Search Documents

By Fuxing Yin, Akira Sato, Yoshiaki Ohsawa, Kohji Kawaharai

"INCRAMUTE alloy (nominally 45Mn-53Cu-2Al wt. %) has a specific damping capacity as high as 0.4, through a solid-solution and aging treatment. The damping behavior of the alloy is highly temperature-dependent and shows a peak near room temperature. The inadequate strength in the high damping condition restrains the practical application of the alloy, as structural components. Ferromagnetic MnB particles are dispersed in the alloy during induction remelting the matrix alloy in an argon atmosphere. Surface modification of the MnB particles by mechanical alloying (MA) and suitable control of the addition process cause a homogeneous distribution of MnB particles in the alloy. In the composite containing 2 wt. % MnB particles, temperature dependence of damping capacity is improved, and higher damping capacity is still retained in the temperatures over 60 °C. Meanwhile, the Young's modulus and tensile strength were also increased by about 20%. The roles of the MnB particles in improving both damping behavior and mechanical properties were also discussed.IntroductionMany viscoelastic materials, such as rubbers, polymers and plastics, have the superior ability to damp vibration and noise. However, in the applications as structural materials the high damping capacities of materials are pursued upon the satisfactory mechanical properties, especially those at elevated temperatures. Damping alloys are finding more and more applications in structures where noise and vibration ·should be ·eliminated. Specific damping capacity (SDC), defined as the ratio of the energy dissipated to the maximum vibration energy stored per cycle, is usually used to evaluate the damping capacity of alloys. INCRAMUTE damping alloy, developed by the International Copper Research Association, Inc., has a nominal composition of 45Mn-53Cu-2Al in weight percent. The high damping· microstructure of this alloy is obtained through the solution treatment at 820 °C followed by a water quench and aging at 400°C for 10 hours followed by cooling to room temperature [1]. With the heat treatment, a SDC peak ·vs. temperature of as high as 0.4 was observed in the alloy at the strain amplitude of about 10-3 while a tensile strength of about 500MPa was sustained."

Jan 1, 2000

By Peter Ehren

Global Geoscience is developing a Rhyolite Ridge project, a shallow boron-lithium resource deposit, located in Nevada about 25 km from Albermarle’s Silver Peak operation. The main minerals of interest are the boron mineral searlesite (40%wt) and lithium containing clay minerals. These minerals are found among principally calcite, feldspar, muscovite, dolomite, and quartz. The equivalent commercial value is about 7–9% boric acid (H3BO3) and 0.8–1.0% lithium carbonate (Li2CO3) equivalents. Selective agitated leach tests at SGS Lakefield laboratory showed that searlesite can be acid leached between 20 and 75 °C and at a pH lower than 4. On the other hand, lithium can be leached between 20 and 75 °C and at a pH lower than 1. In other words, lithium can be recovered at low temperatures if sufficient free acid is available, which gave the motivation to investigate heap leaching of the mineral. The PLS contains boric acid, magnesium, sodium, lithium, potassium aluminium, and iron sulfates.

By Marion Dattilo

The search for an improved anode for the electrowinning of lead from fluosi1icic acid medium has led the U.S. Bureau of Mines to investigate composites. Polymer bonded metal oxide powders which may contain catalyst additions were prepared by pressing. These composites display an improved activity toward the oxygen evolution reaction over electrodeposited lead dioxide on titanium, carbon, and nickel substrates. These composite electrodes contain 5 to 10 wt. " binding polymer, with the balance being metal oxides. Lowered anodic potentials achieved using the compnsite anodes resulted in lower levels of lead dioxide deposition during electrowinning.

Jan 1, 1995

By Pedro A. Netto, Giulio R. Altoé, Sergio N. Monteiro, Ygor M. Moraes, Frederico M. Margem, Gabriel O. Glória

Since environmental issues are becoming more and more important Worldwide. Nowadays, Natural fibers are been used to substitute the synthetic ones. Although PALF fiber is an important natural fiber and its mechanical Properties surpass in various aspects some other lignocelluloses fibers, such few studies have been conducted with the fiber obtained from leaf of PALF plant. In order to better evaluate the mechanical properties and possible applications, this paper aims to improve the elastic modulus of the PALF fiber by Weibull statistics, by evaluating their mechanicals properties and possible applications. The fibers were divided in diameter intervals and the tensile strength and elasticity modulus were measured in each range. The fractured surface was examined using scanning electron microscopy. The results, interpreted by the Weibull statistical method, showed a correlation between the fiber elastic modulus and its diameter.

Jan 1, 2015

By Augusto Viana Leandro Teixeira

Rare Earth Elements (REE) are fundamental for modern life products and green technologies. Supply constraints and the price peak of 2011 boosted intensive research for alternatives for processing and separation. Complex monazite- type, rare earth ores usually contain high acid consumption impurities, such as iron and aluminum, and radioactive thorium in their composition. These impurities are not removed by conventional concentration processes due to fine, micro-level association between the REE carrying minerals and the gangue minerals. This work presents a selective process route for REE extraction from iron-rich, monazite ores. The process involves sulfation by addition of concentrated sulfuric acid and pyrohydrolysis at temperatures of approximately 700–750 °C. Experimental results show REE extraction higher than 70% and low iron (below 5%) and thorium extraction (below 10%). A method based on thermogravimetric analyses was shown to be adequate to predict the behavior of a given ore sample in the sulfationselective pyrolysis-leaching process.

By A. Broussaud

An original methodology has been developed for steady state simulation of selective grinding and mineral liberation in rod and ball mills. Three fundamental aspects of the methodology are presented successively : modeling ore texture, modeling grinding and its selectivity, and modeling mineral liberation. The methodology for modeling ore texture includes the conversion of 2D data into 3D reconstructed information and the use of the BILCO coherent material balance software. The models for grinding Simulation are classified into three levels, corresponding to three levels of available experimental data. All models account for grinding selectivity and for variations of engineering para-meters and operating conditions. An algorithm has been introduced to forecast mineral liberation, compatible with accurate simulation of selective grinding, which generates reasonable results.

Jan 1, 1987

By Qingyun Huang, Wei Lv, Junyi Xiang, Xuewei Lv, Chenguang Bai

The kinetics of iron leaching from ilmenite in hydrochloric acid solutions were investigated. The effects of pre-oxidation roasting, leaching temperature, and holding time on iron extraction rate were determined. The results obtained show that the extraction of iron is significantly enhanced by pre-oxidation roasting and increasing leaching temperature from 75 to 108 °C. The results of the kinetic analysis of the leaching data indicate that the reaction is controlled by diffusion through the product layer. The apparent activation energy for the extraction of iron has been calculated to be 62.5 and 55.1 kJ/mol for untreated and oxidized ilmenite, respectively.

Mar 1, 2018

By Oscar Restrepo, Juan C. Nino, Henry A. Colorado

New and extraordinary physical-chemical properties of materials at nanoscale open up new applications for the building and infrastructure industry such as structural reinforcements, electronic properties and energy harvesting. Therefore the issues and risks associated with the manufacturing of nanomaterials are now of big concern due to the large volumes and typical processing involved in this industry. This paper presents a discussion and selected applications of nanotechnology in the construction and building materials: from metals and alloys, clay and minerals, ceramics, cement and concrete, asphalt, wood and composites, to finishing systems and some of the most used characterization techniques. Besides the progress in some areas, nanotechnology is just emerging in this field, with many challenges and opportunities, problems unsolved and business opportunities. A discussion regarding the potential health issues and risks of using nanomaterials for workers and the potential environment effects is included as well. New images and diagrams are presented and discussed.

Mar 1, 2018

By Yong Li, Tao Jiang, Xiangxin Xue, He Yang

"In this paper, we describe the current status and research progress on the utilization of typical industrial solid wastes in China. We propose a creative method called “eco-utilizing wastes” with an aim of both integration and increment but without second-time waste and pollution, in terms of the characteristics of typical industrial solid wastes, such as titanium-bearing blast furnace slag, high-silicon iron tailing and boron-enriched slag as well as oil shale.Situation of Typical Industrial Solid Wastes in ChinaThough mineral resources in China are abundant, most of these are low grade ores. Moreover, the distribution of mineral resources is asymmetric, which causes the increase of cost and decrease of the economic benefit. Over-exploitation of mineral resources results in a large number of solid wastes. The accumulation of solid wastes not only means the waste of valuable resources, but also causes environment deterioration. There exist some problems in the current practice of the disposal of industrial solid waste, such as only emphasizing the final results and causing new pollution and waste [1]. So the research and development of a high value-added method has a high practical relevance to our nation. Based on the present status and research progress of industrial solid wastes in China, a creative new idea and method for eco-utilization of solid wastes is proposed in this paper."

Jan 1, 2012

By Fuqiang Guo

Scorodite (FeAsO4, 2H2O) is suitable mineral carrier for immobilization of arsenic-rich wastes. Its stability is, however, highly pH dependent (typically at 4 ≤ pH ≤ 7) and satisfactory only under oxic disposal conditions. In thiswork an encapsulation process using mineralized gels of aluminum hydroxy-oxides is developed to enhance the stability of scorodite under wider pH and redox potential range conditions. The encapsulation involves blending and ageing of synthetic scorodite produced by McGill’s atmospheric scorodite process with aluminum hydroxyl gels derived from controlled hydrolysis of aluminum salts. The amorphous hydrolyzed Al-gel encapsulates the scorodite particles,which upon short-term aging transforms into crystalline Al (OH)3/AlOOH mineral phases providing a robust protection microscopic barrier. Long-termstability testing demonstrates the encapsulation systemto be highly effective in suppressing arsenic release under either oxic or anoxic (100 mV < Eh < 600 mV) potential and neutral-alkaline pH (7 ≤ pH ≤ 9) ranges.

By D. G. Hattingh, A Els-Botes

"Considerable information is available on the factors influencing the iron-zinc reaction rate at 450° C of low carbon steels, in comparison there is a scarcity _of similar fundamental information of spheroidal graphite irons. This can be attributed to the more complex microstructure and ferrous alloy chemical analysis of spheroidal graphite irons. Hot-dip galvanizers have identified the complexity in controlling and predicting the thickness of the galvanized coating formed on commercial cast irons, which has serious financial implications for both the galvanizer and customer.Commercial hot-dip galvanizing has been in use for over 160 years and yet an elementary understanding of the dynamics associated with the hot-dip galvanizing of spheroidal graphite cast iron is still insufficient. To allow the. process to become a modem surface engineering technology, the fundamental aspects of the process must be thoroughly understood.When a clean iron or steel article is dipped into the molten zinc, zinc initially solidifies around the steel or iron. As heat is transferred to the article form the bath, this initial solidified zinc layer remelts and a series of iron-zinc alloy is formed by the reaction of the zinc with the surface of the article; on removal from the bath, some of the molten zinc is taken out on top of the alloy layers. At normal galvanizing temperature (450 °C), the reaction between iron and zinc is usually parabolic with time. The rate of reaction is rapid at first but then slows down and the coating thickness does not increase greatly if the article is immersed in the bath for longer times(1)."

Jan 1, 2000

By J. R. Odekirk

The nature of mineral distributions and locking characteristics in mill products are important factors in understanding mill performance. Such data are obtained by microscopic point counting methods. Reduction &apos;of point-count data from volume to weight percentages, and reduction of data for each size fraction back to a head sample requires lengthy hand calculations. The use of computer processing for such data reduction results in obtaining information on a realistic time basis. An example of computer processed point-count data is presented.

Jan 1, 1981

By Dan Michaelsen, Warwick Stewart

"PT Kaltim Prima Coal (KPC) is a large-scale truck and shovel operation mining thermal-coal in East Kalimantan, Indonesia. The operation produces 15 million tonnes of coal and mines over 120 million bank cubic metres of overburden annually. Approximately 35 percent of the waste rock is classified as potentially acid forming. Acid drainage must therefore be managed to prevent acid formation from spoil dumps and mined-out areas.KPC aims to prevent acid production in dumps by covering potentially acid forming spoils with materials identified as non acid-forming. The covers, built to engineering standards, minimise the flux of oxygen and water to pyritic spoils, thereby controlling the oxidation reaction, and reducing ARD discharge to negligible rates. Cover designs and cover materials vary according to stability, materials availability, equipment availability, and cost effectiveness. A modified field net acid generation (NAG) test procedure has been developed at KPC to identify and segregate overburden geochemical types. This paper discusses the ARD management strategies and operational procedures adopted by KPC to manage potentially acid forming waste rock. The development and field application of the NAG procedure at KPC is presented in a companion paper. Analytical"

Jan 1, 1999

By Zhihe Dou, Yu Fang, Zimu Zhang, Yan Liu, Xiaoli Jiang Dianhua Zhang, Guanting Liu

"With the idea of “waste control by waste itself”, we come up with the crafts of using waste calcium carbide to mineralize CO2 in electrolytic aluminum waste gas, design and make out “Venturi gas-liquid-solid three stage reactor”, do experiments under the system of CO2-Ca(OH)2, investigate the influence on gas absorption by pH meter; investigate the influence on diameter distribution , rise velocity of bubble and local gas hold-up by dual conductivity probes; investigated the absorption of CO2 in every stage reactor under different initial proportion of CO2 by intelligent gas measurement system. The results showed that the reactor can fully absorb the CO2 in waste gas, and it has largely shorten the time of absorption and improve the CO2 utilization compared with the single stage reactor.The residual proportion of CO2 in the gas is below 0.08% through the absorption of three stage reactor,which show that absorption is extremely improved.IntroductionCarbide slag is a kind of polluting hydrolysis reaction byproducts in producing carbide in wet reactor, and it is mainly comprised by Ca(OH)2, It's estimated that there are about million tons carbide slag are piled up per year. Carbide slag is a kind of industrial wastes that hard to deal with ,which are treated by land filled in the past. It would not only occupy a lot of land, but also lead to secondary pollution [1].CO2 is the main greenhouse gas by now. In 2010, global CO2 emission has reached 33.5 billion tons, while China has now become the world's second largest emitter of CO2, emissions accounting for about one-seventh of the world [2].As the experts estimates, the greenhouse gas emission of whole nonferrous metal industry may over 0.6 billion tons per year, while CO2 emission of electrolytic aluminum is 0.334 billion tons per year [3]. So it is necessary and pressing to discover the reusing CO2 of electrolytic aluminum. With the idea of “waste control by waste itself”, we came up with the crafts of using carbide slag to mineralize the CO2 in electrolytic aluminum waste gas, which was experimented on the counterflow-three stage-venturi reactor,and studied the local gas holdup, residual concentration of CO2 and the volumetric transfer coefficient in the reactor."

Jan 1, 2014

By C. S. Ek

As a continuation of previous work, further tests have been carried out to recover silver from the residues obtained in a zinc jarosite process. Selective flotation has been performed with different reagents, and ?cleaning steps have been introduced to upgrade the silver concentrate. Leaching of crude residues, as well as flotation tailings, has been carried out with cyanide and thiourea. Finally, the different beneficiation methods are compared, and the industrial aspects? of their application are reviewed.

Jan 1, 1990

By Jyothi Rajesh Kumar, Jin-Young Lee

21st century is electronic revolution in human lives as well as energy is one of the most significant tasks. Rare earth elements (REEs) occupy a key role in daily life as well as high-tech industrial applications. REEs are one of the energy critical elements; for sustainable growth, it depends on multiple extraction and separation technologies including solvent extraction and ionic liquid-based extraction methods.

Mar 1, 2017

By I. Gaballah

Decontamination of synthetic solutions of PbC12 containing 10, 100 and 1000 ppm of lead, using chemically treated barks had been studied. The percentage of !cad cations&apos; removal from solutions depends upon the pH and the initial concentration. About 99 % of the initial lead content can be removed at pH of about 3.5, 5.5 and 6.5 for initial concentrations of 10, 100 and 1000 ppm respectively. The maximum retention capacity of the treated bark is about 83 mg of lead per gram of modified bark. Bark loaded with lead had been analyzed by Infra Red spectroscopy. It seems that lead reacts with hydroxyl groups of the phenolic constituents of the bark. On the other hand, the removal of a lead cation by the bark leads to the release of two H+. This seems to show that the removal of lead could be interpreted as an ion exchange with hydrogen belonging to the hydroxyl groups of the modified bark.

Jan 1, 1994

By Frederic Pineau

Semisolid metal alloys have a special microstructure of globular grains suspended in a liquid metal matrix. This particular physical state of the matter can be exploited to produce near-net- shape parts with improved mechanical properties. However, the behavior of the slurry is strongly influenced by the local solid fraction and state of agglomeration. Different flow instabilities ·associated with the combined flow and solidification process result, which make difficult the application of semi-solid processing in the casting industry. Moreover, the rheology of semisolid materials is not well understood. Most of the theory has been derived from experimental data, which are somewhat difficult to measure. A model that accounts for the multiphase nature of semisolid slurries is required to get more insight into such complex flows. This paper describes a mixture model for semisolid slurries. It assumes that the mixture of liquid-solid components behaves as a single fluid as far as overall mass and momentum balances are concerned. The coupling force between the phases is derived on the assumption that the slurry is a fluid saturated isotropic media. The proposed methodology is implemented in a finite element code. The model is then applied to the the filling of an industrial-scale capillary flow viscometer. Segregation patterns are obtained and discussed.

Jan 1, 2001

By J. S. Becker

Technology developed and first implemented in the United Kingdom enables very low grade aluminum scraps containing oils, organics, plastics and ferrous metals to be directly charged, without pretreatment, into a unique melting furnace. The system has been in full scale production for four years. The oxy-fuel-based furnace design incorporates internal afterburning in the furnace&apos;s hot zone, producing excellent thermal efficiency and very low emissions. The furnace is inherently low in NOx. This paper will provide both theoretical background and extensive operating results for this new melting concept. Applications describing both purpose built new furnaces and retrofits of existing reverberatory furnaces will be presented. Extensive operating emissions data will be presented.

Jan 1, 1997

By Heikki Tuovinen

The total utilization of raw materials and energy is the most important criterion when planning. industrial processes. The main goal is clearly to use the raw materials and energy as effectively as possible in order to make the desired products directly in the primary process itself&apos;, or to recycle unused materials and energy either as such, or after cleaning back into the process. However, few industrial processes are so straightforward. Most processes generate by-streams of materials and energy, which cannot be recycled directly and it is namely these by-streams which tend to remain as wastes. These by-streams are slags, dusts, vaporized metals, liquids, slurries, sludges, gases etc. Most base metal processes produce all these by-products. Waste water and gas emission controls and regulations are tightening all the time, so new processes must be developed to keep pace with these requirements. These processes generate more solid wastes, which must be utilized or at least processed into a harmless form landfilling. Municipal and hazardous wastes also contain valuable materials and energy, which must be used to minimize landfilling. The development of processes for these purposes places even greater demands on research and development. The same principles and methods developed for mining, ore dressing and metal refining processes can also be adapted for research and development work on processes for waste minimization. However, the problems encountered are much more complicated and less familiar, demanding more versatile and accurate tools and equipment. This paper presents principles, examples and some references of R & D work on processes for waste minimization.

Jan 1, 1992