Search Documents

By B. E. Davis

A problem that has continued to plague the Florida phosphate industry is the loss of coarse phosphate in the flotation circuit. Attempts to remedy this problem such as floating the coarse material (plus 425 µ m) in a separate circuit have resulted in limited success, but recovery is still not optimum. The Bureau of Mines is investigating ways to improve the recovery of coarse phosphate through improvements in the conditioning step. Studies to optimize conditioning parameters such as agitation energy, conditioning time, conditioner solids, and residual clay content have resulted in improved P2O5 recovery. Optimizing these and other conditioning parameters resulted in a rougher concentrate grading 30 pct P2O5 with a P2O5 recovery of 97 pct.

Jan 1, 1993

By B. Das

Most coals are susceptible to spontaneous heating which in turn creates problem to mining, storage and transportation of coal. It is impossible in actual practice o eliminate spontaneous heating but spontaneous combustion can effecively be controlled through a clear understanding of its mechanism and the factors affecting it. There are altogether six stages in the process of spontaneous combustion. This includes the water adsorption stage and six oxidation stages: chemi-sorption (upto 70°C), decomposition of peroxygens (70°C-150°C), oxy-coal formation (150°C-230°C), combustion initiation (230°C) and active combustion (> 230°C). Heat is produced in all these stages. On the other hand heat is also dissipated so that some equilibrium temperature is reached. If this temperature exceeds a certain critical value (generally about 70°C), coal oxidation may advance to spontaneous combustion. The major factors influencing spontaneous combustion of coal are: coal rank, maceral composition,, water, mineral matter, joints and fissures, seam depth and thickness, mine Layout, method of ventilation, etc. Susceptibility is high for low rank coals and generally decreases with increase in rank. Of the macerals, the exinites are generally most susceptible, the inertinites least and the vitrinites somewhere in between. Water plays a major role on the spontaneous heating of coal, assisting in someways and inhibiting in other. Unrecovered coal in the gob (generally in thick seams) is a major source of fire hazards and this is specially important in shallow mine. Proper design of mine ventilation system can substantially reduce the risk of mine fire. Panel layout and load transfer can affect the development of induced cracks which in turn influence spontaneous heating. Finally, the difference between the spontaneous heating of coal in a seam and that in storage or transportation is mainly due to the change in moistured content, air circulation through the coal and coal fragmentation. These aspects have been analyzed in this paper with a view o reducing the risk of spontaneous combustion.

Jan 1, 1986

By S. Shankar

The phenomenon of re-entrainment is seen in many environments, such as sand dune formation, soil erosion, fugitive dust emission, spread of radio-nuclides from accidents involving nuclear weapons, etc. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of on-going research in the Respirable Dust Center on the prediction of ambient dust concentrations in mine atmospheres (Ramani, 1983) to identify the contribution of dust re-entrainment to the spatial and temporal concentration in mine airways and included wind tunnel and in-mine studies. A set of seven experiments was performed in the Lake Lynn Laboratory Mine of the U.S. Bureau of Mines under controlled conditions. Two types of source coal dust, anthracite and bituminous, were subjected to airflow with a range of air velocities and walking by two different walkers. Six sets of instruments were used along the test section for sampling the airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/s. Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg/m3 (standard deviation = 0.03 mg/m3) from an initial value of 0.02 mg/m3. The concentration of all (i.e., total) airborne dust increased to 0.17 mg/m' (standard deviation = 0.10 mg/m') from an initial value of 0.02 mg/m'. The action of personnel walking, however, caused higher amounts of re-entrainment. Average concentration of respirable and total dust at the center of the mine airway increased to values of 0.28 mg/m' (standard deviation = 0.12 mg/m3) and 1.53 mg/m3 (standard deviation = 1.0 mg/m3), from initial values of 0.03 mg/m3 and 0.05 mg/m3, respectively. It was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal dust bed. Depending on the level of activity and the amount of dust deposited in mine airways, re-entrainment may become an important source of airborne dust away from the point of actual mining.

Jan 1, 1994

By Ulrich Maidl, Gustavo Aguiar, Argemiro Ferreira, Marco A. Peixoto Silva, Marc Comulada

"Metro Line 5 in Sao Paulo is being constructed. This lot extends for 4,940 m with twin EPB shield tunnels under a dense and busy urban area, with an excavation diameter of 6.9 m. The tunnels run predominantly in the tertiary soils of Sao Paulo where extensive experience exists from previous EPB shield tunnel projects. However, new experience is being gained in Sao Paulo in shield tunnelling through Saprolite, the weathered product of the underlying Gneiss crystalline basement, through the resulting residual soils and in rock-soil mixed face conditions. Furthermore, experiences in difficult mixed face soil conditions with overconsolidated clay at the face in combination with loose sands at the crown under the groundwater table will be presented. Additionally, the design, operational and controlling approach followed for the shield drive at particular critical cross-sections where the shields were driven close or under buildings. INTRODUCTION Within the framework of Sao Paulo´s metro network expansion, the excavation of the shield tunnels for Metro Sao Paulo Line 5 is currently taking place. The present paper deals with the description of the most relevant features from the construction of the Line 5 – Lot 3 tunnels. The paper presents how particular challenges were dealt maximising potential of EPB shield tunnelling technology. Challenges were posed not only by the difficult boundary conditions of urban shield tunnelling, such as shield drive under buildings, but also by complex geotechnical situations. PROJECT DESCRIPTION The great urban area of São Paulo is one of the biggest cities in the world, with around 20 Million people living in the city and in the suburb area. The city faces great mobility problems and in the last years the government has been investing great amounts on the megacity´s metro expansion. The Line 5 Extension plays an important role to connect the south area to the central area of the city, with a whole extension of 11 kilometres, including 11 new stations. It is estimated that this line will transport almost 900.000 passengers/day. The first stretch of the expansion, Lot 3, consists of two single tunnels, almost 5 kilometres long each, crossing 4 stations. Figure 1 shows details of the Line 5 Expansion."

Jan 1, 2016

By David Butts

Solar ponding to crystdlize sodium chloride has been used for thousands of years.1 The systems used were inefficient and usually small compared to the large 25,000 acre pond areas seen today. It has only been in the last 25 years that any real effort has been applied to develop solar ponding technology. Many large solar pond systems have been constructed without much thought to efficient and optimum production rates. The recent high costs of labor, of equipment and of energy have forced producers to take a closer look at their solar pond systems in an attempt to squeeze out the highest possible yields. Other companies such as the Arab Potash Company, the Dead Sea Works, Texas Gulf (Moab, Utah) and San Francisco Salt Companies have no more land area in which to expand and therefore efficient ponds are essential. This paper is written to show how the subdivision of solar ponds can result in production increases of up to 20% and beyond.

Jan 1, 1984

By M. M. Carpenter

Specialty chemicals are widely used in the industrial minerals process industry for many different purposes including beneficiation, filtration, flocculation, dispersion and biological control. Optimal use of such chemicals can confer benefits both in terms of cost efficiency and end product attributes. In this paper we will review recent progress in the fundamental understanding of mineral additive interactions and present data which show how optimization can lead to improved products.

Jan 1, 1999

By R. Pixler

Arch Mineral Corporation and Rocky Mountain Energy's Medicine Bow Mine in Wyoming presented an interesting challenge to the concept of mining a multiple-seam, dipping coal in the Hanna Basin. The 3362 and 2962 pits at MBCC were designed in a multiple seam coal consisting of 4 (and in some areas 5) bands of coal; these coal beds are all in the Ferris formation. The area was subject to some localized faulting and a major fault caused a physical restraint that we mined up against in our final cut. Using a 1570 dragline as the principal stripping machine, the concept of developing a bench for stripping the lower seams from the low-wall side of the pit was initiated. The results of this method of stripping were very satisfying for this pit through the completion of pit life and prompted us to use it in other areas at MBCC and at our other operations. Mining a dipping coal presents a small twist to conventional "flat" coal stripping. The spoil has a tendency to continually try to slide into the pit and the increased overburden on each cut as you mine down the dip creates spoil problems unless adequate design provisions are made prior to stripping.

Jan 1, 1986

The extraction and recovery of gold from copper electrorefining slimes by leaching and solvent extraction using dibutyl carbitol (DBC) has been practiced for several decades. Yet, the deportment of some common elements in this process has not been reported. The focus of this paper is to report the behavior of copper, bismuth, silver and selenium during the processing of industrial solutions by batch and continuous extraction on the laboratory scale. It was found that DBC, while an excellent extractor of gold from a highly oxidative chloride leach solution, also loads significant quantities of Cu, Bi, and Se. Silver was not present in significant quantities in the leach solution nor did it load appreciably. The deportment of gold and impurities are reported for batch and continuous operations of a two-stage extraction process using distribution ratios and separation factors.

Jan 1, 2010

By M. R. Shahan, W. R. Reed

A laboratory apparatus (shield dust simulator) was designed and constructed to simulate the dust generated during the advance of longwall hydraulic roof supports, or shields. The objective of the study was to develop a tool that could be used to test the hypothesis that foam applied to a mine roof prior to a shield advance could be used to reduce the respirable dust generated during shield advances. This paper will outline the design parameters for the development of the system, as well as describe baseline testing of coal and limestone dust. Results show the average instantaneous respirable dust concentrations that occurred during simulated shield advance. Confidence intervals were calculated from the instantaneous respirable dust data to determine the repeatability of the data produced by the device. INTRODUCTION During longwall mining, miners can be exposed to respirable dust that is generated during the advance of hydraulic roof supports or shields. National Institute for Occupational Safety and Health (NIOSH) researchers have conducted numerous surveys of longwall mining operations, benchmarking the operating practices and dust control measures in use. It has been determined that the shields are responsible for 27% of the respirable dust that is generated on the longwall face [1]. The dust generated by the shield advances ranks second, next to the longwall shearer which is accountable for 43% of the respirable dust generated on the longwall face. The respirable dust generated during the advance of the shields can be a significant contributor to the respirable dust exposure of the mining personnel operating at the longwall face, especially since some of this dust is generated in the walkway. Control systems designed to reduce the dust levels generated during the shield advance have the potential to greatly reduce the respirable dust exposures of the personnel downwind of these activities. One control technology to decrease the dust generated by the shield advances would be to apply a layer of foam to the forward shield-roof interface prior to the shield advance [2]. The blanketed layer of foam would interact with the material located on the top of the shield during the advance, preventing a portion of that dust from becoming entrained in the mine air. This layer of foam would be applied using a foaming nozzle located on the longwall shearer body that would spray foam on the roof surface as the shearer passed. Substantial laboratory work has been completed to determine the feasibility of this type of foam application. NIOSH engineers have classified the various characteristics of foaming agents, using foam expansion ratio and drainage as important properties, as well as developed the mechanical systems required to apply the foam safely to the mine roof [2, 3]. The construction of an apparatus that could simulate the mechanical interaction between the dust-laden shield top and mine roof was necessary to adequately test the hypothesis that foam could be an appropriate control. A team of engineers designed and constructed a shield dust simulator system allowing for in-house testing prior to a full-scale field investigation.

Jan 1, 2019

By Roger N. Miller

Talc mining in Vermont has in recent years undergone a progressive change in mining methods and in mining equipment. Underground mines have been phased out except in special circum- stances, and continuous mining machines (CMM?s) have replaced conventional drill/blast mining systems. Talc mining in Vermont began in the late 1800?s, and has continued without interruption to date. Beneficiation (flotation) has been applied since the early 1930?s, and has provided special products for toiletries and other markets. At the present time, there are two active companies that have evolved from the cumulative absorption of nearly ten smaller operations.

Jan 1, 1984

By B. L. Bobo

To ensure the continued growth and economic viability of the Western coal industry, both in the domestic and inter- national markets, it is essential for the industry to become more creative and active in confronting the most serious obstacle in this objective; and that is, the inherently long distances which Western coal must be transported inland to reach its major markets. Figure 1 shows the 1982 coal consumption by state for those states where Western coal was consumed. (Except as noted in this paper, Western coal producing states are defined as Colorado, New Mexico, Arizona, Utah, Wyoming, Montana and North Dakota. Any exceptions used will have only an insignificant effect on the content of the paper). This figure illustrates the long distances that are required for Western coal to reach its markets. The total production for 1982 from the Western coal producing states was approximately 220 million tons, of which only 85 million tons was consumed within the boundaries of these states. The remainder was transported to markets outside the area. This map also shows, based strictly on the consumption of the states to which Western coal was shipped during 1982 and not considering other factors which are involved in the marketing of coal, the total market potential of Western coal would amount to a total of 445 million tons. This does not include export coal from the West Coast, which is now estimated to be less than 2 million tons for 1983. In 1980, it had been estimated that by 1985 the West Coast exports would have been at least 10 million tons per year, which will not be attained.

Jan 1, 1983

By Mark H. Johns

Leaching of waste material at Kennecott's Chino Mines Division at Santa Rita, New Mexico, has been accompanied by increasing difficulty in circulating leach solutions through the dumps. As a means of recognizing existing problems and considering alternative applications of the leaching concept, a leaching research program was proposed which could be applied to a specific, typical waste dump. Conclusions derived from the area could then be applied to other leaching areas at Chino. Associated with the program was an evaluation of the physical characteristics of the area using Chino's drilling and radiation logging techniques.

Jan 1, 1970

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By Donald G. Foot

The Bureau of Mines, U.S. Department of the Interior, devised a direct flotation method for treating low-grade carnallice (KC1.MgC12. 6H20) and sylvinite (a mixture of KC1 and NaC1) ores characterized by a high content of water-insoluble impurities. The procedure consists of (1) flocculation-depression of the insoluble slimes, (2) decomposition leach (carnallite only), (3) potash rougher, cleaner and recleaner flotation, and (4) final product leaching. The technique eliminates the necessity of removing the water-insoluble slimes by mechanical or flotation desliming. Laboratory results demonstrated that the direct flotation procedure, when compared with conventional techniques, yielded equivalent or improved flotation results with equal or less reagent consumptions. The direct flotation method recovered 81.6% of the solid-phase KC1 from carnallite ore and 79.7% of the KC1 from sylvinite ore in final products containing 60.5% and 60.9% K20, respectively. A flowsheet incorporating the described flotation procedure is presented.

Jan 1, 1981

By C. W. Armbrust

At FHC Gold Company's Paradise Peak Mine gold and silver are produced. Precious metals recovery rates are very satisfactory along with the recovery and production of a relative high volume of mercury. At Paradise Peak precious metals are recovered via the Merrill-Crowe process and delivered to the refinery area as a mercury-bearing precipitate cake. The recovery of mercury is then obtained through a vacuum retort system. The balance of the material is mixed with fluxes and then melted and cast into dore' bars for shipping. Issues of retort capacity and concerns over efficiency led to research into the retort process itself.

Jan 1, 1990

By Clifford R. Porter

A 200 pound per hour Magnex Pilot Plant was designed and constructed. A non-compliance Eastern Coal which would generate more than 2.0 lb of SOZ per million Btu upon burning was brought into compliance (less than 1.2 lb of S02 per million Btu) during continuous operation of the pilot plant. Approximately 85 percent of the pyritic sulfur was removed while recovering 86 percent of the Btu of the feed coal. Pilot plant operation is summarized and preliminary economics presented. Present status of the Magnex Program is reviewed.

Jan 1, 1977

By R. R. Young

Good afternoon gentlemen. It is always a pleasure to talk about a subject dear to our hearts--the high speed transfer of bull; materials. Specifically, today we will be reviewing the engineering approach to an age old problem of ship loading and unloading. You may be puzzled by the title of this paper and we will attempt to explain this for you--particularly the use of the words "New Era", since high speed automated facilities are nothing new to the material handling engineer. The new era in material handling designs refers to an all out concerted effort to provide custom engineering tailored to specific operations and economic requirements of the client. It shuns hardware type of engineering wherein existing machines and devices are dusted off and reapplied. It provides automation when automation can be justified and it exemplifies the application of systems engineering to solve specific problems.

Jan 1, 1967

By John M. Gullbert

It is the task of this portion of today's session on the new meaning of regional tectonics in the search for ore districts to discuss known interactions of tectonics and ore deposition in the 'new global tectonics' context. I will speak particularly about known applications of the recent tectonic advances to ore finding. Stated yet another way, it's getting on in time toward the "put up or shut up" stage-¬and I would not be here if I thought that the new tectonics were not an effective present matrix for ore finding. Before delving into specific geologic relationships--and I propose to discuss mainly the evolution of an idea which may reveal the presence of a major copper deposit on mainland Mexico--I must note that there have been no published accounts that I know of which assert that a particular discovery has been made soley and specifically because of an interpretation based upon mechanisms directly linked to sea floor spreading or plate tectonics. It is nonetheless true" that several major exploration efforts are based upon such interpretations, and, as is normal when exploration ideas are involved, one does not wish to call attention to an advantageous position in a highly competitive business. Little might be expected to have been announced in so fast-moving and potentially lucrative an area. Another point which needs to be made is that people such as B. S. Butler (1933), Billingsley and Locke (1935 and 1941), Harrison Schmitt (1935), and more recently Mayo (1958) have been working for decades with the tectonic expressions of the emergent tectonics without recog¬nition of the driving forces or the unifying tectonic concepts

Jan 1, 1971

By D. Brabec

One of the analytical problems in exploration geochemistry is the choice of a method of sample attack which would be rapid, simple and reliable in terms of precision and discrimination between different concentration levels of elements sought. The wet sample attacks currently used in analysis of silicate rocks vary from total decomposition to leaching by weak extractants. The total decomposition of such materials is usually achieved either by alkaline fusion or hydrofluoric acid attack. The first method requires the use of platinum vessels which is both expensive and slow for batch operation. The second type of attack is more widely applied in rock geochemistry1, but it is still relatively slow for exploration purposes and requires extra care (especially when hydrofluoric acid is used in mixture with perchloric acid). Considerable improvement in speed can be achieved by using the sample attacks which release only part of the metal present in a rock.2,4 One of such attacks is the leaching of pulverized rocks by hot aqua regia.3 Another technique widely used in geochemical prospecting involves fusion of the samples with potassium pyrosulfate (or bisulfate) followed by an acid leach of the malt .5 One of the advantages of these techniques is the use of glassware in decomposition stage which considerably increases the analytical productivity. It should be noted that partial chemical attacks tend to extract from a rock mainly the non-silicate metal which may give results more significant for exploration purposes than the analysis for total metal.

Jan 1, 1970

By Fredy A. Elorrieta Agramonte, Gabriel von Rickenbach, Roberto Luis Fonseca, David Córdova Rojas, Rolando Romero, Rico Brändle

The mine’s economic life is dynamic by nature. Some factors that create this scenario are the need to recognize new exploitation areas, the evolution of the mineral prices and the development of new technologies to access them. The dynamics of mining development, especially in the underground environment, changes significantly as the stages unfold. In many cases the final solution differs greatly with the initial. The frequent presence of new conditions and factors often cause the mine to develop in a quasi-permanent transition stage, which could be characterized by the generation of dynamic micro-seismic events that could cause rockburst damage in some specific areas. Although they may be infrequent, these dynamic events can have an important adverse impact on mine safety and causes serious losses. Also, changes in the production schedule during exploitation could be a big issue if the problem is not effectively addressed. When the transition of the mine to an active micro-seismic environment begins as an unforeseen scenario, it is frequent to use static ground support systems as they are readily available. Traditionally, the support systems used are reinforced shotcrete with a middle layer of Welded Standard Wire Mesh (WSWM) and Chain Link Standard Wire Mesh (CSWM) of reduced gauges, i.e. wires less or equal than 4 mm in diameter. Although, this support system is used to control static instability problems, there is no good reference of its energy absorption capacity under dynamic load conditions, creating uncertainty in the effectiveness of controlling rockburst events. These support systems are analyzed at the present paper, testing the reinforced shotcrete layer with 4 mm diameter of WSWM and CSWN under dynamic load. Additionally, the influence of the use of high tensile strength steel wire in the meshes (HSWM) compared to the previous ones, is analyzed to assess the scope in controlling rockburst events and keeping the safety of underground environment.

Apr 26, 2022