Search Documents

By Marc Carriere

Bright-orange couplings adorning piping systems are a common sight in just about every underground mine in North America. Grooved mechanical piping, the pipe-joining system that utilizes these couplings, is the preferred method for joining underground and plant piping systems in the mining industry, due to the ease and speed of installation and maintenance. However, the applications for such systems have traditionally excluded high-pressure systems. Most grooved mechanical couplings have a moderate working-pressure limitation, so high-pressure systems have required the use of alternative joining methods, typically heavy-duty flanges. However, the introduction of high-pressure couplings (up to 4,000 psi) has made the grooved joining method viable, and even preferable, for backfill, deep-mine chilled water and dewatering lines and other high-pressure piping applications. As engineers explore the use of high-pressure couplings, questions will undoubtedly arise about the joining method?s capabilities. This article will address the capabilities and specifications of high-pressure couplings, and compare flanged and grooved mechanical pipe joining in traditional as well as high-pressure underground mining applications.

Jan 1, 2011

By Mustafa Fener, Masoud Rostami, Sair Kahraman, Behnaz Dibavar

The paper introduces a new rock mass cuttability classification (RMCC) system for roadheaders used in coal mines. It includes performance prediction models for both axial and transverse roadheaders, based on six parameters: uniaxial compressive strength, Cerchar abrasivity index, volumetric joint count, strike and dip of joints, joint aperture, and groundwater condition. The study validates the RMCC system through field and laboratory measurements, showing high correlation coefficients between net cutting rates and RMCC indices.

Nov 1, 2023

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Mine explosions are one of the most concerning risks related to underground coal mining, as a single gas explosion can cause injuries and fatalities among miners. Underground infrastructure seals and build-in-place (BIP) refuge alternatives (RAs) are employed to isolate an area from active workings to mitigate coal mining-related accident risks. They are designed to withstand blast pressures from a possible accidental detonation of the contained gas or a coal dust explosion. Crosscut seals and BIP RAs, typically consisting of steel-reinforced concrete, are prone to strong convergence and have a significant leakage potential due to high convergence damage near mined-out areas. The roof-to-floor convergence can change the structural integrity of these structures, and altered structural integrity can lead to less explosion resistance capability. Hence, a thorough analysis is needed to further understand their explosion response under various strata conditions.

Jul 1, 2023

By Ping Zhang, Xu Ma

Perturbations from mining operations significantly affect the stability of rock masses, especially with the increase in mining depths. This study uses the discrete element method (DEM) to investigate shear slip failure along discontinuities in an underground mine, aiming to quantify seismic moment and seismic energy to better understand seismic hazards.

May 1, 2023

By Diler Katircioglu-Bayel

This study aims to investigate the effect of combined mechanical and ultrasonic milling on the size reduction of talc. First, the talc sample was wet-ground in a stirred media mill for five different lengths of time (30, 60, 90, 120 and 150 min), and the optimum result was subsequently achieved with treatment by ultrasonication. The effects of amplitude (20, 35 and 50 µm), solid ratio (2.5, 5, 7.5 and 10 percent), and sonication time (60, 120 and 240 min) on the sizes of the final product were investigated. The pre-milling by wet grinding caused a decrease in the grinding resistance of talc. Sequential ultrasonic treatment, which was applied to the talc sample, generated smaller particles in comparison to those acquired by stirred media milling alone. Experimental results were assessed based on the product particle size (d10, d50 ), reduction ratio and specific energy consumption. Submicron particles prepared by ultrasonic treatment were highly stable compared to stirred media milling alone as investigated in terms of particle size. In addition, the effects of mechanical and ultrasonic milling on the structural properties of talc particles were characterized by X-ray diffraction (XRD) analysis.

By FELIPE SÁNCHEZ, PHILIPP HARTLIEB

Innovation plays a critical role in the mining industry not only as a tool to improve the efficiency of its processes and to reduce costs but also to meet the increasing social and environmental concerns among communities and authorities. Technological progress has also been crucial to allow the exploitation of new deposits in more complex scenarios, such as lower ore grades, extreme weather conditions, deeper deposits, harder rock mass and high-stress environments.  

By REHMAN ATTA UR, Kwame Awuah-Offei

This work evaluated the effects of bucket orientation and operating parameters on resistive forces and penetration for rubber-tire loaders (RTLs), such as load-haul-dumps (LHDs) and front-end loaders (FELs). The work used a 1:16 scale LHD model to test an RTL bucket operating at different levels of traction (tractive effort), speed, digging height and rake angles in a full factorial design experiment. The test was repeated on two muck piles with different particle sizes, and generalized regression modeling was applied to test the association of rake angle, tractive effort, speed and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The results show that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces — a novel finding that enhances our understanding of RTL loading. The results also show that the effects of speed, tractive effort and height above the floor all change with changes in particle sizes. This work provides insights into the effects of rake angle, height above the floor, tractive effort and speed on penetration and resistive forces for RTLs to facilitate better design and efficient use of these loaders.

By CORA ROELOFS

While the COVID-19 pandemic has dominated the headlines, another epidemic in the United States has continued apace — the opioid epidemic. Half a million opioid overdose deaths have occurred in the United States since 1999, when the opioid epidemic began. The causes of the epidemic include the rise in prescriptions for opioid pain medications, including for work-related pain. Miners and other occupations identified as physically demanding and at higher injury risk have been found to be at increased risk for opioid overdose [1]. However, awareness of the risk factors that might lead to opioid use, the potential hazards associated with their use, and resources to prevent addiction and death can allow miners to make choices that can reduce these risks.

By Jaisen Kohmuench, Michael J. Mankosa

Flotation has long served as the foundation for sulfide mineral recovery. As ore grades decline, however, this traditional approach is being pushed to the limit. Nowhere is this more evident than in the challenge of recovering coarse, partially liberated particles — an area where conventional flotation systems typically underperform due to excessive turbulence. As a result, valuable coarse minerals are often lost to tailings. Fine grinding has become the default solution, although with the added burden of higher operating costs and more challenging tailings disposal. To address the challenge of coarse particle recovery, Eriez developed the HydroFloat, a technology that uses a novel fluidized-bed approach to extend the upper particle size range of flotation significantly. The HydroFloat can recover particles exceeding 0.5 mm in diameter with a sulfide surface expression as little as 2 percent. Coarse particle recovery allows for optimization of comminution circuits for coarse gangue rejection before fine grinding. A substantial increase in overall tailings particle size provides higher water recovery due to improved drainage and allows for consideration of a dry, stacked tailings option instead of a tailings dam/impoundment. The technology’s transformative potential has not gone unnoticed. In recognition of its impact, Eriez was honored with the 2024 Robert E. Murray Innovation Award, commonly referred to as the Murray Award, by the Society for Mining, Metallurgy & Exploration. This prestigious award was established in 2017 to recognize organizations that advance the mining industry through the implementation of technical innovation. The HydroFloat stands as a fitting example of how creative thinking and industry collaboration can solve long-standing technical challenges.

Oct 1, 2025

By E. McCarthy

"INTRODUCTION Talc is a hydrous magnesium silicate with the approximate elemental composition 4MgO.3SiO2.H2O. It is one of the layered phyllosilicates (like kaolin and mica) but it differs from these in that it is relatively hydrophobic. This is due to its unique crystalline structure whereby a brucite inner layer is sandwiched between silica layers and the adjacent silica layers have no interlayer bonding other than van der Waals forces. This allows talc to be sheared easily along this basal plane, and the surface is covalent not ionic. Talc occurs both as a relatively pure material (>90% talc content) and in conjunction with many other minerals in proportions all the way from 1% to 90%. At lower concentrations, it is often considered a nuisance mineral when it occurs with base metals like copper, molybdenum or nickel or with precious metals like platinum or palladium. It floats readily with these materials and often is suppressed using guar gum or carboxy methyl cellulose which will absorb along the basal surface and make it hydrophilic. Alternately if the reduced ore is hydrophobic, like MoS2, then a partial oxidation of the sulfide will convert the surface to a hydrophilic oxide and the talc can be floated away in a separate step. Talc in grades from 20 to 90% has been commercially exploited in a wide range of pigment (paint and paper), material (ceramic, construction and cosmetic), reinforcing (polymers and composites) and functional (pitch adsorbent, lubricating agent) applications. Initially these tended to be local or regional markets, but eventually with certain higher purity grades, cosmetic, polymer and ceramic applications became valuable enough to be national and trans ocean markets. TALC FLOATATION PLANTS This drove the need for higher purity grades of talc and initially this need was met primarily by ore sorting. This works well for certain deposits with well crystallized talc lenses, but for ores, such as those from widely available ultramafic deposits, where the liberation size is closer to 100 microns, sorting is not effective. That drove the need for floatation and the first investigations were published by Clemmer and Cooke of the US Bureau of Mines in 19362. The first commercial floatation plant was installed in Johnson, VT by the Eastern Magnesia Talc Co in 1937. The circuit is shown in the schematic (Figure 1). The ore was an ultramafic, serpentine derived talc; mineralogy was about 55% talc, 40% ferroan magnesite and 5% oxides, sulfides and other silicates. The oxides include hematite and chromite, sulfides pyrite and gerstorffite and silicates chlorite, serpentine and mica. After crushing, the ore was dry ball milled and then air classified to remove minus 325 mesh fines. The coarse fraction was further classified to cut at about 100 mesh and the fines from this were the feed to floatation. The -325 mesh (about 15% of the ore) was sold as a paint grade and the plus 100 mesh (about 25% of the ore) was screened to make an asphalt backsurfacing grade."

Jan 1, 2018

By A. K. Smith

Overexposure to noise remains a widespread, serious health hazard in the U.S. mining industry. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. U.S. Mine Safety and Health Administration (MSHA) coal noise data from 2000-2004 show that the continuous mining machine (CMM) is first among all equipment, accounting for 35% of noise overexposures. Joy Mining Machinery, in collaboration with the National Institute for Occupational Safety and Health (NIOSH), is conducting research to reduce noise generated by continuous mining machines. This paper describes a "JOY Designed for Noise Reduction" (JOY DNR; patent pending) tail section as a noise control for reducing the noise overexposures of CMM operators. Underground testing shows a 45% to 65% noise exposure reduction for the operator when comparing the JOY DNR tail section results to those for a standard machine. Utilizing this newly developed noise control, along with previously proven controls, will provide CMM operators an opportunity to be within the MSHA permissible exposure limit (MSHA-PEL). Mining Engineering, 2011, Vol. 63, No. 7, pp. 83-85. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Lei Pan, Venkata Atluri, Xuming Wang, Yuesheng Gao, Jan D. Miller

Polysaccharides have been used as depressants for naturally hydrophobic talc in the flotation of base metal sulfide ores, precious metal sulfide ores and platinum group metal (PGM) sulfide ores. The results of this surface chemistry study confirm guar gum as a preferred polysaccharide for talc depression in the flotation of these ores. In addition to the practical application of the research results, the surface chemistry results are of academic significance, providing further information to understand how polysaccharide depressants function in these complex sulfide flotation systems.

By MAURICE SUNKPAL, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

In this study, various rib bolting scenarios were investigated to better understand the effectiveness of the support systems. A coal mass constitutive model is implemented to a distinct element method (DEM) code, and rib factor-of-safety (RibFOS) analyses were performed by applying strength reduction for the coal matrix and explicitly modeled face cleats. Ribs with various overburden depths and mining heights composed of solid banded bright coal were considered. Different scenarios such as rib bolt length and number of bolts were studied to quantify the effect of primary rib support density on rib stability. As a result of the unsupported coal rib analyses, a decaying exponential relationship is proposed between the mining height-overburden depth and the RibFOS. The developed coal rib models clearly show the coal-rib bolt interaction and illustrate how the addition of rib bolts restricts the movement of the coal rib. The results reveal that the strength-reduction method in DEM code with the coal-mass model can aid in the development of practical primary sup- port charts, which can help in the rib support design process.

Feb 1, 2024

By RALPH BALTES, AMIR EHSAN KIANFAR, FABIAN UTH, ELISABETH CLAUSEN

  Underground positioning and communication are essential technologies for the future of underground mining operations. In contrast to other positioning and communication technologies such as wireless local area network (WLAN) or radio frequency identification (RFID), ultra-wideband (UWB) radio technology provides significant benefits like accurate and robust positioning of mobile machine equipment, which is indispensable for future autonomous systems in underground mining processes, such as production, transportation and auxiliary operations. Among these technologies, UWB offers many advantages, including higher accuracy, robustness, resistance against noise and multipath effects, and low power consumption [1,2]. Underground automation and localization systems benefit from these advantages and use the technology to improve efficiency and safety. There are many studies being carried out on this technology to increase the results’ accuracy, energy sufficiency and more. Two robust UWB modules that were developed for underground positioning and collision avoidance with regard to human safety in underground mining operations are introduced. The measurement results of tests carried out in an underground mine are discussed as well to confirm the functionality of the system.

By RICKARD HANSEN

With vehicles frequently found in mines and tires being a major fuel item, the risk of tire fires will be severe underground. This study presents an analysis of tire fires on mining vehicles to increase the knowledge of the risk and mitigating measures, which would improve the fire safety underground. Data from fire experiments and computational fluid dynamics (CFD) simulations were applied. It was found that the wheelhouse of a loader caused an increase in the flame tilt angle, decreasing the flame impingement and heat flux downstream. The flame temperature of a drilling rig tire was found to be higher than that of a loader tire, increasing the risk of igniting items. The construction of the wheelhouse/mudguard will contribute to a longer flame length by creating a fuel-rich environment. The CFD simulations predicted higher flame tilt angles for a drilling rig for higher flow velocities, indicating the influence of the wheelhouse/mudguard construction and tire geometry on the flame tilt angle. The construction of a loader resulted in flow behavior, where the short distance to the front mudguard/tire and the separation of flow directly downstream of the construction led to gases being steered past the front mudguard/tire. In a drilling rig case, the longer distance to the front mudguard/tire led to gases being directed toward the body of the vehicle after passing the area with flow separation.

By Liming Yuan, Isaac Zlochower, RICHARD THOMAS, Thomas H. Dubaniewicz, Teresa Barone

Mining vehicle manufacturers are developing lithium-ion (Li-ion) battery electric vehicles as an alternative to diesel-powered vehicles. In gassy underground mines, explosion-proof enclosures are commonly used to enclose electrical ignition sources to prevent propagation of an internal methane (CH4)-air explosion to a surrounding explosive atmosphere. Li-ion batteries can create pressurized explosions within sealed enclosures due to thermal runaway. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) measured thermal-runaway pressures of lithium iron phosphate (LFP) cells as a function of free space within sealed enclosures and observed an inverse power relationship. A well-confined cell produced 4260 psia (294 bar) of pressure during a thermal runaway, far exceeding minimum pressure containment specifications for conventional explosion-proof enclosures. Results indicate that adding enough free space surrounding LFP cells can reduce thermal-runaway pressures to levels below that expected for CH4-air ignitions. Measured thermal-runaway temperatures were below the minimum autoignition temperature of CH4-air.

We have lived through a period of strong metal pricing during the past eight to 10 years. Copper has been hovering in the range of $3-$4/lb during much of the past eight years, averaging close to $3.30/lb. Gold increased steadily from less than $300/oz levels in the early 2000s, reaching almost $1,890/oz in the third quarter of 2011, before tempering back down to the $1,200-1,400/oz range in 2013. Iron ore prices started to rise in 2005 before the staggering increases experienced in 2008- 2010, reaching almost $190/metric ton in early 2011. During the past four years, iron ore prices have ranged from $100-180/t, averaging approximately $140/t. In the aftermath of such a run, it is perhaps too easy to forget where we have come from: The copper price averaged just 77 cents/lb during the six-year period from 1998 to 2003, and averaged just over $1/lb from 1989 to 1997. The gold price averaged $350/oz during the 10-year period from 1994 to 2003. Even more dramatically, iron ore traded in the range of $10-$15/t between 1985 and 2004. So, we have seen sustained, three- to four-fold increases in copper and gold prices, and 8 to 10-fold increases in iron ore prices.

Mar 1, 2014

The authors provide a discussion of the paper, ?Coal workers? pneumoconiosis prevalence disparity between australia and the united States,? a peer-reviewed paper that appeared in the technical papers section of the July 2012 issue of Mining Engineering magazine. The original authors, G.J. Joy (gjoy@cdc.gov), J.F. Colinet (jcolinet@cdc.gov) and D.D. Landen (dlanden@cdc.gov), respond.

Jan 1, 2013

The National Mining Hall of Fame and Museum (NMHFM) in Leadville, CO will induct the class of 2011 on Sept. 10, 2011. Representing the coal, metallurgical/processing, research and development, marble and lead industries, this year?s inductees cover a diverse crosssection of the mining industry. William Francis Diamond, Wayne Hazen, Redfield Proctor and Jeffrey Zelms will join 210 other mining industry pioneers when they are formally inducted into the National Mining Hall of Fame at the 24th Annual Induction Banquet and Ceremony. The members of this year?s class were selected for being visionaries, leaders and ambassadors both within their own sectors and across the industry at large. Diamond had an illustrious engineering and managerial career that spanned four decades with Island Creek Coal Co. During that time, he was responsible for the engineering and construction of the deepest coal mines producing in North America at the time.

Jan 1, 2011

By G. A. Christie

This paper presents a vision system capable of providing an accurate estimate for the volume of stockpiles using 2D images. By imaging a stockpile from multiple viewpoints with a two-camera system, a 3D point cloud of known scale is generated using image-based 3D reconstructions. With a small amount of user interaction, the points that correspond to the surface of the stockpile are extracted and used to measure the volume. The hardware required for the two-camera system is light enough to be carried by a small unmanned aircraft and is a cheaper alternative to LiDAR while still being competitive in terms of accuracy. When testing the volume measurement algorithm on a stockpile of known volume, the measured output was found to have less than a 3% error from the ground truth.