Search Documents

By T. P. Weldum, W. Conger

"The objective of the study conducted by the authors is to determine what media size(s) addition will maximize any given plant ball mill’s grinding efficiency (Fig. 1). The functional performance parameters “mill grinding rate through the size of interest,” and “cumulative mill grinding rates” from both plant and smallscale tests are applied to this task. A plant media sizing methodology, and industrial case studies, are provided.BackgroundA previous article (“Ball mill classification system optimization through functional performance modeling,” Nov. 17, McIvor et al., 2017, Mining Engineering) described circuit classification system efficiency (CSE), equal to the percentage of coarse (plus circuit P80 target size) material in the ball mill. It can be measured and then increased through pump and cyclone adjustments. By so transferring the application of ball mill power from fine (minus P80 product size) to coarse material, circuit efficiency is increased and overgrinding is decreased.The other factor that determines overall circuit efficiency is how well the power that is applied to the coarse material grinds it. This is affected by design and operating variables like the media sizing and mill percent solids. From circuit functional performance (McIvor et al., 1990):Circuit production rate of new fine material (t/h) = Power applied to coarse material (kW) x Mill grinding rate of coarse material (t/kWh) (1)The power applied to coarse material is the total mill power multiplied by the CSE. Therefore:Circuit production rate of new fine material (t/h) = Total mill power (kW) x CSE (%) x Mill grinding rate of coarse material (t/kWh) (2) Production rate, mill power and CSE can be measured during a plant circuit survey. The mill grinding rate of coarse material is then calculated. At the circuit target P80 size, this is the mill grinding rate (of coarse material) through the size of interest. The objective is to maximize this rate. The mill grinding efficiency can also be calculated by taking the ratio of the mill grinding rate over the material’s grindability as measured in the lab. Mill percent solids optimization has thusly been achieved (McIvor et al., 2000). For media sizing, maximizing the mill grinding rate on a given ore is equivalent to maximizing the mill grinding efficiency. Ores of different grindability will be part of the discussion."

Jan 11, 2018

By Richard J. Leary

At the 1976 Annual Meeting of AIDE, Alan Merson reminded his audience that economic' success comes to those who understand things as they are, rather than as they have been or what ideology says they should be (1). He went on to say that, measured by this standard, the mining industry is in trouble. The mining firms had recognized long ago the importance of effective lobbying in Washington and the state capitals. But, he pointed out, those methods are nearly worthless anymore in coping with many land use problems because the critical decisions are likely to be made at the local level. There the tactics are far different as are the relations of the decisionmakers to the parties before then. Furthermore, in his estimation the trend is to leave land use regulation largely to the local level of government. All who are concerned for access to land for mineral development will be benefited by reading Professor Merson's paper lie is speaking effectively about the context of decisionmaking for specific cases, the shape of things in the here and now. There is, however, a longer-tern set of considerations that if pursued will be likely to foster the creation of public support for mining developments. At that sane meeting I spoke on two foundations of the long-term relationships: namely, the growth in requirements for minerals implied by projections of increasing consumption; and a rationale for fostering mineral exploration and development. I mentioned in passing the social decisionmaking process for public uses of land (2). This paper is intended as a complement. The growth of requirements for Minerals and the rationale for development based on the Entropy Law will be only mentioned. The main concern will be on the process of social decisionmaking in the context of access to land for mineral development.

Jan 1, 1976

By K. K. Wu

In some cases, coal barrier pillars must be relied on to withstand high hydrostatic pressures in order to prevent inundation of active mine workings. Such barriers are particularly important in areas, such as parts of West Virginia, where much of the future mining is down dip of mines which have been abandoned, or are currently being worked. Also, where multiple seam mining is conducted, a barrier pillar in one mine may be critical to safety in a mine in a lower seam. MSHA's Coal Mine Safety and Health district offices and the Mine Waste and Geotechnical Engineering Branch of the Pittsburgh Technical Support Center, have recently been involved in the study of barrier pillars in Kentucky, Virginia, West Virginia, Ohio and Oklahoma. In this paper, the factors involved in determining the required width of pillar are discussed, past practices for sizing barriers are reviewed, and related current Federal regulations are examined. In addition, the results of laboratory testing of bottom rock are presented.

Jan 1, 1980

By David J. Brown

Extensive deposits of bituminous, subbituminous, and lignite coals occur in the western United States (Figure 1). Over one trillion tons of identified resources have been located and inferred by geologists and more than 200 million tons of western coal are mined annually (1). In the future, production of western coals will increase significantly and approach national production levels of higher-rank eastern coals. Western coals will be utilized in new power plants as a replacement fuel for oil and gas and may be used in advanced technologies such as diesel engines or in direct-fired turbines. Since these applications require low-ash, low-sulfur coals, crushing to fine sizes and significant cleaning to remove minerals and sulfur will be required. Coal cleaning traditionally has been associated with reducing pyrite and other mineral matter from high-rank eastern coals. To date, insignificant quantities of western coals have been cleaned before utilization and limited data on their washability characteristics exist. Because of this lack of data, it is difficult to predict how these coals will react to standard washing techniques.

Jan 1, 1985

By B. DANIEL MARJAVAARA, I. A. SOFIA LARSSON, ANNA-LENA LJUNG

One way to upgrade iron ore is to process it into pellets. The pelletizing process is multifaceted, involving complex fluid dynamics with highly turbulent, high-temperature flow in intricate geometries. This makes it hard to perform measurements during operation, so a useful tool for better process understanding is computational fluid dynamics (CFD), where the challenge is to perform efficient and trustful simulations of complicated problems. A validated simulation model can be valuable for increased process control and development. In this paper, the flow field and coal combustion process in a pilot-scale iron-ore pelletizing kiln is simulated using a CFD model. The objective of this work is to apply a coal combustion model to enable an investigation of thermal effects from the flame on the surrounding flow field.

By Edmundo Tulcanaza

Increasing exploration costs and the need to reduce the time-frame from exploration to production presently demand formalized procedures to assist exploration planning and reserve analysis. Exploration planning is basically required to select the most cost-effective drilling/sampling program, and to flag the needs for data of greater relevance and reliability. Reserve analysis is necessary to determine the sensitivity of grade-tonnage relations, and to clarify the economic implications of mining when alternative technical choices are to be considered.

Jan 1, 1982

By C. Roos

Traditionally within the mining industry, the main functional process flow for resource and reserve evaluation proceeds from geologists who build the geological model, to resource estimation geologists (modelers) who estimate the grades, to mining engineers who develop the mine design and schedule. The interface between these three disciplines is not always seamless. Assumptions made during one stage of the process are not always communicated down the line, even though most mining companies have procedures in place to encourage communication across the various disciplines. These procedures do not always achieve their aim due to a variety of reasons including time constraints, appropriate people not being available, or a lack of understanding of what other disciplines require, and the handover process can degenerate into one of sending computer files on to the next discipline in the process flow. This paper focuses on the interface between the resource estimation and mine engineering disciplines, and outlines some of the common assumptions made when generating a resource model and the risks that engineers may be taking when elevating cutoff grades, optimizing schedules or generating forecasts. The case studies presented focus on openpit gold deposits, but the concepts should be applicable throughout the industry. A summary of key questions and recommendations is provided.

Jan 1, 2014

By A. Newman, A. Brickey

Although some of the prevalence of openpit production scheduling software can be explained by the predominance of openpit mining throughout the world, other factors have led to a lag in corresponding underground software. We explain mathematically why underground production scheduling is more difficult than its openpit counterpart and provide directions for research in the underground scheduling arena.

Jan 1, 2014

By A. Newman, A. Brickey

A pesar de que parte del predominio de software de programación de producción a cielo abierto se puede explicar por la preponderancia de la minería a cielo abierto en todo el mundo, hay otros factores que han dado lugar a un retraso en el software subterráneo correspondiente. Explicamos por qué matemáticamente la programación de la producción subterránea es más difícil que su contraparte a cielo abierto y daremos pautas para la investigación en el campo de la programación subterránea.

Jan 1, 2014

By C. Roos

Tradicionalmente en la industria minera, el flujo principal del proceso funcional para la evaluación de recursos y reservas procede de geólogos que elaboran el modelo geológico, de allí a los geólogos que hacen la estimación de los recursos (los modeladores) quienes estiman los grados, y a los ingenieros de mina que desarrollan el diseño de la mina y su calendario. La interfaz entre estas tres disciplinas no está siempre exenta de baches. Las presunciones hechas durante una etapa del proceso no siempre son comunicadas a los demás, a pesar que la mayoría de las empresas mineras tienen procedimientos y protocolos establecidos para promover la comunicación a lo largo de las distintas disciplinas. Estos procedimientos no siempre logran su propósito debido a una variedad de razones que incluyen restricciones de tiempo, no tener disponible a las personas apropiadas, o a una falta de entendimiento de lo que las otras disciplinas requieren, y el proceso de traspaso puede degenerar en el envío de archivos a la siguiente disciplina en el flujo de proceso. Este artículo se ocupa de la interfaz entre la estimación del recurso y las disciplinas de la ingeniería de minas y el esquema de algunas de las presunciones comunes hechas al generar un modelo del recurso y los riesgos que los ingenieros podrían correr al elevar los grados de corte, optimizar calendarios o realizar predicciones. Los casos de estudio presentados se centran en depósitos de oro a cielo abierto, pero los conceptos deben ser aplicables a toda la industria. Aquí también proveemos un resumen de preguntas clave y recomendaciones.

Jan 1, 2014

By Karl R. Zipf

A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine. The gas samples are drawn via vacuum pump to the surface and are typically analyzed for oxygen, methane, carbon dioxide and carbon monoxide. Results of the gas analyses are displayed and recorded for further analysis. Trends in the composition of the mine atmosphere, such as increasing methane or carbon monoxide concentration, can be detected early, permitting rapid intervention that prevents problems, such as a potentially explosive atmosphere behind seals, fie or spontaneous combustion. TBS is a well-developed technology and has been used in coal mines around the world for more than 50 years. most longwall coal mines in australia deploy a TBS, usually with 30 to 40 monitoring points as part of their atmospheric monitoring. The primary uses of a TBS are detecting spontaneous combustion and maintaining sealed areas inert. The TBS might also provide mine atmosphere gas composition data after a catastrophe occurs in an underground mine, if the sampling tubes are not damaged. TBSs are not an alternative to statutory gas and ventilation airflowmonitoring by electronic sensors or people; rather, they are an option to consider in an overall mine atmosphere monitoring strategy. This paper describes the hardware, software and operation of a TBS and presents one example of typical data from a longwall coal mine.

May 1, 2013

By C. D. Litton, I. E. Perera

This report presents the results of experiments to evaluate different types of mine fire sensors in an underground mine environment using a commercially available atmospheric monitoring system. To determine how well carbon monoxide (CO) and smoke sensors respond for purposes of fire detection, experiments were conducted using test fires of different mine combustibles and for both flaming and nonflaming combustion. The experiments were designed to assess the response of fire sensors to different contaminants and different contaminant levels produced from the test fires. The experiments were performed in the Safety Research Coal Mine at the U.S. National Institute for Occupational Safety and Health’s Bruceton Research Facility in the presence of an average ventilating air velocity of 1.6 m/s (315 fpm). Five fire sensor stations were located downstream of the test fire at fixed locations, with each sensor station consisting of four sensors: a CO fire sensor and three different smoke sensors, of which two were evaluated by the Mine Safety and Health Administration (MSHA) for intrinsic safety and the third was used extensively in underground mines overseas but not evaluated by MSHA for intrinsic safety. All four sensors were mounted near the center of the entry and in the upper onethird of the entry height. A UL-listed combination ionization and photoelectric smoke sensor was mounted near the roof at the first sensor station and its responses were compared against the responses of the four CO and smoke fire sensors. Sensor response data, contaminant travel times, and the impact of fire on the existing ventilation flow are discussed as they apply to earlywarning fire detection. Of significance in the analysis is the need for performance standards for mine fire sensors in order to provide for consistent and timely early warning of developing fires.

Jan 1, 2014

By O. F. Brown

Excavation and loading are primary operations in the surface mine production chain, constituting a significant component of production costs. This makes excavation and loading important cost centers that need to be improved to lower production costs. Optimizing the design and use of excavators will improve energy efficiency in earthmoving operations, and this requires a thorough understanding of the soil-tool interaction process. Modeling the interaction process accurately is the key to this optimization. Experimental and analytical methods have provided limited information on the behavior of soils during excavation. Finite element (Fe) analysis of soil-cutting blade interaction produces some advantages over experimental and analytical methods. However, the soil constitutive equations used in most of the available Fe analyses fail to adequately model the plastic behavior of the soil. This work uses Fe modeling to study the behavior of formation-cutting blade interactions in dozer excavation. The formation is modeled as a nonlinear elastoplastic material using the modified cam-clay (mCC) model. The model accounts for soil-tool interface friction, and progressive and continuous cutting at the blade tip. The results provide soil forces, a progressive developed failure zone and soil displacement fields. The sensitivity analysis of changes in blade angle on cutting force shows that the cutting force increases with increasing blade angle. The cutting depth of the blade had a similar effect on blade cutting force. Increasing the depth of cut increases the required cutting force. Increasing the coefficient of friction at the soil blade interface increases the blade cutting force. Reducing the coefficient of friction at the soil blade interface from 0.3 to 0.05 reduces the cutting force by 22.3%. The percentage represents the maximum potential savings in blade cutting force. This research initiative advances the frontiers of soil-tool interactions during excavations to expand the limited knowledge in this critical area.

Jan 1, 2012

By Irwan Halim, Bhoshaga Mitrran Ravi Chandran, Kevin Huynh

Tunnel segmental lining design constitutes a significant iterative process where modeling and numerical analysis are factors in deciding the number of segments, their dimensions, gasket placements, as well as the locations of dowels and bolts. Consequently, these modifications lead to revisions in the final drawing details. However, the current tunnel engineering practices lack systematic solutions that effectively bridge the gap between the iterative design process and efficient visualization of completed drawings due to the time- consuming nature of redrawing. This paper presents a pioneering application of AI-driven solutions including using Autodesk's API, for the Northside Interceptor Tunnel (NSIT) Project. It showcases the automation of drawing design and the real-time visualization of modifications, thereby streamlining the drawing process.

Jun 23, 2024

By E. Jong, E. Watkins

"The application of passive tracer gas sources in underground mines is particularly useful for long-term tracer studies as well as for studies conducted in permissible areas of underground coal mines. The use of passive perfluoromethylcyclohexane (PMCH) sources has been previously demonstrated in underground mines, but this new work details the testing of multiple, distinct tracer compounds compatible with passive sources. A description of their potential application in mine ventilation systems is also provided. Three tracer compounds are detailed: (1) PMCH, (2) perfluoroethylcyclohexane (PECH) and perfluoromethylcyclopentane (PMCP). The release rates of these tracers were examined over a 180-day period at multiple temperatures. The advantages and disadvantages of these sources are presented, along with potential applications in characterizing ventilation circuits, flow through gob and leakage. IntroductionThe use of tracer gases for ventilation applications is an established practice, with various past research projects conducted using sulfur hexafluoride (SF6). Tracer gas techniques have been applied to assess flow rates, dilutions rates and auxiliary ventilation system efficiencies with quick, reliable and accurate results (Suglo and Frimpong, 2002). Perfluorocarbon tracer (PFT) compounds are a new introduction to ventilation and air modeling applications in terms of ventilation flow characterization (Watson et al., 2007).PFTs are liquids that are characterized by low background presence in air, low reactivity, high detectability and low toxicity. A design was proposed, called a permeation plug release vessel (PPRV), to convert PFTs from a liquid to a gas and then release the gaseous tracer in a controlled manner. The initial concept was originally introduced by Brookhaven National Laboratory and refined later to become the PPRV. The PPRV functions by allowing the volatile PFT liquid to become a vapor in a controlled manner. The vapor diffuses through a permeable silicone stopper at a predictable rate proportional to temperature (Zhang and Cloud, 2006)."

Jan 2, 2018

By Andreas Eberhorn

The evaluation criteria for cost comparison of the Gearless Drive, also called Ringmotor or wrap-around motor, as variable-speed drive with a Twin Drive System using synchronous motors are reviewed. Both mechanical and electrical components of the drive system are considered. The evaluation criteria are described and for the cost comparison the applicable method is demonstrated. The cost comparison is based on a medium and large sized mill system. Each drive package will display cost details with regard to capital cost, maintenance, power losses, overall efficiency, overhead and loss of production. As conclusion the benefits and disadvantages of the two drive/mill packages will be presented together with a payback diagram.

Jan 1, 1996

By W. E. Horst

In Part I of this paper we describe two techniques that were employed in the development of mathematical descriptions of the size reduction process which takes place in a ball mill. In Part II we show how the comminution model was imbedded in a process model to effect steady-state and dynamic simulation of a closed-circuit grinding operation. Increasing emphasis is being placed on development of approaches whereby the essential characteristics of a process can be succinctly represented in terms of a mathematical description of the relationships that exist among important process variables. This activity, commonly known as mathematical modeling, predates modern electronic computers: however, these computers with their tremendous computational capability have given new impetus to the whole field. Although the computer is quite helpful in the development of mathematical models, the real value to the engineer lies in the fact that computers represent such a powerful tool for simulating systems described by mathematical models. As a consequence, engineers may simulate and thereby study the behavior of complex. interacting, systems over a broad range of process variables and configurations once appropriate process models have been developed for the sequence of steps comprising the process.

Jan 1, 1970

By T. E. Burns

The process engineer is frequently requested to select equipment to separate brine from solids, In many cases, this is a more difficult task than the selection of most other pieces of process equipment because quite often the operation of the various types of debrining equipment cannot be predicted by calculations, One must rely to a great extent upon experience or empirical test work to predict performance - that is to say one must use a practical rather than a theoretical approach. This is not to say that the solutions to liquid-solids separating problems are wholly an art but rather it is to emphasize that the approach demands a fair knowledge of commercially available liquid-solids separating equipment, some background on the advantages and limitations of each type and in many cases might necessitate a fair amount of test work, or at least, a study of performance of equipment on similar applications.

Jan 1, 1966

By Kim B. Shedd, Erin A. McCullough, Donald I. Bleiwas

"The earliest known use of cobalt was to make blue glass in Mesopotamia before 2000 B.C.E. Since then, innovations across many diverse industrial sectors transformed cobalt into an essential commodity for contemporary society. The physical and chemical properties of the element cobalt and its alloys and compounds make them indispensable for a variety of applications, including aircraft engines, hybrid electric vehicles, machine tools, missile guidance systems, petroleum refining and smartphones. As a major industrialized nation, the United States is a leading consumer of cobalt and cobalt-containing products. However, with few exceptions, U.S. cobaltcontaining ore deposits are of low cobalt grade. Historically, U.S. cobalt mine and refinery output have not met domestic cobalt demand. As a result, U.S. cobalt chemical and alloy producers need to procure most of their cobalt from the international market, which can become susceptible to supply risk.The 1978 Cobalt Crisis illustrates supply risk. At that time, the Democratic Republic of the Congo (DRC) (then known as Zaire) was the world’s leading producer of mined and refined cobalt. An insurgent invasion of the country’s copper-cobalt mining region during a period of high cobalt demand and low producer inventories caused a temporary supply shortage in the international market. The monthly average cobalt spot price increased from $18/ kg ($8/lb) before the crisis to $99/kg ($45/lb) seven months later. The high price and concern about potential disruptions in supply prompted manufacturers to reduce or substitute for cobalt where possible, and encouraged increased recovery of cobalt from scrap. The DRC has regained its position as the leading producer of mined cobalt globally and continues to be characterized by high governance risks (U.S. Central Intelligence Agency, 2015; World Bank, undated). This article will present current and historical world cobalt production trends, which can help inform discussion about the variety of international supply chain risks consequential to its trade."

Jan 12, 2017

By C. J. Pritchard

The Office of Mine Safety and Health Research (OMSHR) investigated ways to increase mine airflow to underground metal/nonmetal (M/NM) mine working areas to improve miners? health and safety. One of those areas is controlled recirculation. Because the quantity of mine air often cannot be increased, reusing part of the ventilating air can be an effective alternative, if implemented properly, until the capacity of the present system is improved. The additional airflow can be used to provide effective dilution of contaminants and higher flow velocities in the underground mine environment. Most applications of controlled recirculation involve taking a portion of the return air and passing it back into the intake to increase the air volume delivered to the desired work areas. OMSHR investigated a Nevada gold mine where shaft rehabilitation was in progress and one of the two main fans was shut down to allow reduced air velocity for safe shaft work. Underground booster fan operating pressures were kept constant to maintain airflow to work areas, inducing controlled recirculation in one work zone. Investigation into system behavior and the effects of recirculation on the working area during times of reduced primary ventilation system airflow would provide additional information on implementation of controlled recirculation into the system and how these events affect M/NM ventilation systems. The National Institute for Occupational Safety and Health monitored the ventilation district when both main fans were operating and another scenario with one of the units turned off for maintenance. Airflow and contaminants were measured to determine the exposure effects of induced recirculation on miner health. Surveys showed that 19% controlled recirculation created no change in the overall district airflow distribution and a small reduction in district fresh air intake. Total dust levels increased only modestly and respirable dust levels were also low. Diesel particulate matter (DPM) levels showed a high increase in district intake mass flow, but minor increases in exposure levels related to the recirculation percentage. Utilization of DPM mass flow rates allows input into ventilation modeling programs to better understand and plan for ventilation changes and district recirculation effects on miners? health.