Search Documents

By R. K. Mehta

This paper presents the application of a simple genetic algorithm (SGA) to a coal slurry grinding process in order to find the optimum set of conditions under which the desired slurry properties can be attained. The operating parameters of the process were; slurry % solids, dispersant dosage, ball size, and mill speed. The optimization algorithm, which is based upon the mechanics of natural genetics, was used to find near-global optimum points specific to responses measured In terms of fineness, specific energy consumption, viscosity coefficient, and viscosity exponent. In order to minimize the viscosity of the slurry and simultaneously achieve a condition of maximum packing density, optimization was carried out by the penalty method using an overall objective function incorporating several responses. Computer results and analysis demonstrate the ability of the genetic algorithm to perform better than a traditional technique such as response surface methodology (RSM) and to rapidly locate "the global optimum".

Jan 1, 1992

By J. Kou

In this paper the activation behavior of quartz using Ca(OH)2 as an activator in quartz reverse flotation with anionic collector was evaluated and their adsorption behavior was investigated using a variety of techniques. The adsorption of the collector KS-I on the surface of quartz with and without Ca2+ was primarily characterized using Quartz Crystal Microbalance with Dissipation technique (QCM-D), which is a high sensitivity in-situ surface characterization technique. The flotation performance was evaluated using a laboratory mechanical flotation cell at different process parameters such as pH, collector dosage, and Ca(OH)2 dosage. The anionic collector evaluated was a commercial fatty acid KS-I. The QCM-D data showed that the collector adsorbed on quartz more readily with Ca2+ as activator. The mass and structural property of the collector layer adsorbed on quartz surface at 2.16×10-3 mol/L of Ca2+, 0.3 g/L of collector and pH 12.0 have been studied using the technique of QCM-D. The chemisorption of the collector KS-I on the surface of quartz in presence of Ca2+ were also demonstrated by means of zeta potential, QCM-D and FTIR analysis.

Feb 23, 2014

By Jian Deng, Hehua Zhu, Lianyang Zhang

Rockburst is defined as a sudden and violent explosion of rock on the surface of a rock excavation. Rockburst has been regarded as the least understood and most feared hazard problem for underground rock excavations. Traditionally, rockbursts were classified into the strain, pillar, and fault-slip categories. However, rockbursts are also known to occur at stress levels well below the rock yield strength, in mines where the rock is far from brittle, or without the presence of geological discontinuities. A plausible explanation of rockbursts is buckling, which has been identified as one of the main mechanisms for rockbursts. It is observed that rockbursts are often induced by dynamic loadings (pulses) from adjacent blasting. Therefore, the present paper studies the effect of pulse shape and amplitude on pillar rockbursts induced by dynamic loadings from blasting using the method of numerical analysis. The governing equation of a pillar’s motion is set up and the mechanism of pillar rockbursts is investigated through a practical example. The results show that it is not the shape of a pulse but the impact energy to decide the occurrence of pillar rockbursts. If all other parameters remain the same, pillar rockbursts are more likely to occur when the pulse duration is longer. The parametric resonance and the perturbation of dynamic loadings are also found to play an important role in the occurrence of rockbursts. These insights would provide invaluable clues about the mechanism and for better control of pillar rockbursts.

Apr 26, 2022

By Goran Mathisson

PLASMARED is a process in which one well established and one new advanced technology have been merged into a practical tool for production of high quality direct reduced iron at lowest energy consumption and costs. Before describing the process, we have to reiterate the simple fundamentals of making metallized iron from iron ores: The main components necessary are: - Iron oxide - Carbon and/or hydrogen - Heat

Jan 1, 1982

By Malcolm D. Flavel

Recent research into the mechanisms of crushing processes has led to the establishment of new criteria for the effective design and operation of comminution plants. This paper reviews this work and gives examples of the productivity gains and cost benefits that have been achieved in the practical application of these findings.

Jan 1, 1988

By E. E. Malouf

For centuries small amounts of copper have been recovered from acid mine-drainage waters. In recent years, the expansion of copper-bearing waste dump leaching for copper recovery has established a technological basis that is rapidly converting the art of copper leaching' into a science. Leaching of copper, whether from copper-bearing ore or waste, follows well established chemical reactions. These reactions are commonly in an acid circuit, but where leaching of copper is to be made in rock that is a high acid consumer, ammonia and ammonia carbonate, as well as cyanide leach solutions, can be used effectively. Current hydrometallurgical processes are being applied at an ever increasing rate to recover the trace amounts of copper in copper mine waste by in-place leaching. Currently approximately 300, 000 tons of copper are produced annually in this manner where as recently as ten years ago, only one-eighth of this amount of precipitate copper was produced.. Where copper occurs as an oxide in higher concentrations as to be classified as an ore rather than waste, then the hydro-metallurgical processes are applied as percolation or agitation leaching in vats, pachuca tanks, or prepared heaps. This approach gives better control over the recovery of the leach solutions, particularly in the processes where ammonia or cyanide leaching agents are to be used.

Jan 1, 1972

By G. Wang

With the depletion of easy-to-treat phosphate resources, low quality phosphate ores with high carbonates, particularly dolomite impurities have to be mined to meet the agricultural demand because of the continued growth of world population. The separation of dolomite from phosphate has been recognized as one of the most difficult subjects in mineral processing due to the similarities in their physical and chemical properties. Flotation is considered the most important approach for beneficiating both easy-to-treat and high impurity phosphate resources. There is no doubt that the development of reagents is the key for achieving satisfactory separation performance through flotation process. In order to separate dolomite from phosphate, Arr-Maz Custom Chemicals has made great efforts in developing flotation reagents for removal of carbonates from phosphate ores of different origins worldwide. This paper describes some flotation reagents and processes for the separation of dolomite or/and calcite impurities from phosphate in the ores from different locations.

Jan 1, 2010

By K. T. Brashear

Since the MINER Act of 2006, the minimum static load of in-situ underground mine seals has been increased from 20-psi to either 50-psi if monitoring is conducted or 120-psi if left unmonitored. These minimum strength requirements in seals must be designed, built, and maintained throughout the lifetime of the seal. Due to this, it has become necessary to assess the effectiveness of non-destructive testing (NDT) technologies to determine seal integrity, which in this case, are explored using sonic waves and tracer gases. Through both small and large scale testing, two NDT methods will be evaluated for their abilities to determine integrity of the seal. A sonic wave technique to observe a change in wave velocity to identify faults within the seal material. As a NDT method, tracer gases may be used as a potential indicator of a connection between both sides of the seal material through a series of faults and cracks within the material itself. This paper reviews the history of underground mine seals and discusses the overall assessment of sonic waves and tracer gases to serve as NDT methods for estimating the integrity of these seals.

Feb 23, 2014

By Y. J. Wang

Stall or aerodynamic stall of axial-flow fans has long been recognized as an important operational problem in mine ventilation. To develop a technique for characterizing fan stall in multiple-fan ventilation networks, a research project was initiated through the Generic Mineral Technology Center for Mine Systems Design and Ground Control. Considering that fan stall is related to multiple operating points, this paper discusses a numerical model for multiple-fan ventilation networks, design of the experimental setup for two-and three-fan ventilation networks, and numerical methods for solving multiple networks solutions. It is hoped that the results of this project will lead to an innovative method of ventilation network analysis and simulation, thus preventing stall.

Jan 1, 1991

By M. A. Cristovici

The possibility of using surfactants as wetting agents for the suppression of sulphide ore dust has been investigated. Numerous surfactants were examined to determine their characteristics and to investigate their ability to improve the wetting of the sulphide ore dust. However, the surfactants selected as suitable dust suppressors proved to have a negative effect on the flotation of the ore contaminated with such reagents. A method was developed to eliminate the detrimental influence of dust-suppressing surfactants. It consisted of surfactants adsorption on activated carbon and separation of loaded carbon prior to flotation. The technique is simple and requires minimal changes in the plant flowsheet.

Jan 1, 1990

By B. K. Parekh

Large reserves of coal pond fines are found in the Illinois Basin-over 40 million tons in Western Kentucky, over 65 million tons in Southern Illinois, and over 35 million tons in Southern Indiana. If these fines are used to produce coal-water slurry (CWS), fuel costs, NOx. emissions, and pond closure costs can be reduced. Coal fines from this region that are used to produce CWS for co-fire or re-burn may require processing, however, to attain proper particle size distribution and fuel quality. To evaluate the effectiveness of using coal cleaning technologies to control these CWS quality parameters, a simple flowsheet for recovering and processing coal pond fines was designed and tested. Coal fines processing consisted of using classifying cyclones to size at nominal minus 200 mesh, cleaning the classifying cyclone underflow using spirals, and cleaning the overflow using column froth flotation. Ash content of the dean coal from the spiral was reduced to about 10 percent, which is satisfactory to use for CWS co-firing in a cyclone-fired boiler. The clean coal from column flotation may be used for re-burn in a cyclone-fired boiler or as co-fire fuel in a wall-fired or tangentially-fired boiler. Heating value recovery during laboratory-scale, pilot-scale, and commercial-scale coal cleaning testing was about 80 percent.

Jan 1, 1998

By A. J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of steel wire ropes. Steel wire ropes are very suitable for mine hoisting due to their high strength and durability, but have the negative characteristic of a low strength/weight ratio. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength/weight ratio of synthetic ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application.

Feb 23, 2014

By U. Srivastava

In the processing of manganiferous ore, it is useful to control whether the manganese (Mn) goes to the iron product to produce ferromanganese, or to the slag for extraction as a high Mn product. This can be done by manipulating the thermodynamic conditions for manganese oxide(MnO) reduction to control whether it remains as MnO or converts to metallic Mn. Results are presented showing that during production of iron nuggets, reduction of manganese oxide (MnO) can be controlled by changing the furnace temperature and reductant composition appropriately.

Jan 1, 2010

By G. V. Sullivan

The Federal Bureau of Mines examined tailings samples from 13 western copper operations to determine the potential for recovering rutile. Results showed that six of the samples contained sufficient liberated titania to be considered potential sources. One sample contained 0.75 percent Ti02 or 0.40 percent liberated rutile. Batch flotation studies developed a procedure that recovered 70 percent of the liberated rutile at a grade of 34.7 percent TiO2. Sulfuric acid leaching studies on 12 of the samples dissolved 100 to 2,200 grams Cu per ton of tailings; leaching of the slimes showed slightly more copper was dissolved, 1,800 to 3,300 grams Cu per ton of minus lo-micrometer material. Bulk sulfide flotation of nine of the samples resulted in concentrates that contained 0.38 to 2.0 percent Cu and 0.7 to 2.1 and 6.9 to 42.9 grams per ton Au and Ag, respectively.

Jan 1, 1981

By I. Anazia

Selective fatty acid flotation of carbonate gangue from sedimentary apatites was achieved under acidic pH's without a specific apatite depressant and without conditioning the pulp with the collector. Concentrates (35-38% P205, 0.8-1% MgO) with high recoveries (80-85%) were produced from Indian and Chinese dolomitic ores. The calcareous and/or dolomitic-siliceous phosphate ores of South Florida and Utah required two flotation stages: one for carbonate removal, as mentioned above, and the other for phosphate recovery from siliceous gangue. Preliminary tests on the South Florida ore gave concentrates analyzing 29% P205 and 0.8% MgO with a P205 recovery of 76%. Data are also included showing the applicability of the process to the dolomitic-calcareous-siliceous Western U.S. phosphate ore from Utah. A concentrate obtained from this ore assayed 30% P205 and about 1% MaO.

Jan 1, 1987

By Kef ton H. Teague

This paper will discuss bentonite deposits in Texas, Oklahoma, Louisiana, Mississippi and Alabama. The discussion will be re¬stricted to a review of the so-called calcium or non-swelling bentonites. In other words the exchangeable cation is calcium. The term "bentonite" is used to describe a clay material, composed essentially of the clay mineral montmorillonite. In addition, bentonites may contain various impurities such as glass shards, feldspar, quartz, muscovite and biotite mica, glauconite, pyrite, hydrated iron oxide, gypsum, organic material, etc, Most of the southern calcium bentonites contain at least 70% montmorillonite, Bentonite as mined may range in color from dark grayish greens through various shades of grays, reds, yellows and browns to nearly white. It is normally massive and breaks with a conchoidal fracture. When air dried, closely spaced shrinkage fractures occur. Moist bentonite has a soapy feel, with little or no obvious "grit". Bentonite deposits were first discovered in Mississippi about 1925, in southern Monroe County. During the thirties and early 1940's, deposits were identified in Alabama, Texas, Oklahoma, and Louisiana. Perhaps the earliest production of southern bentonite was from a deposit in the valley of the Tombigdee River, south of Jackson, Alabama in 1936. Production commenced in Mississippi during the latter part of 1938 at Pontotoc. The growth and development of the bentonite industry in the southern United States owes its beginning to three events. The first of these was the discovery by German researchers,

Jan 1, 1972

By Russell L. Dahl

In a continuing effort to improve plant efficiency, United States Steel's Atlantic City Ore Operations completed the rubber lining of its balling drums in late 1982. This resulted in benefits of reduced bentonite consumption, reduced maintenance costs, improved production rates, and lower power consumption. These advantages far outweigh the disadvantages of increased oversize production and increased surging on the roll screen sizing devices. Certain operating characteristics and variables are discussed herein.

Jan 1, 1983

By Juan C. Diaz, Juan P. Carmona, Manuel Z. Salgado, Oscar J. Restrepo

The “Teaching Kids” project is an educational initiative for young people and children from elementary schools. It is carried out by Mining, Geological, and Environmental Engineering students from the SME Student Chapter of the Universidad Nacional de Colombia, Medellin. The primary purpose of the Teaching Kids project is to share knowledge about geosciences and mineral resources in a didactic and attractive way, emphasizing the importance of identifying the use of minerals in daily life and responsible and sustainable mining in our society. Furthermore, this project aims to promote the importance of pursuing geoscience majors in the new generations and improve the mining industry’s public perception. Different methodologies related to early childhood education are implemented, such as gamification, in which the dynamics of games are adapted during the development of workshops to teach and learn in an active and motivated environment. Furthermore, the Montessori Method is used. It implements textbooks, sensory mineral boxes, and presentations to allow learning through experimentation itself (Montessori 2003). The implementation of this methodology has been successful; it has shown high engagement, participation, and retention of the basic concept of geoscience and mining.

Feb 1, 2025

By Fouad Faraj

For every blast pattern, zones of unique material types need to be classified before mining. Most material types can be summarized into different kinds of ore and waste. Blocks generated from blasthole assays are too small to be selectively mined, so areas with a single material classification meeting the mine’s selective mining unit must be defined. Current industry standard practices are to manually draw ore/waste dig limits, but this process is subjective and results in quantities of dilution and ore loss that can be improved upon to enhance the profitability of mining operations. In this study, two weeks of production data from a homogeneous copper (Cu) porphyry and heterogeneous manto-type Cu deposit were used to assess the variability in the hand-drawn dig limits of 20 geologists, mining engineers and ore control specialists, which were compared with the optimal ore/waste delineation. The profit for 20 distinct hand-drawn dig limits for the homogeneous mine varied by 3.7 percent, from $10.5 million to $10.9 million, averaging at $10.8 million. The percentage was nearly double for the more heterogeneous mine at 5.9 percent, from $17.9 million to $19.0 million, averaging at $18.6 million. Using the optimal ore waste delineation, the profit increased to $11.0 million (1.9 percent increase) and $19.3 million (7.0 percent increase) for the homogeneous and heterogeneous deposit, respectively. The natural variability, diggability requirement and selectivity are identified as the main drivers of ore loss and dilution. Recommendations are provided for reducing the subjectivity in manual hand-drawn dig limits by integrating dig limit optimization algorithms as a tool to assist practitioners.

Oct 1, 2024

By P. Somasundaran

Three major types of solution chemical equilibria involving flotagents (Le. flotation reagents such as collectors, frothers and modifiers), minerals and solution play a crucial role in determining the behavior of complex flotation systems. Minerals of phosphates (apatite and francolite), tungsten (wolframite and scheelite) and associated carbonates (calcite and dolomite) are sparingly soluble in aqueous solution and form dissolved mineral species in bulk solution. Such dissolved species interact with mineral solids, often resulting in surface conversion of the minerals. In addition, they can interact with various flotagents and lead to surface or bulk precipitation and loss of selectivity in the flotation. Relevant solution equilibria of such sparingly soluble minerals and their interactions with oleic acid and structurally modified reagents were determined in this study using a multi-pronged experimental approach. Methods to manipulate and control the solution chemical equilibria and thus achieve selectivity in flotation systems are discussed.

Jan 1, 1990