Search Documents

By R. R. Klimpel

The efficiencies of plant scale comminution processes are often evaluated by various indices that are calculated and/or measured somewhat independent of the performance of any associated downstream froth flotation processes. In order to compare some specific comminution factors such as energy utilization, media consumption, equipment utilization time, etc. comparisons of comminution efficiency independent of flotation behavior are appropriate. However, as more and more detailed plant level information is gathered on the joint and highly interactive nature of comminution and froth flotation, it is becoming increasingly obvious that knowing and using simple efficiency indices are not enough. What is needed are more performance related measures of the efficiencies of the combined size reduction -froth flotation system for effective plant level economic optimization to occur. The purpose of this paper is to present some examples of important interactions that influence the joint efficiencies of size reduction and froth flotation processes.

Jan 1, 1998

By Bruce H. Mason

Lightweight aggregates are classified as those minerals, natural rock materials, rock-like products, and byproducts of manufacturing processes that are used as bulk fillers in lightweight structural concrete, concrete building blocks, precast structural units, road surfacing materials, plaster aggregates, and insulating fill. Other uses include architectural wall covers, suspended ceilings, soil conditioners, and other agricultural uses (Mason, 1989). One unusual agricultural use recently reported was for bedding on a crocodile farm on the south coast of Natal. It seems that female crocodiles became upset because there was no vermiculite in which to lay their eggs due to the late arrival of a consignment of vermiculite. The vermiculite was being used as a substitute for river sand to nest crocodile eggs (Griffiths, 1989). The various lightweight aggregate materials may be classified into four groups as follows: 1. Natural Lightweight Aggregate Materials-prepared by crushing and sizing natural rock materials, such as pumice, scoria, tuff, breccia, and volcanic cinders. 2. Manufactured Structural Lightweight Aggregates-prepared by pyroprocessing shale, clay, or slate in rotary kilns or on traveling grate sintering machines. 3. Byproduct Lightweight Aggregates-prepared by crushing and sizing foamed and granulated slag, cinders, and coke breeze. This group of lightweight materials, with the exception of slag, has become less significant and will not be discussed in this chapter. Other lightweight aggregates are beginning to appear in the marketplace. Some are the result of manufacturing processes on industrial byproducts and/or waste products, such as fly ash and incinerator residue (Bigner, 1992). 4. Manufactured Insulating Ultralightweight Aggregates-pre- pared by pyroprocessing ground vermiculite, perlite, and diatomite. The application of diatomite in brick and in extruded and aggregate forms has declined in recent years (Kadey, 1983) and will not be considered in this chapter. Lightweight aggregates for structural concrete and concrete masonry units, according to the American Society for Testing and Materials (1986) consist of "aggregates of low density used to produce lightweight concrete, including: pumice, scoria, volcanic cinders, tuff and diatomite; expanded shale, clay, slate, perlite, vermiculite or slag; and end products of coal or coal combustion" (Mason, 1989). Lightweight aggregates are distinguished from other mineral aggregate materials by their lighter unit weights-1 281 to 1 602 kg/m3 or less for loosely packed lightweight aggregates-as com- pared to 2 002 kg/m3 or more for crushed stone, sand, gravel, air-cooled slag, and other common mineral aggregates. The specific gravities of these lightweight aggregates are also used to classify them for use in concrete; they range from the extremely light materials, used for insulative and non-structural concrete to expanded shale, clay, slate, and slags used for structural concrete. Vermiculite and perlite are sometimes referred to as super light- weights. Insulating concrete (non-load bearing) weighing as little as 240 kg/m3 can be made with these aggregates. Natural aggregates such as pumice, pumicite, and scoria are normally made into concrete weighing about 400 to 480 kg/m3. Expanded shale, clay, and slate produced in a rotary kiln make structural concrete ranging from 1 201 to 1 842 kg/m3. Expanded shale and clay produced by sintering make concrete that ranges from 1 442 to 1 922 kg/m3. Air-cooled slag produces concrete ranging from 2 162 to 2 403 kg/m3. The low density lightweight aggregates are used primarily for insulating purposes. They have relatively low compressive strength. The middle density aggregates are used for insulation and for fill. Those at the upper end develop excellent compressive strength and are used in many structural applications (Anon., 1971). In recent years, the production of lightweight aggregates in the United States for all uses (including insulation and construction materials) has averaged about 19 Mtpy (Table 1). The production and consumption of lightweight aggregate is closely tied to the fortunes of the construction industry and the need to construct energy efficient buildings. Recent years have seen the production of lightweight aggregate approach the levels of the early 1970s. The period of 1979 to 1981 was a low point in production levels. The low levels of production were caused by significantly higher plant energy costs due to the large amounts of fuel and energy used in the production of most types of lightweight aggregate. Lower levels of construction activity also affect production levels. This chapter focuses on the use of natural lightweight aggregates and manufactured insulating ultralightweight aggregates, and on both the production and use of manufactured structural light- weight aggregates. Some additional comments are made on byproduct materials. Separate commodity chapters on vermiculite, perlite, pumice, and volcanic cinders are elsewhere in the volume. Discussion of the commodities covered elsewhere in the book will be limited to observations on their utilization and relation to other lightweight aggregate materials.

Jan 1, 1994

By Thomas A. Morley

This paper deals with the minimization of ventilation costs for the controlled-flow mine ventilation network. Cost elements considered include the cost of power and the fixed cost of the fans. The problem is modeled in a mixed-integer programming format and solved via the branch and bound method. Computational experience with sample problems is discussed.

Jan 1, 1983

By Kenneth A. Grace

Introduction The 1980s have not been kind to the mining industry, especially in the United States. As mineral commodities prices plunged, marginal producers were squeezed out and then major players were forced to cut back or close down operations. Base metal miners suffered the most. Gold was all that glittered. As had been the case throughout min¬ing's history, exploration activity was an early victim of these depressed conditions. Mining companies had to economize drasti¬cally and exploration was deemed a nones¬sential activity. Funding for new explora¬tion ventures dried up as mining was seen as a poor investment. A national magazine even proclaimed the death of the industry. Indeed, ignoring matters of independ¬ence of supply and the relationship of min¬eral production to national security, it was argued that mining was but a small cog in the overall scheme of things in the United States. The industry made a relatively small contri¬bution to the gross national output. We were becoming a service industry economy, re¬member? But what of those countries where mining plays a major role in the economic well-being? In some, mining is the national economy. In a few specific cases, special conditions actually brought prosperity. Copper production in Chile is one example. There, high grade copper, low production costs, and a technically advanced industry reaped the benefits of mine closures else¬where. In most other cases, however, par¬ticularly in the lesser developed countries, whole economies were devastated. This article will show what one major mineral producer, Canada, did to ensure the survival and even growth of its minerals exploration activity during these lean years. Background While Canada is among the world's mining leaders, mining is not its dominant industry. Still, it plays a far more important role than in the United States. It is a major earner of foreign exchange, currently accounting for about 25% of the total value of exports. Through spinoffs and a multiplying effect, it is a significant employer. In the far north, particularly, mining is the major nongovernment industry and a leading factor in the opening up of frontier territory. The industry cannot be allowed to die because it is often the main economic underpinning for vast, remote areas. Thus, exploration for new deposits cannot be cur¬tailed significantly without it having a long¬term negative impact on the very fabric that melds such a large, sparsely-populated ex¬panse of country into a nation. Over the years, Canadian governments have employed various means to encourage the development of new mines. Often, these incentives were tax-oriented, such as the three-year income tax holiday that applied to new mines in the 1950s and 1960s. The advantage of the tax connection is that any such incentive policy can be applied across the board to the 10 provinces and two territories that make up the federation of Canada. This is important because mining, except for the two federally-administered northern territories, comes under provincial government jurisdiction. Mining taxation is a complex give-and-take between the central and provincial authorities. In Canada, expenditure on mineral exploration is an allowable cost against reve¬nue for tax purposes. This works well pro¬vided there is some revenue from which to deduct. New exploration companies, those with no income from mining activities, de¬rive little benefit from this type of tax provi¬sion. Similarly, in times of depressed prices and reduced or nonexistent profits, the tax deductibility of exploration spending loses its value even for the major mining compa¬nies. To encourage exploration in Canada during the lean years, a different sort of incentive was required. The instrument used during the 1980s was again tax connected. It became known as flow-through financing or, simply, flow-through shares. When it assumed its final shape, it worked dramati¬cally. Flow-through shares Flow-through shares are so-named because they permit tax benefits earned by a corporation to 'flow-through' to the share¬holder. Basically, when an investor buys a flow-through share and the proceeds de¬rived by the company from this transaction are used for Canadian exploration, the in¬vestor can claim a deduction for tax pur¬poses as if the exploration expenditure was made by him personally. Flow-through shares go back to the early 1970s when Canada revamped its mineral income tax law. At that time, it permitted full deduction of exploration and development expenditures and provided for an automatic depletion allowance of one¬ third of operating profits from mining. There was also the three-year income tax holiday for new mines. New legislation replaced the depletion allowance with an earned depletion arrange¬ment whereby one dollar of depletion was earned for every three dollars spent on ex¬ploration and development. This earned depletion was `banked' during a transitional period (to 1974). After that it could be deducted from resource profits up to a maximum of 25% of such profits in any one year, with the excess carried forward. To promote exploration and mine de¬velopment in Canada, the earned depletion allowance plus the continued deductibility of exploration and development expendi¬tures permitted the recovery of risk capital before taxation. The three-year tax holiday, however, disappeared. Also, mining com¬panies that did not reinvest in exploration lost the depletion allowance benefit.

Jan 1, 1989

By D. Bhattacharyya

The adsorption and desorption of gold cyanide by activated carbon is significantly influenced by particle size of the activated carbon particles and the chemical environment. A series of adsorption and elution experiments have been performed with ten different particle size fractions. The tests indicate that although the ultimate adsorption capacity is independent of the activated carbon particle size, the adsorption rate is strongly affected by the particle size. Further, desorption characteristics using traditional Mintek and atmospheric Zadra procedures reveal interesting trends with variation in particle size and will be discussed in this paper.

Feb 23, 2014

By R. C. Bunge

A magnetogravimetric separation is the consequence of two competing forces with opposing directions, i.e., magnetic buoyancy and gravitation (or centrifugal force). While magnetic buoyancy is a function of particle volume, gravitational force depends on particle mass, thus permitting a separation according to specific gravity. Since magnetic buoyancy is not a phenomenon of common knowledge, this chapter is meant to briefly introduce the theory of magnetogravimetric separations. A particle that is suspended in a magnetic fluid which is exposed to an inhomogeneous magnetic field experiences a repulsive force -the so called magnetic buoyancy. In order to illustrate this effect, an analogy with the more familiar hydrostatic buoyancy is drawn. Hydrostatic buoyancy occurs due to unsymmetrical pressure distribution 'above' and 'below' a suspended particle (fig. 1).

Jan 1, 1990

By G. B. Amicucci

A Denver Autometrics Particle Size Monitor, PSM-400, was installed at Golden Sunlight Mines, Inc. in October 1988. The PSM-400 measures the grind product's particle size and percent solids. The particle size is used to control grind size by automatically adjusting mill feed rate. The PSM's continuous response to ore changes has improved grind product uniformity and mill throughput. Metallurgical testing has shown the PSM's accuracy to be +/-1 % + 150 µm (100 mesh).

Jan 1, 1991

By Lok W. Home

INTRODUCTION Today, raise drilling (boring) has become the stan¬dard method of raising throughout the Western world. It is estimated that the majority of raise footage com¬pleted in 1977 was accomplished by the raise drilling method. Extensive replacement of the drill and shoot system by mechanized raise drilling has occurred be¬cause users have recognized one or more of the follow¬ing advantages. In a direct cost per meter comparison, mechanized raise drilling is economically more attractive than drilling and shooting. Mechanized raise drilling offers improved personnel safety over the drilling and shooting method. Mechanized raise drilling is a faster and more predictable method for excavation than is drilling and shooting. The raise cost per unit of length becomes less as the raise length increases, offering greater flexibility in the overall design of mines. Mechanized raise drilling provides a substantial reduction in labor requirements. 6) Mechanized raise drilling improves the working environment. 7) Mechanized raise drilling improves the rock in¬tegrity of round, unblasted raises. Increasing acceptance of the raise drilling technique is enhanced by continuing equipment development. Today, a wide range of machines and capabilities is available, machine drive systems have been improved, reliability has been increased, and cutter technology is being improved quite rapidly. Table 1 lists the four major manufacturers of raise drilling machines, cutters, and reamers, together with the approximate number of machines that each company had in operation at the end of 1977. Although Reed and Smith are major suppliers of reamers and cutters, they do not manufacture the drilling machines. Four or five other relatively minor suppliers have built machines, reamers, and cutters for raise drilling, but they did not have a substantial num¬ber of machines in the field at the end of 1977. MACHINES FOR MECHANIZED RAISE DRILLING There are three principal arrangements for making machine-bored raises. They include the use of standard raise drills, reversible raise drills, and blind-hole or box¬hole raise drills. Standard Raise Drills The standard raise drilling machine is set up on one mine level or on the surface, and a pilot hole is drilled from that level or surface to a level below. When the pilot hole has been drilled, the raise then is reamed back from the lower level to the upper level or the surface. This arrangement is illustrated in Fig. 1. Reversible Raise Drills The reversible raise drilling machine is set up on a lower level of the mine, and a pilot hole is drilled up¬ward to a higher level. The raise then is reamed back from the upper level to the lower level. This arrange¬ment is illustrated in Fig. 2. The machines used for this type of raise drilling normally are capable of being used as standard raise drills. Blind-Hole or Boxhole Raise Drills The blind-hole or boxhole raise drilling machine is set up on a lower level of the mine, and a full diameter raise is bored to a higher level without the use of a pilot hole. This type of machine is illustrated in Fig. 3. Drill Recommendations If access to upper and lower mine levels is equal, the standard raise drill should be used. The complexity of the equipment and associated handling procedures for boxhole drilling far outweigh any mechanical advantage or reduction in the number of operations, provided that access to an upper level is available. If there is good access to a lower level but only limited access to an upper level, the use of a reversible raise drill should be considered. If there is no access to an upper level, a blind-hole or boxhole raise drill is the only practical mechanized system. MACHINE SELECTION There are six major considerations in selecting a machine for raise drilling. These include operating range, cutter loading, machine structure and main¬tenance, drill string configuration, drive system, and automated controls. Operating Range As shown in Table 2 and Figs. 4 through 6, raise drilling machines are available for a wide range of hole sizes. Standard raise drill ratings range from raises of 0.9 m (3 ft) diam and 120 m (400 ft) length up to raises of 3.5 m (12 ft) diam and 900 m (3000 ft) length. Boxhole raise drilling machines are available for raises ranging from 0.9 m (3 ft) to 2 m (6 ft) diam with lengths up to 90 m (300 ft). Table 2 lists, among other criteria, the torque and thrust of typical machines; torque and thrust are the main criteria for analyzing the capacity of a machine. The raise sizes shown in Table 2 assume a condition of medium hard to hard rock formations and optimum cutter loading. The recommended raise size for a given machine can be exceeded when raising softer rock formations or when the operator is willing to accept a lower level of performance; the performance is related directly to the 1093

Jan 1, 1982

By W. R. Reed, J. P. Rider

"The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently developed a series of models utilizing computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a medium-sized surface blasthole drill shroud with a dry dust collector system. CFD models were constructed in ANSYS FLUENT Version 15. Previously run experiments conducted in the NIOSH full-scale drill shroud laboratory were utilized to validate the models. The setup values in CFD models were calculated using experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for test scenarios, including 0.14 m3/s (300 cfm) bailing airflow with 2:1, 3:1, and 4:1 dust collector-to-bailing airflow ratios and 0.24 m3/s (500 cfm) bailing airflow cases with 2:1, 3:1 and 4:1 dust collector-to-bailing airflow ratios. For the 2:1 and 3:1 ratios, results showed the calculated dust concentrations from the CFD models were within the 95% confidence intervals of the lab experimental dust concentrations. This paper describes the methodology used to develop the CFD models, to calculate the model dust input, and to validate the models based on experimental data. Problem regions were identified and revealed by the simulation of a dry dust collector system. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. INTRODUCTION In surface mines, production drilling is an essential process in blasting which fractures the hard rock overburden for removal. Holes with a predetermined pattern, diameter, and depth are drilled into the overburden to introduce explosives. During the drilling process, considerable amounts of respirable dust are produced. Past research conducting area sampling at blasthole drills has documented time-weighted average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 [1] and 1.04 to 52.30 mg/m3 [2]. These high dust concentrations, which may contain silica, can lead to respirable dust over-exposures for the drill operator, drill helper, and other personnel in the vicinity. These over-exposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal. In order to prevent the development of silicosis to mine workers, the Mine Safety and Health Administration (MSHA) regulates the exposure to respirable dust. For metal/nonmetal (M/NM) mines, MSHA has adopted the threshold limit values recommended in 1973 by the American Conference of Governmental Industrial Hygienists (ACGIH) [3]. The total airborne dust standard is 10 mg/m3. However, if the sample contains greater than 1 percent quartz (the most common form of crystalline silica), a respirable dust standard is calculated with the following equation: Respirable dust standard = (10 mg/m3) / (% respirable quartz + 2)"

Jan 1, 2016

By Solomon J. Salat

During the major expansion of the Inspiration smelter, which took place in 1973, the bulk material handling system underwent a matching expansion in order to move the required materials. Inspiration is the first smelter worldwide to employ electric smelting in conjunction with the use of Hoboken converters (1), (2). The installation includes a 51 -MVA electric furnace, five 4.25m (14-foot) diameter Hoboken converters, rotary dryer, bedding plant, acid plant, heat recovery steam plant, and gas and dust handling system. See Figure 1, Plot Plan. As of today, the 51-MVA electric furnace is the world's largest in the smelting of copper. Engineering design for the installation was per- formed by Treadwell Corporation of New York. The task of designing the conveyor system was complex because the system had to be installed while the smelter was operating and with minimum plant shutdowns, and it had to serve both the existing and the new smelter. Existing conveyors were redesigned where necessary and incorporated into the new conveyor system. See Figure 2, Flow Sheet. The system encompasses the handling of such diverse materials as wet and dry copper concentrates, cement copper, silica flux, cold dope, and concentrate and flue dust.

Jan 1, 1979

By J. Snowberger III

Rhenium is a valuable and extremely rare chemical element with unique chemical properties. It is extracted commercially as a byproduct from the processing of molybdenite associated with porphyry copper ores. There is a present interest in recovering rhenium from copper pregnant leach solutions (PLS) produced by copper heap and stockpile leaching. These solutions contain rhenium at very dilute concentrations, typically in the 1 mg/L concentration range. This paper describes laboratory column ion exchange experiments to extract rhenium from these solutions using weakly basic anion exchange resins and actual plant PLS from two operating mines. The dynamic loading and elution behavior of Re on Purolite® A170 and A172 is discussed.

Feb 23, 2014

By A. Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5M tons. Trona is an evaporite mineral that is processed into several products, mostly soda ash. The underground mine has two active development panels and one longwall (LW) panel. The mining horizon is about 500m below surface and the surrounding strata liberates methane. Three surface-based, blowing fans provide ventilation air as a positive pressure system. The mine operates a 225m long LW face, built by Joy Mining Machinery. Headgate and Tailgate developments are driven with four entries. The recovery room, at the end of each panel, is 8m wide with three access chutes. Additional recovery room support comes for concrete blocks used with a center to center spacing of 1.5m. As the LW enters this pre-driven recovery room there are notable responses and shifting ground stresses. This study was undertaken to measure the ground response using seven vibrating wire displacement transducers. These devices were used to monitor the convergence as the LW approached the recovery room. The methane concentration in the air ventilating the recovery room was also monitored. The correlation between convergence and gas liberation was then studied. The results show that the convergence varies from 0.1m to 0.25m along the length of the recovery room. Ventilating the recovery room becomes critical as methane is liberated from oil shale as the more plastic floor material is disrupted. Appropriate methods are employed to ventilate the recovery room.

Feb 23, 2014

By W. Petruk

Mineral liberations that would be obtained by grinding an ore to a specific size can be predicted by analyzing unbroken ore pieces, and mineral liberations in ground ores and mill products can be determined directly by image analysis. Predictions of mineral liberations are made by measuring size distributions and textures of mineral grains by image analysis, and using liberation models. Ground ores and mill products are analyzed to determine the proportion of mineral that is liberated, and the data are used to evaluate mineral behaviour during mineral beneficiation. The liberation data for minerals in a suite of mill products from a circuit are processed by a materials balancing technique to calculate recoveries of minerals in different types of particles throughout the circuit. The liberation-materials balance data define mineral recoveries; define the behaviour of an ore in a concentrator, pilot plant or bench test; and indicate whether recovery improvements are possible and/or feasible.

Jan 1, 1991

By R. Q. Honaker

Recent research has shown that enhanced gravity separators provide the opportunity to effectively clean I mm x 37 micron coal. At Southern Illinois University, a detailed experimental program was performed on a continuous Falcon Concentrator, which was found to achieve separations at mass throughput capacity values in excess of 100 tonnes/hour. The apparent particle separation density for I mm x 73 micron coal was about 1.60 with relatively high efficiency (Ep = 0.12). Typical ash and sulfur rejection values of 85% and 70%, respectively, were achieved while recovering 85% of the combustible material. Metallurgical and efficiency data from the evaluation are presented in this publication.

Jan 1, 1998

By T. J. Smolik

The Golden Sunlight Mine started full-scale operations in February 1983, with a conventional open-pit mine supplying 4464 tonnes (5000 tons) per day of milling ore. After crushing and grinding, the ore is leached with cyanide solution in large agitation tanks. Soluble gold values are removed from the sand portion of the leached ore with five stages of countercurrent washing cyclones. After thickening of the cyclone-wash overflow slurry, the gold is recovered in activated carbon with a six-stage carbon-in-pulp circuit and a five-stage upflow carbon column circuit. Pressure stripping, carbon reactivation, electro-winning and refining complete the gold recovery process.

Jan 1, 1984

By Nathaniel Arbiter

A fully-instrumented driving mechanism has been constructed to study the power, aerating and solid suspension characteristics of several laboratory flotation machines. Machines operating over normal flotation speed ranges give constant power numbers in liquid' systems indicating that they operate under fully baffled turbulent flow conditions. Owing to lack of geometrical scaling, power numbers for different sizes of cells of the same make are different. Even larger differences occur between cells of different manufactures. For a given impeller, varying the tank size did not significantly affect the power consumption. Tank geometry and baffling has a slight effect on power consumption with shrouded impellers. For a given impeller speed, suspension height decreases while power increases with increasing mass of solids in suspension. While power consumption is hardly affected by particle size and clearance between the impeller and tank bottom, the suspension height significantly increases as clearance increases and as particle size decreases. Aeration was found to affect not only power but also the suspension characteristics of the machine. For closely sized particles drastic sedimentation occurred when a critical value of the air flow number was exceeded. The critical air flow number decreased with increasing particle size. This effect was less marked with a wide particle size range. The self-aerating capacity of flotation machines increases with cell size at a given speed for the same impeller-shroud system, but decreases in the presence of frother and solids. Equations have been established for correlating all of the studied variables. Data taken from the literature were also correlated with these equations.

Jan 1, 1968

By Ulrich Maidl, Marc Comulada, Janosch Stascheit

"INTRODUCTION Cohesive soils are notorious for causing clogging of the cutter head and the excavation chamber of tunnel boring machines (TBMs). While clogging leads to a drastic reduction in excavation performance, it further induces higher wear of tools and other parts of the cutter head and may even prevent a controlled support of the tunnel face and, thus, lead to face collapse and excess settlements or sinkholes. Employing well-balanced soil conditioning techniques, the clogging tendency can be significantly reduced. The monitoring and control of soil conditioning as well as the timely detection of potential clogging tendencies require a close monitoring of all relevant machine parameters and measurements. To this end, a reliable and powerful Process Controlling software that gathers all machine and process-related information is a prerequisite for successful mitigation of clogging-induced problems. The remainder of this contribution is organized as follows: First, a brief introduction to the Process Controlling system PROCON is given. Afterwards, the mechanisms and mitigation techniques of clogging are discussed. Finally, an example is given how Process Controlling has been employed to soil conditioning in a tunneling project with highly clogging soils.PROCESS CONTROLLING Being both the active part and a huge measuring device, the shield machine represents the core component in mechanized tunneling. This machine comprises a manifold of complex components and devices that require constant supervision and control and, thus, is equipped with a manifold of different sensors that provide a continuous monitoring of the state and condition of the machine (Maidl & Stascheit, 2014). If these data are put into the whole context of the tunneling process, they can provide insight to the assessment and optimization of the performance and to the prediction of potential risks and hazards such as, for example, the tendency of clogging of the cutter head."

Jan 1, 2016

By J. Seiter

Mining has always been among the most hazardous of occupations, and with the increasing demand for coal and minerals, safety in mines assumes even greater importance. Worldwide, underground miners are being exposed to noise and respirable dust hazards associated with roof bolt drilling. These hazards are now being understood to cause irreparable damage to the health of miners. The objective of this research was to discover if a Polycrystalline Diamond Cutter (PDC) drill bit generates less respirable dust and hazardous noise than a competing Tungsten Carbide (WC) bit, in dry vacuum drilling. In order to control the drill parameters the drilling tests have been conducted in a laboratory setting. The results were met by determining the quantities of dust and noise generated using each drill bit and analyzing those levels by using monitoring devices and software to collect the data. This paper includes information on experiment setup, equipment used, drilling parameters, and data collected. The test results suggest that there are noticeable trends that the PDC bits produce less dust than WC bits but more testing is needed to substantiate these trends.

Feb 23, 2014

By J. A. King, D. R. Weir, P. C. Robinson

The complex mineralogy of the Porgera resource has a pronounced effect on process selection for the recovery of refractory gold and silver. Intimate association of gold with pyrite necessitates a high degree of sulphur preoxidation to achieve acceptable levels of gold recovery. Acid pressure oxidation has been demonstrated to be the only commercially proven process capable of achieving the required level of pyrite oxidation. Gangue mineralization dictates preconcentration of the sulphides to limit the acid consuming capacity and carbon dioxide generation during oxidation. However, the relationship between concentrate sulphur grade and gold recovery to concentrate ultimately governs the optimum degree of sulphide preconcentration. Minipiloting of the preconcentration and oxidation stages of the Porgera flowsheet are described. The influence of these processes on subsequent recovery of precious metals together with the technical and economic necessity of concentrate pretreatment prior to oxidation are discussed.

Jan 1, 1987

By Tony Walsh

Australian Stock Exchange Limited (ASX) -ASX is ranked 9th in the Morgan Stanley Capital International (MSCI) Index – only 2.02% of that Index. -1520 companies – 400+ mining & mining exploration. -Over 50% of Australians own shares in ASX listed co.s -Disclosure standards play a vital part in providing investors with confidence, thereby building depth and liquidity in the market.

Jan 1, 2003