Search Documents

By P. Somasundaran

Electrochemical properties of silicate minerals govern their behavior in processes such as flocculation and enhanced oil recovery that can occur at elevated temperatures. Knowledge of these properties as a function of temperature can be helpful in developing an under- standing of the role of these interfacial properties at non-ambient temperatures. Zeta potential of Sodium Kaolinite and quartz has been determined as a function of pH and temperature in this work. Both systems exhibited markedly different behavior at higher temperatures and also exhibited significant hysteresis. Results are examined in terms of possible dissolution of the minerals and surface reactions at different temperatures.

Jan 1, 1986

By R. B. Lantz

Low Froude Number (Fr) theory* predicts that stably-stratified fl& around a terrain obstacle will divide into a lower layer passing essentially horizontally around the obstacle and an upper layer passing essentially over the obstacle. The prediction was formulated by Sheppard (1956) and Drazin (1961) and confirmed experimentally in the towing tank model d experiments of Hunt et a1 (1978) and the atmospheric full scale experiments of the US EPA Complex Terrain Model Development Program (1982- 1985). The US EPA Complex Terrain Dispersion Model, currently under development, employs the layering principle with the flow in each layer calculated independently by potential flow (PF) theory after the layer thicknesses are established according to a simple function of Fr, i.e., Hc /H = 1 - Fr where Hc is the dividing streamline freight and E is the obstacle height. Use of PF theory in the CTDM is attractive because numerical solutions can be obtained simply and economically, as compared to lengthy Navier-Stokes (N-S) solutions, but realism is sacrificed in creating a surface of discontinuity between the tm layers and eliminating the effects of shear and gravity in each layer.

Jan 1, 1986

By Erik S. Bernard

"INTRODUCTION Reinforced Concrete (RC) members such as beams and columns are usually required to include stirrups to maintain post-crack shear capacity, and some may include stirrups that act as confining steel to maintain structural integrity during a seismic event (eg. NZS3101, ACI 318). To achieve seismic resistance, the spacing between stirrups is usually required to be much closer than is ordinarily prescribed for non-seismically resistant structures. Each stirrup must also fully enclose the longitudinal reinforcement with long end-hooks to ensure that the contained concrete is sufficiently restrained during reverse-cycle loading and the reinforcing bars are confined to prevent buckling. The close spacing between stirrups can lead to congestion of reinforcement within members, and can also be expensive to construct due to the labor-intensive nature of steel fixing. A possible alternative to closely-spaced stirrups is the use of fibers to provide restraint and confinement during a seismic event, although this is not yet recognized in codes. Previous experimental research (Jiuru et al, 1992; Filiatrault et al, 1995; Bayasi and Gebman, 2002; Billington and Yoon, 2004) has demonstrated that steel fibers are relatively effective in this application, but suffer the problem that their stiffness can make them difficult to consolidate within an already tight reinforcement cage, especially if they are relatively long (>40 mm). Moreover, steel fiber reinforced concrete (SFRC) is subject to embrittlement with the passage of time, leading to a steady loss of ductility beyond crack widths of 1-2 mm (Banthia and Trottier, 1994; Bernard and Hanke, 2002; Bernard, 2014; Bjontegaard et al, 2014; Bernard, 2015). Since cracks during seismic events are generally much larger than this, embrittlement may present a challenge to the long-term efficacy of SFRC during seismic events. An alternative to steel fibers for enhancement of seismic resistance is the use of macro-synthetic fibers. This type of fiber usually offers the advantage of being flexible so that consolidation is easier between reinforcing bars. They also offer superior durability compared to steel fibers and can reduce flexural crack widths (Bernard, 2016). Several recent small-scale investigations (Ma et al, 2012; Carnovale, 2012; Osorio et al, 2014) have indicated that macro-synthetic fibers can produce meaningful improvements in seismic resistance if used in combination with conventional steel reinforcing bars. The present investigation has extended research in this field by examining whether embossed macro-synthetic fibers can be used to increase the spacing between stirrups while maintaining seismic resistance."

Jan 1, 2016

By F. G. Miller

In mid-1972 we determined that a fresh approach to coal mining research was needed for the industry as well as for Bethlehem. The reasons to us were obvious: Productivity was in the throes of a steady decline, and labor and maintenance costs were spiraling upward. Yet, despite this predicament, nowhere in the U.S. at that time was there a comprehensive and coordinated research and development plan in the offing. The Bureau of Mines had not yet been charged with such a responsibility, and industry was content to rely on machinery manufacturers for innovations. After studying our own mining practices, the state-of-the-art of mining research elsewhere, and development work by manufacturers, we presented a comprehensive research package to our management at the end of 1972. The ideas and experience of many operating and management personnel in our Corporation contributed to the formulation of the final plan as approved.

Jan 1, 1976

By James M. Griffin

Ladies and Gentlemen, There have been no less than ten major coal project financings in the last eighteen months. Each of these has been in the order of $100 million to $1 billion for the development of a coal property and its associated infrastructure. It is appropriate at this time to review the nature of these past financings. Why has there been so much activity? There are primarily two reasons. The first is due to the large number of contracts which were signed as a result of OPEC oil shocks. High projections were made for increased coal consumption particularly in world trade. This is distinct from domestic coal mine/power plant projects which often tap a government source of funds. Second is the high cost of coal development in the 1980's compared with a typical company's corporate borrowing capacity.

Jan 1, 1984

By V. M. Johnston

The most abundant fuel resource in the U.S.A. is also the most under-utilized. Proven reserves of bituminous coal, sub-bituminous and lignite constitute from 60% to 90% of our total fossil fuel reserves -- dependent upon the parameters used by the analyst making the estimate. Despite this ample supply, bituminous coal provided only 20% of U. S. energy consumption in 1967 and 1968, this dropping to 17.57 in 1971 and 1972. By 1978, according to my projections, 16.7% of the Nation's mechanical energy will come from bituminous coal. However, our energy needs are growing at such a rate that the 20.6% provided by bituminous in 1967 equalled 480 million tons while the 16.7% of U. S. consumption visualized for 1978 will require nearly 650 million tons. In order to view coal's position with perspective in this developing energy crunch, it is necessary to examine the total energy situation. To this end, I have prepared a couple of tables which you should have before you. I chose this procedure rather than slides because I would need to utilize an entire wall to make the data visible to an audience. Therefore, I refer you to the long sheet entitled "U. S. Energy Consumption - Trillion Btu - 1967-1978." As you can see from the heading, I am confining my treatment of the problem to the intermediate term. In the long run, if we are willing to pay the cost, we can do a lot of things, including the complete conversion of coal into a sulfur-free fuel.

Jan 1, 1973

By Byron R. Berger

Disseminated Au-As-Hg mineralization is localized along the Getchell Fault system at the Getchell Mine in north-central Nevada. Replacement ore bodies occur in Cambrian carbonaceous limestone and limy shale beds. Cretaceous granodiorite, dacite porphyry, and andesite porphyry dikes parallel the fault zone and are spatially associated with the mineralization. Hydrothermal alteration and mineralization occur continuously along 4-5 km of the fault system, and extend more than 1 km down-dip. Alteration consists primarily of removal of carbonate and deposition of quartz, pyrite, and carbonaceous material. Marcasite, sericite, kaolinite, calcite, barite, and fluorite are common. Gold content reaches more than 43 ppm in parts of the altered zones and averaged 9.3 ppm in the mined ore bodies. For the mineralized zones as a whole arsenic averages 0.28%, and occurs primarily as realgar, orpiment, and arsenopyrite. Mercury (22 ppm) is finely disseminated and mercury-bearing minerals are seldom recognizeable. Accessory mineralization includes antimony (100 ppm), copper (47 ppm) , lead (18 ppm) , molybdenum (10 ppm) , tungsten (16 ppm) , and zinc (50 ppm) . Geologic field studies and K-Ar dating suggest that the mineralization is related to a hydrothermal system produced by the granodiorite and related dikes.

Jan 1, 1975

By D. H. Lynch

Prompted by the need to conserve energy and reduce operating costs, Agrico Mining Company has made two significant improvements in the transportation of phosphate ore from the mine to the beneficiation plant. One improvement involves a change in a slurry pipeline system which substantially reduced pumping energy, and the other improvement is a major innovation for the phosphate mining industry which involves the transportation of the ore by railroad. This paper briefly describes these two projects.

Jan 1, 1981

By M. K. McCarter

In 1963, a major expansion program at Kennecott's Bingham Canyon mine converted rail operation in the upper portion of the pit to truck haulage. Since that time truck-haulage capacity has increased to about 272 000 Mg (300,000 tons) per day. The majority of this production is waste material which is deposited in monolithic dumps located on the eastern slopes of the Oquirrh Mountains. The largest of these dumps, referred to as Copper Notch and Keystone, measures approximately 1830 m (6000 ft) in length, from 180 to 300 m (600 to 1000 ft) in height, and contains some 430 Tg (470 mil lion tons) of waste. The height, structure, rapid rate of growth, and anticipated leaching suggested the possibility of dump failure. In order to evaluate this possibility, an outside consulting firm was retained in 1966 to investigate the stability of the growing dumps. Their investigation indicated that, other than superficial movement, the waste dumps would be stable under static loading, and that soil distribution was not continuous enough to sustain massive foundation failure. Since this investigation, however, several failure processes have been observed. Crest settlement occurs frequently in response to compaction and over-steepening in the upper portion of the dump surface. Over-steepening results from accumulation of fines near the crest caused by natural segregation. Normally, coarse material, near the base of the dump, exhibits an angle of repose near 0.65 rad (37"). The fine material, however, stands as steep as 0.75 rad (40"). Periodic equilibrium adjustments cause stepwise settlement (Figure 1) of the dump surface and occasional sloughing of the protective berm. Routine surface preparation by dozers and graders and frequent inspections by supervisory personnel have proven adequate in preventing problems associated with this form of crest instability.

Jan 1, 1976

By J. H. Field

The sulfur dioxide emitted in low concentrations in flue gases from the combustion of sulfur-containing coals and fuel oils is a significant factor in contamination of the atmosphere with sulfur dioxide. A review of methods for treating gases containing high concentrations of sulfur dioxide shows that they are seldom satisfactory for purifying flue gases. Processes developed specifically for treating flue gases using liquid absorbents are costly and may cause localized pollution, because the cooled flue gases can settle in the vicinity of the stack. Bench-scale research is being conducted to investigate the use of dry absorbents for sulfur dioxide removal at temperature levels of about 250°- 300° F. and 600°-650° F. Alkalized alumina has been found effective for treating simulated flue gas and Is regenerable by hydrogen, carbon monoxide, or producer gas. Other metallic oxides have been tested as absorbents also. Chemically impregnated activated carbons removed sulfur dioxide from the gas at 265° F. Vanadium pentoxide is effective as a catalyst for oxidizing of sulfur dioxide in the simulated flue gas at temperatures lower than have been used commercially for gases with higher concentrations of sulfur dioxide. Conversions of sulfur dioxide to trioxide wore studied as a function of temp- erature over a range of about 570° to 750° F.

Jan 1, 1959

By Naomi H. Harley, Daryl E. Bohning, Isabel M. Fisenne

INTRODUCTION Underground mines in many parts of the world have elevated levels of short-lived 222Rn daughters. Lung cancer implicating exposure to short-lived daughters is documented in the U.S., Czechoslovakia, Canada, Sweden, the U.K., France and Newfoundland. An elevated lung cancer mortality (in excess of that expected) has been observed when cumulative exposure to alpha emitting short-lived 222Rn daughters (218Po, 214pb 214Bi 214Po) is greater than about 60 working level months (WLM) [1]/ (Hewett, D. 1979). This is equal to an absorbed alpha dose of about 30 rads to shallow basal cells in bronchial epithelium. Long-lived alpha emitters are also present in underground mines, and especially uranium mines because of airborne particulates containing uranium. The 238U parent of this primordial series supports other long-lived emitters 234U 230Th, 226Ra, Pb(210Po) which are in some degree of radioactive equilibrium with the parent 238U. Airborne particulates can be present due to drilling on the face of the ore body as well as in all parts of the mine through resuspension from the mine floor. Particles from 1 µm to about 5 µm penetrate the nose with reasonable efficiency and deposit primarily in the tracheobronchial tree. They are removed by ciliary motion (the bronchial escalator) but deliver an alpha dose to basal cells in bronchial epithelium during clearance in the same manner as short-lived 222Rn daughters. It is the purpose of this work to indicate the alpha dose to basal cells in bronchial epithelium delivered by the long-lived emitters 234, 238U. The dose calculations reported here based upon a few measured values of these isotopes in air in uranium mines in New Mexico and Colorado. MEASURED 234, 238U IN URANIUM MINE ATMOSPHERES In 1979, the U.S. Bureau of Mines undertook a study to evaluate personal monitors to be worn by miners to measure short-lived 222Rn daughters. One of these devices sampled air at 100 cm3/min through a 13 mm glass fiber filter, with a small pump worn on the belt. Alpha particles emitted by 222Rn daughters on the filter were measured continuously by a thermoluminescent dosimeter (TLD) chip. Each monitor was worn by a miner for a 170 hour working month and approximately one cubic meter of air was sampled during this period. Six different mines were selected for the test in New Mexico and Colorado. The mines used either wet or dry drilling methods. Miners in each location were equipped with the personal monitors. Subsequent to their use in evaluating the shortlived daughters, Dr. Robert Droullard of the Bureau generously gave us these filter samples along with a few blank glass fiber filters from the same box of filters used in the study so that long-lived emitters present in these mine atmospheres could be determined radiochemically. Four of the samples have been run for 234, 238U. The radiochemical procedure for uranium is adapted from USDOE, Environmental Measurements Laboratory Manual (Harley, J.H., 1976). Briefly, the samples were placed in platinum crucibles, spiked with 232U tracer and pretreated with nitric and hydrofluoric acid. The residue was fused with potassium fluoride to transpose to pyrosulfate. The fused cake was dissolved in 7 [N] hydrochloric acid and the solution passed through an anion exchange column to isolate uranium. Iron was removed using mercury cathode electrolysis. Uranium was electrodeposited onto platinum dies and counted using solid-state alpha spectrometry. The samples from each type of mine (wet and dry) were analyzed. The samples in the "wet" mine in New Mexico were selected on the basis of the original TLD measurement because they were near the maximum occupational standard for radon daughters. These samples should also represent upper limits to longlived activity encountered, since they were obtained at drilling operations on the face of the ore body. Samples collected in the "dry" mine in Colorado were pot associated with a particular location in the mine and should be representative of a month long overall exposure in many locations and operations. The values are shown in Table 1. The two uranium isotopes are in equilibrium and their alpha activity

Jan 1, 1981

By George Innes

The soda ash business in the United States has undergone a sweeping technological change in ihe last 20 years. In a world where synthetics are continuzlly replacing natural products, here we have exactly the opposite, a syntheric chemical being replaced by a natural product. This change is nearly complete in the U.S. and is beginning to take place in Europe and other parts of the world.

Jan 1, 1980

By Roy A. Koski

This paper describes variations in feed characteristics, preparation techniques, response to induration and product quality in pelletizing magnetite concentrates, earthy hematite ore fines, and specular hematite concentrates in grate kiln systems. The Cleveland-Cliffs Iron Company manages plants processing these various materials on the Marquette Iron Range in northern Michigan. The operations include the Humboldt Mining Company, Marquette Iron Mining Company, Empire Iron Mining Company and the Pioneer Pellet Plant. The combined output of the operations is approximately 9,000,000 long tons per year. The Humboldt Mining Company, owned by Ford Motor Company and Cliffs, produces pellets from a specular hematite concentrate. The Empire operation, which processes magnetite ore, is owned by Inland Steel Company, McLouth Steel Corporation, International Harvester and Cliffs. The Pioneer operation, which processes earthy hematite ores, is a joint venture of Republic Steel Corporation, McLouth Steel Corporation, Bethlehem Steel Corporation and Cliffs. The Marquette Iron Mining Company, owned by hones and Laughlin Steel Corporation, International Harvester, Wheeling-Pittsburgh Steel Corporation and Cliffs, produces pellets from specular hematite concentrate at the Republic Mine and Eagle Mills Pellet Plant. With the exception of the Eagle Mills plant, the operations employ the grate-kiln pelletizing system. Descriptions of the Empire, Pioneer and Republic operations, which have a combined capacity of 7,200,000 tons per year, are given in the paper.

Jan 1, 1969

By F. W. Schweitzer

The trend toward development of large low grade ore bodies has accelerated in recent years. It has been estimated within the copper industry that "porphyry" type deposits will provide the bulk of copper production during the next 30 years. It is further estimated that in these deposits the average ore grade by the year 2000 will be 0.25% copper (1). Many of the new porphyry copper discoveries are of such extremely low grade that they are particularly sensitive to small fluctuations in cost variables and copper prices. Because haulage constitutes a major item of surface mining expense, the capability to transport large tonnages of material at increasingly lower unit costs is vital to the profitable operation of many of these mines. High capacity conveyor belts appear to have considerable promise in this area. The heaviest use of high tonnage conveyors has been in the brown coal industry in Germany. In the past 20 years several such installations have proven successful. In addition to the German installations, several other successful systems have been put into operation. Some examples are: The Oroville Dam project in the United States; the tar sand operation in Northwest Canada; the pre-mine stripping and mining of the Twin Buttes Mine in the United States; the Kursk Magnetite 'dine in the U.S.S.R.; and the Nchanga Copper Mine in Zambia. Most of the systems mentioned are handling alluvial material consisting mainly of fines. The noteworthy point regarding these installations is their high continuous capacity. One of the largest lignite mines in the world is at Fortuna, Germany, where over 15,700 tons (15,250mt) per hour of overburden is transported on an 87 inch (221cm) wide belt running, at over 1000 feet (305m) per minute.(2). Another example is a 20,000 ton (18,150mt) per hour system for loading iron ore into barges on the Great Lakes (3).

Jan 1, 1976

By Paul C. Lingo

Two recent antitrust cases, coming from widely separated areas, different industries and involving wholly different facts were decided by the Supreme Court on June 7, 1965. The decisions in these two cases may well prove to be the most important and far-reaching decisions in the field of labor law that have been handed down in the last 24 years. These cases, although quite dissimilar factually, had one common element. In both, the gravamen of the antitrust violation was bottomed on the terms of labor agreements negotiated by a multiemployer group. These cases are usually referred to as Pennington1 and Jewel Teat. Since a number.-of references will be made to the antitrust laws, it may be well to state briefly the applicable portions. Section I of the Sherman Antitrust Act makes "every contract, combination in the form of trust or otherwise, or conspiracy, in restraint of trade or commerce among the several states, or with foreign nations, is declared to be illegal...". Section 2 imposes criminal sanctions against "Every person who shall monopolize, or attempt to monopolize, or combine or conspire with any other person or persons, to monopolize any part of the trade or commerce among the several states...". Under Section 4 of the Clayton Act a person who sustains damages as a result of a violation of the antitrust laws is entitled to recover treble damages plus costs.

Jan 1, 1965

By Z. Rogovin

In order to develop more accurate procedures for scale-up and design of semi-autogenous-grinding mills through detailed mathematical models, a better understanding of the charge motion and rock/ball segregation is needed. To achieve this a 0.61 m (2.0 ft) diameter x 0.305 m (1.0 ft) length plexiglas mill was constructed as a scale model of a commercial SAG mill. Rock motion in the rotating mill was simulated using various sizes of ceramic balls. Quantitative measurements of dynamic angle of repose, water and slurry motion, holdup and size segregation of the charge were taken. In addition, a video-presentaiton (available to the public) was prepared to elucidate charge and water motion at various mill speeds, charge volumes, rock size distribution and flow rates.

Jan 1, 1985

By Jacques LeBel

After a brief definition of asbestos and a review of regulations, the elements of asbestos dust control are outlined for various asbestos manufacturing industries. To prevent the asbestos dust to become airborne, the general procedure is to control the dust at the source by enclosure and exhaustion. The asbestos dust is collected and removed from the air with bag filter collectors of high efficiency (better than 99%) to ensure that the air emitted to the general environment or returned to the workplace are below the existing asbestos emissions regulations. Dust control systems should be regularly inspected and serviced to maintain at all times the efficiency and reliability of the equipment. Other effective procedures for asbestos dust control are also considered.

Jan 1, 1984

By D. B. Sikka

Porphyry type copper ± molybdenum deposits typically occur in the Phanerozoic rocks and have been well documented. During the past two decades a number of porphyry type Cu ± Mo deposits which range in age from 1055 ± 35 Ma to 2970 Ma have been identified in the Precambrian rocks of Australia, Canada, China, Finland, India, Namibia and Zambia. Kalanjkhand porphyry copper deposit M. P., India which is estimated to contain 789 million tonnes averaging 0. 83 percent Cu (millhead-grade); 0.004 percent Mo; 0.2 gm/t Au; 6 gm/t Ag and a cap of 7.532 million tonnes of oxide are averaging 0.8 percent Cu. The economic potential of the expanded copper mining milling, smelting and refining complex to be built in the future at Kalanjkhand, which is the largest porphyry copper deposit discovered to date in the Precambrian rocks of the world is presented.

Jan 1, 1992

By Per H. Fahlstrom

The story of the Aitik mine begins in the early thirties. At that time blocks of low grade chalcopyrite impregnations were found in Swedish Lapland not far from the present mine, some 40 miles north of the arctic circle in the vicinity of the iron ore field at Gällivare. The ore prospect was viewed upon several times. By means of geophysical studies and an extensive diamond drilling programme during the end of the fifties and the beginning of the sixties a huge low grade ore body was discovered under the muskeg overburden. In 1965 55 million tons of ore with 0.5 % Cu was known to a depth of 160 ft. In 1970 the ore reserves had increased to 165 million tons with 0.40 g, Cu at a depth of 400 ft. Decision to develop the mine and to start production at an annual production of 2,2 million tons was made in 1965. A mine and concentrating plant, the A section, went on stream in 1968. In 1970 decision was made to expand the production with 3,3 million tons pr year. A second section of the plant, the B section, went on stream during the end of 1972 and the beginning of 1973 The production in the initial plant has been increased to 3,1 million tons pr year and during 1974 the combined A and B sections are expected to treat' about 7,2 million tons of ore. The two sections will treat 10,000 and 13,000 tons per day.

Jan 1, 1974

By Mo Wanqiang

Equivalent-pressure ventilation is a method of balancing the air pressure between a productive face and its gob to extinguish fires and prevent the infiltration of toxic gases, so that the production of the face can be maintained. The method was successfully applied in Coal Mine No. 1 of Hebi Coal Mining Administration in north-central China. In this article, a practical application of the equivalent-pressure method to prevent carbon monoxide from entering an active longwall face adjacent to a fire breeding area is described, and four steps to achieve equivalent-pressure are discussed. The reliability of using this method and measures to maintain the equivalent-pressure are analyzed. It was observed that this method could maintain high production level while no sacrificing safety at the longwall face.

Jan 1, 1984