for geologic disposal. The fuel is dissolved in molten chloride salt. Non-transuranic fission products in the molten salt are ion-exchanged into zeolite A, which is subsequently mixed with glass and consolidated. Zeolite was found to be effective in removing fission product cations from the molten salt. Breakthrough of cesium and the alkaline earths occurred more rapidly than was observed for the rare earths. The effluent composition as a function of time is presented, as well as results for the distribution of fission products along the length of the column. Effects of temperature and salt flow rate are also discussed.

Jan 1, 1996

By Pengfu Tan

In order to understand and control the formation of dioxins and furans in iron ore sinter plants and to possibly avoid expensive end-of-pipe removal stages, thermodynamic calculations on the stability of PCDD/Fs have been combined with sinter process modeling by means of kinetic simulations and computational fluid dynamics. Three thermodynamic databases of PCDD/Fs, derived using the Group Additivity approach and two computational molecular modeling methods, MNDO and PM3, respectively, combined with the SGTE database have been used to model the PCDDIF formation and the PCDD/F isomer distributions in iron ore sintering. The results show very similar conditions for the PCDD/F formation using the different databases. Concerning the isomer distributions of toxic PCDD/Fs, the calculated data derived from the MNDO method showed optimum agreement with measured values from industrial furnaces. The thermodynamic calculations also proved that the isomer distributions found in combustion processes are equilibrium values, while the concentration ratio of PCDDs and PCDFs in the wind boxes does not represent an equilibrium state. A CFD model of iron ore sintering was developed including the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. On the basis of these information and experimental observations reported in the literature possible pathways for the PCDD/F formation in sinter plants have been identified: PCDD/Fs are formed in the critical temperature region of 250 to 450 °C below the combustion zone, are then carried downwards with the gas and condensed close to the bottom of the sinter bed. Transported to the discharge end with the solid mixture, they are again released into the gas phase when the flame front approaches the bottom. PCDD/Fs are also formed in the last wind boxes when the hot off-gases cool down and reach the critical temperature range. Consequently, methods to reduce the dioxin formation reactions are proposed including inhibitor addition to the sinter feed and off-gas quenching.

Jan 1, 2003

The U.S. Bureau of Mines investigated CaF2-assisted H2SO4 leaching to extract Mn from domestic silicate manganese resources. A pyroxmangite ((Mn,Fe)Sio3) ore containing, in pct, 34 Mn, 23 Si, 3 Ca, and 1 Fe was leached at 90° C for 3 h in a solution containing, in g/L, 12 Mn, 140 H2SO4, 130 (NH4)2SO4, and 5 CaFz. Manganese extraction of 92 pct was achieved. Manganese of greater than 99 pct purity was prepared by electrolyzing the purified pregnant solution at a current density of 50 mA/cm2. The current efficiency was 65 pct.

Jan 1, 1991

By J. W. Perez

Raw coal will often break intragranularly in either a completely random way or in a differential mode where one species will have a different rate of breakage than another. Locked coal-ash and coal-pyrite particles can also break by the preferential detachment of one species from another along zones of inherent weakness in locked particle assemblages. The mode. cf breakage is largely a function of the nature of the feed, but it is also influenced by the comminution device and the operating variables. Evidence of breakage of particles in the various modes is seen in the crushing of raw coal and middlings particles with a rotary beaker, jaw crusher, rolls, hammer mill and rod mill. Evidence from the literature indicates the detachment mode is often important for coal, ores and metallurgical products. Further confirmation comes from the crushing of a specially prepared &apos;ore&apos; of sized magnetite in plaster of Paris.

Jan 1, 1988

By Achilles J. B. Dutra, Carlos M. Juarez

"The use of thiourea as a gold leaching reagent has been extensively studied by many researchers, and it has proved to be promising for some cases as refractory ores. Otherwise, the recovery of gold from these solutions did not receive so much attention. In this paper the electrowinning of gold in acidic thiourea solutions was studied by voltarnmetry and chronopotentiometry. An adsorption step was detected prior to Au(I) reduction and the diffusion coefficients at 25°C for Au-TU complex and FD were found to be 1.00 x 10.5 cm2 S-I and 1.98 x 10-5 cm2 S-I respectively. At -0.350 V (SCE) a passivation probably due to TU adsorption was observed. For higher overpotentials hydrogen evolution was the main reaction.IntroductionThe use of acidic thiourea solutions for the extraction of gold and silver has shown to be a promising alternative to the traditional process of cyanidation, specially for certain refractory ores (1-3) and electronic scrap (4). In some cases, the industrial scale was reached (1,5). The thiourea leaching of precious metals presents advantages over cyanidation, as faster kinetics, lower toxicity and lower sensibility to base metals; however the costs due to high thiourea consumption impairs its use.The majority of the publications on thiourea processing of gold is on leaching. Many are review papers (5-7). Recently, the adsorption and desorption of the gold-thiourea complex on activated carbon and ion exchange resins have been studied (8-11).Little research has been done on the electrowinning of gold from acidic thiourea solutions, most of it has been carried on the seventies and beginning of the eighties in the former USSR (12-17) and concerned the eletrolytic extraction of gold in tridimensional cathode cells.The present paper concerns the cathodic behavior of the gold-thiourea complex in the presence of formamidine disulfide in order to provide information on the electrowinning of gold from solutions obtained directly from leaching or from an elution process."

Jan 1, 1997

By Wanderson Silva Rodrigues, Paulo Adão Marinho dos Santos, José Antonio Silva Souza, Luis Alves Venancio, Emanuel Negrão Macedo

"1 AbstractThe production of alumina from bauxite using the Bayer process generates 0.7 to 2.0 ton of the residue known as red mud per ton of alumina. This material has no large scale current use and is usually stored. This paper shows that it can be used in a suspension with water as a gas effluent cleaner with high efficiency to remove SO2. It can substitute other materials currently used reducing the overall environmental impact and potentially reducing the cost of gas treatment.2 IntroductionThe production of millions of tons per year of alumina around the world generates from 0.7 to 2.0 ton of the residue known as red mud per ton of alumina. The vast majority of the red mud is stored in large sealed lakes. Due to the high reactivity this material is considered dangerous and currently there is no operating process capable of reuse all the material produced at any refinery. These lakes after filled of solid material eventually have the surface revegetated. In any cases they will remain as an environmental passive and need monitoring for decades. The search of industrial processes that combine the cleaning of gas effluents emission and reuse of these residues can contribute to the reduction of the overall impact of the alumina production process.The main objective of this work is to study the efficiency of the red mud as alternative raw material for the control of emissions of SO2 in combustion gases. Usually this is made through alkaline solutions of CaCO3 or NaOH in absorbing equipments like spray towers or packed column. This project main objective is to study the reaction of the SO2 with a suspension of red mud and water in order to obtain the basic parameters to design equipment capable of process this reaction on a pilot scale. With that goal compositions of red mud on spray were processed with flow of gas containing SO2 with concentration similar to the exhaust gases of the combustion process of the refineries."

Jan 1, 2011