Search Documents

By Jerome A. Westphal

The Middle Mississippi River extends from the mouth of the Ohio River to the mouth of the Missouri River, a distance of about 310 kilometers (km) measured along the river. From its founding in 1764 to the first steamboat arrival in 1817, the City of St. Louis was little more than a trading post. However, with the advent of the shallow-draft steamboat, the Middle Mississippi River rapidly became a major thoroughfare of commerce. In this regard, its importance has been reflected by the development of port facilities at St. Louis and by Federal activity relating to channel maintenance and improvement. First Federal work on the Middle Mississippi River was autho¬rized by Congress in 1824. This work was for snag removal and bank clearing and was directed at reducing the hazards to steamboat traffic, particularly during low-flow periods. During the 1820's and early 1830's, the main channel threatened to move toward the Illinois shore and abandon the St. Louis port facilities. In 1836 and 1837, Congress authorized construction of permanent improvements to keep-the river next to St. Louis (Missouri shore). By 1880, it was recognized that bank clearing activities had resulted in a wider and shallower river which exacerbated navigation

Jan 1, 1977

By James A. Decker

Hanna has developed three production planning systems to help the mine engineers determine the sequence of mining from available ore supples. The Production Scheduling System was developed to give the staff a tool for long range planning by sequencing the removal of blocks from an open pit property. It was needed to determine the year of removal for each block so that the optimum present-valued pit limits could be established by our pit design program. Since in this type of planning short term grade control is less of a factor than it is in daily or monthly planning, the system gives the program greater control and more latitude in block selection. It permits only full blocks to be taken.

Jan 1, 1984

By Behzad Khorshidi

"The ultimate objectives of the post-tensioned strands are to connect the precast segments into a ring and provide pre-stress in the tunnel circumference. The method involves inserting the strand through the preliminary embedded duct in the precast concrete segments and then tensioning the strand by jack and fastening it. The post-tensioned strand eliminates the necessity of bolt connections between the segments and may reduce the labor cost and increase speed of lining construction. Pre-stressing of the segmental lining reduces the steel reinforcement or fiber volume in precast segments and/or thickness of the precast segments which would result in reducing the manufacturing cost of them. Pre-stressing would reduce cracking and increase water tightness, and would provide smooth intrados due to eliminated bolt joints and pockets in the tunnel lining. Pre-stressing would increase resistance to internal pressures as well. Further, this system could work very well structurally in tunnels with squeezing rock or tunnels with high seismic loadings. INTRODUCTION OF THE METHODPost-tensioning is commonly used in the construction of bridges, large buildings, nuclear power stations, and water tanks but its utilization in tunnels is still in its infancy.The precast pre-stressed concrete segmental lining can be used for shield tunnels. It provides a reinforced lining ring by the following construction stages and as shown in Figure 1:1) Segments to be assembled by TBM to complete a full ring2) Steel strand to be inserted through embedded duct (sheath) within the segments3) The strand to be tensioned by Jack after anchorage of the other end4) The strand to be fastened after reaching required tension load5) The horizontal strands (if necessary) to be installed, tensioned and fastened6) The recesses and gap between strand and duct to be filled by groutingFurther, Figure 2 shows an unbonded post-tensioning strand model; Figure 3 shows an anchor sample (Xanchor); Figure 4 shows a duct (sheath) and anchor within reinforcement; Figure 5 depicts the posttensioning of a strand by jack; and Figure 6 is an image of the Midorigaoka Trunk line tunnel in Sagamihara, Japan which was constructed using this system."

Jan 1, 2016

By George C. Hawley

Historically, mica usage has been low because of limited availability; as a by-product of many small processors, who have lacked motivation for extensive R & D. The discovery of a 30 million ton deposit of 85-90% pure phlogopite, when existing markets are only 300,000 tonnes annually, forced the search for large volume new markets. Increasing costs of energy, petrochemicals, plastics and glass fibers, and environmental constraints on asbestos usage, have led to new opportunities for mica as a reinforcing filler. Extensive research and developments; in beneficiating, processing and treating mica, has been necessary to satisfy these new markets.

Jan 1, 1981

By Donald E. Zipperian

It has been recognized that froth flotation of mineral particles utilizing rising flow of micro size air bubbles, counter-current to quiescent falling flow of particles in a column type cell, provides a unique mechanical atmosphere conducive to extension of froth flotation process to much coarser and finer particles sizes than possible with mechanically agitated and aerated cells. 1,2,3,4. This paper describes metallurgical results obtained at several plant installations of large capacity commercial size Deister FLOTAIRE® Column Flotation Cells. These cells utilize air aspiration into surface tension lowered water to generate micro size bubbles. Operating costs, power, wear, and scaling characteristics of rougher, cleaner, and scavenger units are compared with mechanical units. Problems encountered and scale up criteria developed when increasing from 0.20m(8inch) diameter pilot cells to 2.42m(96inch) commercial cells are discussed.

Jan 1, 1985

By J. Kang

Supercritical fluid extraction (SFE) has became an attractive alternative technology to be a new process to recover metal, of which can be substitute the existing Leaching/Solvent extraction processes. Solvent extraction of metallic ions is a technically important and also well-established process that is used in the chemical and hydrometallurgical industries.1 Solvent extraction techniques use the chelation of metallic ions dissolved in liquid solution with organic ligands. Conventional solvent-extraction technique needs large amount of organic solvents and often creates environmental problems.2 More environment-friendly technology is needed nowadays, and there have been increasing attentions to extract metal ions by SFE. CO2 becomes one of the most notable alternative organic solvents due to its nonflammable, nontoxic, nonpolluting, and relatively inexpensive properties with its moderate critical point (73.8 bar, 31.06 °C). Many works have been reported in metal extraction under the supercritical CO2 (scCO2) solvent.3-5 In this study, to recover cobalt from wastes especially from spent lithium ion battery scrap, we selected two ligands ? Cyanex 272 and DEA (diethylamine) for the metal extraction in scCO2. Cyanex 272 is a commercially available extractant along with its series, Cyanex 301 and Cyanex 302. Smart and coauthors measured the metal extracting abilities of these three extractants, and found that Cyanex 301 and Cyanex 302 extracted metal ions much better than Cyanex 272 in the scCO2 solvent.10 The pH of water contacted with high pressure CO2 (70-200 bar, 25-70 oC) is about 2.8-2.95 based on the calculation and the measurement.6-7 Cyanex 272 is known to be less effective as a metal extractant in this low pH environment compared with other Cyanex series. However, when DEA is added to metal extraction reaction with Cyanex-272, DEA works as a strong base to Cyanex 272 converting Cyanex 272 to a deprotonated form (Figure 1), which results in an easy formation of metal complex and the enhanced extraction rate of metal ion.8 Therefore, the purpose of this paper is the metal extraction from spent lithium ion battery waste using scCO2 with Cyanex 272 and DEA.

Jan 1, 2010

By P. W. King

The performance of the versatile McNally Wedag horizontal vibratory centrifuge for dewatering ultra fine 0.5 x 0.15 mm (28 x 100 mesh) material has proven to be success¬ful and the results presented herein will examine its capabilities in terms of capacity, solids capture, product moisture, effluent solids, and size analysis. Centrifugal dewatering of fine refuse has proven t to be another application for which this unit has performed exceptionally well.

Jan 1, 1985

By R. Eggert

Since the discovery of high temperature superconductors has led to extensive interest and conjecture regarding their potential to change contemporary technology, discussions of the impact on the metallurgical and other industries have naturally arisen. In this paper we present data showing the possible impact of these developments on the materials related to the fabrication and proliferation of devices based on superconductor materials. We observe that the largest volume of effort with LTSC will be for the demonstration of high power devices while applied research relating to processing will remain the principal HTSC activity. We also note that in the next decade copper consumption in the US is expected to remain essentially at the current level while the need for Nb and Sn,; two major components of LTSC, will grow at a faster rate both in the US and the world. Although the use of superconductor-based magnetic separation is anticipated to increase, no major impact of these components on the metallurgical industries is expected.

Jan 1, 1990

By George L. Atwood

The Monsanto Company's Henry Mine is located 17 miles northeast of Soda Springs, in the southeast corner of Idaho. Ore being mined is phosphate rock which lies in the Permian Phosphoria formation. The ore is the raw material for Monsanto's three furnace elemental "P" plant near Soda Springs. The finished product from the furnaces is elemental phosphorus which is subsequently used in the manufacture of detergents, food preservatives, fire retardants and other consumer items. Mining is by open pit methods using 0-9 crawler tractors to rip and push-load rubber tired scrapers in stripping and mining operations. The equipment spread consists of six D-9G crawler tractors, four Caterpillar 6578 scrapers, eight Euclid S-24 scrapers, one Reich T750 drill and one Caterpillar No. 16 patrol plus various support equipment. Stripping is performed on a 12-month basis, two shifts per day. Mining is performed mainly in the summer months on a one shift basis. The hauling season begins May 15 and ends November 1 due to freezing weather and snow conditions. Annual production is 1,000,000 tons of phosphate rock and 2,500,000 to 3,000,000 yards of stripping. Stripping, mining and hauling is performed for Monsanto by Dravo-Soda Springs, a mining contractor. Dravo-Soda Springs owns, operates and maintains all equipment used in stripping, mining and hauling. The contractor is paid for stripping by the bank yard and for ore mined and hauled on a tonnage basis. The Monsanto elemental phosphorus plant began production in 1952 with ore being trucked to the plant from the Ballard Mine. Haulage was over public roads in 15, 24-ton semitrucks. A private haul road was constructed from the Ballard Mine to the Monsanto Plant in 1958 and 1959 to accommodate trucks with two twenty-yard trailers. This 11/ mile road was first used in the 1959 hauling season. In 1965, five new Kenworth tractors with two, 'forty yard trailers were introduced into the haulage system. These units carried 120 ton payloads and were used until

Jan 1, 1972

By Leonidio Stegmiller

Since the petroleum crisis in 1973, charcoal1 is being considered one of the most important fuel for the Brazilian consumers, mainly for pellet's producers. In replacing fuel by charcoal mixed up with ore, obviously one of the first thing to be investigated is its influence in the product's quality. Special attention has been given to the metallurgical characteristics. This paper infocus the effect of increasing dosings of charcoal to the pellet's porosity and how other physical and metallurgical characteristics will be affected accordingly. This work was carried out using two different finesses of charcoal and dosing varied from 0.5 to 2.0%.

Jan 1, 1982

By R. C. Freas

The physical and chemical properties of mica are unique relative to most other industrial minerals. As such, mica is suitable for a variety of functional applications in new and emerging markets. This paper examines some of these applications and particularly the contribution mica makes in end product performance.

Jan 1, 1997

By F. J. Murrell

No other region of the world is enjoying the tremendous growth of power use that is currently being experienced in Asia. Fortunately for those of us in the coal industry -particularly in Asia -the preponderance of the power plants being planned or under construction designed to use coal as the power plant fuel. This has produced a significant increase in the demand for steam coal, which has in turn encouraged many of us in the industry to develop new coal mines. One country that has enjoyed very substantial growth in coal production is Indonesia. This developing country of 195,000,000 people who live on the nearly 13,000 islands of Indonesia have emerged very quickly to become the third largest exporter of steam coal, following only Australia and South Africa. Almost all coal in Indonesia is mined by surface mining methods. This paper will examine the surface mining of coal in Indonesia, as it continues to be an important part of the supply equation for coal in Asia.

Jan 1, 1996

By R. K. Mehta

Stirred ball mill feed used for ultra-fine grinding application requires fine size separation step in order to avoid over-grinding. This paper presents the selectivity curves obtained for oil shale and complex sulfide are using 460 mesh (30 micron) Derrick vibrating screen. Interestingly, the selectivity curves generated from the experimental data were monotonic increasing selectivity for oil shale but not monotonic increasing for sulfide ore. These non-monotonic increasing selectivity curves were similar to the mechanical air separator fishhook selectivity curves described by Luckie and Austin. A 2 stage classification in series model describing the fishhook selectivity curve has been used in proposing the classification mechanism for fine vibrating screens when heterogeneous multicomponent sulfide are undergoes size separation.

Jan 1, 1992

By R. K. Will

An inactive mining operation in northern California is known to be a source of acid mine drainage and heavy metals which have impacted adjacent creeks. Elevated concentrations of copper and zinc are a concern to aquatic populations, particularly steelhead trout and salmon downstream in the Sacramento River. Previous regional geological surveys of mineralization by the U.S. Geological Survey located and mapped outcrops of massive sulfides and gossan. Recent investigations indicate that a substantial amount of the metals in the local creeks are due to natural causes. The investigations include locating and mapping surface and subsurface minerals, soil and water sampling, and chemical analysis. Groundwater, seeps, and surface water were also sampled and analyzed. A water balance was conducted on a sub-basin level following delineation of surface water drainage and groundwater divides. A chemical mass balance incorporated metal concentrations and water volumes and was then used with other data to determine the contribution of metals from natural versus mining-related causes.

Jan 1, 1998

By W. A. McKinney

The U.S. Bureau of Mines, Kennecott Copper Corp., and New Mexico Institute of Mining and Technology are cooperating on a research project to improve extraction of copper from previously leached waste dumps that are in part compacted and impervious to leach solutions. The field work is being done at the "J" leach dump, Chino Mines Division, Kennecott Copper Corp., Santa Rita, N. Mex. The laboratory percolation leaching tests were made at the U.S. Bureau of Mines Salt Lake City Metallurgy Research Center on drill core samples from the "J" dump to determine how much copper might be leached if permeability could be restored by explosive heaving or other means. The core samples from nine drill holes on "J" dump contained from 0.06 to 0.14 percent copper. Copper extractions ranging from 15 to 3 percent were obtained in 75 days by percolation leaching of minus-1-inch material with dilute sulfuric acid. The tests results indicate that about 2'7 percent of the copper remaining in the "J" dump could be extracted under ideal leaching conditions.

Jan 1, 1970

By T. Guler

Turkey has important celestite reserves in Sivas. These reserves have gypsum and/or calcite as gangue minerals. Celestite-calcite ore cannot be concentrated by gravity methods due to the low efficiency of gravity methods in fine sizes. Research was tried to concentrate celestite to a market grade by flotation. Parameters such as pH, particle size, dosage and types of collector and depressant were examined. Cyanamid A-845 and Na-oleate combination as collector, sodium silicate as depressant, and Aerofroth-65 as frother were found as the optimum flotation reagents. By applying 3-stage cleaning, a concentrate assaying 95,34 % SrS04 was obtained with 84,93 % recovery.

Jan 1, 1999

By Robert Moore Lewis

Extensive exploration is being undertaken throughout the world in search for heavy minerals, particularly rutile and other titanium minerals. The federal government is sponsoring research involving rutile ores and recovery of stockpile-grade concentrates from domestic sources. Producers are being forced to turn to deposits with a heavy mineral content as low as 0.50% (essentially rutile and zircon). The North Carolina State University Minerals Research Laboratory investigated the possibilities of recovering heavy minerals from the amine tailings of the Texasgulf Inc.'s phosphate plant at Aurora, North Carolina. One laboratory beneficiation procedure using gravity, electrostatic and magnetic processes, resulted in the recovery of 78.7% of the heavy minerals in the amine tailings. Based on this percentage recovery and the present rate of phosphate mining, approximately 13,000 tons per year of heavy minerals (principally ilmenite and zircon) with a potential value of approximately $1,045,000 (1977) could be recovered. The economic potential for recovery of these heavy minerals appears to be favorable. A flotation procedure for up-grading the heavy minerals content in the amine tailings has been developed at the Laboratory, which could allow for concentration of heavy minerals and storing them in tailings area other than main tailings for future processing.

Jan 1, 1978

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sulfur) coal which may be mined when the better deposits are depleted.

Jan 1, 1997

By M. L. Smith

SAG mill throughput is often a bottleneck in increasing metal productivity. Improved size distribution control in the mill feed can be used to increase mill production. This can be accomplished by controlling blast fragmentation as a function of energy input and rock characteristics. Such an approach requires the integration of rock fragmentation and comminution modeling. The optimal mill feed size distribution is determined by adapting a population balance comminution model to a measure of rock hardness or fragility which is also relevant to the rock fragmentation that is achieved by blasting. The relation between the size distribution and fragility of the feed and of the mill's product and the critical size in a SAG mill is examined.

Jan 1, 1993

By Robert A. Bauer

Introduction A longwall mining demonstration currently in progress in the Herrin (No.6) Coal Member near Benton, Illinois, involves the extraction of three adjacent panels by the longwall method. The first panel was completed in May, 1977. The Illinois State Geological Survey is involved in this project for two reasons: (1) to detail the geology of the roof and relate the geologic features to the behavior of the roof during mining operations, and (2) to study the nature and occurrence of coal balls (carbonate petrifactions of peat) encountered during this demonstration. General Geology of Area The stratigraphic sequence of beds immediately above the No. 6 Coal in this area, ranging from oldest to youngest, is: gray shale (Energy Shale Member), black carbonaceous shale (Anna Shale Member), and argillaceous limestone (Brereton Limestone Member) (figure 1). In some areas of the mine, where one of these units may rest directly on the coal, one or more of the members is absent from the stratigraphic sequence. The nature of roof for the area is shown in figure 2. It is greatly exaggerated in the vertical direction. The Walshville Channel, 11.3 km west of this mine, was a river at least in part deposited at the same time as the coal. The gray shale wedge on top of the coal, which thins away from the channel, is thought to represent an overbank deposit of mud from the channel. The next layer deposited on top of the gray shale, and on the coal not covered by gray shale, is the black carbonaceous shale, believed to represent a mud deposited in a brackish environment. The area where the roof lithologies change rapidly from one shale to

Jan 1, 1977